Abstract: This paper proposes five level diode clamped Z source
Inverter. The existing PWM techniques used for ZSI are restricted for
two level. The two level Z Source Inverter have high harmonic
distortions which effects the performance of the grid connected PV
system. To improve the performance of the system the number of
voltage levels in the output waveform need to be increased. This
paper presents comparative analysis of a five level diode clamped Z
source Inverter with different carrier based Modified Pulse Width
Modulation techniques. The parameters considered for comparison
are output voltage, voltage gain, voltage stress across switch and total
harmonic distortion when powered by same DC supply. Analytical
results are verified using MATLAB.
Abstract: Using the pseudopotential technique the Sagdeev
potential equation has been derived in a plasma consisting of twotemperature
nonisothermal electrons, negatively charged dust grains
and warm positive ions. The study shows that the presence of
nonisothermal two-temperature electrons and charged dust grains
have significant effects on the excitation and structure of the ionacoustic
double layers in the model plasma under consideration. Only
compressive type double layer is obtained in the present plasma
model. The double layer solution has also been obtained by including
higher order nonlinearity and nonisothermality, which is shown to
modify the amplitude and deform the shape of the double layer.
Abstract: Exact solution of an unsteady flow of elastico-viscous
fluid through a porous media in a tube of ellipsoidal cross section
under the influence of constant pressure gradient has been obtained in
this paper. Initially, the flow is generated by a constant pressure
gradient. After attaining the steady state, the pressure gradient is
suddenly withdrawn and the resulting fluid motion in a tube of
ellipsoidal cross section by taking into account of the porosity factor
of the bounding surface is investigated. The problem is solved in twostages
the first stage is a steady motion in tube under the influence of
a constant pressure gradient, the second stage concern with an
unsteady motion. The problem is solved employing separation of
variables technique. The results are expressed in terms of a nondimensional
porosity parameter (K) and elastico-viscosity parameter
(β), which depends on the Non-Newtonian coefficient. The flow
parameters are found to be identical with that of Newtonian case as
elastic-viscosity parameter tends to zero and porosity tends to
infinity. It is seen that the effect of elastico-viscosity parameter and
the porosity parameter of the bounding surface has significant effect
on the velocity parameter.
Abstract: Customer churn prediction is one of the most useful
areas of study in customer analytics. Due to the enormous amount
of data available for such predictions, machine learning and data
mining have been heavily used in this domain. There exist many
machine learning algorithms directly applicable for the problem of
customer churn prediction, and here, we attempt to experiment on
a novel approach by using a cognitive learning based technique in
an attempt to improve the results obtained by using a combination
of supervised learning methods, with cognitive unsupervised learning
methods.
Abstract: Nowadays, huge amount of multimedia repositories
make the browsing, retrieval and delivery of video contents very slow
and even difficult tasks. Video summarization has been proposed to
improve faster browsing of large video collections and more efficient
content indexing and access. In this paper, we focus on approaches to
video summarization. The video summaries can be generated in many
different forms. However, two fundamentals ways to generate
summaries are static and dynamic. We present different techniques
for each mode in the literature and describe some features used for
generating video summaries. We conclude with perspective for
further research.
Abstract: In this paper we are presenting some spamming
techniques their behaviour and possible solutions. We have analyzed
how Spammers enters into online social networking sites (OSNSs) to
target them and diverse techniques used by them for this purpose.
Spamming is very common issue in present era of Internet
especially through Online Social Networking Sites (like Facebook,
Twitter, and Google+ etc.). Spam messages keep wasting Internet
bandwidth and the storage space of servers. On social networking
sites; spammers often disguise themselves by creating fake accounts
and hijacking user’s accounts for personal gains. They behave like
normal user and they continue to change their spamming strategy.
Following spamming techniques are discussed in this paper like
clickjacking, social engineered attacks, cross site scripting, URL
shortening, and drive by download. We have used elgg framework
for demonstration of some of spamming threats and respective
implementation of solutions.
Abstract: Hurling a successful Construction and Demolition
Waste (C&DW) recycling operation around the globe is a challenge
today, predominantly because secondary materials markets are yet to
be integrated. Reducing, Reusing and recycling of (C&DW) have
been employed over the years, and various techniques have been
investigated. However, the economic and environmental viability of
its application seems limited. This paper discusses the costs and
benefits in using secondary materials and focus on investigating reuse
and recycling process for five major types of construction materials:
concrete, metal, wood, cardboard/paper and plasterboard. Data
obtained from demolition specialists and contractors are considered
and evaluated. The research paper found that construction material
recovery process fully incorporate a 3R’s principle contributing to
saving energy and natural resources. This scrutiny leads to the
empathy of grand challenges in construction material recovery
process. Recommendations to deepen material recovery process are
also discussed.
Abstract: Enterococci are important inhabitants of the animal
intestine and are widely used in probiotic products. A probiotic strain
is expected to possess several desirable properties in order to exert
beneficial effects. Therefore, the objective of this study was to
isolate, characterize and identify Enterococcus sp. from chicken cecal
and fecal samples to determine potential probiotic properties.
Enterococci were isolated from chicken ceca and feces of thirty three
clinically healthy chickens from a local farm. In vitro studies were
performed to assess antibacterial activity of the isolated LAB (using
agar well diffusion and cell free supernatant broth technique against
Salmonella enterica serotype Enteritidis), survival in acidic
conditions, resistance to bile salts, and their survival during simulated
gastric juice conditions at pH 2.5. Isolates were identified by
biochemical carbohydrate fermentation patterns using an API 50
CHL kit and API ZYM kits and by sequenced 16S rDNA. An isolate
belonging to E. faecium species exhibited inhibitory effect against S.
enteritidis. This isolate producing a clear zone as large as 10.30 mm
or greater and was able to grow in the coculture medium and at the
same time, inhibited the growth S. enteritidis. In addition, E. faecium
exhibited significant resistance under highly acidic conditions at pH
2.5 for 8 h and survived well in bile salt at 0.2% for 24 h and showing
ability to survive in the presence of simulated gastric juice at pH 2.5.
Based on these results, E. faecium isolate fulfills some of the criteria
to be considered as a probiotic strain and therefore, could be used as a
feed additive with good potential for controlling S. Enteritidis in
chickens. However, in vivo studies are needed to determine the safety
of the strain.
Abstract: In this paper, the problem of fault detection and
isolation in the attitude control subsystem of spacecraft formation
flying is considered. In order to design the fault detection method, an
extended Kalman filter is utilized which is a nonlinear stochastic state
estimation method. Three fault detection architectures, namely,
centralized, decentralized, and semi-decentralized are designed based
on the extended Kalman filters. Moreover, the residual generation
and threshold selection techniques are proposed for these
architectures.
Abstract: Over the past four decades, the fatigue behavior of
nickel-based alloys has been widely studied. However, in recent
years, significant advances in the fabrication process leading to grain
size reduction have been made in order to improve fatigue properties
of aircraft turbine discs. Indeed, a change in particle size affects the
initiation mode of fatigue cracks as well as the fatigue life of the
material. The present study aims to investigate the fatigue behavior of
a newly developed nickel-based superalloy under biaxial-planar
loading. Low Cycle Fatigue (LCF) tests are performed at different
stress ratios so as to study the influence of the multiaxial stress state
on the fatigue life of the material. Full-field displacement and strain
measurements as well as crack initiation detection are obtained using
Digital Image Correlation (DIC) techniques. The aim of this
presentation is first to provide an in-depth description of both the
experimental set-up and protocol: the multiaxial testing machine, the
specific design of the cruciform specimen and performances of the
DIC code are introduced. Second, results for sixteen specimens
related to different load ratios are presented. Crack detection, strain
amplitude and number of cycles to crack initiation vs. triaxial stress
ratio for each loading case are given. Third, from fractographic
investigations by scanning electron microscopy it is found that the
mechanism of fatigue crack initiation does not depend on the triaxial
stress ratio and that most fatigue cracks initiate from subsurface
carbides.
Abstract: In this work, we report, a systematic study on the
structural and optical properties of Pr-doped ZnO nanostructures and
PVA:Zn98Pr2O polymer matrix nanocomposites free standing films.
These particles are synthesized through simple wet chemical route
and solution casting technique at room temperature, respectively.
Structural studies carried out by X-ray diffraction method confirm
that the prepared pure ZnO and Pr doped ZnO nanostructures are in
hexagonal wurtzite structure and the microstrain is increased upon
doping. TEM analysis reveals that the prepared materials are in sheet
like nature. Absorption spectra show free excitonic absorption band
at 370 nm and red shift for the Pr doped ZnO nanostructures. The
PVA:Zn98Pr2O composite film exhibits both free excitonic and PVA
absorption bands at 282 nm. Fourier transform infrared spectral
studies confirm the presence of A1 (TO) and E1 (TO) modes of Zn-O
bond vibration and the formation of polymer composite materials.
Abstract: In this paper, we used data mining to extract
biomedical knowledge. In general, complex biomedical data
collected in studies of populations are treated by statistical methods,
although they are robust, they are not sufficient in themselves to
harness the potential wealth of data. For that you used in step two
learning algorithms: the Decision Trees and Support Vector Machine
(SVM). These supervised classification methods are used to make the
diagnosis of thyroid disease. In this context, we propose to promote
the study and use of symbolic data mining techniques.
Abstract: Electroencephalogram (EEG) is a noninvasive
technique that registers signals originating from the firing of neurons
in the brain. The Emotiv EEG Neuroheadset is a consumer product
comprised of 14 EEG channels and was used to record the reactions
of the neurons within the brain to two forms of stimuli in 10
participants. These stimuli consisted of auditory and visual formats
that provided directions of ‘right’ or ‘left.’ Participants were
instructed to raise their right or left arm in accordance with the
instruction given. A scenario in OpenViBE was generated to both
stimulate the participants while recording their data. In OpenViBE,
the Graz Motor BCI Stimulator algorithm was configured to govern
the duration and number of visual stimuli. Utilizing EEGLAB under
the cross platform MATLAB®, the electrodes most stimulated during
the study were defined. Data outputs from EEGLAB were analyzed
using IBM SPSS Statistics® Version 20. This aided in determining
the electrodes to use in the development of a brain-machine interface
(BMI) using real-time EEG signals from the Emotiv EEG
Neuroheadset. Signal processing and feature extraction were
accomplished via the Simulink® signal processing toolbox. An
Arduino™ Duemilanove microcontroller was used to link the Emotiv
EEG Neuroheadset and the right and left Mecha TE™ Hands.
Abstract: In this paper, reliable consensus of multi-agent systems
with sampled-data is investigated. By using a suitable
Lyapunov-Krasovskii functional and some techniques such as
Wirtinger Inequality, Schur Complement and Kronecker Product, the
results of such system are obtained by solving a set of Linear Matrix
Inequalities (LMIs). One numerical example is included to show the
effectiveness of the proposed criteria.
Abstract: This paper presents powerful techniques for the
development of a new monitoring method based on multi-scale
entropy (MSE) in order to characterize the behaviour of the
concentrations of different gases present in the synthesis of Ammonia
and soft-sensor based on Principal Component Analysis (PCA).
Abstract: This paper presents two techniques, local feature
extraction using image spectrum and low frequency spectrum
modelling using GMM to capture the underlying statistical
information to improve the performance of face recognition
system. Local spectrum features are extracted using overlap sub
block window that are mapped on the face image. For each of this
block, spatial domain is transformed to frequency domain using
DFT. A low frequency coefficient is preserved by discarding high
frequency coefficients by applying rectangular mask on the
spectrum of the facial image. Low frequency information is non-
Gaussian in the feature space and by using combination of several
Gaussian functions that has different statistical properties, the best
feature representation can be modelled using probability density
function. The recognition process is performed using maximum
likelihood value computed using pre-calculated GMM components.
The method is tested using FERET datasets and is able to achieved
92% recognition rates.
Abstract: Natural hydrocarbon seepage has helped petroleum
exploration as a direct indicator of gas and/or oil subsurface
accumulations. Surface macro-seeps are generally an indication of a
fault in an active Petroleum Seepage System belonging to a Total
Petroleum System. This paper describes a case study in which
multiple analytical techniques were used to identify and characterize
trace petroleum-related hydrocarbons and other volatile organic
compounds in groundwater samples collected from Sousse aquifer
(Central Tunisia). The analytical techniques used for analyses of
water samples included gas chromatography-mass spectrometry (GCMS),
capillary GC with flame-ionization detection, Compound
Specific Isotope Analysis, Rock Eval Pyrolysis. The objective of the
study was to confirm the presence of gasoline and other petroleum
products or other volatile organic pollutants in those samples in order
to assess the respective implication of each of the potentially
responsible parties to the contamination of the aquifer. In addition,
the degree of contamination at different depths in the aquifer was also
of interest. The oil and gas seeps have been investigated using
biomarker and stable carbon isotope analyses to perform oil-oil and
oil-source rock correlations. The seepage gases are characterized by
high CH4 content, very low δ13CCH4 values (-71,9 ‰) and high
C1/C1–5 ratios (0.95–1.0), light deuterium–hydrogen isotope ratios (-
198 ‰) and light δ13CC2 and δ13CCO2 values (-23,8‰ and-23,8‰
respectively) indicating a thermogenic origin with the contribution of
the biogenic gas. An organic geochemistry study was carried out on
the more ten oil seep samples. This study includes light hydrocarbon
and biomarkers analyses (hopanes, steranes, n-alkanes, acyclic
isoprenoids, and aromatic steroids) using GC and GC-MS. The
studied samples show at least two distinct families, suggesting two
different types of crude oil origins: the first oil seeps appears to be
highly mature, showing evidence of chemical and/or biological
degradation and was derived from a clay-rich source rock deposited
in suboxic conditions. It has been sourced mainly by the lower
Fahdene (Albian) source rocks. The second oil seeps was derived
from a carbonate-rich source rock deposited in anoxic conditions,
well correlated with the Bahloul (Cenomanian-Turonian) source rock.
Abstract: Part and parcel of building green homes (GHs) with
favorable thermal comfort (TC) is to design and build with reduced
carbon footprint (CF) from embodied energy in the building envelope
and reduced operational CF overall. Together, the environmental
impact of GHs can be reduced significantly. Nevertheless, there is
still a need to identify the base CF value for Malaysian GHs and this
can be done by assessing existing ones which can then be compared
to conventional and vernacular houses which are built differently
with different building materials. This paper underlines the research
design and introduces the case studies. For now, the operational CF
of the case studies is beyond the scope of this study. Findings from
this research could identify the best building material and
construction technique combination to build GHs depending on the
available skills, financial constraints and the condition of the
immediate environment.
Abstract: Multi-Level Inverter technology has been developed in the area of high-power medium-voltage energy scheme, because of their advantages such as devices of lower rating can be used thereby enabling the schemes to be used for high voltage applications. Reduced Total Harmonic Distortion (THD).Since the dv/dt is low; the Electromagnetic Interference from the scheme is low. To avoid the switching losses Lower switching frequencies can be used. In this paper present a survey of various topologies, control strategy and modulation techniques used by these inverters. Here the regenerative and superior topologies are also discussed.
Abstract: Chitosan has been an attractive biopolymer for
decades, but its processability is lowered by its poor solubility,
especially in physiological pH values. Freeze concentrated reactions
of chitosan with several organic acids including acrylic, citraconic,
itaconic, and maleic acid revealed improved solubility and
morphological properties. Solubility traits were assessed with a
modified ninhydrin test. Chitosan derivatives were characterized by
ATR-FTIR and morphological characteristics were determined by
SEM. This study is a unique approach to chemically modify chitosan
to enhance water solubility.