Abstract: The Cone Penetration Test (CPT) is a common in-situ
test which generally investigates a much greater volume of soil more
quickly than possible from sampling and laboratory tests. Therefore,
it has the potential to realize both cost savings and assessment of soil
properties rapidly and continuously. The principle objective of this
paper is to demonstrate the feasibility and efficiency of using
artificial neural networks (ANNs) to predict the soil angle of internal
friction (Φ) and the soil modulus of elasticity (E) from CPT results
considering the uncertainties and non-linearities of the soil. In
addition, ANNs are used to study the influence of different
parameters and recommend which parameters should be included as
input parameters to improve the prediction. Neural networks discover
relationships in the input data sets through the iterative presentation
of the data and intrinsic mapping characteristics of neural topologies.
General Regression Neural Network (GRNN) is one of the powerful
neural network architectures which is utilized in this study. A large
amount of field and experimental data including CPT results, plate
load tests, direct shear box, grain size distribution and calculated data
of overburden pressure was obtained from a large project in the
United Arab Emirates. This data was used for the training and the
validation of the neural network. A comparison was made between
the obtained results from the ANN's approach, and some common
traditional correlations that predict Φ and E from CPT results with
respect to the actual results of the collected data. The results show
that the ANN is a very powerful tool. Very good agreement was
obtained between estimated results from ANN and actual measured
results with comparison to other correlations available in the
literature. The study recommends some easily available parameters
that should be included in the estimation of the soil properties to
improve the prediction models. It is shown that the use of friction
ration in the estimation of Φ and the use of fines content in the
estimation of E considerable improve the prediction models.
Abstract: The detection of the polymer melt state during
manufacture process is regarded as an efficient way to control the
molded part quality in advance. Online monitoring rheological
property of polymer melt during processing procedure provides an
approach to understand the melt state immediately. Rheological
property reflects the polymer melt state at different processing
parameters and is very important in injection molding process
especially. An approach that demonstrates how to calculate
rheological property of polymer melt through in-process
measurement, using injection molding as an example, is proposed in
this study. The system consists of two sensors and a data acquisition
module can process the measured data, which are used for the
calculation of rheological properties of polymer melt. The rheological
properties of polymer melt discussed in this study include shear rate
and viscosity which are investigated with respect to injection speed
and melt temperature. The results show that the effect of injection
speed on the rheological properties is apparent, especially for high
melt temperature and should be considered for precision molding
process.
Abstract: The aim of research was to define the relations
between volatile compounds, some parameters (pH, titratable acidity
(TA), total soluble solid (TSS), lactic acid bacteria count) and
consumer preference of commercial fermented milks. These relations
tend to be used for controlling and developing new fermented milk
product. Three leading commercial brands of fermented milks in
Thailand were evaluated by consumers (n=71) using hedonic scale
for four attributes (sweetness, sourness, flavour, and overall liking),
volatile compounds using headspace-solid phase microextraction
(HS-SPME) GC-MS, pH, TA, TSS and LAB count. Then the
relations were analyzed by principal component analysis (PCA). The
PCA data showed that all of four attributes liking scores were related
to each other. They were also related to TA, TSS and volatile
compounds. The related volatile compounds were mainly on
fermented produced compounds including acetic acid, furanmethanol,
furfural, octanoic acid and the volatiles known as artificial fruit
flavour (beta pinene, limonene, vanillin, and ethyl vanillin). These
compounds were provided the information about flavour addition in
commercial fermented milk in Thailand.
Abstract: In order to detect and quantify the phenolic contents
of a wastewater with biosensors, two working electrodes based on
modified Poly(Pyrrole) films were fabricated. Enzyme horseradish
peroxidase was used as biomolecule of the prepared electrodes.
Various phenolics were tested at the biosensor. Phenol detection was
realized by electrochemical reduction of quinones produced by
enzymatic activity. Analytical parameters were calculated and the
results were compared with each other.
Abstract: Fluid viscous damping systems are well suited for
many air vehicles subjected to shock and vibration. These damping
system work with the principle of viscous fluid throttling through the
orifice to create huge pressure difference between compression and
rebound chamber and obtain the required damping force. One
application of such systems is its use in aircraft door system to
counteract the door’s velocity and safely stop it. In exigency
situations like crash or emergency landing where the door doesn’t
open easily, possibly due to unusually tilting of fuselage or some
obstacles or intrusion of debris obstruction to move the parts of the
door, such system can be combined with other systems to provide
needed force to forcefully open the door and also securely stop it
simultaneously within the required time i.e. less than 8 seconds. In
the present study, a hydraulic system called snubber along with other
systems like actuator, gas bottle assembly which together known as
emergency power assist system (EPAS) is designed, built and
experimentally studied to check the magnitude of angular velocity,
damping force and time required to effectively open the door.
Whenever needed, the gas pressure from the bottle is released to
actuate the actuator and at the same time pull the snubber’s piston to
operate the emergency opening of the door. Such EPAS installed in
the suspension arm of the aircraft door is studied explicitly changing
parameters like orifice size, oil level, oil viscosity and bypass valve
gap and its spring of the snubber at varying temperature to generate
the optimum design case. Comparative analysis of the EPAS at
several cases is done and conclusions are made. It is found that
during emergency condition, the system opening time and angular
velocity, when snubber with 0.3mm piston and shaft orifice and
bypass valve gap of 0.5 mm with its original spring is used, shows
significant improvement over the old ones.
Abstract: The effects of basil and/or chamomile seed
supplementation on the growth of Hubbard broiler chicks were
evaluated. The antioxidant effects of these supplements were also
assessed. 120 1-day-old broiler chicks were randomly divided into
four equal groups. The control group (group 1) was fed a basal diet
(BD) without supplementation. Groups 2, 3, and 4 were fed the BD
supplemented with 10g basil, 10g chamomile, and 5g basil plus 5g
chamomile per kg of food, respectively. Basil supplementation alone
or in combination with chamomile non-significantly (P≥0.05)
increased final body weight (3.2% and 0.3%, respectively) and
weight gain (3.5% and 3.6%, respectively) over the experimental
period. Chamomile supplementation alone non-significantly (P≥0.05)
reduced final body weight and weight gain over the experimental
period by 1.7% and 1.7%, respectively. In comparison to the control
group, herbal seed supplementation reduced feed intake and
improved the feed conversion and protein efficiency ratios. In
general, basil seed supplementation stimulated chicken growth and
improved the feed efficiency more effectively than chamomile seed
supplementation. The antioxidant activities of basil and/or chamomile
supplementation were examined in the thymus, bursa, and spleen. In
chickens that received supplements, the level of malondialdehyde
was significantly decreased, whereas the activities of glutathione,
superoxide dismutase, and catalase were significantly increased
(P
Abstract: Artificial intelligence applications are commonly used
in industry in many fields in parallel with the developments in the
computer technology. In this study, a fire room was prepared for the
resistance of wooden construction elements and with the mechanism
here, the experiments of polished materials were carried out. By
utilizing from the experimental data, an artificial neural network
(ANN) was modelled in order to evaluate the final cross sections of
the wooden samples remaining from the fire. In modelling,
experimental data obtained from the fire room were used. In the
developed system, the first weight of samples (ws-gr), preliminary
cross-section (pcs-mm2), fire time (ft-minute), and fire temperature
(t-oC) as input parameters and final cross-section (fcs-mm2) as output
parameter were taken. When the results obtained from ANN and
experimental data are compared after making statistical analyses, the
data of two groups are determined to be coherent and seen to have no
meaning difference between them. As a result, it is seen that ANN
can be safely used in determining cross sections of wooden materials
after fire and it prevents many disadvantages.
Abstract: The pullout strength had an effect on the stability of
plate screw fixation when inserted in the cervical spine. Nine
different titanium alloy bone screws were used to test the pullout
strength through finite element analysis. The result showed that the
Moss Miami I can bear the highest pullout force at 1,075 N, which
causes the maximum von Mises stress at 858.87 MPa, a value over
the yield strength of titanium. The bone screw should have large
outer diameter, core diameter and proximal root radius to increase the
pullout strength.
Abstract: Many aluminum motorcycle parts produced by a high
pressure die casting. Some parts such as fuel caps were a thin and
complex shape. This part risked for porosities and blisters on surface
if it only depended on an experience of mold makers for mold design.
This research attempted to use CAST-DESIGNER software
simulated the high pressure die casting process with the same process
parameters of a motorcycle fuel cap production. The simulated results
were compared with fuel cap products and expressed the same
porosity and blister locations on cap surface. An average of absolute
difference of simulated results was obtained 0.094 mm when
compared the simulated porosity and blister defect sizes on the fuel
cap surfaces with the experimental micro photography. This
comparison confirmed an accuracy of software and will use the
setting parameters to improve fuel cap molds in the further work.
Abstract: A computational fluid dynamics (CFD) model is
developed for rechargeable non-aqueous electrolyte lithium-air
batteries with a partial opening for oxygen supply to the cathode.
Multi-phase transport phenomena occurred in the battery are
considered, including dissolved lithium ions and oxygen gas in the
liquid electrolyte, solid-phase electron transfer in the porous
functional materials and liquid-phase charge transport in the
electrolyte. These transport processes are coupled with the
electrochemical reactions at the active surfaces, and effects of
discharge reaction-generated solid Li2O2 on the transport properties
and the electrochemical reaction rate are evaluated and implemented
in the model. The predicted results are discussed and analyzed in terms
of the spatial and transient distribution of various parameters, such as
local oxygen concentration, reaction rate, variable solid Li2O2 volume
fraction and porosity, as well as the effective diffusion coefficients. It
is found that the effect of the solid Li2O2 product deposited at the solid
active surfaces is significant on the transport phenomena and the
overall battery performance.
Abstract: Estimation of model parameters is necessary to predict
the behavior of a system. Model parameters are estimated using
optimization criteria. Most algorithms use historical data to estimate
model parameters. The known target values (actual) and the output
produced by the model are compared. The differences between the
two form the basis to estimate the parameters. In order to compare
different models developed using the same data different criteria are
used. The data obtained for short scale projects are used here. We
consider software effort estimation problem using radial basis
function network. The accuracy comparison is made using various
existing criteria for one and two predictors. Then, we propose a new
criterion based on linear least squares for evaluation and compared
the results of one and two predictors. We have considered another
data set and evaluated prediction accuracy using the new criterion.
The new criterion is easy to comprehend compared to single statistic.
Although software effort estimation is considered, this method is
applicable for any modeling and prediction.
Abstract: Macro invertebrates have been used to monitor
organic pollution in rivers and streams. Several biotic indices based
on macro invertebrates have been developed over the years including
the Biological Monitoring Working Party (BMWP). A new biotic
index, the Gammarus:Asellus ratio has been recently proposed as an
index of organic pollution. This study tested the validity of the
Gammarus:Asellus ratio as an index of organic pollution, by
examining the relationship between the Gammarus:Asellus ratio and
physical chemical parameters, and other biotic indices such as
BMWP and, Average Score Per Taxon (ASPT) from lakes and
streams at Markeaton Park, Allestree Park and Kedleston Hall,
Derbyshire. Macro invertebrates were sampled using the standard
five minute kick sampling techniques physical and chemical
environmental variables were obtained based on standard sampling
techniques. Eighteen sites were sampled, six sites from Markeaton
Park (three sites across the stream and three sites across the lake). Six
sites each were also sampled from Allestree Park and Kedleston Hall
lakes. The Gammarus:Asellus ratio showed an opposite significant
positive correlations with parameters indicative of organic pollution
such as the level of nitrates, phosphates, and calcium and also
revealed a negatively significant correlations with other biotic indices
(BMWP/ASPT). The BMWP score correlated positively significantly
with some water quality parameters such as dissolved oxygen and
flow rate, but revealed no correlations with other chemical
environmental variables. The BMWP score was significantly higher
in the stream than the lake in Markeaton Park, also The ASPT scores
appear to be significantly higher in the upper Lakes than the middle
and lower lakes. This study has further strengthened the use of
BMWP/ASPT score as an index of organic pollution. But additional
application is required to validate the use of Gammarus:Asellus as a
rapid bio monitoring tool.
Abstract: The aim of this paper is to perform experimental
modal analysis (EMA) of reinforced concrete (RC) square slabs.
EMA is the process of determining the modal parameters (Natural
Frequencies, damping factors, modal vectors) of a structure from a
set of frequency response functions FRFs (curve fitting). Although,
experimental modal analysis (or modal testing) has grown steadily in
popularity since the advent of the digital FFT spectrum analyzer in
the early 1970’s, studying all types of members and materials using
such method have not yet been well documented. Therefore, in this
work, experimental tests were conducted on RC square slab
specimens of dimensions 600mm x 600mmx 40mm. Experimental
analysis was based on freely supported boundary condition.
Moreover, impact testing as a fast and economical means of finding
the modes of vibration of a structure was used during the
experiments. In addition, Pico Scope 6 device and MATLAB
software were used to acquire data, analyze and plot Frequency
Response Function (FRF). The experimental natural frequencies
which were extracted from measurements exhibit good agreement
with analytical predictions. It is showed that EMA method can be
usefully employed to investigate the dynamic behavior of RC slabs.
Abstract: To achieve reliable welds with minimum distortion for
the fabrication of components in aerospace industry laser beam
welding is attempted. Laser welding can provide a significant benefit
for the welding of Titanium and Aluminium thin sheet alloys of its
precision and rapid processing capability. For laser welding, pulse
shape, energy, duration, repetition rate and peak power are the most
important parameters that influence directly the quality of welds. In
this experimental work for joining 1mm thick TI6AL4V and AA2024
alloy and JK600 Nd:YAG pulsed laser units used. The distortions at
different welding power and speed of titanium and aluminium thin
sheet alloys are investigated. Test results reveal that increase in
welding speed increases distortion in weldment
Abstract: Elastomeric dielectric material has recently become a
new alternative for actuator technology. The characteristics of
dielectric elastomers placed between two electrodes to withstand
large strain when electrodes are charged has attracted the attention of
many researcher to study this material for actuator technology. Thus,
in the past few years Danfoss Ventures A/S has established their own
dielectric electro-active polymer (DEAP), which was called
PolyPower.
The main objective of this work was to investigate the dynamic
characteristics for vibration control of a PolyPower actuator folded in
‘pull’ configuration. A range of experiments was carried out on the
folded actuator including passive (without electrical load) and active
(with electrical load) testing. For both categories static and dynamic
testing have been done to determine the behavior of folded DEAP
actuator.
Voltage-Strain experiments show that the DEAP folded actuator is
a non-linear system. It is also shown that the voltage supplied has no
effect on the natural frequency. Finally, varying AC voltage with
different amplitude and frequency shows the parameters that
influence the performance of DEAP folded actuator. As a result, the
actuator performance dominated by the frequency dependence of the
elastic response and was less influenced by dielectric properties.
Abstract: The aim of this study is to evaluate the effects of the
laser and partial vibration stimulation on the mice tibia with
morphological characteristics. Twenty female C57BL/6 mice (12
weeks old) were used for the experiment. The study was carried out on
four groups of animals each consisting of five mice. Four groups of
mice were ovariectomized. Animals were scanned at 0 and 2 weeks
after ovariectomy by using micro computed tomography to estimate
morphological characteristics of tibial trabecular bone. Morphological
analysis showed that structural parameters of multi-stimuli group
appear significantly better phase in BV/TV, BS/BV, Tb.Th, Tb.N,
Tb.Sp, and Tb.pf than single stimulation groups. However, single
stimulation groups didn’t show significant effect on tibia with Sham
group. This study suggests that multi-stimuli may restrain the change
as the degenerate phase on osteoporosis in the mice tibia.
Abstract: Diffusion stills have been effective in water
desalination. The present work represents a model of the distillation
process by using vertical single-effect diffusion stills. A semianalytical
model has been developed to model the process. A
software computer code using Engineering Equation Solver EES
software has been developed to solve the equations of the developed
model. An experimental setup has been constructed, and used for the
validation of the model. The model is also validated against former
literature results. The results obtained from the present experimental
test rig, and the data from the literature, have been compared with the
results of the code to find its best range of validity. In addition, a
parametric analysis of the system has been developed using the
model to determine the effect of operating conditions on the system's
performance. The dominant parameters that affect the productivity of
the still are the hot plate temperature that ranges from (55- 90°C) and
feed flow rate in range of (0.00694-0.0211 kg/m2-s).
Abstract: Since columns are the most important elements of the
structures, failure of one column in a critical location can cause a
progressive collapse. In this respect, the repair and strengthening of
columns is a very important subject to reduce the building failure and
to keep the columns capacity. Twenty columns with different
parameters is tested and analysis. Eleven typical confined reinforced
concrete (RC) columns with different types of techniques are
assessment. And also, four confined concrete columns with plastic
tube (PVC) are tested with and with four paralleling tested of
unconfined plain concrete. The techniques of confined RC columns
are mortar strengthening, Steel rings strengthening, FRP
strengthening. Moreover, the technique of confined plain concrete
(PC) column is used PVC tubes. The columns are tested under
uniaxial compressive loads studied the effect of confinement on the
structural behavior of circular RC columns. Test results for each
column are presented in the form of crack patterns, stress-strain
curves. Test results show that confining of the RC columns using
different techniques of strengthening results significant improvement
of the general behavior of the columns and can used in construction.
And also, tested confined PC columns with PVC tubes results shown
that the confined PC with PVC tubes can be used in economical
building. The theoretical model for predicted column capacity is
founded with experimental factor depends on the confined techniques
used and the strain reduction.
Abstract: A compact UWB planar antenna fed with a
microstrip-line is proposed. The new design consist of a rectangular
patch with symmetric l-shaped slots and fed by 50 Ω microstrip
transmission line and a reduced ground-plane which have a periodic
slots with an overall size of 47 mm x 20 mm. It is intended to be used
in wireless applications that cover the ultra-wideband (UWB)
frequency band. A wider impedance bandwidth of around 116.5%
(1.875 – 7.115 GHz) with stable radiation pattern is achieved. The
proposed antenna has excellent characteristics, low profile and costeffective
compared to existing UWB antennas. The UWB antenna is
designed and analyzed using CST Microwave Studio in transient
mode to verify antenna parameters improvements.
Abstract: Ocimum americanum L (Lamiaceae) is an annual herb
that is native to tropical Africa. The in vitro and in vivo antioxidant
activity of its aqueous extract was carefully investigated by assessing
the DPPH radical scavenging activity, ABTS radical scavenging
activity and hydrogen peroxide radical scavenging activity. The
reducing power, total phenol, total flavonoids and flavonols content
of the extract were also evaluated. The data obtained revealed that the
extract is rich in polyphenolic compounds and scavenged the radicals
in a concentration dependent manner. This was done in comparison
with the standard antioxidants such as BHT and Vitamin C. Also, the
induction of oxidative damage with paracetamol (2000 mg/kg)
resulted in the elevation of lipid peroxides and significant (P < 0.05)
decrease in activities of superoxide dismutase, glutathione
peroxidase, glutathione reductase and catalase in the liver and kidney
of rats. However, the pretreatment of rats with aqueous extract of O.
americanum leaves (200 and 400 mg/kg) and silymarin (100 mg/kg)
caused a significant (P < 0.05) reduction in the values of lipid
peroxides and restored the levels of antioxidant parameters in these
organs. These findings suggest that the leaves of O. americanum have
potent antioxidant properties which may be responsible for its
acclaimed folkloric uses.