Abstract: The effects of flame-holder position, the ratio of flame
holder diameter to combustion chamber diameter and injection angle
on fuel propulsive droplets sizing and effective mass fraction have
been studied by a cold flow. We named the mass of fuel vapor inside
the flammability limit as the effective mass fraction. An empty
cylinder as well as a flame-holder which are a simulator for duct
combustion has been considered. The airflow comes into the cylinder
from one side and injection operation will be done by four nozzles
which are located on the entrance of cylinder. To fulfill the
calculations a modified version of KIVA-3V code which is a
transient, three-dimensional, multiphase, multi component code for
the analysis of chemically reacting flows with sprays, is used.
Abstract: Distillery spentwash contains high chemical oxygen
demand (COD), biological oxygen demand (BOD), color, total
dissolved solids (TDS) and other contaminants even after biological
treatment. The effluent can’t be discharged as such in the surface
water bodies or land without further treatment. Reverse osmosis (RO)
treatment plants have been installed in many of the distilleries at
tertiary level in many of the distilleries in India, but are not properly
working due to fouling problem which is caused by the presence of
high concentration of organic matter and other contaminants in
biologically treated spentwash. In order to make the membrane
treatment a proven and reliable technology, proper pre-treatment is
mandatory. In the present study, ultra-filtration (UF) for pretreatment
of RO at tertiary stage has been performed. Operating
parameters namely initial pH (pHo: 2–10), trans-membrane pressure
(TMP: 4-20 bars) and temperature (T: 15-43°C) were used for
conducting experiments with UF system. Experiments were
optimized at different operating parameters in terms of COD, color,
TDS and TOC removal by using response surface methodology
(RSM) with central composite design. The results showed that
removal of COD, color and TDS was 62%, 93.5% and 75.5%
respectively, with UF, at optimized conditions with increased
permeate flux from 17.5 l/m2/h (RO) to 38 l/m2/h (UF-RO). The
performance of the RO system was greatly improved both in term of
pollutant removal as well as water recovery.
Abstract: Biodiesel production from vegetable oil will produce
glycerol as by-product about 10% of the biodiesel production. The
amount of glycerol that was produced needed alternative way to
handling immediately so as to not become the waste that polluted
environment. One of the solutions was to process glycerol to
polyglycidyl nitrate (PGN). PGN is synthesized from glycerol by
three-step reactions i.e. nitration of glycerol, cyclization of 13-
dinitroglycerine and polymerization of glycosyl nitrate. Optimum
condition of nitration of glycerol with nitric acid has not been known.
Thermodynamic feasibility should be done before run experiments in
the laboratory. The aim of this study was to determine the parameters
those affect nitration of glycerol and nitric acid and chose the
operation condition. Many parameters were simulated to verify its
possibility to experiment under conditions which would get the
highest conversion of 1, 3-dinitroglycerine and which was the ideal
condition to get it. The parameters that need to be studied to obtain
the highest conversion of 1, 3-dinitroglycerine were mol ratio of
nitric acid/glycerol, reaction temperature, mol ratio of
glycerol/dichloromethane and pressure. The highest conversion was
obtained in the range of mol ratio of nitric acid /glycerol between 2/1
– 5/1, reaction temperature of 5-25oC and pressure of 1 atm. The
parameters that need to be studied further to obtain the highest
conversion of 1.3 DNG are mol ratio of nitric acid/glycerol and
reaction temperature.
Abstract: The aim of the present study is to detect the chaotic
behavior in monetary economic relevant dynamical system. The
study employs three different forms of Taylor rules: current, forward,
and backward looking. The result suggests the existence of the
chaotic behavior in all three systems. In addition, the results strongly
represent that using expectations in policy rule especially rational
expectation hypothesis can increase complexity of the system and
leads to more chaotic behavior.
Abstract: This paper investigates the parametric stability of an
axially moving web subjected to non-uniform in-plane edge
excitations on two opposite, simply-supported edges. The web is
modeled as a viscoelastic plate whose constitutive relation obeys the
Kelvin-Voigt model, and the in-plane edge excitations are expressed
as the sum of a static tension and a periodical perturbation. Due to the
in-plane edge excitations, the moving plate may bring about
parametric instability under certain situations. First, the in-plane
stresses of the plate due to the non-uniform edge excitations are
determined by solving the in-plane forced vibration problem. Then,
the dependence on the spatial coordinates in the equation of transverse
motion is eliminated by the generalized Galerkin method, which
results in a set of discretized system equations in time. Finally, the
method of multiple scales is utilized to solve the set of system
equations analytically if the periodical perturbation of the in-plane
edge excitations is much smaller as compared with the static tension of
the plate, from which the stability boundaries of the moving plate are
obtained. Numerical results reveal that only combination resonances
of the summed-type appear under the in-plane edge excitations
considered in this work.
Abstract: Acoustic properties of polymeric liquids are high
sensitive to free gas traces in the form of fine bubbles. Their presence
is typical for such liquids because of chemical reactions, small
wettability of solid boundaries, trapping of air in technological
operations, etc. Liquid temperature influences essentially its
rheological properties, which may have an impact on the bubble
pulsations and sound propagation in the system. The target of the
paper is modeling of the liquid temperature effect on single bubble
dynamics and sound dispersion and attenuation in polymeric solution
with spherical gas bubbles. The basic sources of attenuation (heat
exchange between gas in microbubbles and surrounding liquid,
rheological and acoustic losses) are taken into account. It is supposed
that in the studied temperature range the interface mass transfer has a
minor effect on bubble dynamics. The results of the study indicate
that temperature raise yields enhancement of bubble pulsations and
increase in sound attenuation in the near-resonance range and may
have a strong impact on sound dispersion in the liquid-bubble
mixture at frequencies close to the resonance frequency of bubbles.
Abstract: Background subtraction and temporal difference are
often used for moving object detection in video. Both approaches are
computationally simple and easy to be deployed in real-time image
processing. However, while the background subtraction is highly
sensitive to dynamic background and illumination changes, the
temporal difference approach is poor at extracting relevant pixels of
the moving object and at detecting the stopped or slowly moving
objects in the scene. In this paper, we propose a simple moving object
detection scheme based on adaptive background subtraction and
temporal difference exploiting dynamic background updates. The
proposed technique consists of histogram equalization, a linear
combination of background and temporal difference, followed by the
novel frame-based and pixel-based background updating techniques.
Finally, morphological operations are applied to the output images.
Experimental results show that the proposed algorithm can solve the
drawbacks of both background subtraction and temporal difference
methods and can provide better performance than that of each method.
Abstract: This paper aims to project the construction of a
prototype azimuthal thruster, mounted with materials of low cost and
easy access, testing in a controlled environment to measure their
performance, characteristics and feasibility of future projects. The
construction of the simulation of dynamic positioning software,
responsible for simulating a vessel and reposition it when necessary.
Validation tests were performed in the form of partial or complete
system. These tests validate the system manually or automatically.
The system provides an interface to the user and simulates the
conditions unfavorable positioning of a vessel, accurately calculates
the azimuth angle, the direction of rotation of the helix and the time
that this should be turned on so that the vessel back to position
original. A serial communication connects the Simulation Dynamic
Positioning System with Embedded System causing the usergenerated
data to simulate the DP system arrives in the form of
control signals to the motors of the propellant. This article addresses
issues in the marine industry employees.
Abstract: The purpose of this paper is to present a modeling and
control of a quarter-car active suspension system with unknown
mass, unknown time-delay and road disturbance. The objective of
designing the controller is to derive a control law to achieve stability
of the system and convergence that can considerably improve ride
comfort and road disturbance handling. This is accomplished by
using Routh-Hurwitz criterion based on defined parameters.
Mathematical proof is given to show the ability of the designed
controller to ensure the target of design, implementation with the
active suspension system and enhancement dispersion oscillation of
the system despite these problems. Simulations were also performed
to control quarter car suspension, where the results obtained from
these simulations verify the validity of the proposed design.
Abstract: This paper presents the design and fabrication of a
novel piezoelectric actuator for a gas micro pump with check valve
having the advantages of miniature size, light weight and low power
consumption. The micro pump is designed to have eight major
components, namely a stainless steel upper cover layer, a piezoelectric
actuator, a stainless steel diaphragm, a PDMS chamber layer, two
stainless steel channel layers with two valve seats, a PDMS check
valve layer with two cantilever-type check valves and an acrylic
substrate. A prototype of the gas micro pump, with a size of 52 mm ×
50 mm × 5.0 mm, is fabricated by precise manufacturing. This device
is designed to pump gases with the capability of performing the
self-priming and bubble-tolerant work mode by maximizing the stroke
volume of the membrane as well as the compression ratio via
minimization of the dead volume of the micro pump chamber and
channel. By experiment apparatus setup, we can get the real-time
values of the flow rate of micro pump and the displacement of the
piezoelectric actuator, simultaneously. The gas micro pump obtained
higher output performance under the sinusoidal waveform of 250 Vpp.
The micro pump achieved the maximum pumping rates of 1185
ml/min and back pressure of 7.14 kPa at the corresponding frequency
of 120 and 50 Hz.
Abstract: This study conducts simulation analyses to find the
optimal debt ceiling of Taiwan, while factoring in welfare
maximization under a dynamic stochastic general equilibrium
framework. The simulation is based on Taiwan's 2001 to 2011
economic data and shows that welfare is maximized at a debt/GDP
ratio of 0.2, increases in the debt/GDP ratio leads to increases in both
tax and interest rates and decreases in the consumption ratio and
working hours. The study results indicate that the optimal debt ceiling
of Taiwan is 20% of GDP, where if the debt/GDP ratio is greater than
40%, the welfare will be negative and result in welfare loss.
Abstract: The literature on language teaching and second
language acquisition has been largely driven by monolingual
ideology with a common assumption that a second language (L2) is
best taught and learned in the L2 only. The current study challenges
this assumption by reporting learners' positive perceptions of tertiary
level teachers' code switching practices in Vietnam. The findings of
this study contribute to our understanding of code switching practices
in language classrooms from a learners' perspective.
Data were collected from student participants who were working
towards a Bachelor degree in English within the English for Business
Communication stream through the use of focus group interviews.
The literature has documented that this method of interviewing has a
number of distinct advantages over individual student interviews. For
instance, group interactions generated by focus groups create a more
natural environment than that of an individual interview because they
include a range of communicative processes in which each individual
may influence or be influenced by others - as they are in their real
life. The process of interaction provides the opportunity to obtain the
meanings and answers to a problem that are "socially constructed
rather than individually created" leading to the capture of real-life
data. The distinct feature of group interaction offered by this
technique makes it a powerful means of obtaining deeper and richer
data than those from individual interviews. The data generated
through this study were analysed using a constant comparative
approach. Overall, the students expressed positive views of this
practice indicating that it is a useful teaching strategy. Teacher code
switching was seen as a learning resource and a source supporting
language output. This practice was perceived to promote student
comprehension and to aid the learning of content and target language
knowledge. This practice was also believed to scaffold the students'
language production in different contexts. However, the students
indicated their preference for teacher code switching to be
constrained, as extensive use was believed to negatively impact on
their L2 learning and trigger cognitive reliance on the L1 for L2
learning. The students also perceived that when the L1 was used to a
great extent, their ability to develop as autonomous learners was
negatively impacted.
This study found that teacher code switching was supported in
certain contexts by learners, thus suggesting that there is a need for
the widespread assumption about the monolingual teaching approach
to be re-considered.
Abstract: This work consists of a numerical simulation of
convective heat transfer in a vertical plane channel filled with a heat
generating porous medium, in the absence of local thermal
equilibrium. The walls are maintained to a constant temperature and
the inlet velocity is uniform. The dynamic range is described by the
Darcy-Brinkman model and the thermal field by two energy
equations model. A dimensionless formulation is developed for
performing a parametric study based on certain dimensionless groups
such as, the Biot interstitial number, the thermal conductivity ratio
and the volumetric heat generation, q '''. The governing equations are
solved using the finite volume method, gave rise to a multitude of
results concerning in particular the thermal field in the porous
channel and the existence or not of the local thermal equilibrium.
Abstract: The elastic properties and fracture of two-dimensional
graphene were calculated purely from the atomic bonding (stretching
and bending) based on molecular mechanics method. Considering the
representative unit cell of graphene under various loading conditions,
the deformations of carbon bonds and the variations of the interlayer
distance could be realized numerically under the geometry constraints
and minimum energy assumption. In elastic region, it was found that
graphene was in-plane isotropic. Meanwhile, the in-plane deformation
of the representative unit cell is not uniform along armchair direction
due to the discrete and non-uniform distributions of the atoms. The
fracture of graphene could be predicted using fracture criteria based on
the critical bond length, over which the bond would break. It was
noticed that the fracture behavior were directional dependent, which
was consistent with molecular dynamics simulation results.
Abstract: Cloud computing has emerged as a promising
direction for cost efficient and reliable service delivery across data
communication networks. The dynamic location of service facilities
and the virtualization of hardware and software elements are stressing
the communication networks and protocols, especially when data
centres are interconnected through the internet. Although the
computing aspects of cloud technologies have been largely
investigated, lower attention has been devoted to the networking
services without involving IT operating overhead. Cloud computing
has enabled elastic and transparent access to infrastructure services
without involving IT operating overhead. Virtualization has been a
key enabler for cloud computing. While resource virtualization and
service abstraction have been widely investigated, networking in
cloud remains a difficult puzzle. Even though network has significant
role in facilitating hybrid cloud scenarios, it hasn't received much
attention in research community until recently. We propose Network
as a Service (NaaS), which forms the basis of unifying public and
private clouds. In this paper, we identify various challenges in
adoption of hybrid cloud. We discuss the design and implementation
of a cloud platform.
Abstract: We used live E. coli containing synthetic genetic
oscillators to study how the degree of synchrony between the genetic
circuits of sister cells changes with temperature. We found that both
the mean and the variability of the degree of synchrony between the
fluorescence signals from sister cells are affected by temperature.
Also, while most pairs of sister cells were found to be highly
synchronous in each condition, the number of asynchronous pairs
increased with increasing temperature, which was found to be due to
disruptions in the oscillations. Finally we provide evidence that these
disruptions tend to affect multiple generations as opposed to
individual cells. These findings provide insight in how to design
more robust synthetic circuits and in how cell division can affect their
dynamics.
Abstract: In this paper, the energy saving and human thermal
comfort in a typical office room are investigated. The impact of a
combined system of exhaust inlet air with light slots located at the
ceiling level in a room served by displacement ventilation system is
numerically modelled. Previous experimental data are used to
validate the Computational Fluid Dynamic (CFD) model. A case
study of simulated office room includes two seating occupants, two
computers, two data loggers and four lamps. The combined system is
located at the ceiling level above the heat sources. A new method of
calculation for the cooling coil load in Stratified Air Distribution
(STRAD) system is used in this study. The results show that 47.4%
energy saving of space cooling load can be achieved by combing the
exhaust inlet air with light slots at the ceiling level above the heat
sources.
Abstract: The Chair of Thermal Engineering at Poznan
University of Technology has been conducted research works on the
possibilities of using carbon nanostructures in energy and mechanics
applications for a couple of years. Those studies have provided results in a form of co-operation with foreign research centres, numerous publications and patent
applications.
Authors of this paper have studied the influence of multi-walled
carbon nanostructures on changes in static friction arising when steel
surfaces were moved. Tests were made using the original test stand
consisting of automatically controlled inclined plane driven by
precise stepper motors. Computer program created in the LabView
environment was responsible for monitoring of the stand operation,
accuracy of measurements and archiving the obtained results. Such a
solution enabled to obtain high accuracy and repeatability of all
conducted experiments.
Tests and analysis of the obtained results allowed us to determine
how additional layers of carbon nanostructures influenced on changes
of static friction coefficients. At the same time, we analyzed the
potential possibilities of applying nanostructures under consideration
in mechanics.
Abstract: One of the functions of the commercial heavy vehicle
is to safely and efficiently transport goods and people. Due to its size
and carrying capacity, it is important to study the vehicle dynamic
stability during cornering. Study has shown that there are a number of
overloaded heavy vehicles or permissible Gross Vehicle Weight
(GVW) violations recorded at selected areas in Malaysia assigned by
its type and category. Thus, the objective of this study is to
investigate the correlation and effect of the GVW on heavy vehicle
stability during cornering event using simulation. Various selected
heavy vehicle types and category are simulated using IPG/Truck
Maker® with different GVW and road condition (coefficient of
friction of road surface), while the speed, driver characteristic, center
of gravity of load and road geometry are constant. Based on the
analysis, the relationship between GVW and lateral acceleration were
established. As expected, on the same value of coefficient of friction,
the maximum lateral acceleration would be increased as the GVW
increases.
Abstract: Let us consider that the entire universe is composed of
a single hydrogen atom within which the electron is moving around
the proton. In this case, according to classical theories of physics,
radiation, photons respectively, should be absorbed by the electron.
Depending on the number of photons absorbed, the electron radius of
rotation around the proton is established. Until now, the principle of
photons absorption by electrons and the electron transition to a new
energy level, namely to a higher radius of rotation around the proton,
is not clarified in physics. This paper aims to demonstrate that
radiation, photons respectively, have mass and negative electrostatic
charge similar to electrons but infinitely smaller. The experiments
which demonstrate this theory are simple: thermal expansion,
photoelectric effect and thermonuclear reaction.