Abstract: Aldehydes as secondary lipid oxidation products are highly specific to the oxidative degradation of particular polyunsaturated fatty acids present in foods. Gas chromatographic analysis of those volatile compounds has been widely used for monitoring of the deterioration of food products. Developed static headspace gas chromatography method using flame ionization detector (SHS GC FID) was applied to monitor the aldehydes present in processed foods such as bakery, meat and confectionary products.
Five selected aldehydes were determined in samples without any sample preparation, except grinding for bakery and meat products. SHS–GC analysis allows the separation of propanal, pentanal, hexanal, heptanal and octanal, within 15min. Aldehydes were quantified in fresh and stored samples, and the obtained range of aldehydes in crackers was 1.62±0.05 – 9.95±0.05mg/kg, in sausages 6.62±0.46 – 39.16±0.39mg/kg; and in cocoa spread cream 0.48±0.01 – 1.13±0.02mg/kg. Referring to the obtained results, the following can be concluded, proposed method is suitable for different types of samples, content of aldehydes varies depending on the type of a sample, and differs in fresh and stored samples of the same type.
Abstract: In Algeria, now, the oil pumping plants are fed with electric power by independent local sources. This type of feeding has many advantages (little climatic influence, independent operation). However it requires a qualified maintenance staff, a rather high frequency of maintenance and repair and additional fuel costs. Taking into account the increasing development of the national electric supply network (Sonelgaz), a real possibility of transfer of the local sources towards centralized sources appears.These latter cannot only be more economic but more reliable than the independent local sources as well. In order to carry out this transfer, it is necessary to work out an optimal strategy to rebuilding these networks taking in account the economic parameters and the indices of reliability.
Abstract: This paper describes the smart energy monitoring system with a wireless sensor network for monitoring of electrical usage in smart house. Proposed system is composed of wireless plugs and energy control wallpad server. The wireless plug integrates an AC power socket, a relay to switch the socket ON/OFF, a Hall effect sensor to sense current of load appliance and a Kmote. The Kmote is a wireless communication interface based on TinyOS. We evaluated wireless plug in a laboratory, analyzed and presented energy consumption data from electrical appliances for 3 months in home.
Abstract: The Lattice Boltzmann Method (LBM) with double populations is applied to solve the steady-state laminar natural convective heat transfer in a triangular cavity filled with water. The bottom wall is heated, the vertical wall is cooled, and the inclined wall is kept adiabatic. The buoyancy effect was modeled by applying the Boussinesq approximation to the momentum equation. The fluid velocity is determined by D2Q9 LBM and the energy equation is discritized by D2Q4 LBM to compute the temperature field. Comparisons with previously published work are performed and found to be in excellent agreement. Numerical results are obtained for a wide range of parameters: the Rayleigh number from to and the inclination angle from 0° to 360°. Flow and thermal fields were exhibited by means of streamlines and isotherms. It is observed that inclination angle can be used as a relevant parameter to control heat transfer in right-angled triangular enclosures.
Abstract: To offer a large variety of products while maintaining
low costs, high speed, and high quality in a mass customization
product development environment, platform based product
development has much benefit and usefulness in many industry fields.
This paper proposes a product configuration strategy by similarity
measure, incorporating the knowledge engineering principles such as
product information model, ontology engineering, and formal concept
analysis.
Abstract: A retrospective study was undertaken to record the
occurrence and pattern of fractures in small animals (dogs and cats)
from year 2005 to 2010. A total of 650 cases were presented in small
animal surgery unit out of which of 116 (dogs and cats) were
presented with history of fractures of different bones. A total of
17.8% (116/650) cases were of fractures which constituted dogs 67%
while cats were 23%. The majority of animals were intact. Trauma in
the form of road side accident was the principal cause of fractures in
dogs whereas as in cats it was fall from height. The ages of the
fractured dog ranged from 4 months to 12 years whereas in cat it was
from 4 weeks to 10 years. The femoral fractures represented 37.5%
and 25% respectively in dogs and cats. Diaphysis, distal metaphyseal
and supracondylar fractures were the most affected sites in dog and
cats. Tibial fracture in dogs and cats represented 21.5% and 10%
while humoral fractures were 7.9% and 14% in dogs and cats
respectively. Humoral condyler fractures were most commonly seen
in puppies aged 4 to 6 months. Fractured radius-ulna incidence was
19% and 14% in dogs and cats respectively. Other fractures recorded
were of lumbar vertebrae, mandible and metacarpals etc. The
management comprised of external and internal fixation in both the
species. The most common internal fixation technique employed was
Intramedullary fixation in long followed by other methods like stack
or cross pinning, wiring etc as per findings in the cases. The cast
bandage was used majorly as mean for external coaptation. The
paper discusses the outcome of the case as per the technique
employed.
Abstract: Nowadays, we are facing with network threats that
cause enormous damage to the Internet community day by day. In
this situation, more and more people try to prevent their network
security using some traditional mechanisms including firewall,
Intrusion Detection System, etc. Among them honeypot is a versatile
tool for a security practitioner, of course, they are tools that are meant
to be attacked or interacted with to more information about attackers,
their motives and tools. In this paper, we will describe usefulness of
low-interaction honeypot and high-interaction honeypot and
comparison between them. And then we propose hybrid honeypot
architecture that combines low and high -interaction honeypot to
mitigate the drawback. In this architecture, low-interaction honeypot
is used as a traffic filter. Activities like port scanning can be
effectively detected by low-interaction honeypot and stop there.
Traffic that cannot be handled by low-interaction honeypot is handed
over to high-interaction honeypot. In this case, low-interaction
honeypot is used as proxy whereas high-interaction honeypot offers
the optimal level realism. To prevent the high-interaction honeypot
from infections, containment environment (VMware) is used.
Abstract: A 1.2 V, 0.61 mA bias current, low noise amplifier
(LNA) suitable for low-power applications in the 2.4 GHz band is
presented. Circuit has been implemented, laid out and simulated using
a UMC 130 nm RF-CMOS process. The amplifier provides a 13.3 dB
power gain a noise figure NF< 2.28 dB and a 1-dB compression point
of -15.69 dBm, while dissipating 0.74 mW. Such performance make
this design suitable for wireless sensor networks applications such as
ZigBee.
Abstract: This paper presents a comparative analysis of a new
unsupervised PCA-based technique for steel plates texture segmentation
towards defect detection. The proposed scheme called Variance
Based Component Analysis or VBCA employs PCA for feature
extraction, applies a feature reduction algorithm based on variance of
eigenpictures and classifies the pixels as defective and normal. While
the classic PCA uses a clusterer like Kmeans for pixel clustering,
VBCA employs thresholding and some post processing operations to
label pixels as defective and normal. The experimental results show
that proposed algorithm called VBCA is 12.46% more accurate and
78.85% faster than the classic PCA.
Abstract: In this paper a novel method was presented for
evaluating the fabric pills using digital image processing techniques. This work provides a novel technique for
detecting pills and also measuring their heights, surfaces and
volumes. Surely, measuring the intensity of defects by human vision is an inaccurate method for quality control; as a result, this problem became a motivation for employing digital image processing techniques for detection of defects of fabric
surface. In the former works, the systems were just limited to measuring of the surface of defects, but in the presented
method the height and the volume of defects were also
measured, which leads to a more accurate quality control. An algorithm was developed to first, find pills and then measure their average intensity by using three criteria of height, surface
and volume. The results showed a meaningful relation
between the number of rotations and the quality of pilled fabrics.
Abstract: Mechanical and water transport properties of high
performance concrete (HPC) containing natural zeolite as partial
replacement of Portland cement are studied. Experimental results
show that in the investigated mixes the use of natural zeolite leads to
an increase of porosity, decrease of compressive strength and
increase of moisture diffusivity and water vapor diffusion coefficient,
as compared with the reference HPC. However, for the replacement
level up to 20% of the mass of Portland cement the concretes still
maintain their high performance character and exhibit acceptable
water transport properties. Therefore, natural zeolite can be
considered an environmental friendly binder with a potential to
replace a part of Portland cement in concrete in building industry.
Abstract: The 'wind-rain' house has a courtyard with glazed
roof, which allows more direct sunlight to come into indoor spaces
during the winter. The glazed roof can be partially opened or closed
and automatically controlled to provide natural ventilation in order to
adjust for indoor thermal conditions and the roof area can be shaded
by reflective insulation materials during the summer. Two field
studies for evaluating indoor thermal conditions of the two 'windrain'
houses have been carried out by author in 2009 and 2010.
Indoor and outdoor air temperature and relative humidity adjacent to
floor and ceiling of the two sample houses were continuously tested
at 15-minute intervals, 24 hours a day during the winter months.
Based on field study data, this study investigates relationships
between building design and indoor thermal condition of the 'windrain'
house to improve the future house design for building thermal
comfort and energy efficiency
Abstract: Knowledge about the magnetic quantities in a magnetic circuit is always of great interest. On the one hand, this information is needed for the simulation of a transformer. On the other hand, parameter studies are more reliable, if the magnetic quantities are derived from a well established model. One possibility to model the 3-phase transformer is by using a magnetic equivalent circuit (MEC). Though this is a well known system, it is often not an easy task to set up such a model for a large number of lumped elements which additionally includes the nonlinear characteristic of the magnetic material. Here we show the setup of a solver for a MEC and the results of the calculation in comparison to measurements taken. The equations of the MEC are based on a rearranged system of the nodal analysis. Thus it is possible to achieve a minimum number of equations, and a clear and simple structure. Hence, it is uncomplicated in its handling and it supports the iteration process. Additional helpful tasks are implemented within the solver to enhance the performance. The electric circuit is described by an electric equivalent circuit (EEC). Our results for the 3-phase transformer demonstrate the computational efficiency of the solver, and show the benefit of the application of a MEC.
Abstract: A theoretical study is conducted to design and explore
the effect of different parameters such as heat loads, the tube size of
piping system, wick thickness, porosity and hole size on the
performance and capability of a Loop Heat Pipe(LHP). This paper
presents a steady state model that describes the different phenomena
inside a LHP. Loop Heat Pipes(LHPs) are two-phase heat transfer
devices with capillary pumping of a working fluid. By their original
design comparing with heat pipes and special properties of the
capillary structure, they-re capable of transferring heat efficiency for
distances up to several meters at any orientation in the gravity field,
or to several meters in a horizontal position. This theoretical model is
described by different relations to satisfy important limits such as
capillary and nucleate boiling. An algorithm is developed to predict
the size of the LHP satisfying the limitations mentioned above for a
wide range of applied loads. Finally, to assess and evaluate the
algorithm and all the relations considered, we have used to design a
new kind of LHP to recover the heat from the exhaust of an actual
Gas Turbine. By finding the results, it showed that we can use the
LHP as a very high efficient device to recover the heat even in high
amount of loads(exhaust of a gas turbine). The sizes of all parts of the
LHP were obtained using the developed algorithm.
Abstract: Effective employee selection is a critical component
of a successful organization. Many important criteria for personnel
selection such as decision-making ability, adaptability, ambition, and
self-organization are naturally vague and imprecise to evaluate. The
rough sets theory (RST) as a new mathematical approach to
vagueness and uncertainty is a very well suited tool to deal with
qualitative data and various decision problems. This paper provides
conceptual, descriptive, and simulation results, concentrating chiefly
on human resources and personnel selection factors. The current
research derives certain decision rules which are able to facilitate
personnel selection and identifies several significant features based
on an empirical study conducted in an IT company in Iran.
Abstract: Switched-mode converters play now a significant role in
modern society. Their operation are often crucial in various electrical
applications affecting the every day life. Therefore, the quality of
the converters needs to be reliably verified. Recent studies have
shown that the converters can be fully characterized by a set of
frequency responses which can be efficiently used to validate the
proper operation of the converters. Consequently, several methods
have been proposed to measure the frequency responses fast and
accurately. Most often correlation-based techniques have been applied.
The presented measurement methods are highly sensitive to
external errors and system nonlinearities. This fact has been often
forgotten and the necessary uncertainty analysis of the measured
responses has been neglected. This paper presents a simple approach
to analyze the noise and nonlinearities in the frequency-response
measurements of switched-mode converters. Coherence analysis is
applied to form a confidence interval characterizing the noise and
nonlinearities involved in the measurements. The presented method is
verified by practical measurements from a high-frequency switchedmode
converter.
Abstract: Mostly the systems are dealing with time varying
signals. The Power efficiency can be achieved by adapting the system
activity according to the input signal variations. In this context
an adaptive rate filtering technique, based on the level crossing sampling
is devised. It adapts the sampling frequency and the filter order
by following the input signal local variations. Thus, it correlates the
processing activity with the signal variations. Interpolation is required
in the proposed technique. A drastic reduction in the interpolation
error is achieved by employing the symmetry during the interpolation
process. Processing error of the proposed technique is
calculated. The computational complexity of the proposed filtering
technique is deduced and compared to the classical one. Results
promise a significant gain of the computational efficiency and hence
of the power consumption.
Abstract: Producing companies aspire to high delivery
availability despite appearing disruptions. To ensure high delivery
availability safety stocksare required. Howeversafety stock leads to
additional capital commitment and compensates disruptions instead
of solving the reasons.The intention is to increase the stability in
production by configuring the production planning and control
systematically. Thus the safety stock can be reduced. The largest
proportion of inventory in producing companies is caused by batch
inventory, schedule deviations and variability of demand rates.These
reasons for high inventory levels can be reduced by configuring the
production planning and control specifically. Hence the inventory
level can be reduced. This is enabled by synchronizing the lot size
straightening the demand as well as optimizing the releasing order,
sequencing and capacity control.
Abstract: Soft topological spaces are considered as mathematical tools for dealing with uncertainties, and a fuzzy topological space is a special case of the soft topological space. The purpose of this paper is to study soft topological spaces. We introduce some new concepts in soft topological spaces such as soft first-countable spaces, soft second-countable spaces and soft separable spaces, and some basic properties of these concepts are explored.
Abstract: The values of managers and employees in organizations are phenomena that have captured the interest of researchers at large. Despite this attention, there continues to be a lack of agreement on what values are and how they influence individuals, or how they are constituted in individuals- mind. In this article content-based approach is presented as alternative reference frame for exploring values. In content-based approach human thinking in different contexts is set at the focal point. Differences in valuations can be explained through the information contents of mental representations. In addition to the information contents, attention is devoted to those cognitive processes through which mental representations of values are constructed. Such informational contents are in decisive role for understanding human behavior. By applying content-based analysis to an examination of values as mental representations, it is possible to reach a deeper to the motivational foundation of behaviors, such as decision making in organizational procedures, through understanding the structure and meanings of specific values at play.