Abstract: This paper presents a means for reducing the torque
variation during the revolution of a vertical-axis water turbine
(VAWaterT) by increasing the blade number. For this purpose, twodimensional
CFD analyses have been performed on a straight-bladed
Darrieus-type rotor. After describing the computational model and
the relative validation procedure, a complete campaign of
simulations, based on full RANS unsteady calculations, is proposed
for a three, four and five-bladed rotor architectures, characterized by
a NACA 0025 airfoil. For each proposed rotor configuration, flow
field characteristics are investigated at several values of tip speed
ratio, allowing a quantification of the influence of blade number on
flow geometric features and dynamic quantities, such as rotor torque
and power. Finally, torque and power curves are compared for the
three analyzed architectures, achieving a quantification of the effect
of blade number on overall rotor performance.
Abstract: The precision of heat flux simulation influences the
temperature field and test aberration for TB test and also reflects the
test level for spacecraft development. This paper describes TB tests for
a small satellite using solar simulator, electric heaters, calrod heaters
to evaluate the difference of the three methods. Under the same
boundary condition, calrod heaters cases were about 6oC higher than
solar simulator cases and electric heaters cases for
non-external-heat-flux cases (extreme low temperature cases). While
calrod heaters cases and electric heaters cases were 5~7oC and 2~3oC
lower than solar simulator cases respectively for high temperature
cases. The results show that the solar simulator is better than calrod
heaters for its better collimation, non-homogeneity and stability.
Abstract: The POD-assisted projective integration method based on the equation-free framework is presented in this paper. The method is essentially based on the slow manifold governing of given system. We have applied two variants which are the “on-line" and “off-line" methods for solving the one-dimensional viscous Bergers- equation. For the on-line method, we have computed the slow manifold by extracting the POD modes and used them on-the-fly along the projective integration process without assuming knowledge of the underlying slow manifold. In contrast, the underlying slow manifold must be computed prior to the projective integration process for the off-line method. The projective step is performed by the forward Euler method. Numerical experiments show that for the case of nonperiodic system, the on-line method is more efficient than the off-line method. Besides, the online approach is more realistic when apply the POD-assisted projective integration method to solve any systems. The critical value of the projective time step which directly limits the efficiency of both methods is also shown.
Abstract: In this paper electrical characteristics of various kinds
of multiple-gate silicon nanowire transistors (SNWT) with the
channel length equal to 7 nm are compared. A fully ballistic quantum
mechanical transport approach based on NEGF was employed to
analyses electrical characteristics of rectangular and cylindrical
silicon nanowire transistors as well as a Double gate MOS FET. A
double gate, triple gate, and gate all around nano wires were studied
to investigate the impact of increasing the number of gates on the
control of the short channel effect which is important in nanoscale
devices. Also in the case of triple gate rectangular SNWT inserting
extra gates on the bottom of device can improve the application of
device. The results indicate that by using gate all around structures
short channel effects such as DIBL, subthreshold swing and delay
reduces.
Abstract: Series of tellurite glass of the system 78TeO2-10PbO-
10Li2O-(2-x)Nd2O3-xEr2O3, where x = 0.5, 1.0, 1.5 and 2.0 was
successfully been made. A study of upconversion luminescence of
the Nd3+/Er3+ co-doped tellurite glass has been carried out. From
Judd-Ofelt analysis, the experimental lifetime, exp. τ of the glass
serie are found higher in the visible region as they varies from
65.17ms to 114.63ms, whereas in the near infrared region (NIR) the
lifetime are varies from 2.133ms to 2.270ms. Meanwhile, the
emission cross section,σ results are found varies from 0.004 x 1020
cm2 to 1.007 x 1020 cm2 with respect to composition. The emission
spectra of the glass are found been contributed from Nd3+ and Er3+
ions by which nine significant transition peaks are observed. The
upconversion mechanism of the co-doped tellurite glass has been
shown in the schematic energy diagrams. In this works, it is found
that the excited state-absorption (ESA) is still dominant in the
upconversion excitation process as the upconversion excitation
mechanism of the Nd3+ excited-state levels is accomplished through a
stepwise multiphonon process. An efficient excitation energy transfer
(ET) has been observed between Nd3+ as a donor and Er3+ as the
acceptor. As a result, respective emission spectra had been observed.
Abstract: Following the loss of NASA's Space Shuttle
Columbia in 2003, it was determined that problems in the agency's
organization created an environment that led to the accident. One
component of the proposed solution resulted in the formation of the
NASA Engineering Network (NEN), a suite of information retrieval
and knowledge-sharing tools. This paper describes the
implementation of communities of practice, which are formed along
engineering disciplines. Communities of practice enable engineers to
leverage their knowledge and best practices to collaborate and take
information learning back to their jobs and embed it into the
procedures of the agency. This case study offers insight into using
traditional engineering disciplines for virtual collaboration, including
lessons learned during the creation and establishment of NASA-s
communities.
Abstract: To evaluate the ability to predict xerostomia after
radiotherapy, we constructed and compared neural network and
logistic regression models. In this study, 61 patients who completed a
questionnaire about their quality of life (QoL) before and after a full
course of radiation therapy were included. Based on this questionnaire,
some statistical data about the condition of the patients’ salivary
glands were obtained, and these subjects were included as the inputs of
the neural network and logistic regression models in order to predict
the probability of xerostomia. Seven variables were then selected from
the statistical data according to Cramer’s V and point-biserial
correlation values and were trained by each model to obtain the
respective outputs which were 0.88 and 0.89 for AUC, 9.20 and 7.65
for SSE, and 13.7% and 19.0% for MAPE, respectively. These
parameters demonstrate that both neural network and logistic
regression methods are effective for predicting conditions of parotid
glands.
Abstract: In this paper, Tobephobia (TBP) alludes to the fear of
failure experienced by teachers to manage curriculum change. TBP is
an emerging concept and it extends the boundaries of research in
terms of how we view achievement and failure in education.
Outcomes-based education (OBE) was introduced fifteen years ago
in South African schools without simultaneously upgrading teachers-
professional competencies. This exploratory research, therefore
examines a simple question: What is the impact of TBP and OBE on
teachers? Teacher ineptitude to cope with the OBE curriculum in the
classroom is a serious problem affecting large numbers of South
African teachers. This exploratory study sought to determine the
perceived negative impact of OBE and TBP on teachers. A survey
was conducted amongst 311 teachers in Port Elizabeth and Durban,
South Africa. The results confirm the very negative impact of TBP
and OBE on teachers. This exploratory study authenticates the
existence of TBP.
Abstract: Fructooligosaccharides derived from microbial enzyme especially from fungal sources has been received particular attention due to its beneficial effects as prebiotics and mass production. However, fungal fermentation is always cumbersome due to its broth rheology problem that will eventually affect the production of FOS. This study investigated the efficiency of immobilized cell system using rotating fibrous bed bioreactor (RFBB) in producing fructooligosaccharides (FOS). A comparative picture with respect to conventional stirred tank bioreactor (CSTB) and RFBB has been presented. To demonstrate the effect of agitation intensity and aeration rate, a laboratory-scale bioreactor 2.5 L was operated in three phases (high, medium, low) for 48 hours. Agitation speed has a great influence on P. simplicissimum fermentation for FOS production, where the volumetric FOS productivity using RFBB is increased with almost 4 fold compared to the FOS productivity in CSTB that only 0.319 g/L/h. Rate of FOS production increased up to 1.2 fold when immobilized cells system was employed at aeration rate similar to the freely suspended cells at 2.0 vvm.
Abstract: Rice, which is the staple food in Sierra Leone, is
consumed on a daily basis. It is the most imperative food crop
extensively grown by farmers across all ecologies in the country.
Though much attention is now given to rice grain production through
the small holder commercialization programme (SHCP), however, no
attention has been given in investigating the limitations faced by rice
producers. This paper will contribute to attempts to overcome the
development challenges caused by food insecurity. The objective of
this paper is thus, to analysis the relationship between rice production
and the domestic retail price of rice. The study employed a log linear
model in which, the quantity of rice produced is the dependent
variable, quantity of rice imported, price of imported rice and price of
domestic rice as explanatory variables. Findings showed that, locally
produced rice is even more expensive than the imported rice per ton,
and almost all the inhabitants in the capital city which hosts about
65% of the entire population of the country favor imported rice, as it
is free from stones with other impurities. On the other hand, to
control price and simultaneously increase rice production, the
government should purchase the rice from the farmers and then sell to private retailers.
Abstract: Cancers could normally be marked by a number of
differentially expressed genes which show enormous potential as
biomarkers for a certain disease. Recent years, cancer classification
based on the investigation of gene expression profiles derived by
high-throughput microarrays has widely been used. The selection of
discriminative genes is, therefore, an essential preprocess step in
carcinogenesis studies. In this paper, we have proposed a novel gene
selector using information-theoretic measures for biological
discovery. This multivariate filter is a four-stage framework through
the analyses of feature relevance, feature interdependence, feature
redundancy-dependence and subset rankings, and having been
examined on the colon cancer data set. Our experimental result show
that the proposed method outperformed other information theorem
based filters in all aspect of classification errors and classification
performance.
Abstract: In this study, active tendons with Proportional Integral
Derivation type controllers were applied to a SDOF and a MDOF
building model. Physical models of buildings were constituted with
virtual springs, dampers and rigid masses. After that, equations of
motion of all degrees of freedoms were obtained. Matlab Simulink
was utilized to obtain the block diagrams for these equations of
motion. Parameters for controller actions were found by using a trial
method. After earthquake acceleration data were applied to the
systems, building characteristics such as displacements, velocities,
accelerations and transfer functions were analyzed for all degrees of
freedoms. Comparisons on displacement vs. time, velocity vs. time,
acceleration vs. time and transfer function (Db) vs. frequency (Hz)
were made for uncontrolled and controlled buildings. The results
show that the method seems feasible.
Abstract: Current research has explored the impact of
instructional immediacy, defined as those behaviors that help build
close relationships or feelings of closeness, both on cognition and
motivation in the traditional classroom and online classroom;
however, online courses continue to suffer from higher dropout rates.
Based on Albert Bandura-s Social Cognitive Theory, four primary
relationships or interactions in an online course will be explored in
light of how they can provide immediacy thereby reducing student
attrition and improving cognitive learning. The four relationships are
teacher-student, student-student, and student-content, and studentcomputer.
Results of a study conducted with inservice teachers
completing a 14-week online professional development technology
course will be examined to demonstrate immediacy strategies that
improve cognitive learning and reduce student attrition. Results of
the study reveal that students can be motivated through various
interactions and instructional immediacy behaviors which lead to
higher completion rates, improved self-efficacy, and cognitive
learning.
Abstract: The interaction of the blade tip with the casing
boundary layer and the leakage flow may lead to a kind of cavitation
namely tip vortex cavitation. In this study, the onset of tip vortex
cavitation was experimentally investigated in an axial flow pump.
For a constant speed and a fixed angle of attack and by changing the
flow rate, the pump head, input power, output power and efficiency
were calculated and the pump characteristic curves were obtained.
The cavitation phenomenon was observed with a camera and a
stroboscope. Finally, the critical flow region, which tip vortex
cavitation might have occurred, was identified. The results show that
just by adjusting the flow rate, out of the specified region, the
possibility of occurring tip vortex cavitation, decreases to a great
extent.
Abstract: The common bean is the most important grain legume for direct human consumption in the world and BCMV is one of the world's most serious bean diseases that can reduce yield and quality of harvested product. To determine the best tolerance index to BCMV and recognize tolerant genotypes, 2 experiments were conducted in field conditions. Twenty five common bean genotypes were sown in 2 separate RCB design with 3 replications under contamination and non-contamination conditions. On the basis of the results of indices correlations GMP, MP and HARM were determined as the most suitable tolerance indices. The results of principle components analysis indicated 2 first components totally explained 98.52% of variations among data. The first and second components were named potential yield and stress susceptible respectively. Based on the results of BCMV tolerance indices assessment and biplot analysis WA8563-4, WA8563-2 and Cardinal were the genotypes that exhibited potential seed yield under contamination and noncontamination conditions.
Abstract: The number of framework conceived for e-learning
constantly increase, unfortunately the creators of learning materials
and educational institutions engaged in e-formation adopt a
“proprietor" approach, where the developed products (courses,
activities, exercises, etc.) can be exploited only in the framework
where they were conceived, their uses in the other learning
environments requires a greedy adaptation in terms of time and
effort. Each one proposes courses whose organization, contents,
modes of interaction and presentations are unique for all learners,
unfortunately the latter are heterogeneous and are not interested by
the same information, but only by services or documents adapted to
their needs. Currently the new tendency for the framework
conceived for e-learning, is the interoperability of learning materials,
several standards exist (DCMI (Dublin Core Metadata Initiative)[2],
LOM (Learning Objects Meta data)[1], SCORM (Shareable Content
Object Reference Model)[6][7][8], ARIADNE (Alliance of Remote
Instructional Authoring and Distribution Networks for Europe)[9],
CANCORE (Canadian Core Learning Resource Metadata
Application Profiles)[3]), they converge all to the idea of learning
objects. They are also interested in the adaptation of the learning
materials according to the learners- profile. This article proposes an
approach for the composition of courses adapted to the various
profiles (knowledge, preferences, objectives) of learners, based on
two ontologies (domain to teach and educational) and the learning
objects.
Abstract: Pakistani doctors (MBBS) are emigrating towards developed countries for professional adjustments. This study aims to highlight causes and consequences of doctors- brain drain from Pakistan. Primary data was collected from Mayo Hospital, Lahore by interviewing doctors (n=100) through systematic random sampling technique. It found that various socio-economic and political conditions are working as push and pull factors for brain drain of doctors in Pakistan. Majority of doctors (83%) declared poor remunerations and professional infrastructure of health department as push factor of doctors- brain drain. 81% claimed that continuous instability in political situation and threats of terrorism are responsible for emigration of doctors. 84% respondents considered fewer opportunities of further studies responsible for their emigration. Brain drain of doctors is affecting health sector-s policies / programs, standard doctor-patient ratios and quality of health services badly.
Abstract: It-s known that incorporating prior knowledge into support
vector regression (SVR) can help to improve the approximation
performance. Most of researches are concerned with the incorporation
of knowledge in the form of numerical relationships. Little work,
however, has been done to incorporate the prior knowledge on the
structural relationships among the variables (referred as to Structural
Prior Knowledge, SPK). This paper explores the incorporation of SPK
in SVR by constructing appropriate admissible support vector kernel
(SV kernel) based on the properties of reproducing kernel (R.K).
Three-levels specifications of SPK are studied with the corresponding
sub-levels of prior knowledge that can be considered for the method.
These include Hierarchical SPK (HSPK), Interactional SPK (ISPK)
consisting of independence, global and local interaction, Functional
SPK (FSPK) composed of exterior-FSPK and interior-FSPK. A
convenient tool for describing the SPK, namely Description Matrix
of SPK is introduced. Subsequently, a new SVR, namely Motivated
Support Vector Regression (MSVR) whose structure is motivated
in part by SPK, is proposed. Synthetic examples show that it is
possible to incorporate a wide variety of SPK and helpful to improve
the approximation performance in complex cases. The benefits of
MSVR are finally shown on a real-life military application, Air-toground
battle simulation, which shows great potential for MSVR to
the complex military applications.
Abstract: A new chelating resin is prepared by coupling Amberlite XAD-4 with 1-amino-2-naphthole through an azo spacer. The resulting sorbent has been characterized by FT-IR, elemental analysis and thermogravimetric analysis (TGA) and studied for preconcentrating of Fe (II) using flame atomic absorption spectrometry (FAAS) for metal monitoring. The optimum pH value for sorption of the iron ions was 6.5. The resin was subjected to evaluation through batch binding of mentioned metal ion. Quantitative desorption occurs instantaneously with 0.5 M HNO3. The sorption capacity was found 4.1 mmol.g-1 of resin for Fe (II) in the aqueous solution. The chelating resin can be reused for 10 cycles of sorption-desorption without any significant change in sorption capacity. A recovery of 97% was obtained the metal ions with 0.5 M HNO3 as eluting agent. The method was applied for metal ions determination from industrial waste water sample.
Abstract: Gold passbook is an investing tool that is especially
suitable for investors to do small investment in the solid gold. The gold
passbook has the lower risk than other ways investing in gold, but its
price is still affected by gold price. However, there are many factors
can cause influences on gold price. Therefore, building a model to
predict the price of gold passbook can both reduce the risk of
investment and increase the benefits. This study investigates the
important factors that influence the gold passbook price, and utilize
the Group Method of Data Handling (GMDH) to build the predictive
model. This method can not only obtain the significant variables but
also perform well in prediction. Finally, the significant variables of
gold passbook price, which can be predicted by GMDH, are US dollar
exchange rate, international petroleum price, unemployment rate,
whole sale price index, rediscount rate, foreign exchange reserves,
misery index, prosperity coincident index and industrial index.