Abstract: Developments in communication technologies
especially in wireless have enabled the progress of low-cost and lowpower
wireless sensor networks (WSNs). The features of such WSN
are holding minimal energy, weak computational capabilities,
wireless communication and an open-medium nature where sensors
are deployed. WSN is underpinned by application driven such as
military applications, the health sector, etc. Due to the intrinsic nature
of the network and application scenario, WSNs are vulnerable to
many attacks externally and internally. In this paper we have focused
on the types of internal attacks of WSNs based on OSI model and
discussed some security requirements, characterizers and challenges
of WSNs, by which to contribute to the WSN-s security research.
Abstract: This paper presents the results of corrosion fatigue
crack growth behaviour of a Ni-Cr-Mn steel commonly used in
marine applications. The effect of mechanical variables such as
frequency and load ratio on fatigue crack growth rate at various
stages has been studied using compact tension (C(T)) specimens
along the rolling direction of steel plate under 3.5% saturated NaCl
aqueous environment. The significance of crack closure on corrosion
fatigue, and the validity of Elber-s empirical linear crack closure
model with the ASTM compliance offset method have been
examined.
Fatigue crack growth rate is higher and threshold stress intensities
are lower in aqueous environment compared to the lab air conditions.
It is also observed that the crack growth rate increases at lower
frequencies. The higher stress ratio promotes the crack growth. The
effect of oxidization and corrosion pit formation is very less as the
stress ratio is increased. It is observed that as stress ratios are
increased, the Elber-s crack closure model agrees well with the crack
closure estimated by the ASTM compliance offset method for tests
conducted at 5Hz frequency compared to tests conducted at 1Hz in
corrosive environment.
Abstract: Where renewable energy sources, solar, hydro, wind are available the remote communities and businesses can be provided with the most reliable and affordable source of electrical energy. This paper presents a model of safari rest contains all the necessary services for the interested tourists who visit the safari Sinai desert. The PV energy system provides the rural energy needs of remote communities. A photovoltaic renewable energy system is designed to feed the global Ac and Dc electrical required load of this safari rest . The benefits of photovoltaic renewable energy at rural applications are its versatility and convenience. This model of safari rest must be taken in consideration by Egyptian Government as it will provide the tourism plane by new interested tourism field which put a big spot on Red sea area: El Ghordaka.
Abstract: Laser engraving is a manufacturing method for those applications where previously Electrical Discharge Machining (EDM) was the only choice. Laser engraving technology removes material layer-by-layer and the thickness of layers is usually in the range of few microns. The aim of the present work is to investigate the influence of the process parameters on the surface quality when machined by laser engraving. The examined parameters were: the pulse frequency, the beam speed and the layer thickness. The surface quality was determined by the surface roughness for every set of parameters. Experimental results on Al7075 material showed that the surface roughness strictly depends on the process parameters used.
Abstract: This paper addresses the problem of recognizing and
interpreting the behavior of human workers in industrial
environments for the purpose of integrating humans in software
controlled manufacturing environments. In this work we propose a
generic concept in order to derive solutions for task-related manual
production applications. Thus, we are able to use a versatile concept
providing flexible components and being less restricted to a specific
problem or application. We instantiate our concept in a spot welding
scenario in which the behavior of a human worker is interpreted
when performing a welding task with a hand welding gun. We
acquire signals from inertial sensors, video cameras and triggers and
recognize atomic actions by using pose data from a marker based
video tracking system and movement data from inertial sensors.
Recognized atomic actions are analyzed on a higher evaluation level
by a finite state machine.
Abstract: The explosion of interest in online gaming and
virtual worlds is leading many universities to investigate
possible educational applications of the new environments.
In this paper we explore the possibilities of 3D online worlds
for teacher education, particularly the field experience
component. Drawing upon two pedagogical examples, we
suggest that virtual simulations may, with certain limitations,
create safe spaces that allow preservice teachers to adopt
alternate identities and interact safely with the “other." In so
doing they may become aware of the constructed nature of
social categories and gain the essential pedagogical skill of
perspective-taking. We suggest that, ultimately, the ability to
be the principal creators of themselves in virtual environments
can increase their ability to do the same in the real world.
Abstract: This paper presents the design of a low power second-order continuous-time sigma-delta modulator for low power
applications. The loop filter of this modulator has been implemented based on the nonlinear transconductance-capacitor (Gm-C) by employing current-mode technique. The nonlinear transconductance uses floating gate MOS (FG-MOS) transistors that operate in weak inversion region. The proposed modulator features low power consumption (
Abstract: Fiber optic sensor technology offers the possibility of
sensing different parameters like strain, temperature, pressure in
harsh environment and remote locations. these kinds of sensors
modulates some features of the light wave in an optical fiber such an
intensity and phase or use optical fiber as a medium for transmitting
the measurement information.
The advantages of fiber optic sensors in contrast to conventional
electrical ones make them popular in different applications and now a
day they consider as a key component in improving industrial
processes, quality control systems, medical diagnostics, and
preventing and controlling general process abnormalities.
This paper is an introduction to fiber optic sensor technology and
some of the applications that make this branch of optic technology,
which is still in its early infancy, an interesting field.
Abstract: With the rapid development of wireless mobile communication, applications for mobile devices must focus on network security. In 2008, Chang-Chang proposed security improvements on the Lu et al.-s elliptic curve authentication key agreement protocol for wireless mobile networks. However, this paper shows that Chang- Chang-s improved protocol is still vulnerable to off-line password guessing attacks unlike their claims.
Abstract: Cements, which are intrinsically brittle materials, can
exhibit a degree of pseudo-ductility when reinforced with a sufficient
volume fraction of a fibrous phase. This class of materials, called
Engineered Cement Composites (ECC) has the potential to be used in
future tunneling applications where a level of pseudo-ductility is
required to avoid brittle failures. However uncertainties remain
regarding mechanical performance. Previous work has focused on
comparatively thin specimens; however for future civil engineering
applications, it is imperative that the behavior in tension of thicker
specimens is understood. In the present work, specimens containing
cement powder and admixtures have been manufactured following
two different processes and tested in tension. Multiple matrix
cracking has been observed during tensile testing, leading to a
“strain-hardening" behavior, confirming the possible suitability of
ECC material when used as thick sections (greater than 50mm) in
tunneling applications.
Abstract: The flow filed around a flatted-roof compound has
been investigated by means of 2D and 3D numerical simulations. A
constant wind velocity profile, based both on the maximum reference
wind speed in the building site (peak gust speed worked out for a 50-
year return period) and on the local roughness coefficient, has been
simulated in order to determine the wind-induced loads on top of the
roof. After determining the influence of the incoming wind directions
on the induced roof loads, a 2D analysis of the most severe load
condition has been performed, achieving a numerical quantification
of the expected wind-induced forces on the PV panels on top of the
roof.
Abstract: There are a many of needs for the development of
SiC-based hydrogen sensor for harsh environment applications. We
fabricated and investigated Pd/Ta2O5/SiC-based hydrogen sensors
with MOS capacitor structure for high temperature process monitoring
and leak detection applications in such automotive, chemical and
petroleum industries as well as direct monitoring of combustion
processes. In this work, we used silicon carbide (SiC) as a substrate to
replace silicon which operating temperatures are limited to below
200°C. Tantalum oxide was investigated as dielectric layer which has
high permeability for hydrogen gas and high dielectric permittivity,
compared with silicon dioxide or silicon nitride. Then, electrical
response properties, such as I-V curve and dependence of capacitance
on hydrogen concentrations were analyzed in the temperature ranges
of room temperature to 500°C for performance evaluation of the
sensor.
Abstract: This paper presents a multiband CPW-fed slot antenna
with L-slot bowtie tuning stub. The proposed antenna has been
designed for PCS 1900, UMTS, WLAN 802.11 a/b/g and bluetooth
applications, with a cost-effective FR4 substrate. The proposed
antenna still radiate as omni-directional in azimuth plane and
sufficient bandwidth for all above mentions. The proposed antenna
works as dual-wideband, bandwidth at low frequency band and high
frequency are about 45.49 % and 22.39 % respectively. The
experimental results of the constructed prototype are presented and
also compared with simulation results using a commercial software
tool.
Abstract: Program slicing is the task of finding all statements in a program that directly or indirectly influence the value of a variable occurrence. The set of statements that can affect the value of a variable at some point in a program is called a program slice. In several software engineering applications, such as program debugging and measuring program cohesion and parallelism, several slices are computed at different program points. In this paper, algorithms are introduced to compute all backward and forward static slices of a computer program by traversing the program representation graph once. The program representation graph used in this paper is called Program Dependence Graph (PDG). We have conducted an experimental comparison study using 25 software modules to show the effectiveness of the introduced algorithm for computing all backward static slices over single-point slicing approaches in computing the parallelism and functional cohesion of program modules. The effectiveness of the algorithm is measured in terms of time execution and number of traversed PDG edges. The comparison study results indicate that using the introduced algorithm considerably saves the slicing time and effort required to measure module parallelism and functional cohesion.
Abstract: There are various kinds of medical equipment which
requires relatively accurate positional adjustments for successful
treatment. However, patients tend to move without notice during a
certain span of operations. Therefore, it is common practice that
accompanying operators adjust the focus of the equipment. In this
paper, tracking controllers for medical equipment are suggested to
replace the operators. The tracking controllers use AHRS sensor
information to recognize the movements of patients. Sensor fusion is
applied to reducing the error magnitudes through linear Kalman filters.
The image processing of optical markers is included to adjust the
accumulation errors of gyroscope sensor data especially for yaw
angles.
The tracking controller reduces the positional errors between the
current focus of a device and the target position on the body of a
patient. Since the sensing frequencies of AHRS sensors are very high
compared to the physical movements, the control performance is
satisfactory. The typical applications are, for example, ESWT or
rTMS, which have the error ranges of a few centimeters.
Abstract: With the advent of emerging personal computing paradigms such as ubiquitous and mobile computing, Web contents are becoming accessible from a wide range of mobile devices. Since these devices do not have the same rendering capabilities, Web contents need to be adapted for transparent access from a variety of client agents. Such content adaptation results in better rendering and faster delivery to the client device. Nevertheless, Web content adaptation sets new challenges for semantic markup. This paper presents an advanced components platform, called MorfeoSMC, enabling the development of mobility applications and services according to a channel model based on Services Oriented Architecture (SOA) principles. It then goes on to describe the potential for integration with the Semantic Web through a novel framework of external semantic annotation of mobile Web contents. The role of semantic annotation in this framework is to describe the contents of individual documents themselves, assuring the preservation of the semantics during the process of adapting content rendering, as well as to exploit these semantic annotations in a novel user profile-aware content adaptation process. Semantic Web content adaptation is a way of adding value to and facilitates repurposing of Web contents (enhanced browsing, Web Services location and access, etc).
Abstract: Computer-mediated communication technologies which provide for virtual communities have typically evolved in a cross-dichotomous manner, such that technical constructs of the technology have evolved independently from the social environment of the community. The present paper analyses some limitations of current implementations of computer-mediated communication technology that are implied by such a dichotomy, and discusses their inhibiting effects on possible developments of virtual communities. A Socio-Technical Indicator Model is introduced that utilizes integrated feedback to describe, simulate and operationalise increasing representativeness within a variety of structurally and parametrically diverse systems. In illustration, applications of the model are briefly described for financial markets and for eco-systems. A detailed application is then provided to resolve the aforementioned technical limitations of moderation on the evolution of virtual communities. The application parameterises virtual communities to function as self-transforming social-technical systems which are sensitive to emergent and shifting community values as products of on-going communications within the collective.
Abstract: This research seeks to investigate the frequency and
profitability of index arbitrage opportunities involving the SET50
futures, SET50 component stocks, and the ThaiDEX SET50 ETF
(ticker symbol: TDEX). In particular, the frequency and profit of
arbitrage are measured in the following three arbitrage tests: (1)
SET50 futures vs. ThaiDEX SET50 ETF, (2) SET50 futures vs.
SET50 component stocks, and (3) ThaiDEX SET50 ETF vs. SET50
component stocks are investigated. For tests (2) and (3), the problems
involve conic optimization and quadratic programming as subproblems.
This research is first to apply conic optimization and
quadratic programming techniques in the context of index arbitrage
and is first to investigate such index arbitrage in the Thai equity and
derivatives markets. Thus, the contribution of this study is twofold.
First, its results would help understand the contribution of the
derivatives securities to the efficiency of the Thai markets. Second,
the methodology employed in this study can be applied to other
geographical markets, with minor adjustments.
Abstract: In the last years numerous applications of Human-
Computer Interaction have exploited the capabilities of Time-of-
Flight cameras for achieving more and more comfortable and precise
interactions. In particular, gesture recognition is one of the most active
fields. This work presents a new method for interacting with a virtual
object in a 3D space. Our approach is based on the fusion of depth
data, supplied by a ToF camera, with color information, supplied
by a HD webcam. The hand detection procedure does not require
any learning phase and is able to concurrently manage gestures of
two hands. The system is robust to the presence in the scene of
other objects or people, thanks to the use of the Kalman filter for
maintaining the tracking of the hands.
Abstract: Electromagnetic flowmeters with DC excitation are used for a wide range of fluid measurement tasks, but are rarely found in dosing applications with short measurement cycles due to the achievable accuracy. This paper will identify a number of factors that influence the accuracy of this sensor type when used for short-term measurements. Based on these results a new signal-processing algorithm will be described that overcomes the identified problems to some extend. This new method allows principally a higher accuracy of electromagnetic flowmeters with DC excitation than traditional methods.