Abstract: The numerical simulation has made tremendous
advances in investigating the blood flow phenomenon through elastic
arteries. Such study can be useful in demonstrating the disease
progression and hemodynamics of cardiovascular diseases such as
atherosclerosis. In the present study, patient specific case diagnosed
with partially stenosed complete right ICA and normal left carotid
bifurcation without any atherosclerotic plaque formation is
considered. 3D patient specific carotid bifurcation model is generated
based on CT scan data using MIMICS-4.0 and numerical analysis is
performed using FSI solver in ANSYS-14.5. The blood flow is
assumed to be incompressible, homogenous and Newtonian, while
the artery wall is assumed to be linearly elastic. The two-way
sequentially coupled transient FSI analysis is performed using FSI
solver for three pulse cycles. The hemodynamic parameters such as
flow pattern, Wall Shear Stress, pressure contours and arterial wall
deformation are studied at the bifurcation and critical zones such as
stenosis. The variation in flow behavior is studied throughout the
pulse cycle. Also, the simulation results reveal that there is a
considerable increase in the flow behavior in stenosed carotid in
contrast to the normal carotid bifurcation system. The investigation
also demonstrates the disturbed flow pattern especially at the
bifurcation and stenosed zone elevating the hemodynamics,
particularly during peak systole and later part of the pulse cycle. The
results obtained agree well with the clinical observation and
demonstrates the potential of patient specific numerical studies in
prognosis of disease progression and plaque rupture.
Abstract: In the present study, response surface methodology has been used to optimize turn-assisted deep cold rolling process of AISI 4140 steel. A regression model is developed to predict surface hardness and surface roughness using response surface methodology and central composite design. In the development of predictive model, deep cold rolling force, ball diameter, initial roughness of the workpiece, and number of tool passes are considered as model variables. The rolling force and the ball diameter are the significant factors on the surface hardness and ball diameter and numbers of tool passes are found to be significant for surface roughness. The predicted surface hardness and surface roughness values and the subsequent verification experiments under the optimal operating conditions confirmed the validity of the predicted model. The absolute average error between the experimental and predicted values at the optimal combination of parameter settings for surface hardness and surface roughness is calculated as 0.16% and 1.58% respectively. Using the optimal processing parameters, the surface hardness is improved from 225 to 306 HV, which resulted in an increase in the near surface hardness by about 36% and the surface roughness is improved from 4.84µm to 0.252 µm, which resulted in decrease in the surface roughness by about 95%. The depth of compression is found to be more than 300µm from the microstructure analysis and this is in correlation with the results obtained from the microhardness measurements. Taylor hobson talysurf tester, micro vickers hardness tester, optical microscopy and X-ray diffractometer are used to characterize the modified surface layer.
Abstract: Given the limited research on Small and Mediumsized
Enterprises’ (SMEs) contribution to Corporate Social
Responsibility (CSR) and even scarcer research on Swiss SMEs, this
paper helps to fill these gaps by enabling the identification of supranational
SME parameters. Thus, the paper investigates the current
state of SME practices in Switzerland and across 15 other countries.
Combining the degree to which SMEs demonstrate an explicit (or
business case) approach or see CSR as an implicit moral activity with
the assessment of their attributes for “variety of capitalism” defines
the framework of this comparative analysis. To outline Swiss small
business CSR patterns in particular, 40 SME owner-managers were
interviewed. A secondary data analysis of studies from different
countries laid groundwork for this comparative overview of small
business CSR. The paper identifies Swiss small business CSR as
driven by norms, values, and by the aspiration to contribute to
society, thus, as an implicit part of the day-to-day business. Similar to
most Central European, Mediterranean, Nordic, and Asian countries,
explicit CSR is still very rare in Swiss SMEs. Astonishingly, also
British and American SMEs follow this pattern in spite of their strong
and distinctly liberal market economies. Though other findings show
that nationality matters this research concludes that SME culture and
an informal CSR agenda are strongly formative and superseding even
forces of market economies, nationally cultural patterns, and
language. Hence, classifications of countries by their market system,
as found in the comparative capitalism literature, do not match the
CSR practices in SMEs as they do not mirror the peculiarities of their
business. This raises questions on the universality and
generalisability of unmediated, explicit management concepts,
especially in the context of small firms.
Abstract: In this study, three robust predicting methods, namely artificial neural network (ANN), adaptive neuro fuzzy inference system (ANFIS) and support vector machine (SVM) were used for computing the resonant frequency of A-shaped compact microstrip antennas (ACMAs) operating at UHF band. Firstly, the resonant frequencies of 144 ACMAs with various dimensions and electrical parameters were simulated with the help of IE3D™ based on method of moment (MoM). The ANN, ANFIS and SVM models for computing the resonant frequency were then built by considering the simulation data. 124 simulated ACMAs were utilized for training and the remaining 20 ACMAs were used for testing the ANN, ANFIS and SVM models. The performance of the ANN, ANFIS and SVM models are compared in the training and test process. The average percentage errors (APE) regarding the computed resonant frequencies for training of the ANN, ANFIS and SVM were obtained as 0.457%, 0.399% and 0.600%, respectively. The constructed models were then tested and APE values as 0.601% for ANN, 0.744% for ANFIS and 0.623% for SVM were achieved. The results obtained here show that ANN, ANFIS and SVM methods can be successfully applied to compute the resonant frequency of ACMAs, since they are useful and versatile methods that yield accurate results.
Abstract: Obesity and osteoporosis are the two diseases whose
increasing prevalence and high impact on the global morbidity and
mortality, during the two recent decades, have gained a status of
major health threats worldwide. Obesity purports to affect the bone
metabolism through complex mechanisms. Debated data on the
connection between the bone mineral density and fracture prevalence
in the obese patients are widely presented in literature. There is
evidence that the correlation of weight and fracture risk is sitespecific.
This study is aimed at determining the connection between
the bone mineral density (BMD) and trabecular bone score (TBS)
parameters in Ukrainian women suffering from obesity. We
examined 1025 40-89-year-old women, divided them into the groups
according to their body mass index: Group A included 360 women
with obesity whose BMI was ≥30 kg/m2, and Group B – 665 women
with no obesity and BMI of
Abstract: Intermittent behavior near the boundary of phase
synchronization in the presence of noise is studied. In certain range of
the coupling parameter and noise intensity the intermittency of eyelet
and ring intermittencies is shown to take place. Main results are
illustrated using the example of two unidirectional coupled Rössler
systems. Similar behavior is shown to take place in two
hydrodynamical models of Pierce diode coupled unidirectional.
Abstract: The aim of this investigation is to elaborate nearinfrared
methods for testing and recognition of chemical components
and quality in “Pannon wheat” allied (i.e. true to variety or variety
identified) milling fractions as well as to develop spectroscopic
methods following the milling processes and evaluate the stability of
the milling technology by different types of milling products and
according to sampling times, respectively. These wheat categories
produced under industrial conditions where samples were collected
versus sampling time and maximum or minimum yields. The changes
of the main chemical components (such as starch, protein, lipid) and
physical properties of fractions (particle size) were analysed by
dispersive spectrophotometers using visible (VIS) and near-infrared
(NIR) regions of the electromagnetic radiation. Close correlation
were obtained between the data of spectroscopic measurement
techniques processed by various chemometric methods (e.g. principal
component analysis [PCA], cluster analysis [CA]) and operation
condition of milling technology. It is obvious that NIR methods are
able to detect the deviation of the yield parameters and differences of
the sampling times by a wide variety of fractions, respectively. NIR
technology can be used in the sensitive monitoring of milling
technology.
Abstract: Submerged arc welding is a very complex process. It
is a very efficient and high performance welding process. In this
present study an attempt have been done to reduce the welding
distortion by increased amount of oxide flux through TiO2 in
submerged arc welding process. Care has been taken to avoid the
excessiveness of the adding agent for attainment of significant
results. Data Envelopment Analysis (DEA) based BAT algorithm is
used for the parametric optimization purpose in which DEA is used
to convert multi response parameters into a single response
parameter. The present study also helps to know the effectiveness of
the addition of TiO2 in active flux during submerged arc welding
process.
Abstract: Using the quantum hydrodynamic (QHD) model the
nonlinear properties of ion-acoustic waves in are lativistically
degenerate quantum plasma is investigated by deriving a nonlinear
Spherical Kadomtsev–Petviashvili (SKP) equation using the
standard reductive perturbation method equation. It was found that
the electron degeneracy parameter significantly affects the linear
and nonlinear properties of ion-acoustic waves in quantum plasma.
Abstract: Nowadays, the use of renewable energy sources has been increasingly great because of the cost increase and public demand for clean energy sources. One of the fastest growing sources is wind energy. In this paper, Wind Diesel Hybrid System (WDHS) comprising a Diesel Generator (DG), a Wind Turbine Generator (WTG), the Consumer Load, a Battery-based Energy Storage System (BESS), and a Dump Load (DL) is used. Voltage is controlled by Diesel Generator; the frequency is controlled by BESS and DL. The BESS elimination is an efficient way to reduce maintenance cost and increase the dynamic response. Simulation results with graphs for the frequency of Power System, active power, and the battery power are presented for load changes. The controlling parameters are optimized by using Imperialist Competitive Algorithm (ICA). The simulation results for the BESS/no BESS cases are compared. Results show that in no BESS case, the frequency control is more optimal than the BESS case by using ICA.
Abstract: The main function of Medium Access Control (MAC) is to share the channel efficiently between all nodes. In the real-time scenario, there will be certain amount of wastage in bandwidth due to back-off periods. More bandwidth will be wasted in idle state if the back-off period is very high and collision may occur if the back-off period is small. So, an optimization is needed for this problem. The main objective of the work is to reduce delay due to back-off period thereby reducing collision and increasing throughput. Here a method, called the virtual back-off algorithm (VBA) is used to optimize the back-off period and thereby it increases throughput and reduces collisions. The main idea is to optimize the number of transmission for every node. A counter is introduced at each node to implement this idea. Here counter value represents the sequence number. VBA is classified into two types VBA with counter sharing (VBA-CS) and VBA with no counter sharing (VBA-NCS). These two classifications of VBA are compared for various parameters. Simulation is done in NS-2 environment. The results obtained are found to be promising.
Abstract: There is not much effective guideline on development of design parameters selection on spring back for advanced high strength steel sheet metal in U-channel process during cold forming process. This paper presents the development of predictive model for spring back in U-channel process on advanced high strength steel sheet employing Response Surface Methodology (RSM). The experimental was performed on dual phase steel sheet, DP590 in Uchannel forming process while design of experiment (DoE) approach was used to investigates the effects of four factors namely blank holder force (BHF), clearance (C) and punch travel (Tp) and rolling direction (R) were used as input parameters using two level values by applying Full Factorial design (24 ). From a statistical analysis of variant (ANOVA), result showed that blank holder force (BHF), clearance (C) and punch travel (Tp) displayed significant effect on spring back of flange angle (β2 ) and wall opening angle (β1 ), while rolling direction (R) factor is insignificant. The significant parameters are optimized in order to reduce the spring back behavior using Central Composite Design (CCD) in RSM and the optimum parameters were determined. A regression model for spring back was developed. The effect of individual parameters and their response was also evaluated. The results obtained from optimum model are in agreement with the experimental values.
Abstract: Based on an indoor environmental quality (IEQ) index established by previous work that indicates the overall IEQ acceptance from the prospect of an occupant in residential buildings in terms of four IEQ factors - thermal comfort, indoor air quality, visual and aural comforts, this study develops a user-friendly IEQ calculator for iOS and Android users to calculate the occupant acceptance and compare the relative performance of IEQ in apartments. “IEQ calculator” is easy to use and it preliminarily illustrates the overall indoor environmental quality on the spot. Users simply input indoor parameters such as temperature, number of people and windows are opened or closed for the mobile application to calculate the scores in four areas: the comforts of temperature, brightness, noise and indoor air quality. The calculator allows the prediction of the best IEQ scenario on a quantitative scale. Any indoor environments under the specific IEQ conditions can be benchmarked against the predicted IEQ acceptance range. This calculator can also suggest how to achieve the best IEQ acceptance among a group of residents.
Abstract: This paper presented a study of three algorithms, the
equalization algorithm to equalize the transmission channel with ZF
and MMSE criteria, application of channel Bran A, and adaptive
filtering algorithms LMS and RLS to estimate the parameters of the
equalizer filter, i.e. move to the channel estimation and therefore
reflect the temporal variations of the channel, and reduce the error in
the transmitted signal. So far the performance of the algorithm
equalizer with ZF and MMSE criteria both in the case without noise,
a comparison of performance of the LMS and RLS algorithm.
Abstract: In this paper we propose a computer-aided solution
with Genetic Algorithms in order to reduce the drafting of reports:
FMEA analysis and Control Plan required in the manufacture of the
product launch and improved knowledge development teams for
future projects. The solution allows to the design team to introduce
data entry required to FMEA. The actual analysis is performed using
Genetic Algorithms to find optimum between RPN risk factor and
cost of production. A feature of Genetic Algorithms is that they are
used as a means of finding solutions for multi criteria optimization
problems. In our case, along with three specific FMEA risk factors is
considered and reduce production cost. Analysis tool will generate
final reports for all FMEA processes. The data obtained in FMEA
reports are automatically integrated with other entered parameters in
Control Plan. Implementation of the solution is in the form of an
application running in an intranet on two servers: one containing
analysis and plan generation engine and the other containing the
database where the initial parameters and results are stored. The
results can then be used as starting solutions in the synthesis of other
projects. The solution was applied to welding processes, laser cutting
and bending to manufacture chassis for buses. Advantages of the
solution are efficient elaboration of documents in the current project
by automatically generating reports FMEA and Control Plan using
multiple criteria optimization of production and build a solid
knowledge base for future projects. The solution which we propose is
a cheap alternative to other solutions on the market using Open
Source tools in implementation.
Abstract: For this study, a town based soil database created in
Gümüsçay District of Biga Town, Çanakkale, Turkey. Crop and
livestock production are major activities in the district. Nutrient
management is mainly based on commercial fertilizer application
ignoring the livestock manure. Within the boundaries of district, 122
soil sampling points determined over the satellite image. Soil samples
collected from the determined points with the help of handheld
Global Positioning System. Labeled samples were sent to a
commercial laboratory to determine 11 soil parameters including
salinity, pH, lime, organic matter, nitrogen, phosphorus, potassium,
iron, manganese, copper and zinc. Based on the test results soil maps
for mentioned parameters were developed using remote sensing, GIS,
and geostatistical analysis. In this study we developed a GIS database
that will be used for soil nutrient management. Methods were
explained and soil maps and their interpretations were summarized in
the study.
Abstract: More than 3000 plants of notable phyto-therapeutic
value grow in South Africa; these include Cissampelos capensis,
commonly known in Afrikaans as dawidjie or dawidjiewortel. C.
capensis is the most significant and popular medicinal plant used by
the Khoisan as well as other rural groups in the Western region of
South Africa. Its rhizomes are traditionally used to treat male fertility
problems. Yet, no studies have investigated the effects of this plant or
its extracts on human spermatozoa. Therefore, this study aimed at
investigating the effects of C. capensis rhizome extract (CRE)
fractions on ejaculated human spermatozoa in vitro. Spermatozoa
from a total of 77 semen samples were washed with human tubular
fluid medium supplemented with bovine serum albumin (HTF-BSA)
and incubated for 2 hours with 20 μg/ml progesterone (P4) followed
by incubation with different concentrations (0, 0.05, 0.5, 5, 50, 200
μg/ml) of fractionated CRE (F1=0% MeOH, F2=30% MeOH,
F3=60% MeOH and F4=100% MeOH) for 1.5 hours at 37°C. A
sample without addition of CRE fractions served as control. Samples
were analyzed for sperm motility, reactive oxygen species (ROS),
DNA-fragmentation, acrosome reaction and capacitation. Results
showed that F1 resulted in significantly higher values for ROS,
capacitation and hyper-activation compared to F2, F3, and F4 with
P4-stimulated samples generally having higher values. No significant
effect was found for the other parameters. In conclusion, alkaloids
present in F1 of CRE appear to have triggered sperm intrinsic ROS
production leading to sperm capacitation and acrosome reaction
induced by P4.
Abstract: A novel design technique employing CMOS Current
Feedback Operational Amplifier (CFOA) is presented. The feature of
consumption very low power in designing pseudo-OTA is used to
decreasing the total power consumption of the proposed CFOA. This
design approach applies pseudo-OTA as input stage cascaded with
buffer stage. Moreover, the DC input offset voltage and harmonic
distortion (HD) of the proposed CFOA are very low values compared
with the conventional CMOS CFOA due to the symmetrical input
stage. P-Spice simulation results are obtained using 0.18μm MIETEC
CMOS process parameters and supply voltage of ±1.2V, 50μA
biasing current. The p-spice simulation shows excellent improvement
of the proposed CFOA over existing CMOS CFOA. Some of these
performance parameters, for example, are DC gain of 62. dB, openloop
gain bandwidth product of 108 MHz, slew rate (SR+) of
+71.2V/μS, THD of -63dB and DC consumption power (PC) of
2mW.
Abstract: Microbes have been used to solve environmental
problems for many years. The role of microorganism to sequester,
precipitate or alter the oxidation state of various heavy metals has
been extensively studied. Treatment using microorganism interacts
with toxic metal are very diverse. The purpose of this research is to
remove the mercury using Pseudomonas putida (P. putida), pure
culture ATTC 49128 at optimum growth parameters such as
techniques of culture, acclimatization time and speed of incubator
shaker. Thus, in this study, the optimum growth parameters of P.
putida were obtained to achieve the maximum of mercury removal.
Based on the optimum parameters of P. putida for specific growth
rate, the removal of two different mercury concentration, 1 ppm and
4 ppm were studied. From mercury nitrate solution, a mercuryresistant
bacterial strain which is able to reduce from ionic mercury
to metallic mercury was used to reduce ionic mercury. The overall
levels of mercury removal in this study were between 80% and 89%.
The information obtained in this study is of fundamental for
understanding of the survival of P. putida ATTC 49128 in mercury
solution. Thus, microbial mercury removal is a potential
bioremediation for wastewater especially in petrochemical industries
in Malaysia.
Abstract: Potassium borates, which are widely used in welding
and metal refining industry, as a lubricating oil additive, cement
additive, fiberglass additive and insulation compound, are one of the
important groups of borate minerals. In this study the production of a
potassium borate mineral via hydrothermal method is aimed. The
potassium source of potassium nitrate (KNO3) was used along with a
sodium source of sodium hydroxide (NaOH) and boron source of
boric acid (H3BO3). The constant parameters of reaction temperature
and reaction time were determined as 80°C and 1 h, respectively. The
molar ratios of 1:1:3 (as KNO3:NaOH:H3BO3), 1:1:4, 1:1:5, 1:1:6
and 1:1:7 were used. Following the synthesis the identifications of
the produced products were conducted by X-Ray Diffraction (XRD),
Fourier Transform Infrared Spectroscopy (FT-IR) and Raman
Spectroscopy. The results of the experiments and analysis showed in
the ratio of 1:1:6, the Santite mineral with powder diffraction file
number (pdf no.) of 01-072-1688, which is known as potassium
pentaborate (KB5O8·4H2O) was synthesized as best.