Abstract: In this paper a novel high output impedance, low input impedance, wide bandwidth, very simple current mirror with input and output voltage requirements less than that of a simple current mirror is presented. These features are achieved with very simple structure avoiding extra large node impedances to ensure high bandwidth operation. The circuit's principle of operation is discussed and compared to simple and low voltage cascode (LVC) current mirrors. Such outstanding features of this current mirror as high output impedance ~384K, low input impedance~6.4, wide bandwidth~178MHz, low input voltage ~ 362mV, low output voltage ~ 38mV and low current transfer error ~4% (all at 50μA) makes it an outstanding choice for high performance applications. Simulation results in BSIM 0.35μm CMOS technology with HSPICE are given in comparison with simple, and LVC current mirrors to verify and validate the performance of the proposed current mirror.
Abstract: Offset Double-Disk Opener (DDO) is a popular
furrow opener in conservation tillage. It has some limitations such as
negative suction to penetrate in the soil, hair pinning and mixing seed
and fertilizer in the slot. Because of importance of separation of seed
and fertilizer in the slot, by adding two horizontal mini disks to DDO
a modified opener was made (MDO) which placed the fertilizer
between and under two rows of seed. To consider performance of
novel opener an indoor comparison test between DDO and MDO was
performed at soil bin. The experiment was conducted with three
working speeds (3, 6 and 8 km h-1), two bulk densities of soil (1.1
and 1.4 Mg m-3) and two levels of residues (1 and 2 ton ha-1). The
experimental design consisted in a (3×2×2) complete randomized
factorial with three replicates for each test. Moisture of seed furrow,
separation of seed and fertilizer, hair pinning and resultant forces
acting on the openers were used as assessing indexes. There was no
significant difference between soil moisture content in slots created
by DDO and MDO at 0-4 cm depth, but at 4-8 cm the in the slot
created by MDO moisture content was higher about 9%. Horizontal
force for both openers increased with increasing speed and soil bulk
density. Vertical force for DDO was negative so it needed additional
weight for penetrating in the soil, but vertical force for MDO was
positive and, which can solve the challenge of penetration in the soil
in DDO. In soft soil with heavy residues some trash was pushed by
DDO into seed furrow (hair pinning) but at MDO seed were placed at
clean groove. Lateral and vertical separation of seed and fertilizer
was performed effectively by MDO (4.5 and 5 cm, respectively)
while DDO put seed and fertilizer close to each other. Overall, the
Modified Offset Double-disks (MDO) had better performance. So by
adapting this opener with no-tillage drillers it would possible to have
higher yield in conservation tillage where the most appropriate
opener is disk type.
Abstract: Domain-specific languages describe specific solutions to problems in the application domain. Traditionally they form a solution composing black-box abstractions together. This, usually, involves non-deep transformations over the target model. In this paper we argue that it is potentially powerful to operate with grey-box abstractions to build a domain-specific software system. We present parametric code templates as grey-box abstractions and conceptual tools to encapsulate and manipulate these templates. Manipulations introduce template-s merging routines and can be defined in a generic way. This involves reasoning mechanisms at the code templates level. We introduce the concept of Neurath Modelling Language (NML) that operates with parametric code templates and specifies a visualisation mapping mechanism for target models. Finally we provide an example of calculating a domain-specific software system with predefined NML elements.
Abstract: Anti-allergic effects of royal jelly were evaluated in a human-like mouse model of atopic dermatitis. NC/Nga mice were cutaneously applied with royal jelly for 6 weeks. Royal jelly-treated mice exhibited lower levels of serum total immunoglobulin E in comparison with controls. We found that the treatment decreased (11% to the control) expression of mRNA for aquaporin-3, which is involved in the modulation of epidermal hydration. Microarray analysis revealed more than 10-fold changes in the expression of several genes, such as transglutaminase 2, repetin, and keratins. In normal human epidermal keratinocytes, royal jelly extract suppressed interleukin-8 elevation induced by TNF-α and interferon-γ, suggesting direct anti-inflammatory activity in keratinocytes. Collectively, topical application of royal jelly may be useful for amelioration of lesions and inflammation in atopic dermatitis.
Abstract: Expert systems are used extensively in many domains.
This paper discusses the use of medical expert systems in Pakistan.
Countries all over the world pay special attention on health facilities.
A country like Pakistan faces a lot of trouble in health sector.
Several attempts have been made in Pakistan to improve the health
conditions of the people but the situation is still not encouraging.
There is a shortage of doctors and other trained personnel in
Pakistan. Expert systems can play a vital role in such cases where the
medical expert is not readily available. The purpose of this paper is
to analyze the role that such systems can play in improving the health
conditions of the people in Pakistan.
Abstract: A simple microstructure optical fiber design based on an octagonal cladding structure is presented for simultaneously controlling dispersion and leakage properties. The finite difference method with anisotropic perfectly matched boundary layer is used to investigate the guiding properties. It is demonstrated that octagonal photonic crystal fibers with four rings can assume negative ultra-flattened dispersion of -19 + 0.23 ps/nm/km in the wavelength range of 1.275 μm to 1.68 μm, nearly zero ultra-flattened dispersion of 0 ± 0.40 ps/nm/km in a 1.38 to 1.64 μm, and low confinement losses less than 10-3 dB/km in the entire band of interest.
Abstract: According to the European laws, there is the
possibility of reusing the washing wastes for the environmental
requalification of quarry lakes. The paper deals with the
hydrogeological aspects involved in this possibility, as the
introduction of finest wastes in the quarry lakes can generate
alterations of the hydrogeological setting of the area, and problems
for the future accessibility of the zone. To evaluate the
hydrogeological compatibility of the washing wastes reuse in quarry
lakes a groundwater numerical model was carried out, pointing out
both the hydrogeological feasibility of this intervention and some
guide lines for its optimization, in terms of inflow point with regard
the groundwater flow direction and loss of volume in the quarry lake.
Abstract: An ordered porous antimony-doped tin oxide (ATO) film was successfully prepared using a simple coating process with colloidal templates. The facile production was effective when a combination of 16-nm ATO (as a model of an inorganic nanoparticle) and polystyrene (PS) spheres (as a model of the template) weresimply coated to produce a composite ATO/PS film. Heat treatment was then used to remove the PS and produce the porous film. The porous film with a spherical pore shape and a highly ordered porous structure could be obtained. A potential way for the control of pore size could be also achieved by changing initial template size. The theoretical explanation and mechanism of porous formation were also added, which would be important for the scaling-up prediction and estimation.
Abstract: This paper discusses the investigation of a wearable
textile monopole antenna on specific absorption rate (SAR) for bodycentric
wireless communication applications at 2.45 GHz. The
antenna is characterized on a realistic 8 x 8 x 8 mm3 resolution
truncated Hugo body model in CST Microwave Studio software. The
result exhibited that the simulated SAR values were reduced
significantly by 83.5% as the position of textile monopole was
varying between 0 mm and 15 mm away from the human upper arm.
A power absorption reduction of 52.2% was also noticed as the
distance of textile monopole increased.
Abstract: Although, all high school students in Japan are required to learn informatics, many of them do not learn this topic sufficiently. In response to this situation, we propose a support package for high school informatics classes. To examine what students learned and if they sufficiently understood the context of the lessons, a questionnaire survey was distributed to 186 students. We analyzed the results of the questionnaire and determined the weakest units, which were “basic computer configuration” and “memory and secondary storage”. We then developed a package for teaching these units. We propose that our package be applied in high school classrooms.
Abstract: This paper represents the results of long term strength of mortar incorporating Rice Husk Ash (RHA). For these work mortar samples were made according to ASTM standard C 109/C. OPC cement was partially replaced by RHA at 0, 10, 15, 20, 25 and 30 percent replacement level. After casting all samples were kept in controlled environment and curing was done up to 90 days. Test of mortar was performed on 3, 7, 28, 90, 365 and 700 days. It is noticed that OPC mortar shows better strength at early age than mortar having RHA but at 90 days and onward the picture is different. At 700 days it is observed that mortar containing 20% RHA shows better result than any other samples.
Abstract: The predictability of masonry arch bridges and their
behaviour is widely considered doubtful due to the lack of knowledge
about the conditions of a given masonry arch bridge. The assessment
methods for masonry arch bridges are MEXE, ARCHIE, RING and
Frame Analysis Method. The material properties of the masonry and
fill material are extremely difficult to determine accurately.
Consequently, it is necessary to examine the effect of load dispersal
angle through the fill material, the effect of variations in the stiffness
of the masonry, the tensile strength of the masonry mortar continuum
and the compressive strength of the masonry mortar continuum. It is
also important to understand the effect of fill material on load
dispersal angle to determine their influence on ratings. In this paper a
series of parametric studies, to examine the sensitivity of assessment
ratings to the various sets of input data required by the frame analysis
method, are carried out.
Abstract: Coal fly ash (CFA) generated by coal-based thermal
power plants is mainly composed of some oxides having high
crystallinity, like quartz and mullite. In this study, the effect of CFA
crystallinity toward lead adsorption capacity was investigated. To get
solid with various crystallinity, the solution of sodium hydroxide
(NaOH) of 1-7 M was used to treat CFA at various temperature and
reflux time. Furthermore, to evaluate the effect of NaOH-treated CFA
with respect to adsorption capacity, the treated CFA were examine as
adsorbent for removing lead in the solution. The result shows that
using NaOH to treat CFA causes crystallinity of quartz and mullite
decrease. At higher NaOH concentration (>3M), in addition the
damage of quartz and mullite crystallinity is followed by crystal
formation called hydroxysodalite. The lower crystalllinity, the higher
adsorption capacity.
Abstract: Normally business changes are made in order to
change a level of activity in some way, whether it is sales, cash flow,
productivity, or product portfolio. When attempts are made to make
such changes, too often the business reverts to the old levels of
activity as soon as management attention is diverted. Risk
management is a field of growing interest to project managers as well
as in general business and organizational management. There are
several approaches used to manage risk in projects and this paper is a
brief outline of some that you might encounter, with an indication of
their strengths and weaknesses.
Abstract: Fuller’s earth is a fine-grained, naturally occurring substance that has a substantial ability to adsorb impurities. In the present study Fuller’s earth has been characterized and used for the removal of Pb(II) from aqueous solution. The effect of various physicochemical parameters such as pH, adsorbent dosage and shaking time on adsorption were studied. The result of the equilibrium studies showed that the solution pH was the key factor affecting the adsorption. The optimum pH for adsorption was 5. Kinetics data for the adsorption of Pb(II) was best described by pseudo-second order model. The effective diffusion co-efficient for Pb(II) adsorption was of the order of 10-8 m2/s. The adsorption data for metal adsorption can be well described by Langmuir adsorption isotherm. The maximum uptake of metal was 103.3 mg/g of adsorbent. Mass transfer analysis was also carried out for the adsorption process. The values of mass transfer coefficients obtained from the study indicate that the velocity of the adsorbate transport from bulk to the solid phase was quite fast. The mean sorption energy calculated from Dubinin-Radushkevich isotherm indicated that the metal adsorption process was chemical in nature.
Abstract: Multi criteria decision making (MCDM) methods like analytic hierarchy process, ELECTRE and multi-attribute utility theory are critically studied. They have irregularities in terms of the reliability of ranking of the best alternatives. The Routing Decision Support (RDS) algorithm is trying to improve some of their deficiencies. This paper gives a mathematical verification that the RDS algorithm conforms to the test criteria for an effective MCDM method when a linear preference function is considered.
Abstract: This paper discusses aspects of re-design of loadshedding
schemes with respect to actual developments in the Kosovo
power system. Load-shedding is a type of emergency control that is
designed to ensure system stability by reducing power system load to
match the power generation supply. This paper presents a new
adaptive load-shedding scheme that provides emergency protection
against excess frequency decline, in cases when the Kosovo power
system might be disconnected from the regional transmission
network. The proposed load-shedding scheme uses the local
frequency rate information to adapt the load-shedding pattern to suit
the size and location of the occurring disturbance. The proposed
scheme is tested in a software simulation on a large scale PSS/E
model which represents nine power system areas of Southeast Europe
including the Kosovo power system.
Abstract: Periphyton development and composition were
studied in three different treatments: (i) two fishpond units of
wetland-type wastewater treatment pond systems, (ii) two fishponds
in combined intensive-extensive fish farming systems and (iii) three
traditional polyculture fishponds. Results showed that amounts of
periphyton developed in traditional polyculture fishponds (iii) were
different compared to the other treatments (i and ii), where the main
function of ponds was stated wastewater treatment. Negative
correlation was also observable between water quality parameters
and periphyton production. The lower trophity, halobity and
saprobity level of ponds indicated higher amount of periphyton. The
dry matter content of periphyton was significantly higher in the
samples, which were developed in traditional polyculture fishponds
(2.84±3.02 g m-2 day-1, whereby the ash content in dry matter 74%),
than samples taken from (i) (1.60±2.32 g m-2 day-1, 61%) and (ii)
fishponds (0.65±0.45 g m-2 day-1, 81%).
Abstract: In this paper, a comparative study of application of
supervised and unsupervised learning algorithms on illumination
invariant face recognition has been carried out. The supervised
learning has been carried out with the help of using a bi-layered
artificial neural network having one input, two hidden and one output
layer. The gradient descent with momentum and adaptive learning
rate back propagation learning algorithm has been used to implement
the supervised learning in a way that both the inputs and
corresponding outputs are provided at the time of training the
network, thus here is an inherent clustering and optimized learning of
weights which provide us with efficient results.. The unsupervised
learning has been implemented with the help of a modified
Counterpropagation network. The Counterpropagation network
involves the process of clustering followed by application of Outstar
rule to obtain the recognized face. The face recognition system has
been developed for recognizing faces which have varying
illumination intensities, where the database images vary in lighting
with respect to angle of illumination with horizontal and vertical
planes. The supervised and unsupervised learning algorithms have
been implemented and have been tested exhaustively, with and
without application of histogram equalization to get efficient results.
Abstract: A new numerical method for simultaneously updating mass and stiffness matrices based on incomplete modal measured data is presented. By using the Kronecker product, all the variables that are to be modified can be found out and then can be updated directly. The optimal approximation mass matrix and stiffness matrix which satisfy the required eigenvalue equation and orthogonality condition are found under the Frobenius norm sense. The physical configuration of the analytical model is preserved and the updated model will exactly reproduce the modal measured data. The numerical example seems to indicate that the method is quite accurate and efficient.