Abstract: Workload and resource management are two essential functions provided at the service level of the grid software infrastructure. To improve the global throughput of these software environments, workloads have to be evenly scheduled among the available resources. To realize this goal several load balancing strategies and algorithms have been proposed. Most strategies were developed in mind, assuming homogeneous set of sites linked with homogeneous and fast networks. However for computational grids we must address main new issues, namely: heterogeneity, scalability and adaptability. In this paper, we propose a layered algorithm which achieve dynamic load balancing in grid computing. Based on a tree model, our algorithm presents the following main features: (i) it is layered; (ii) it supports heterogeneity and scalability; and, (iii) it is totally independent from any physical architecture of a grid.
Abstract: An experiment was implemented in a filed in the south of Morocco to evaluate the effects of domestic treated wastewater use for irrigation of amaranth crop under semi-arid conditions. Three varieties (A0020, A0057 & A211) were tested and irrigated using domestic treated wastewater EC1 (0,92 dS/m) as control, EC3 (3dS/m) and EC6 (6dS/m) obtained by adding sea water. In term of growth, an increase of the EC level of applied irrigation water reduced significantly the plant-s height, leaf area, fresh and dry weight measured at vegetative, flowering and maturity stage for all varieties. Even with the application of the EC6, yields were relatively higher in comparison with the once obtained in normal cultivation conditions. A significant accumulation of nitrate, chloride and sodium in soil layers during the crop cycle was noted. The use of treated waste water for its irrigation is proved to be possible. The variety A211 had showed to be less sensitive to salinity stress and it could be more promising its introduction to study area.
Abstract: In this paper, a few chattering-free Sliding Mode Controllers (SMC) are proposed to stabilize an Active Magnetic Bearing (AMB) system with gyroscopic effect that is proportional to the rotor speed. The improved switching terms of the controller inherited from the saturation-type function and boundary layer control technique is shown to be able to achieve bounded and asymptotic stability, respectively, while the chattering effect in the input is attenuated. This is proven to be advantageous for AMB system since minimization of chattering results in optimized control effort. The performance of each controller is demonstrated via result of simulation in which the measurement of the total consumed energy and maximum control magnitude of each controller illustrates the effectiveness of the proposed controllers.
Abstract: The objective of this work is to study the influence of the properties of the substrate on the retrofit (thin repair) of damaged concrete elements, with the SCC. Fluidity, principal characteristic of the SCC, would enable it to cover and adhere to the concrete to be repaired. Two aspects of repair are considered, the bond (Adhesion) and the tensile strength and the cracking. The investigation is experimental; It was conducted over test specimens made up of ordinary concrete prepared and hardened in advance (the material to be repaired) over which a self compacting concrete layer is cast. Three alternatives of SC concrete and one ordinary concrete (comparison) were tested. It appears that the self-compacting concrete constitutes a good material for repairing. It follows perfectly the surfaces- forms to be repaired and allows a perfect bond. Fracture tests made on specimens of self-compacting concrete show a brittle behaviour. However when a small percentage of fibres is added, the resistance to cracking is very much improve.
Abstract: Some methodologies were compared in providing
erosion maps of surface, rill and gully and erosion features, in
research which took place in the Varamin sub-basin, north-east
Tehran, Iran. A photomorphic unit map was produced from
processed satellite images, and four other maps were prepared by the
integration of different data layers, including slope, plant cover,
geology, land use, rocks erodibility and land units. Comparison of
ground truth maps of erosion types and working unit maps indicated
that the integration of land use, land units and rocks erodibility layers
with satellite image photomorphic units maps provide the best
methods in producing erosion types maps.
Abstract: Standard packaging and interconnection technologies
of power devices have difficulties meeting the increasing thermal
demands of new application fields of power electronics devices.
Main restrictions are the decreasing reliability of bond-wires and
solder layers with increasing junction temperature. In the last few
years intensive efforts have been invested in developing new
packaging and interconnection solutions which may open a path to
future application of power devices. In this paper, the main failure
mechanisms of power devices are described and principle of new
packaging and interconnection concepts and their power cycling
reliability are presented.
Abstract: Linear stability of wake-shear layers in two-phase
shallow flows is analyzed in the present paper. Stability analysis is
based on two-dimensional shallow water equations. It is assumed that
the fluid contains uniformly distributed solid particles. No dynamic
interaction between the carrier fluid and particles is expected in the
initial moment. Linear stability curves are obtained for different
values of the particle loading parameter, the velocity ratio and the
velocity deficit. It is shown that the increase in the velocity ratio
destabilizes the flow. The particle loading parameter has a stabilizing
effect on the flow. The role of the velocity deficit is also
destabilizing: the increase of the velocity deficit leads to less stable
flow.
Abstract: This paper proposes an efficient lattice-reduction-aided
detection (LRD) scheme to improve the detection performance of
MIMO-OFDM system. In this proposed scheme, V candidate symbols
are considered at the first layer, and V probable streams are
detected with LRD scheme according to the first detected V candidate
symbols. Then, the most probable stream is selected through a ML
test. Since the proposed scheme can more accurately detect initial
symbol and can reduce transmission of error to rest symbols, the
proposed scheme shows more improved performance than conventional
LRD with very low complexity.
Abstract: Commercial nanocomposite food packaging type nano-silver containers were characterised using scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDX). The presence of nanoparticles consistent with the incorporation of 1% nano-silver (Ag) and 0.1% titanium dioxide (TiO2) nanoparticle into polymeric materials formed into food containers was confirmed. Both nanomaterials used in this type of packaging appear to be embedded in a layered configuration within the bulk polymer. The dimensions of the incorporated nanoparticles were investigated using X-ray diffraction (XRD) and determined by calculation using the Scherrer Formula; these were consistent with Ag and TiO2 nanoparticles in the size range 20-70nm both were spherical shape nanoparticles. Antimicrobial assessment of the nanocomposite container has also been performed and the results confirm the antimicrobial activity of Ag and TiO2 nanoparticles in food packaging containers. Migration assessments were performed in a wide range of food matrices to determine the migration of nanoparticles from the packages. The analysis was based upon the relevant European safety Directives and involved the application of inductively coupled plasma mass spectrometry (ICP-MS) to identify the range of migration risk. The data pertain to insignificance levels of migration of Ag and TiO2 nanoparticles into the selected food matrices.
Abstract: The photoluminescence (PL) at 1.55 μm from
semiconducting β-FeSi2 has attracted a noticeable interest for
silicon-based optoelectronic applications. Moreover, its high optical
absorption coefficient (higher than 105 cm-1 above 1.0 eV) allows this
semiconducting material to be used as photovoltanics devices.
A clear PL spectrum for β-FeSi2 was observed by Cu or Au coating
on Si(001). High-crystal-quality β-FeSi2 with a low-level nonradiative
center was formed on a Cu- or Au- reated Si layer. This method of
deposition can be applied to other materials requiring high crystal
quality.
Abstract: The problem of natural convection about a cone embedded in a porous medium at local Rayleigh numbers based on the boundary layer approximation and the Darcy-s law have been studied before. Similarity solutions for a full cone with the prescribed wall temperature or surface heat flux boundary conditions which is the power function of distance from the vertex of the inverted cone give us a third-order nonlinear differential equation. In this paper, an approximate method for solving higher-order ordinary differential equations is proposed. The approach is based on a rational Chebyshev Tau (RCT) method. The operational matrices of the derivative and product of rational Chebyshev (RC) functions are presented. These matrices together with the Tau method are utilized to reduce the solution of the higher-order ordinary differential equations to the solution of a system of algebraic equations. We also present the comparison of this work with others and show that the present method is applicable.
Abstract: An analysis is made of the flow of an incompressible viscoelastic fluid (of small memory) over a porous plate subject to suction or blowing. It is found that velocity at a point increases with increase in the elasticity in the fluid. It is also shown that wall shear stress depends only on suction and is also independent of the material of fluids. No steady solution for velocity distribution exists when there is blowing at the plate. Temperature distribution in the boundary layer is determined and it is found that temperature at a point decreases with increase in the elasticity in the fluid.
Abstract: A frictionless contact problem for a two-layer orthotropic elastic medium loaded through a rigid flat stamp is considered. It is assumed that tensile tractions are not allowed and only compressive tractions can be transmitted across the interface. In the solution, effect of gravity is taken into consideration. If the external load on the rigid stamp is less than or equal to a critical value, continuous contact between the layers is maintained. The problem is expressed in terms of a singular integral equation by using the theory of elasticity and the Fourier transforms. Numerical results for initial separation point, critical separation load and contact stress distribution are presented.
Abstract: A numerical study on the influence of electroosmotic flow on analyte preconcentration by isotachophoresis ( ITP) is made. We consider that the double layer induced electroosmotic flow ( EOF) counterbalance the electrophoretic velocity and a stationary ITP stacked zones results. We solve the Navier-Stokes equations coupled with the Nernst-Planck equations to determine the local convective velocity and the preconcentration dynamics of ions. Our numerical algorithm is based on a finite volume method along with a secondorder upwind scheme. The present numerical algorithm can capture the the sharp boundaries of step-changes ( plateau mode) or zones of steep gradients ( peak mode) accurately. The convection of ions due to EOF reduces the resolution of the ITP transition zones and produces a dispersion in analyte zones. The role of the electrokinetic parameters which induces dispersion is analyzed. A one-dimensional model for the area-averaged concentrations based on the Taylor-Aristype effective diffusivity is found to be in good agreement with the computed solutions.
Abstract: The importance of machining process in today-s
industry requires the establishment of more practical approaches to
clearly represent the intimate and severe contact on the tool-chipworkpiece
interfaces. Mathematical models are developed using the
measured force signals to relate each of the tool-chip friction
components on the rake face to the operating cutting parameters in
rough turning operation using multilayers coated carbide inserts.
Nonlinear modeling proved to have high capability to detect the
nonlinear functional variability embedded in the experimental data.
While feedrate is found to be the most influential parameter on the
friction coefficient and its related force components, both cutting
speed and depth of cut are found to have slight influence. Greater
deformed chip thickness is found to lower the value of friction
coefficient as the sliding length on the tool-chip interface is reduced.
Abstract: In this work, the physical based device model of
AlGaN/GaN high electron mobility transistors (HEMTs) has been
established and the corresponding device operation behavior has
been investigated also by using Sentaurus TCAD from Synopsys.
Advanced AlGaN/GaN hetero-structures with GaN cap layer and AlN
spacer have been considered and the GaN cap layer and AlN spacer
are found taking important roles on the gate leakage blocking and
off-state breakdown voltage enhancement.
Abstract: Chaos and fractals are novel fields of physics and mathematics showing up a new way of universe viewpoint and creating many ideas to solve several present problems. In this paper, a novel algorithm based on the chaotic sequence generator with the highest ability to adapt and reach the global optima is proposed. The adaptive ability of proposal algorithm is flexible in 2 steps. The first one is a breadth-first search and the second one is a depth-first search. The proposal algorithm is examined by 2 functions, the Camel function and the Schaffer function. Furthermore, the proposal algorithm is applied to optimize training Multilayer Neural Networks.
Abstract: Human identification at a distance has recently gained
growing interest from computer vision researchers. Gait recognition
aims essentially to address this problem by identifying people based
on the way they walk [1]. Gait recognition has 3 steps. The first step
is preprocessing, the second step is feature extraction and the third
one is classification. This paper focuses on the classification step that
is essential to increase the CCR (Correct Classification Rate).
Multilayer Perceptron (MLP) is used in this work. Neural Networks
imitate the human brain to perform intelligent tasks [3].They can
represent complicated relationships between input and output and
acquire knowledge about these relationships directly from the data
[2]. In this paper we apply MLP NN for 11 views in our database and
compare the CCR values for these views. Experiments are performed
with the NLPR databases, and the effectiveness of the proposed
method for gait recognition is demonstrated.
Abstract: Sliding mode control with a fuzzy boundary layer is presented to hydraulic position control problem in this paper. A nonlinear hydraulic servomechanism which has an asymmetric cylinder is modeled and simulated first, then the proposed control scheme is applied to this model versus the conventional sliding mode control. Simulation results proved that the chattering free position control is achieved by tuning the fuzzy scaling factors properly.
Abstract: This paper presents the modeling results of an
innovative system for the temperature control in the interior
compartment of a stationary automobile facing the solar energy from
the sun. A very thin layer of PCM inside a pouch placed in the
ceiling of the car in which the heating energy is absorbed and release
with melting and solidification of phase change materials. As a result
the temperature of the car interior is maintained in the comfort
condition. The amount of required PCM has been calculated to be
about 755 g. The PCM-temperature controlling system is simple and
has a potential to be implemented as a practical solution to prevent
undesirable heating of the automobile-s cabin.