Abstract: The main aim of the presented experiments is to
improve behaviour of sandwich structures under dynamic loading,
such as crash or explosion. This paper describes experimental
investigation on the response of new advanced materials to low and
high velocity load. Blast wave energy absorbers were designed using
two types of porous lightweight raw particle materials based on
expanded glass and ceramics with dimensions of 0.5-1 mm,
combined with polymeric binder. The effect of binder amount on the
static and dynamic properties of designed materials was observed.
Prism shaped specimens were prepared and loaded to obtain physicomechanical
parameters – bulk density, compressive and flexural
strength under quasistatic load, the dynamic response was determined
using Split Hopkinson Pressure bar apparatus. Numerical
investigation of the material behaviour in sandwich structure was
performed using implicit/explicit solver LS-Dyna. As the last step,
the developed material was used as the interlayer of blast resistant
litter bin, and it´s functionality was verified by real field blast tests.
Abstract: Exact solution of an unsteady flow of elastico-viscous
fluid through a porous media in a tube of ellipsoidal cross section
under the influence of constant pressure gradient has been obtained in
this paper. Initially, the flow is generated by a constant pressure
gradient. After attaining the steady state, the pressure gradient is
suddenly withdrawn and the resulting fluid motion in a tube of
ellipsoidal cross section by taking into account of the porosity factor
of the bounding surface is investigated. The problem is solved in twostages
the first stage is a steady motion in tube under the influence of
a constant pressure gradient, the second stage concern with an
unsteady motion. The problem is solved employing separation of
variables technique. The results are expressed in terms of a nondimensional
porosity parameter (K) and elastico-viscosity parameter
(β), which depends on the Non-Newtonian coefficient. The flow
parameters are found to be identical with that of Newtonian case as
elastic-viscosity parameter tends to zero and porosity tends to
infinity. It is seen that the effect of elastico-viscosity parameter and
the porosity parameter of the bounding surface has significant effect
on the velocity parameter.
Abstract: The dissimilar joint between aluminum/titanium
alloys (Al 6082 and Ti G2) were successfully achieved by CO2 laser
welding with a single pass and without filler material using the
overlap joint design. Laser welding parameters ranges combinations
were experimentally determined using Taguchi approach with the
objective of producing welded joint with acceptable welding profile
and high quality of mechanical properties. In this study a joining of
dissimilar Al 6082 / Ti G2 was resulted in three distinct regions
fusion area in the weldment. These regions are studied in terms of its
microstructural characteristics and microhardness which are directly
affecting the welding quality.
The weld metal was mainly composed of martensite alpha prime.
In two different metals in the two different sides of joint HAZ, grain
growth was detected. The microhardness of the joint distribution also
has shown microhardness increasing in the HAZ of two base metals
and a varying microhardness in fusion zone.
Abstract: Comparing other methods of waste water treatment,
constructed wetlands are one of the most fascinating practices
because being a natural process they are eco-friendly have low
construction and maintenance cost and have considerable capability
of wastewater treatment. The current research was focused mainly on
comparison of Ranunculus muricatus and Typha latifolia as wetland
plants for domestic wastewater treatment by designing and
constructing efficient pilot scale horizontal subsurface flow
mesocosms. Parameters like chemical oxygen demand, biological
oxygen demand, phosphates, sulphates, nitrites, nitrates, and
pathogenic indicator microbes were studied continuously with
successive treatments. Treatment efficiency of the system increases
with passage of time and with increase in temperature. Efficiency of
T. latifolia planted setups in open environment was fairly good for
parameters like COD and BOD5 which was showing reduction up to
82.5% for COD and 82.6% for BOD5 while DO was increased up to
125%. Efficiency of R. muricatus vegetated setup was also good but
lowers than that of T. latifolia planted showing 80.95% removal of
COD and BOD5. Ranunculus muricatus was found effective in
reducing bacterial count in wastewater. Both macrophytes were
found promising in wastewater treatment.
Abstract: Cemented carbide balls are usually implemented in
industry under the environment of high speed, high temperature,
corrosiveness and strong collisions. However, its application is limited
due to high fabrication cost, processing efficiency and quality. A novel
eccentric lapping method with two rotatable lapping plates was
proposed in this paper. A mathematical model was constructed to
analyze the influence of each design parameter on this lapping method.
To validate this new lapping method, an orthogonal experiment was
conducted with cemented carbide balls (YG6). The simulation model
was verified and the optimal lapping parameters were derived. The
results show that the surface roundness of the balls reaches to 0.65um
from 2um in 1 hour using this lapping method. So, using this novel
lapping method, it can effectively improve the machining precision
and efficiency of cemented carbide balls.
Abstract: New physical insights into the nonlinear Lorenz
equations related to flow resistance is discussed in this work. The
chaotic dynamics related to Lorenz equations has been studied in
many papers, which is due to the sensitivity of Lorenz equations to
initial conditions and parameter uncertainties. However, the physical
implication arising from Lorenz equations about convectional motion
attracts little attention in the relevant literature. Therefore, as a first
step to understand the related fluid mechanics of convectional motion,
this paper derives the Lorenz equations again with different forced
conditions in the model. Simulation work of the modified Lorenz
equations without the viscosity or buoyancy force is discussed. The
time-domain simulation results may imply that the states of the
Lorenz equations are related to certain flow speed and flow resistance.
The flow speed of the underlying fluid system increases as the flow
resistance reduces. This observation would be helpful to analyze the
coupling effects of different fluid parameters in a convectional model
in future work.
Abstract: This work deals with parameter identification of
permanent magnet motors, a class of ac motor which is particularly
important in industrial automation due to characteristics like
applications high performance, are very attractive for applications
with limited space and reducing the need to eliminate because they
have reduced size and volume and can operate in a wide speed range,
without independent ventilation. By using experimental data and
genetic algorithm we have been able to extract values for both the
motor inductance and the electromechanical coupling constant, which
are then compared to measured and/or expected values.
Abstract: Humans are social mammals, of the primate order.
Our biology, our behaviour and our pathologies are unique to us. In
our desire to understand, reduce solitary confinement one source of
information is the many reports of social isolation of other social
mammals, especially primates. A behavioural study was conducted in
the department of pharmacology at Indira Gandhi Medical College,
Shimla in Himachalpradesh province in India using white albino
mice. Different behavioural parameters were observed by using open
field, tail suspension, tests for aggressive behaviour and social
interactions and the effect of isolation was studied. The results were
evaluated and the standard statistics were applied. The said study was
done to establish facts that isolation itself impairs social behaviour
and can lead to alcohol dependence as well as related drug
dependence.
Abstract: The mixed micellization of adiphenine hydrochloride (ADP) with 1-decyl-3-methylimidazolium chloride (C10mim.Cl), was investigated at different mole fractions and temperatures by surface tension measurements. The synergistic behavior (i.e., non-ideal behavior) for binary mixtures was explained by the deviation of critical micelle concentration (cmc) from ideal critical micelle concentration (cmc*), micellar mole fraction (Xim) from ideal micellar mole fraction (Xiideal), the values of interaction parameter (β) and activity coefficients (fi) (for both mixed micelles and mixed monolayer). The excess free energy (ΔGex) for the ADP- C10mim.Cl binary mixtures explain the stability of mixed micelles in comparison to micelles of pure ADP and C10mim.Cl. Interfacial parameters, i.e., Gibbs surface excess (Гmax), minimum head group area at air/ water
interface (Amin), and free energy of micellization (ΔG0m) were also evaluated for the systems.
Abstract: The present work analyses different parameters of end
milling to minimize the surface roughness for AISI D2 steel. D2 Steel
is generally used for stamping or forming dies, punches, forming
rolls, knives, slitters, shear blades, tools, scrap choppers, tyre
shredders etc. Surface roughness is one of the main indices that
determines the quality of machined products and is influenced by
various cutting parameters. In machining operations, achieving
desired surface quality by optimization of machining parameters, is a
challenging job. In case of mating components the surface roughness
become more essential and is influenced by the cutting parameters,
because, these quality structures are highly correlated and are
expected to be influenced directly or indirectly by the direct effect of
process parameters or their interactive effects (i.e. on process
environment). In this work, the effects of selected process parameters
on surface roughness and subsequent setting of parameters with the
levels have been accomplished by Taguchi’s parameter design
approach. The experiments have been performed as per the
combination of levels of different process parameters suggested by
L9 orthogonal array. Experimental investigation of the end milling of
AISI D2 steel with carbide tool by varying feed, speed and depth of
cut and the surface roughness has been measured using surface
roughness tester. Analyses of variance have been performed for mean
and signal-to-noise ratio to estimate the contribution of the different
process parameters on the process.
Abstract: This paper presents the results and findings from a
parametric study on the water surface elevation at upstream of bridge
constriction for subcritical flow. In this study, the influence of
Manning's Roughness Coefficient of main channel (nmc) and
floodplain (nfp), and bridge opening (b) flow rate (Q), contraction
(kcon) and expansion coefficients (kexp) were investigated on
backwater level. The DECK bridge models with different span widths
and without any pier were investigated within the two stage channel
having various roughness conditions. One of the most commonly
used commercial one-dimensional HEC-RAS model was used in this
parametric study. This study showed that the effects of main channel
roughness (nmc) and flow rate (Q) on the backwater level are much
higher than those of the floodplain roughness (nfp). Bridge opening
(b) with contraction (kcon) and expansion coefficients (kexp) have very
little effect on the backwater level within this range of parameters.
Abstract: The turbocharger and turbocharging have been the
inherent component of diesel engines, so that critical parameters of
such engines, as BSFC (Brake Specific Fuel Consumption) or
thermal efficiency, fuel consumption, BMEP (Brake Mean Effective
Pressure), the power density output and emission level have been
improved extensively. In general, the turbocharger can be considered
as the most complex component of diesel engines, because it has
closely interrelated turbomachinery concepts of the turbines and the
compressors to thermodynamic fundamentals of internal combustion
engines and stress analysis of all components.
In this paper, a waste gate for a conventional single stage radial
turbine is investigated by consideration of turbochargers operation
constrains and engine operation conditions, without any detail
designs in the turbine and the compressor. Amount of opening waste
gate which extended between the ranges of full opened and closed
valve, is demonstrated by limiting compressor boost pressure ratio.
Obtaining of an optimum point by regard above mentioned items is
surveyed by three linked meanline modeling programs together
which consist of Turbomatch®, Compal®, Rital® madules in concepts
NREC® respectively.
Abstract: The rhizome of Java grass, Cyperus rotundus was
extracted different organic polar and non-polar solvents and
performed the in vitro antiviral and immunostimulant activities
against White Spot Syndrome Virus (WSSV) and Vibrio harveyi
respectively. Based on the initial screening the ethyl acetate extract of
C. rotundus was strong activities and further it was purified through
silica column chromatography and the fractions were screened again
for antiviral and immunostimulant activity. Among the different
fractions screened against the WSSV and V. harveyi, the fractions, FIII
to FV had strong activities. In order to study the in vivo influence
of C. rotundus, the fractions (F-III to FV) were pooled and delivered
to the F. indicus through artificial feed for 30 days. After the feeding
trail the experimental and control diet fed F. indicus were challenged
with virulent WSSV and studied the survival, molecular diagnosis,
biochemical, haematological, and immunological parameters.
Surprisingly, the pooled fractions (F-IV to FVI) incorporated diets
helped to significantly (P
Abstract: The seismic responses of steel buildings with semirigid
post-tensioned connections (PC) are estimated and compared
with those of steel buildings with typical rigid (welded) connections
(RC). The comparison is made in terms of global and local response
parameters. The results indicate that the seismic responses in terms of
interstory shears, roof displacements, axial load and bending
moments are smaller for the buildings with PC connection. The
difference is larger for global than for local parameters, which in turn
varies from one column location to another. The reason for this
improved behavior is that the buildings with PC dissipate more
hysteretic energy than those with RC. In addition, unlike the case of
buildings with WC, for the PC structures the hysteretic energy is
mostly dissipated at the connections, which implies that structural
damage in beams and columns is not significant. According to these
results, steel buildings with PC are a viable option in high seismicity
areas because of their smaller response and self-centering connection
capacity as well as the fact that brittle failure is avoided.
Abstract: This work introduces a simple device designed to
perform in-situ direct shear and sinkage tests on granular materials
as sand, clays, or regolith. It consists of a box nested within a larger
box. Both have open bottoms, allowing them to be lowered into the
material. Afterwards, two rotating plates on opposite sides of the
outer box will rotate outwards in order to clear regolith on either
side, providing room for the inner box to move relative to the plates
and perform a shear test without the resistance of the surrounding
soil. From this test, Coulomb parameters, including cohesion and
internal friction angle, as well as, Bekker parameters can be inferred.
This device has been designed for a laboratory setting, but with few
modifications, could be put on the underside of a rover for use in
a remote location. The goal behind this work is to ultimately create
a compact, but accurate measuring tool to put onto a rover or any
kind of exploratory vehicle to test for regolith properties of celestial
bodies.
Abstract: Ti6Al4V alloy is highly used in the automotive and
aerospace industry due to its good machining characteristics. Micro
EDM drilling is commonly used to drill micro hole on extremely hard
material with very high depth to diameter ratio. In this study, the
parameters of micro-electrical discharge machining (EDM) in drilling
of Ti6Al4V alloy is optimized for higher machining accuracy with
less hole-dilation and hole taper ratio. The micro-EDM machining
parameters includes, peak current and pulse on time. Fuzzy analysis
was developed to evaluate the machining accuracy. The analysis
shows that hole-dilation and hole-taper ratio are increased with the
increasing of peak current and pulse on time. However, the surface
quality deteriorates as the peak current and pulse on time increase.
The combination that gives the optimum result for hole dilation is
medium peak current and short pulse on time. Meanwhile, the
optimum result for hole taper ratio is low peak current and short pulse
on time.
Abstract: Maize constitutes a major agrarian production for use
by the vast population but despite its economic importance; it has not
been produced to meet the economic needs of the country. Achieving
optimum yield in maize can meaningfully be supported by land
suitability analysis in order to guarantee self-sufficiency for future
production optimization. This study examines land suitability for
maize production through the analysis of the physicochemical
variations in soil properties and other land attributes over space using
a Geographic Information System (GIS) framework.
Physicochemical parameters of importance selected include slope,
landuse, physical and chemical properties of the soil, and climatic
variables. Landsat imagery was used to categorize the landuse,
Shuttle Radar Topographic Mapping (SRTM) generated the slope and
soil samples were analyzed for its physical and chemical components.
Suitability was categorized into highly, moderately and marginally
suitable based on Food and Agricultural Organisation (FAO)
classification, using the Analytical Hierarchy Process (AHP)
technique of GIS. This result can be used by small scale farmers for
efficient decision making in the allocation of land for maize
production.
Abstract: Analysis of the properties of coconut (Cocos nucifera)
and its oil was evaluated in this work using standard analytical
techniques. The analyses carried out include proximate composition
of the fruit, extraction of oil from the fruit using different process
parameters and physicochemical analysis of the extracted oil. The
results showed the percentage (%) moisture, crude lipid, crude
protein, ash and carbohydrate content of the coconut as 7.59, 55.15,
5.65, 7.35 and 19.51 respectively. The oil from the coconut fruit was
odourless and yellowish liquid at room temperature (30oC). The
treatment combinations used (leaching time, leaching temperature
and solute: solvent ratio) showed significant differences (P
Abstract: The aim of this work is to build a model based on
tissue characterization that is able to discriminate pathological and
non-pathological regions from three-phasic CT images. With our
research and based on a feature selection in different phases, we are
trying to design a neural network system with an optimal neuron
number in a hidden layer. Our approach consists of three steps:
feature selection, feature reduction, and classification. For each
region of interest (ROI), 6 distinct sets of texture features are
extracted such as: first order histogram parameters, absolute gradient,
run-length matrix, co-occurrence matrix, autoregressive model, and
wavelet, for a total of 270 texture features. When analyzing more
phases, we show that the injection of liquid cause changes to the high
relevant features in each region. Our results demonstrate that for
detecting HCC tumor phase 3 is the best one in most of the features
that we apply to the classification algorithm. The percentage of
detection between pathology and healthy classes, according to our
method, relates to first order histogram parameters with accuracy of
85% in phase 1, 95% in phase 2, and 95% in phase 3.
Abstract: The wide use of the Internet-based applications bring many challenges to the researchers to guarantee the continuity of the connections needed by the mobile hosts and provide reliable Internet access for them. One of proposed solutions by Internet Engineering Task Force (IETF) is to connect the local, multi-hop, and infrastructure-less Mobile Ad hoc Network (MANET) with Internet structure. This connection is done through multi-interface devices known as Internet Gateways. Many issues are related to this connection like gateway discovery, handoff, address auto-configuration and selecting the optimum gateway when multiple gateways exist. Many studies were done proposing gateway selection schemes with a single selection criterion or weighted multiple criteria. In this research, a review of some of these schemes is done showing the differences, the features, the challenges and the drawbacks of each of them.