Abstract: In this paper, a one-dimensional numerical approach is
used to study the effect of applying electrohydrodynamics on the
temperature and species mass fraction profiles along the microcombustor.
Premixed mixture is H2-Air with a multi-step chemistry
(9 species and 19 reactions). In the micro-scale combustion because
of the increasing ratio of area-to-volume, thermal and radical
quenching mechanisms are important. Also, there is a significant heat
loss from the combustor walls. By inserting a number of electrodes
into micro-combustor and applying high voltage to them corona
discharge occurs. This leads in moving of induced ions toward
natural molecules and colliding with them. So this phenomenon
causes the movement of the molecules and reattaches the flow to the
walls. It increases the velocity near the walls that reduces the wall
boundary layer. Consequently, applying electrohydrodynamics
mechanism can enhance the temperature profile in the microcombustor.
Ultimately, it prevents the flame quenching in microcombustor.
Abstract: The present paper considers the steady free convection
boundary layer flow of a viscoelastic fluid on solid sphere with
Newtonian heating. The boundary layer equations are an order higher
than those for the Newtonian (viscous) fluid and the adherence
boundary conditions are insufficient to determine the solution of
these equations completely. Thus, the augmentation an extra
boundary condition is needed to perform the numerical
computational. The governing boundary layer equations are first
transformed into non-dimensional form by using special
dimensionless group and then solved by using an implicit finite
difference scheme. The results are displayed graphically to illustrate
the influence of viscoelastic K and Prandtl Number Pr parameters on
skin friction, heat transfer, velocity profiles and temperature profiles.
Present results are compared with the published papers and are found
to concur very well.
Abstract: When the foundations of structures under cyclic
loading with amplitudes less than their permissible load, the concern exists often for the amount of uniform and non-uniform settlement of
such structures. Storage tank foundations with numerous filling and discharging and railways ballast course under repeating
transportation loads are examples of such conditions. This paper
deals with the effects of using the new generation of reinforcements,
Grid-Anchor, for the purpose of reducing the permanent settlement
of these foundations under the influence of different proportions of
the ultimate load. Other items such as the type and the number of
reinforcements as well as the number of loading cycles are studied numerically. Numerical models were made using the Plaxis3D
Tunnel finite element code. The results show that by using gridanchor
and increasing the number of their layers in the same
proportion as that of the cyclic load being applied, the amount of
permanent settlement decreases up to 42% relative to unreinforced
condition depends on the number of reinforcement layers and percent
of applied load and the number of loading cycles to reach a constant
value of dimensionless settlement decreases up to 20% relative to
unreinforced condition.
Abstract: Heart failure is the most common reason of death
nowadays, but if the medical help is given directly, the patient-s life
may be saved in many cases. Numerous heart diseases can be
detected by means of analyzing electrocardiograms (ECG). Artificial
Neural Networks (ANN) are computer-based expert systems that
have proved to be useful in pattern recognition tasks. ANN can be
used in different phases of the decision-making process, from
classification to diagnostic procedures. This work concentrates on a
review followed by a novel method.
The purpose of the review is to assess the evidence of healthcare
benefits involving the application of artificial neural networks to the
clinical functions of diagnosis, prognosis and survival analysis, in
ECG signals. The developed method is based on a compound neural
network (CNN), to classify ECGs as normal or carrying an
AtrioVentricular heart Block (AVB). This method uses three
different feed forward multilayer neural networks. A single output
unit encodes the probability of AVB occurrences. A value between 0
and 0.1 is the desired output for a normal ECG; a value between 0.1
and 1 would infer an occurrence of an AVB. The results show that
this compound network has a good performance in detecting AVBs,
with a sensitivity of 90.7% and a specificity of 86.05%. The accuracy
value is 87.9%.
Abstract: An analysis is performed to study the influence of nonuniform double slot suction on a steady laminar boundary layer flow over a rotating sphere when fluid properties such as viscosity and Prandtl number are inverse linear functions of temperature. Nonsimilar solutions have been obtained from the starting point of the streamwise co-ordinate to the exact point of separation. The difficulties arising at the starting point of the streamwise co-ordinate, at the edges of the slot and at the point of separation have been overcome by applying an implicit finite difference scheme in combination with the quasi-linearization technique and an appropriate selection of the finer step sizes along the stream-wise direction. The present investigation shows that the point of ordinary separation can be delayed by nonuniform double slot suction if the mass transfer rate is increased and also if the slots are positioned further downstream. In addition, the investigation reveals that double slot suction is found to be more effective compared to a single slot suction in delaying ordinary separation. As rotation parameter increase the point of separation moves upstream direction.
Abstract: In this paper, we have proposed a Haar wavelet quasilinearization
method to solve the well known Blasius equation. The
method is based on the uniform Haar wavelet operational matrix
defined over the interval [0, 1]. In this method, we have proposed the
transformation for converting the problem on a fixed computational
domain. The Blasius equation arises in the various boundary layer
problems of hydrodynamics and in fluid mechanics of laminar
viscous flows. Quasi-linearization is iterative process but our
proposed technique gives excellent numerical results with quasilinearization
for solving nonlinear differential equations without any
iteration on selecting collocation points by Haar wavelets. We have
solved Blasius equation for 1≤α ≤ 2 and the numerical results are
compared with the available results in literature. Finally, we
conclude that proposed method is a promising tool for solving the
well known nonlinear Blasius equation.
Abstract: In this paper, we present a comparative study between two computer vision systems for objects recognition and tracking, these algorithms describe two different approach based on regions constituted by a set of pixels which parameterized objects in shot sequences. For the image segmentation and objects detection, the FCM technique is used, the overlapping between cluster's distribution is minimized by the use of suitable color space (other that the RGB one). The first technique takes into account a priori probabilities governing the computation of various clusters to track objects. A Parzen kernel method is described and allows identifying the players in each frame, we also show the importance of standard deviation value research of the Gaussian probability density function. Region matching is carried out by an algorithm that operates on the Mahalanobis distance between region descriptors in two subsequent frames and uses singular value decomposition to compute a set of correspondences satisfying both the principle of proximity and the principle of exclusion.
Abstract: Supersonic hydrogen-air cylindrical mixing layer is
numerically analyzed to investigate the effect of inlet swirl on
ignition time delay in scramjets. Combustion is treated using detail
chemical kinetics. One-equation turbulence model of Spalart and
Allmaras is chosen to study the problem and advection upstream
splitting method is used as computational scheme. The results show
that swirling both fuel and oxidizer streams may drastically decrease
the ignition distance in supersonic combustion, unlike using the swirl
just in fuel stream which has no helpful effect.
Abstract: Group-III nitride material as particularly AlxGa1-xN is
one of promising optoelectronic materials to require for shortwavelength
devices. To achieve the high-quality AlxGa1-xN films for
a high performance of such devices, AlN-nucleation layers are the
important factor. To improve the AlN-nucleation layers with a
variation of Ga-addition, XRD measurements were conducted to
analyze the crystalline quality of the subsequent Al0.1Ga0.9N with the
minimum ω-FWHMs of (0002) and (10-10) reflections of 425 arcsec
and 750 arcsec, respectively. SEM and AFM measurements were
performed to observe the surface morphology and TEM
measurements to identify the microstructures and orientations.
Results showed that the optimized Ga-atoms in the Al(Ga)Nnucleation
layers improved the surface diffusion to form moreuniform
crystallites in structure and size, better alignment of each
crystallite, and better homogeneity of island distribution. This, hence,
improves the orientation of epilayers on the Si-surface and finally
improves the crystalline quality and reduces the residual strain of
subsequent Al0.1Ga0.9N layers.
Abstract: In turning hardened steel, polycrystalline cubic boron
nitride (cBN) compacts are widely used, due to their higher hardness
and higher thermal conductivity. However, in milling hardened steel,
fracture of cBN cutting tools readily occurs because they have poor
fracture toughness. Therefore, coated cemented carbide tools, which
have good fracture toughness and wear resistance, are generally
widely used. In this study, hardened steel (ASTM D2, JIS SKD11,
60HRC) was milled with three physical vapor deposition
(PVD)-coated cemented carbide end mill cutters in order to determine
effective tool materials for cutting hardened steel at high cutting
speeds. The coating films used were (Ti,W)N/(Ti,W,Si)N and
(Ti,W)N/(Ti,W,Si,Al)N coating films. (Ti,W,Si,Al)N is a new type of
coating film. The inner layer of the (Ti,W)N/(Ti,W,Si)N and
(Ti,W)N/(Ti,W,Si,Al)N coating system is (Ti,W)N coating film, and
the outer layer is (Ti,W,Si)N and (Ti,W,Si,Al)N coating films,
respectively. Furthermore, commercial (Ti,Al)N-based coating film
was also used. The following results were obtained: (1) In milling
hardened steel at a cutting speed of 3.33 m/s, the tool wear width of the
(Ti,W)N/(Ti,W,Si,Al)N-coated tool was smaller than that of the
(Ti,W)N/(Ti,W,Si)N-coated tool. And, compared with the commercial
(Ti,Al)N, the tool wear width of the (Ti,W)N/(Ti,W,Si,Al)N-coated
tool was smaller than that of the (Ti,Al)N-coated tool. (2) The tool
wear of the (Ti,W)N/(Ti,W,Si,Al)N-coated tool increased with an
increase in cutting speed. (3) The (Ti,W)N/(Ti,W,Si,Al)N-coated
cemented carbide was an effective tool material for high-speed cutting
below a cutting speed of 3.33 m/s.
Abstract: In this paper, the application of neural networks to study the design of short-term load forecasting (STLF) Systems for Illam state located in west of Iran was explored. One important architecture of neural networks named Multi-Layer Perceptron (MLP) to model STLF systems was used. Our study based on MLP was trained and tested using three years (2004-2006) data. The results show that MLP network has the minimum forecasting error and can be considered as a good method to model the STLF systems.
Abstract: Inverse kinematics analysis plays an important role in developing a robot manipulator. But it is not too easy to derive the inverse kinematic equation of a robot manipulator especially robot manipulator which has numerous degree of freedom. This paper describes an application of Artificial Neural Network for modeling the inverse kinematics equation of a robot manipulator. In this case, the robot has three degree of freedoms and the robot was implemented for drilling a printed circuit board. The artificial neural network architecture used for modeling is a multilayer perceptron networks with steepest descent backpropagation training algorithm. The designed artificial neural network has 2 inputs, 2 outputs and varies in number of hidden layer. Experiments were done in variation of number of hidden layer and learning rate. Experimental results show that the best architecture of artificial neural network used for modeling inverse kinematics of is multilayer perceptron with 1 hidden layer and 38 neurons per hidden layer. This network resulted a RMSE value of 0.01474.
Abstract: This paper features the modeling and design of a Fast
Output Sampling (FOS) Feedback control technique for the Active
Vibration Control (AVC) of a smart flexible aluminium cantilever
beam for a Single Input Single Output (SISO) case. Controllers are
designed for the beam by bonding patches of piezoelectric layer as
sensor / actuator to the master structure at different locations along
the length of the beam by retaining the first 2 dominant vibratory
modes. The entire structure is modeled in state space form using the
concept of piezoelectric theory, Euler-Bernoulli beam theory, Finite
Element Method (FEM) and the state space techniques by dividing
the structure into 3, 4, 5 finite elements, thus giving rise to three
types of systems, viz., system 1 (beam divided into 3 finite
elements), system 2 (4 finite elements), system 3 (5 finite elements).
The effect of placing the sensor / actuator at various locations along
the length of the beam for all the 3 types of systems considered is
observed and the conclusions are drawn for the best performance and
for the smallest magnitude of the control input required to control the
vibrations of the beam. Simulations are performed in MATLAB. The
open loop responses, closed loop responses and the tip displacements
with and without the controller are obtained and the performance of
the proposed smart system is evaluated for vibration control.
Abstract: In this investigation Salicylic acid, Sulfosalicylic acid
and Acetyl salicylic acid were chosen as a sample for thin layer
chromatography (TLC) on silica gel plates. Bicarbonate buffer at
different pH containing different amounts of boric acid was applied
as mobile phase. Specific interaction of these substances with boric
acid has effect on Rf in thin layer chromatography. Regular and
similar trend was observed in variations of Rf for mentioned
compounds in TLC by altering of percentages of boric acid in mobile
phase in pH range of 8-10. Also effect of organic solvent, mixture of
water/ organic solvent and organic solvent containing boric acid as
mobile phase was studied.
Abstract: The aim of this research is to use artificial neural networks computing technology for estimating the net heating value (NHV) of crude oil by its Properties. The approach is based on training the neural network simulator uses back-propagation as the learning algorithm for a predefined range of analytically generated well test response. The network with 8 neurons in one hidden layer was selected and prediction of this network has been good agreement with experimental data.
Abstract: The spiral angle of the elementary cellulose fibril in
the wood cell wall, often called microfibril angle, (MFA). Microfibril
angle in hardwood is one of the key determinants of solid timber
performance due to its strong influence on the stiffness, strength,
shrinkage, swelling, thermal-dynamics mechanical properties and
dimensional stability of wood. Variation of MFA (degree) in the S2
layer of the cell walls among Acacia mangium trees was determined
using small-angle X-ray scattering (SAXS). The length and
orientation of the microfibrils of the cell walls in the irradiated
volume of the thin samples are measured using SAXS and optical
microscope for 3D surface measurement. The undetermined
parameters in the analysis are the MFA, (M) and the standard
deviation (σФ) of the intensity distribution arising from the wandering
of the fibril orientation about the mean value. Nine separate pairs of
values are determined for nine different values of the angle of the
incidence of the X-ray beam relative to the normal to the radial
direction in the sample. The results show good agreement. The
curve distribution of scattered intensity for the real cell wall structure
is compared with that calculated with that assembly of rectangular
cells with the same ratio of transverse to radial cell wall length. It is
demonstrated that for β = 45°, the peaks in the curve intensity
distribution for the real and the rectangular cells coincide. If this
peak position is Ф45, then the MFA can be determined from the
relation M = tan-1 (tan Ф45 / cos 45°), which is precise for rectangular
cells. It was found that 92.93% of the variation of MFA can be
attributed to the distance from pith to bark. Here we shall present our
results of the MFA in the cell wall with respect to its shape, structure
and the distance from pith to park as an important fast check and yet
accurate towards the quality of wood, its uses and application.
Abstract: The interaction of the blade tip with the casing
boundary layer and the leakage flow may lead to a kind of cavitation
namely tip vortex cavitation. In this study, the onset of tip vortex
cavitation was experimentally investigated in an axial flow pump.
For a constant speed and a fixed angle of attack and by changing the
flow rate, the pump head, input power, output power and efficiency
were calculated and the pump characteristic curves were obtained.
The cavitation phenomenon was observed with a camera and a
stroboscope. Finally, the critical flow region, which tip vortex
cavitation might have occurred, was identified. The results show that
just by adjusting the flow rate, out of the specified region, the
possibility of occurring tip vortex cavitation, decreases to a great
extent.
Abstract: A complete spectral representation for the
electromagnetic field of planar multilayered waveguides
inhomogeneously filled with omega media is presented. The problem
of guided electromagnetic propagation is reduced to an eigenvalue
equation related to a 2 ´ 2 matrix differential operator. Using the
concept of adjoint waveguide, general bi-orthogonality relations for
the hybrid modes (either from the discrete or from the continuous
spectrum) are derived. For the special case of homogeneous layers
the linear operator formalism is reduced to a simple 2 ´ 2 coupling
matrix eigenvalue problem. Finally, as an example of application, the
surface and the radiation modes of a grounded omega slab waveguide
are analyzed.
Abstract: The conjugate gradient optimization algorithm
usually used for nonlinear least squares is presented and is
combined with the modified back propagation algorithm yielding
a new fast training multilayer perceptron (MLP) algorithm
(CGFR/AG). The approaches presented in the paper consist of
three steps: (1) Modification on standard back propagation
algorithm by introducing gain variation term of the activation
function, (2) Calculating the gradient descent on error with
respect to the weights and gains values and (3) the determination
of the new search direction by exploiting the information
calculated by gradient descent in step (2) as well as the previous
search direction. The proposed method improved the training
efficiency of back propagation algorithm by adaptively modifying
the initial search direction. Performance of the proposed method
is demonstrated by comparing to the conjugate gradient algorithm
from neural network toolbox for the chosen benchmark. The
results show that the number of iterations required by the
proposed method to converge is less than 20% of what is required
by the standard conjugate gradient and neural network toolbox
algorithm.
Abstract: Biometric techniques are gaining importance for
personal authentication and identification as compared to the
traditional authentication methods. Biometric templates are
vulnerable to variety of attacks due to their inherent nature. When a
person-s biometric is compromised his identity is lost. In contrast to
password, biometric is not revocable. Therefore, providing security
to the stored biometric template is very crucial. Crypto biometric
systems are authentication systems, which blends the idea of
cryptography and biometrics. Fuzzy vault is a proven crypto
biometric construct which is used to secure the biometric templates.
However fuzzy vault suffer from certain limitations like nonrevocability,
cross matching. Security of the fuzzy vault is affected
by the non-uniform nature of the biometric data. Fuzzy vault when
hardened with password overcomes these limitations. Password
provides an additional layer of security and enhances user privacy.
Retina has certain advantages over other biometric traits. Retinal
scans are used in high-end security applications like access control to
areas or rooms in military installations, power plants, and other high
risk security areas. This work applies the idea of fuzzy vault for
retinal biometric template. Multimodal biometric system
performance is well compared to single modal biometric systems.
The proposed multi modal biometric fuzzy vault includes combined
feature points from retina and fingerprint. The combined vault is
hardened with user password for achieving high level of security.
The security of the combined vault is measured using min-entropy.
The proposed password hardened multi biometric fuzzy vault is
robust towards stored biometric template attacks.