Abstract: Radio wave propagation on the road surface is a major
problem on wireless sensor network for traffic monitoring. In this
paper, we compare receiving signal strength on two scenarios 1) an
empty road and 2) a road with a vehicle. We investigate the effect of
antenna polarization and antenna height to the receiving signal
strength. The transmitting antenna is installed on the road surface.
The receiving signal is measured 360 degrees around the transmitting
antenna with the radius of 2.5 meters. Measurement results show the
receiving signal fluctuation around the transmitting antenna in both
scenarios. Receiving signal with vertical polarization antenna results
in higher signal strength than horizontal polarization antenna. The
optimum antenna elevation is 1 meter for both horizon and vertical
polarizations with the vehicle on the road. In the empty road, the
receiving signal level is unvarying with the elevation when the
elevation is greater than 1.5 meters.
Abstract: This paper considers the control of the longitudinal
flight dynamics of an F-16 aircraft. The primary design objective
is model-following of the pitch rate q, which is the preferred
system for aircraft approach and landing. Regulation of the aircraft
velocity V (or the Mach-hold autopilot) is also considered, but
as a secondary objective. The problem is challenging because the
system is nonlinear, and also non-affine in the input. A sliding
mode controller is designed for the pitch rate, that exploits the
modal decomposition of the linearized dynamics into its short-period
and phugoid approximations. The inherent robustness of the SMC
design provides a convenient way to design controllers without gain
scheduling, with a steady-state response that is comparable to that
of a conventional polynomial based gain-scheduled approach with
integral control, but with improved transient performance. Integral
action is introduced in the sliding mode design using the recently
developed technique of “conditional integrators", and it is shown that
robust regulation is achieved with asymptotically constant exogenous
signals, without degrading the transient response. Through extensive
simulation on the nonlinear multiple-input multiple-output (MIMO)
longitudinal model of the F-16 aircraft, it is shown that the conditional
integrator design outperforms the one based on the conventional linear
control, without requiring any scheduling.
Abstract: Missing data is a persistent problem in almost all
areas of empirical research. The missing data must be treated very
carefully, as data plays a fundamental role in every analysis.
Improper treatment can distort the analysis or generate biased results.
In this paper, we compare and contrast various imputation techniques
on missing data sets and make an empirical evaluation of these
methods so as to construct quality software models. Our empirical
study is based on NASA-s two public dataset. KC4 and KC1. The
actual data sets of 125 cases and 2107 cases respectively, without
any missing values were considered. The data set is used to create
Missing at Random (MAR) data Listwise Deletion(LD), Mean
Substitution(MS), Interpolation, Regression with an error term and
Expectation-Maximization (EM) approaches were used to compare
the effects of the various techniques.
Abstract: As computer network technology becomes
increasingly complex, it becomes necessary to place greater
requirements on the validity of developing standards and the
resulting technology. Communication networks are based on large
amounts of protocols. The validity of these protocols have to be
proved either individually or in an integral fashion. One strategy for
achieving this is to apply the growing field of formal methods.
Formal methods research defines systems in high order logic so that
automated reasoning can be applied for verification. In this research
we represent and implement a formerly announced multicast protocol
in Prolog language so that certain properties of the protocol can be
verified. It is shown that by using this approach some minor faults in
the protocol were found and repaired. Describing the protocol as
facts and rules also have other benefits i.e. leads to a process-able
knowledge. This knowledge can be transferred as ontology between
systems in KQML format. Since the Prolog language can increase its
knowledge base every time, this method can also be used to learn an
intelligent network.
Abstract: In this work, we present an automatic vehicle detection
system for airborne videos using combined features. We propose a
pixel-wise classification method for vehicle detection using Dynamic
Bayesian Networks. In spite of performing pixel-wise classification,
relations among neighboring pixels in a region are preserved in the
feature extraction process. The main novelty of the detection scheme is
that the extracted combined features comprise not only pixel-level
information but also region-level information. Afterwards, tracking is
performed on the detected vehicles. Tracking is performed using
efficient Kalman filter with dynamic particle sampling. Experiments
were conducted on a wide variety of airborne videos. We do not
assume prior information of camera heights, orientation, and target
object sizes in the proposed framework. The results demonstrate
flexibility and good generalization abilities of the proposed method on
a challenging dataset.
Abstract: ZnO nanostructures including nanowires, nanorods,
and nanoneedles were successfully deposited on GaAs substrates,
respectively, by simple two-step chemical method for the first time. A
ZnO seed layer was firstly pre-coated on the O2-plasma treated
substrate by sol-gel process, followed by the nucleation of ZnO
nanostructures through hydrothermal synthesis. Nanostructures with
different average diameter (15-250 nm), length (0.9-1.8 μm), density
(0.9-16×109 cm-2) were obtained via adjusting the growth time and
concentration of precursors. From the reflectivity spectra, we
concluded ordered and taper nanostructures were preferential for
photovoltaic applications. ZnO nanoneedles with an average diameter
of 106 nm, a moderate length of 2.4 μm, and the density of 7.2×109
cm-2 could be synthesized in the concentration of 0.04 M for 18 h.
Integrated with the nanoneedle array, the power conversion efficiency
of single junction solar cell was increased from 7.3 to 12.2%,
corresponding to a 67% improvement.
Abstract: Nanocrystalline thin film of Na0.1V2O5.nH2O xerogel
obtained by sol gel synthesis was used as gas sensor. Gas sensing
properties of different gases such as hydrogen, petroleum and
humidity were investigated. Applying XRD and TEM the size of the
nanocrystals is found to be 7.5 nm. SEM shows a highly porous
structure with submicron meter-sized voids present throughout the
sample. FTIR measurement shows different chemical groups
identifying the obtained series of gels. The sample was n-type
semiconductor according to the thermoelectric power and electrical
conductivity. It can be seen that the sensor response curves from
130oC to 150oC show a rapid increase in sensitivity for all types of
gas injection, low response values for heating period and the rapid
high response values for cooling period. This result may suggest that
this material is able to act as gas sensor during the heating and
cooling process.
Abstract: This paper describes the development of a 16-ports optical code division multiple access (OCDMA) encoder prototype based on Arrayed Waveguide Grating (AWG) and optical switches. It is potentially to provide a high security for data transmission due to all data will be transmitted in binary code form. The output signals from AWG are coded with a binary code that given to an optical switch before it signal modulate with the carrier and transmitted to the receiver. The 16-ports encoder used 16 double pole double throw (DPDT) toggle switches to control the polarization of voltage source from +5 V to -5 V for 16 optical switches. When +5 V is given, the optical switch will give code '1' and vice versa. The experimental results showed the insertion loss, crosstalk, uniformity, and optical signal-noise-ratio (OSNR) for the developed prototype are
Abstract: A method is presented for using thermo-mechanical fatigue analysis as a tool in the design of automotive heat exchangers. Use of infra-red thermography to measure the real thermal history in the heat exchanger reduces the time necessary for calculating design parameters and improves prediction accuracy. Thermal shocks are the primary cause of heat exchanger damage. Thermo-mechanical simulation is based on the mean behavior of the aluminum tubes used in the heat exchanger. An energetic fatigue criterion is used to detect critical zones.
Abstract: The nature, prevalence, cellular composition of
leukocyte infiltrates and immunohistochemical characteristics of
their constituent cells in the liver of patients with chronic viral
hepatitis B and C were investigated. It was found that the area of
distribution and cellular composition of infiltrates depended on the
virus type and process activity. The expediency of
immunohistochemical study using leukocyte infiltrates from liver
biopsies of patients with viral hepatitis aimed at clarifying diagnosis,
making prognosis, and choice of optimal treatment with elements of
immune correction is emphasized.
Abstract: Because support interference corrections are not properly
understood, engineers mostly rely on expensive dummy measurements
or CFD calculations. This paper presents a method based on uncorrected wind tunnel measurements and fast calculation techniques
(it is a hybrid method) to calculate wall interference, support interference and residual interference (when e.g. a support member
closely approaches the wind tunnel walls) for any type of wind tunnel and support configuration. The method provides with a simple formula
for the calculation of the interference gradient. This gradient is
based on the uncorrected measurements and a successive calculation
of the slopes of the interference-free aerodynamic coefficients. For the latter purpose a new vortex-lattice routine is developed that corrects
the slopes for viscous effects. A test case of a measurement on a wing proves the value of this hybrid method as trends and orders of
magnitudes of the interference are correctly determined.
Abstract: The study on the tree growth for four species groups of commercial timber in Koh Kong province, Cambodia-s tropical rainforest is described. The simulation for these four groups had been successfully developed in the 5-year interval through year-60. Data were obtained from twenty permanent sample plots in the duration of thirteen years. The aim for this study was to develop stand table simulation system of tree growth by the species group. There were five steps involved in the development of the tree growth simulation: aggregate the tree species into meaningful groups by using cluster analysis; allocate the trees in the diameter classes by the species group; observe the diameter movement of the species group. The diameter growth rate, mortality rate and recruitment rate were calculated by using some mathematical formula. Simulation equation had been created by combining those parameters. Result showed the dissimilarity of the diameter growth among species groups.
Abstract: Campus sustainability is the goal of a university striving for sustainable development. This study found that of 17 popular approaches, two comprehensive campus sustainability assessment frameworks were developed in the context of Sustainability in Higher Education (SHE), and used by many university campuses around the world. Sustainability Tracking Assessment and Rating Systems (STARS) and the Campus Sustainability Assessment Framework (CSAF) approaches are more comprehensive than others. Therefore, the researchers examined aspects and elements used by CSAF and STARS in the approach to develop a campus sustainability assessment framework for Universiti Kebangsaan Malaysia (UKM). Documents analysis found that CSAF and STARS do not focus on physical development, especially the construction industry, as key elements of campus sustainability assessment. This finding is in accordance with the Sustainable UKM Programme which consists of three main components of sustainable community, ecosystem and physical development.
Abstract: Present wireless communication demands compact and intelligent devices with multitasking capabilities at affordable cost. The focus in the presented paper is on a dual band antenna for wireless communication with the capability of operating at two frequency bands with same structure. Two resonance frequencies are observed with the second operation band at 4.2GHz approximately three times the first resonance frequency at 1.5GHz. Structure is simple loop of microstrip line with characteristic impedance 50 ohms. The proposed antenna is designed using defective ground structure (DGS) and shows the nearly one third reductions in size as compared to without DGS. This antenna was simulated on electromagnetic (EM) simulation software and fabricated using microwave integrated circuit technique on RT-Duroid dielectric substrate (εr= 2.22) of thickness (H=15 mils). The designed antenna was tested on automatic network analyzer and shows the good agreement with simulated results. The proposed structure is modeled into an equivalent electrical circuit and simulated on circuit simulator. Subsequently, theoretical analysis was carried out and simulated. The simulated, measured, equivalent circuit response, and theoretical results shows good resemblance. The bands of operation draw many potential applications in today’s wireless communication.
Abstract: In biological and biomedical research motif finding tools are important in locating regulatory elements in DNA sequences. There are many such motif finding tools available, which often yield position weight matrices and significance indicators. These indicators, p-values and E-values, describe the likelihood that a motif alignment is generated by the background process, and the expected number of occurrences of the motif in the data set, respectively. The various tools often estimate these indicators differently, making them not directly comparable. One approach for comparing motifs from different tools, is computing the E-value as the product of the p-value and the number of possible alignments in the data set. In this paper we explore the combinatorics of the motif alignment models OOPS, ZOOPS, and ANR, and propose a generic algorithm for computing the number of possible combinations accurately. We also show that using the wrong alignment model can give E-values that significantly diverge from their true values.
Abstract: Avoiding learning failures in mathematics e-learning environments caused by emotional problems in students with autism has become an important topic for combining of special education with information and communications technology. This study presents an adaptive emotional adjustment model in mathematics e-learning for students with autism, emphasizing the lack of emotional perception in mathematics e-learning systems. In addition, an emotion classification for students with autism was developed by inducing emotions in mathematical learning environments to record changes in the physiological signals and facial expressions of students. Using these methods, 58 emotional features were obtained. These features were then processed using one-way ANOVA and information gain (IG). After reducing the feature dimension, methods of support vector machines (SVM), k-nearest neighbors (KNN), and classification and regression trees (CART) were used to classify four emotional categories: baseline, happy, angry, and anxious. After testing and comparisons, in a situation without feature selection, the accuracy rate of the SVM classification can reach as high as 79.3-%. After using IG to reduce the feature dimension, with only 28 features remaining, SVM still has a classification accuracy of 78.2-%. The results of this research could enhance the effectiveness of eLearning in special education.
Abstract: A gene network gives the knowledge of the regulatory
relationships among the genes. Each gene has its activators and
inhibitors that regulate its expression positively and negatively
respectively. Genes themselves are believed to act as activators and
inhibitors of other genes. They can even activate one set of genes and
inhibit another set. Identifying gene networks is one of the most
crucial and challenging problems in Bioinformatics. Most work done
so far either assumes that there is no time delay in gene regulation or
there is a constant time delay. We here propose a Dynamic Time-
Lagged Correlation Based Method (DTCBM) to learn the gene
networks, which uses time-lagged correlation to find the potential
gene interactions, and then uses a post-processing stage to remove
false gene interactions to common parents, and finally uses dynamic
correlation thresholds for each gene to construct the gene network.
DTCBM finds correlation between gene expression signals shifted in
time, and therefore takes into consideration the multi time delay
relationships among the genes. The implementation of our method is
done in MATLAB and experimental results on Saccharomyces
cerevisiae gene expression data and comparison with other methods
indicate that it has a better performance.
Abstract: In this research work, poly (acrylonitrile-butadienestyrene)/
polypropylene (ABS/PP) blends were processed by melt
compounding in a twin-screw extruder. Upgrading of the thermal
characteristics of the obtained materials was attempted by the
incorporation of organically modified montmorillonite (OMMT), as
well as, by the addition of two types of compatibilizers;
polypropylene grafted with maleic anhydride (PP-g-MAH) and ABS
grafted with maleic anhydride (ABS-g-MAH). The effect of the
above treatments was investigated separately and in combination.
Increasing the PP content in ABS matrix seems to increase the
thermal stability of their blend and the glass transition temperature
(Tg) of SAN phase of ABS. From the other part, the addition of ABS
to PP promotes the formation of its β-phase, which is maximum at 30
wt% ABS concentration, and increases the crystallization temperature
(Tc) of PP. In addition, it increases the crystallization rate of PP.The
β-phase of PP in ABS/PP blends is reduced by the addition of
compatibilizers or/and organoclay reinforcement. The incorporation
of compatibilizers increases the thermal stability of PP and reduces
its melting (ΔΗm) and crystallization (ΔΗc) enthalpies. Furthermore it
decreases slightly the Tgs of PP and SAN phases of ABS/PP blends.
Regarding the storage modulus of the ABS/PP blends, it presents a
change in their behavior at about 10°C and return to their initial
behavior at ~110°C. The incorporation of OMMT to no compatibilized
and compatibilized ABS/PP blends enhances their storage modulus.
Abstract: Robustness is one of the primary performance criteria for an Intelligent Video Surveillance (IVS) system. One of the key factors in enhancing the robustness of dynamic video analysis is,providing accurate and reliable means for shadow detection. If left undetected, shadow pixels may result in incorrect object tracking and classification, as it tends to distort localization and measurement information. Most of the algorithms proposed in literature are computationally expensive; some to the extent of equalling computational requirement of motion detection. In this paper, the homogeneity property of shadows is explored in a novel way for shadow detection. An adaptive division image (which highlights homogeneity property of shadows) analysis followed by a relatively simpler projection histogram analysis for penumbra suppression is the key novelty in our approach.
Abstract: This work aims to describe the process of developing
services and applications of seamless communication within a
Telecom Italia long-term research project, which takes as central aim
the design of a wearable communication device. In particular, the
objective was to design a wrist phone integrated into everyday life of
people in full transparency. The methodology used to design the
wristwatch was developed through several subsequent steps also
involving the Personas Layering Framework. The data collected in
this phases have been very useful for designing an improved version
of the first two concepts of wrist phone going to change aspects
related to the four critical points expressed by the users.