Abstract: The effects of the pumping wavelength and their power
on the gain flattening of a fiber Raman amplifier (FRA) are
investigated. The multi-wavelength pumping scheme is utilized to
achieve gain flatness in FRA. It is proposed that gain flatness
becomes better with increase in number of pumping wavelengths
applied. We have achieved flat gain with 0.27 dB fluctuation in a
spectral range of 1475-1600 nm for a Raman fiber length of 10 km by
using six pumps with wavelengths with in the 1385-1495 nm interval.
The effect of multi-wavelength pumping scheme on gain saturation in
FRA is also studied. It is proposed that gain saturation condition gets
improved by using this scheme and this scheme is more useful for
higher spans of Raman fiber length.
Abstract: In this study, out-of-plane free vibrations of a circular
rods is investigated theoretically. The governing equations for
naturally twisted and curved spatial rods are obtained using
Timoshenko beam theory and rewritten for circular rods. Effects of
the axial and shear deformations are considered in the formulations.
Ordinary differential equations in scalar form are solved analytically
by using transfer matrix method. The circular rods of the mass matrix
are obtained by using straight rod of consistent mass matrix. Free
vibrations frequencies obtained by solving eigenvalue problem. A
computer program coded in MATHEMATICA language is prepared.
Circular beams are analyzed through various examples for free
vibrations analysis. Results are compared with ANSYS results based
on finite element method and available in the literature.
Abstract: The following paper presents the results of a study
aimed at achieving a better understanding of the psychological
readiness for mobile learning (m-learning) among Saudi students,
while also evaluating m-learning readiness as a whole in Saudi
Arabia - a topic that has not yet received adequate attention from
researchers. Data was acquired via a questionnaire administered to
131 Saudi students at UK universities, in July 2013. The study
confirmed that students are confident about using mobile devices in
their daily lives, and that they would welcome more opportunities for
mobile learning. The findings also indicated that Saudi higher
education students are very familiar with, and psychologically ready
for, m-learning.
Abstract: 600 schools going adolescents and 100 teachers from
16 schools of Dhemaji and Lakhimpur district of Assam, India were
surveyed to assess and compare their awareness regarding AIDS and
AIDS Education. An awareness test was administered containing 38
items for adolescents and 40 items for teachers in the test.
Observations revealed that the majority of school-going adolescents
are poor in their HIV/AIDS and AIDS education awareness. It shows
that the school going adolescents of Dhemaji district are better in
HIV/AIDS and AIDS education awareness than the school going
adolescents of Lakhimpur district while comparing the gender,
settlement, steam and district wise variables.
Abstract: Image enhancement is a challenging issue in many applications. In the last two decades, there are various filters developed. This paper proposes a novel method which removes Gaussian noise from the gray scale images. The proposed technique is compared with Enhanced Fuzzy Peer Group Filter (EFPGF) for various noise levels. Experimental results proved that the proposed filter achieves better Peak-Signal-to-Noise-Ratio PSNR than the existing techniques. The proposed technique achieves 1.736dB gain in PSNR than the EFPGF technique.
Abstract: In this study, ultrasonic assisted machining (UAM) technique is applied in side-surface milling experiment for glass-ceramic workpiece material. The tungsten carbide cutting-tool with diamond coating is used in conjunction with two kinds of cooling/lubrication mediums such as water-soluble (WS) cutting fluid and minimum quantity lubricant (MQL). Full factorial process parameter combinations on the milling experiments are planned to investigate the effect of process parameters on cutting performance. From the experimental results, it tries to search for the better process parameter combination which the edge-indentation and the surface roughness are acceptable. In the machining experiments, ultrasonic oscillator was used to excite a cutting-tool along the radial direction producing a very small amplitude of vibration frequency of 20KHz to assist the machining process. After processing, toolmaker microscope was used to detect the side-surface morphology, edge-indentation and cutting tool wear under different combination of cutting parameters, and analysis and discussion were also conducted for experimental results. The results show that the main leading parameters to edge-indentation of glass ceramic are cutting depth and feed rate. In order to reduce edge-indentation, it needs to use lower cutting depth and feed rate. Water-soluble cutting fluid provides a better cooling effect in the primary cutting area; it may effectively reduce the edge-indentation and improve the surface morphology of the glass ceramic. The use of ultrasonic assisted technique can effectively enhance the surface finish cleanness and reduce cutting tool wear and edge-indentation.
Abstract: Association rule mining is one of the most important fields of data mining and knowledge discovery. In this paper, we propose an efficient multiple support frequent pattern growth algorithm which we called “MSFP-growth” that enhancing the FPgrowth algorithm by making infrequent child node pruning step with multiple minimum support using maximum constrains. The algorithm is implemented, and it is compared with other common algorithms: Apriori-multiple minimum supports using maximum constraints and FP-growth. The experimental results show that the rule mining from the proposed algorithm are interesting and our algorithm achieved better performance than other algorithms without scarifying the accuracy.
Abstract: The safety and health performances aspects of a building are the most challenging aspect of facility management. It requires a deep understanding by the building managers on the factors that contribute to health and safety performances. This study attempted to develop an explanatory architectural safety performance model for stratified low-cost housing in Malaysia. The proposed Building Safety and Health Performance (BSHP) model was tested empirically through a survey on 308 construction practitioners using partial least squares (PLS) and structural equation modelling (SEM) tool. Statistical analysis results supports the conclusion that architecture, building services, external environment, management approaches and maintenance management have positive influence on safety and health performance of stratified low-cost housing in Malaysia. The findings provide valuable insights for construction industry to introduce BSHP model in the future where the model could be used as a guideline for training purposes of managers and better planning and implementation of building management.
Abstract: In this paper static scheme of under-frequency based load shedding is considered for chemical and petrochemical industries with islanded distribution networks relying heavily on the primary commodity to ensure minimum production loss, plant downtime or critical equipment shutdown. A simplistic methodology is proposed for in-house implementation of this scheme using underfrequency relays and a step by step guide is provided including the techniques to calculate maximum percentage overloads, frequency decay rates, time based frequency response and frequency based time response of the system. Case study of FFL electrical system is utilized, presenting the actual system parameters and employed load shedding settings following the similar series of steps. The arbitrary settings are then verified for worst overload conditions (loss of a generation source in this case) and comprehensive system response is then investigated.
Abstract: A numerical model has been developed to investigate the thermally triggered release kinetics for drug delivery using phase change material as shell of microcapsules. Biocompatible material n-Eicosane is used as demonstration. PCM shell of microcapsule will remain in solid form after the drug is taken, so the drug will be encapsulated by the shell, and will not be released until the target body part of lesion is exposed to external heat source, which will thermally trigger the release kinetics, leading to solid-to-liquid phase change. The findings can lead to better understanding on the key effects influencing the phase change process for drug delivery applications. The facile approach to release drug from core/shell structure of microcapsule can be well integrated with organic solvent free fabrication of microcapsules, using double emulsion as template in microfluidic aqueous two phase system.
Abstract: This work proposes a data-driven multiscale based
quantitative measures to reveal the underlying complexity of
electroencephalogram (EEG), applying to a rodent model of
hypoxic-ischemic brain injury and recovery. Motivated by that real
EEG recording is nonlinear and non-stationary over different
frequencies or scales, there is a need of more suitable approach over
the conventional single scale based tools for analyzing the EEG data.
Here, we present a new framework of complexity measures
considering changing dynamics over multiple oscillatory scales. The
proposed multiscale complexity is obtained by calculating entropies of
the probability distributions of the intrinsic mode functions extracted
by the empirical mode decomposition (EMD) of EEG. To quantify
EEG recording of a rat model of hypoxic-ischemic brain injury
following cardiac arrest, the multiscale version of Tsallis entropy is
examined. To validate the proposed complexity measure, actual EEG
recordings from rats (n=9) experiencing 7 min cardiac arrest followed
by resuscitation were analyzed. Experimental results demonstrate that
the use of the multiscale Tsallis entropy leads to better discrimination
of the injury levels and improved correlations with the neurological
deficit evaluation after 72 hours after cardiac arrest, thus suggesting an
effective metric as a prognostic tool.
Abstract: A cold, thin film of liquid impinging on an isothermal
hot, horizontal surface has been investigated. An approximate
solution for the velocity and temperature distributions in the flow
along the horizontal surface is developed, which exploits the
hydrodynamic similarity solution for thin film flow. The approximate
solution may provide a valuable basis for assessing flow and heat
transfer in more complex settings.
Abstract: Control of honey frauds is needed in Ecuador to
protect bee keepers and consumers because simple syrups and new
syrups with eucalyptus are sold as genuine honeys. Authenticity of
Ecuadorian commercial honeys was tested with a vortex emulsion
consisting on one volume of honey:water (1:1) dilution, and two
volumes of diethyl ether. This method allows a separation of phases
in one minute to discriminate genuine honeys that form three phase
and fake honeys that form two phases; 34 of the 42 honeys analyzed
from five provinces of Ecuador were genuine. This was confirmed
with 1H NMR spectra of honey dilutions in deuterated water with an
enhanced amino acid region with signals for proline, phenylalanine
and tyrosine. Classic quality indicators were also tested with this
method (sugars, HMF), indicators of fermentation (ethanol, acetic
acid), and residues of citric acid used in the syrup manufacture. One
of the honeys gave a false positive for genuine, being an admixture of
genuine honey with added syrup, evident for the high sucrose.
Sensory analysis was the final confirmation to recognize the honey
groups studied here, namely honey produced in combs by Apis
mellifera, fake honey, and honey produced in cerumen pots by
Geotrigona, Melipona, and Scaptotrigona. Chloroform extractions of
honey were also done to search lipophilic additives in NMR spectra.
This is a valuable contribution to protect honey consumers, and to
develop the beekeeping industry in Ecuador.
Abstract: Propylene self-metathesis to ethylene and butene was
studied over WOx/SiO2 catalysts at 450oC and atmospheric pressure.
The WOx/SiO2 catalysts were prepared by incipient wetness
impregnation of ammonium metatungstate aqueous solution. It was
found that, adding nano-sized extra supports (SiO2 and TiO2) by
physical mixing with the WOx/SiO2 enhanced propylene conversion.
The UV-Vis and FT-Raman results revealed that WOx could migrate
from the original silica support to the extra support, leading to a
better dispersion of WOx. The ICP-OES results also indicate that
WOx existed on the extra support. Coke formation was investigated
on the catalysts after 10 h time-on-stream by TPO. However, adding
nano-sized extra supports led to higher coke formation which may be
related to acidity as characterized by NH3-TPD.
Abstract: The quality and condition of perishable products
delivered to the market and their subsequent selling prices are
directly affected by the care taken during harvesting and handling.
Mechanical injury, in fact, occurs at all stages, from pre-harvest
operations through post-harvest handling, packing and transport to
the market. The main implications of this damage are the reduction of
the product’s quality and economical losses related to the shelf life
diminution. For most perishable products, the shelf life is relatively
short and it is typically dictated by microbial growth related to the
application of dynamic and static loads during transportation. This
paper presents the correlation between vibration levels and
microbiological growth on strawberries and woodland strawberries
and detects the presence of volatile organic compounds (VOC) in
order to develop an intelligent logistic unit capable of monitoring
VOCs using a specific sensor system. Fresh fruits were exposed to
vibrations by means of a vibrating table in a temperature-controlled
environment. Microbiological analyses were conducted on samples,
taken at different positions along the column of the crates. The values
obtained were compared with control samples not exposed to
vibrations and the results show that different positions along the
column influence the development of bacteria, yeasts and filamentous
fungi.
Abstract: The material selection in the design of the sandwich
structures is very crucial aspect because of the positive or negative
influences of the base materials to the mechanical properties of the
entire panel. In the literature, it was presented that the selection of the
skin and core materials plays very important role on the behavior of
the sandwich. Beside this, the use of the correct adhesive can make
the whole structure to show better mechanical results and behavior.
In the present work, the static three-point bending tests were
performed on the sandwiches having an aluminum alloy foam core,
the skins made of three different types of fabrics and two different
commercial adhesives (flexible polyurethane and toughened epoxy
based) at different values of support span distances by aiming the
analyses of their flexural performance in terms of absorbed energy,
peak force values and collapse mechanisms. The main results of the
flexural loading are: force-displacement curves obtained after the
bending tests, peak force and absorbed energy values, collapse
mechanisms and adhesion quality. The experimental results presented
that the sandwiches with epoxy based toughened adhesive and the
skins made of S-Glass Woven fabrics indicated the best adhesion
quality and mechanical properties. The sandwiches with toughened
adhesive exhibited higher peak force and energy absorption values
compared to the sandwiches with flexible adhesive. The use of these
sandwich structures can lead to a weight reduction of the transport
vehicles, providing an adequate structural strength under operating
conditions.
Abstract: The main objective of this paper is to provide a new
methodology for road safety assessment in Oman through the
development of suitable accident prediction models. GLM technique
with Poisson or NBR using SAS package was carried out to develop
these models. The paper utilized the accidents data of 31 un-signalized
T-intersections during three years. Five goodness-of-fit
measures were used to assess the overall quality of the developed
models. Two types of models were developed separately; the flow-based
models including only traffic exposure functions, and the full
models containing both exposure functions and other significant
geometry and traffic variables.
The results show that, traffic exposure functions produced much
better fit to the accident data. The most effective geometric variables
were major-road mean speed, minor-road 85th percentile speed,
major-road lane width, distance to the nearest junction, and right-turn
curb radius.
The developed models can be used for intersection treatment or
upgrading and specify the appropriate design parameters of T-intersections.
Finally, the models presented in this thesis reflect the intersection
conditions in Oman and could represent the typical conditions in
several countries in the middle east area, especially gulf countries.
Abstract: Forward Osmosis (FO) polyamide thin-film composite
membranes have been prepared by interfacial polymerization using
commercial UF polyethersulfoneas membrane support. Different
interfacial polymerization times (10s, 30s and 60s) in the organic
solution containing trimesoyl chloride (TMC) at constant m-phenylenediamine
(MPD) concentration (2% w/v) were studied. The
synthesized polyamide membranes then tested for treatment of
natural organic matter (NOM) and compared to commercial Cellulose
TriAcetate (CTA) membrane. It was found that membrane prepared
with higher reaction time (30s and 60s) exhibited better membrane
performance (flux and humic acid removal) over commercial CTA
membrane.
Abstract: The aim of this paper is to present the optimization
methodology developed in the frame of a Coastal Transport
Information System. The system will be used for the effective design
of coastal transportation lines and incorporates subsystems that
implement models, tools and techniques that may support the design
of improved networks. The role of the optimization and decision
subsystem is to provide the user with better and optimal scenarios
that will best fulfill any constrains, goals or requirements posed. The
complexity of the problem and the large number of parameters and
objectives involved led to the adoption of an evolutionary method
(Genetic Algorithms). The problem model and the subsystem
structure are presented in detail, and, its support for simulation is also
discussed.
Abstract: After the internet explosion in the 90’s, technology
was immediately integrated into the school system. Technology
which symbolizes advancement in human knowledge was seen as a
setback by many educators. Efforts have been made to help stem this
erroneous believes and help educators realize the benefits of
technology and ways of implementing it in the classrooms especially
in the sciences. This advancement created a constantly expanding gap
between the pupil’s perception on the use of technology within the
learning atmosphere and the teacher’s perception and limitations
hence, the focus of this paper is on the need to refocus on the use of
Science and Technology in enhancing children’s potentials in
learning at school especially in Science for sustainable development
in Nigeria. The paper recommended measures for facilitating the
sustenance of science and technology in Nigerian schools so as to
enhance the potentials of our children in Science and Technology for
a better tomorrow.