Abstract: Main objective of this paper is to establish a link
between inertial forces of the bearings used in construction of wind
power plant and its behavior. Using bearings with lower inertial
forces has the immediate effect of decreasing inertia rotor system,
with significant results in increased energy efficiency, due to
decreased friction forces between rollers and raceways. The F.E.M.
analysis shows the appearance of uniform contact stress at the ends of
the rollers, demonstrated the necessity of production of low mass
bearings. Favorable results are expected in the economic field, by
reducing material consumption and by increasing the durability of
bearings. Using low mass bearings with hollow rollers instead of
solid rollers has an impact on working temperature, on vibrations and
noise which decrease. Implementation of types of hollow rollers of
cylindrical tubular type, instead of expensive rollers with logarithmic
profile, will bring significant inertial forces decrease with large
benefits in behavior of wind power plant.
Abstract: Effects of nicotine on pre-partum body weight and
preimplantation embryonic development has been reported
previously. Present study was conducted to determine the effects of
annatto (Bixa orellana)-derived delta-tocotrienol (TCT) (with
presence of 10% gamma-TCT isomer) on the nicotine-induced
reduction in body weight and 8-cell embryonic growth in mice.
Twenty-four 6-8 weeks old (23-25g) female balb/c mice were
randomly divided into four groups (G1-G4; n=6). Those groups were
subjected to the following treatments for 7 consecutive days: G1
(control) were gavaged with 0.1 ml tocopherol stripped corn oil. G2
was subcutaneously (s.c.) injected with 3 mg/kg/day of nicotine. G3
received concurrent treatment of nicotine (3 mg/kg/day) and 60
mg/kg/day of δ-TCT mixture (contains 90% delta & 10% gamma
isomers) and G4 was given 60 mg/kg/day of δ-TCT mixture alone.
Body weights were recorded daily during the treatment. On Day 8,
females were superovulated with 5 IU Pregnant Mare’s Serum
Gonadotropin (PMSG) for 48 hours followed with 5 IU human
Chorionic Gonadotropin (hCG) before mated with males at the ratio
of 1:1. Females were sacrificed by cervical dislocation for embryo
collection 48 hours post-coitum. Collected embryos were cultured in
vitro. Results showed that throughout Day 1 to Day 7, the body
weight of nicotine treated group (G2) was significantly lower
(p
Abstract: Industries produce millions of cubic meters of effluent
every year and the wastewater produced may be released into the
surrounding water bodies, treated on-site or at municipal treatment
plants. The determination of organic matter in the wastewater
generated is very important to avoid any negative effect on the
aquatic ecosystem. The scope of the present work is to assess the
physicochemical composition of the wastewater produced from one
of the brewery industry in South Africa. This is to estimate the
environmental impact of its discharge into the receiving water bodies
or the municipal treatment plant. The parameters monitored for the
quantitative analysis of brewery wastewater include biological
oxygen demand (BOD5), chemical oxygen demand (COD), total
suspended solids, volatile suspended solids, ammonia, total oxidized
nitrogen, nitrate, nitrite, phosphorus and alkalinity content. In
average, the COD concentration of the brewery effluent was 5340.97
mg/l with average pH values of 4.0 to 6.7. The BOD5 and the solids
content of the wastewater from the brewery industry were high. This
means that the effluent is very rich in organic content and its
discharge into the water bodies or the municipal treatment plant could
cause environmental pollution or damage the treatment plant. In
addition, there were variations in the wastewater composition
throughout the monitoring period. This might be as a result of
different activities that take place during the production process, as
well as the effects of peak period of beer production on the water
usage.
Abstract: The phytotoxicity of heavy metals can be expressed
on roots and visible part of plants and is characterized by molecular
and metabolic answers at various levels of organization of the whole
plant. The present study was undertaken on two varieties of broad
bean Vicia faba (Sidi Aïch and Super Aguadulce). The device was
mounted on a substrate prepared by mixing sand, soil and compost,
the substrate was artificially contaminated with three doses of lead
nitrate [Pb(NO3)2] 0, 500 and 1000 ppm. Our objective is to follow
the behavior of plant opposite the stress by evaluating the
physiological parameters. The results reveal a reduction in the
parameters of the productivity (chlorophyll and proteins production)
with an increase in the osmoregulators (soluble sugars and
proline).These results show that the production of broad bean is
strongly modified by the disturbance of its internal physiology under
lead exposure.
Abstract: The composite flour blend consisting of corn, pearl
millet, black gram and wheat bran in the ratio of 80:5:10:5 was taken
to prepare the extruded product and their effect on physical properties
of extrudate was studied. The extrusion process was conducted in
laboratory by using twin screw extruder. The physical characteristics
evaluated include lateral expansion, bulk density, water absorption
index, water solubility index, and rehydration ratio and moisture
retention. The Central Composite Rotatable Design (CCRD) was
used to decide the level of processing variables i.e. feed moisture
content (%), screw speed (rpm), and barrel temperature (oC) for the
experiment. The data obtained after extrusion process were analyzed
by using response surface methodology. A second order polynomial
model for the dependent variables was established to fit the
experimental data. The numerical optimization studies resulted in
127°C of barrel temperature, 246 rpm of screw speed, and 14.5% of
feed moisture as optimum variables to produce acceptable extruded
product. The responses predicted by the software for the optimum
process condition resulted in lateral expansion 126%, bulk density
0.28 g/cm3, water absorption index 4.10 g/g, water solubility index
39.90%, rehydration ratio 544% and moisture retention 11.90% with
75% desirability.
Abstract: The recent interest in alternative and renewable
energy systems results in increased installed capacity ratio of such
systems in total energy production of the world. Specifically, Wind
Energy Conversion Systems (WECS) draw significant attention
among possible alternative energy options, recently. On the contrary
of the positive points of penetrating WECS in all over the world in
terms of environment protection, energy independence of the
countries, etc., there are significant problems to be solved for the grid
connection of large scale WECS. The reactive power regulation,
voltage variation suppression, etc. can be presented as major issues to
be considered in this regard. Thus, this paper evaluates the
application of a Static VAr Compensator (SVC) unit for the reactive
power regulation and operation continuity of WECS during a fault
condition. The system is modeled employing the IEEE 13 node test
system. Thus, it is possible to evaluate the system performance with
an overall grid simulation model close to real grid systems. The
overall simulation model is developed in
MATLAB/Simulink/SimPowerSystems® environments and the
obtained results effectively match the target of the provided study.
Abstract: Coal tar is a liquid by-product of coal pyrolysis
processes. This liquid oil mixture contains various kinds of useful
compounds such as benzoic aromatic compounds and phenolic
compounds. These compounds are widely used as raw material for
insecticides, dyes, medicines, perfumes, coloring matters, and many
others. The coal tar was collected by pyrolysis process of coal
obtained from PT Kaltim Prima Coal and Arutmin-Kalimantan. The
experiments typically occurred at the atmospheric pressure in a
laboratory furnace at temperatures ranging from 300 to 550oC with a
heating rate of 10oC/min and a holding time of 1 hour at the pyrolysis
temperature. The Gas Chromatography-Mass Spectroscopy (GC-MS)
was used to analyze the coal tar components. The obtained coal tar
has the viscosity of 3.12 cp, the density of 2.78 g/cm3, the calorific
value of 11,048.44 cal/g, and the molecular weight of 222.67. The
analysis result showed that the coal tar contained more than 78
chemical compounds such as benzene, cresol, phenol, xylene,
naphtalene, etc. The total phenolic compounds contained in coal tar
are 33.25% (PT KPC) and 17.58% (Arutmin-Kalimantan). The total
naphtalene compounds contained in coal tar is 14.15% (PT KPC) and
17.13% (Arutmin-Kalimantan).
Abstract: The spindle system is one of the most important
components of machine tool. The dynamic properties of the spindle
affect the machining productivity and quality of the work pieces.
Thus, it is important and necessary to determine its dynamic
characteristics of spindles in the design and development in order to
avoid forced resonance. The finite element method (FEM) has been
adopted in order to obtain the dynamic behavior of spindle system.
For this reason, obtaining the Campbell diagrams and determining the
critical speeds are very useful to evaluate the spindle system
dynamics. The unbalance response of the system to the center of
mass unbalance at the cutting tool is also calculated to investigate the
dynamic behavior. In this paper, we used an ANSYS Parametric
Design Language (APDL) program which based on finite element
method has been implemented to make the full dynamic analysis and
evaluation of the results. Results show that the calculated critical
speeds are far from the operating speed range of the spindle, thus, the
spindle would not experience resonance, and the maximum
unbalance response at operating speed is still with acceptable limit.
ANSYS Parametric Design Language (APDL) can be used by spindle
designer as tools in order to increase the product quality, reducing
cost, and time consuming in the design and development stages.
Abstract: Different designs of attenuator systems have been
studied in this research; new analysis have been done on existed
designs considering fibers effect on air flow; it was comprehended
that, at fibers presence, there is an air flow which agglomerates fibers
as a negative effect. So some new representations have been designed
and CFD analysis has been done on them. Afterwards, one of these
representations selected as the most optimum and effective design
which is brought in this paper.
Abstract: Tannase (tannin acyl hydrolase, E.C.3.1.1.20) is an
important hydrolysable enzyme with innumerable applications and
industrial potential. In the present study, a kinetic model has been
developed for the batch fermentation used for the production of
tannase by A.flavus MTCC 3783. Maximum tannase activity of
143.30 U/ml was obtained at 96 hours under optimum operating
conditions at 35oC, an initial pH of 5.5 and with an inducer tannic
acid concentration of 3% (w/v) for a fermentation period of 120
hours. The biomass concentration reaches a maximum of 6.62 g/l at
96 hours and further there was no increase in biomass concentration
till the end of the fermentation. Various unstructured kinetic models
were analyzed to simulate the experimental values of microbial
growth, tannase activity and substrate concentration. The Logistic
model for microbial growth , Luedeking - Piret model for production
of tannase and Substrate utilization kinetic model for utilization of
substrate were capable of predicting the fermentation profile with
high coefficient of determination (R2) values of 0.980, 0.942 and
0.983 respectively. The results indicated that the unstructured models
were able to describe the fermentation kinetics more effectively.
Abstract: Life cycle assessment is a technique to assess the
environmental aspects and potential impacts associated with a
product, process, or service, by compiling an inventory of relevant
energy and material inputs and environmental releases; evaluating the
potential environmental impacts associated with identified inputs and
releases; and interpreting the results to help you make a more
informed decision. In this paper, the life cycle assessment of
aluminum and beech wood as two commonly used materials in Egypt
for window frames are heading, highlighting their benefits and
weaknesses. Window frames of the two materials have been assessed
on the basis of their production, energy consumption and
environmental impacts. It has been found that the climate change of
the windows made of aluminum and beech wood window, for a
reference window (1.2m×1.2m), are 81.7 mPt and -52.5 mPt impacts
respectively. Among the most important results are: fossil fuel
consumption, potential contributions to the green building effect and
quantities of solid waste tend to be minor for wood products
compared to aluminum products; incineration of wood products can
cause higher impacts of acidification and eutrophication than
aluminum, whereas thermal energy can be recovered.
Abstract: In this paper comprehensive studies have been carried
out for the design optimization of a waste heat recovery system for
effectively utilizing the domestic air conditioner heat energy for
producing hot water. Numerical studies have been carried for the
geometry optimization of a waste heat recovery system for domestic
air conditioners. Numerical computations have been carried out using
a validated 2d pressure based, unsteady, 2nd-order implicit, SST k-ω
turbulence model. In the numerical study, a fully implicit finite
volume scheme of the compressible, Reynolds-Averaged, Navier-
Stokes equations is employed. At identical inflow and boundary
conditions various geometries were tried and effort has been taken for
proposing the best design criteria. Several combinations of pipe line
shapes viz., straight and spiral with different number of coils for the
radiator have been attempted and accordingly the design criteria has
been proposed for the waste heat recovery system design. We have
concluded that, within the given envelope, the geometry optimization
is a meaningful objective for getting better performance of waste heat
recovery system for air conditioners.
Abstract: Tool, Die and Mould-making (TDM) firms have been
known to play a pivotal role in the growth and development of the
manufacturing sectors in most economies. Their output contributes
significantly to the quality, cost and delivery speed of final
manufactured parts. Unfortunately, the South African Tool, Die and
Mould-making manufacturers have not been competing on the local
or global market in a significant way. This reality has hampered the
productivity and growth of the sector thus attracting intervention. The
paper explores the shortcomings South African toolmakers have to
overcome to restore their competitive position globally. Results from
a global benchmarking survey on the tooling sector are used to
establish a roadmap of what South African toolmakers can do to
become a productive, World Class force on the global market.
Abstract: A lower consumption of thermal energy will
contribute not only to a reduction in the running costs, but also in the
reduction of pollutant emissions that contribute to the greenhouse
effect. Cogeneration or CHP (Combined Heat and Power) is the
system that produces power and usable heat simultaneously by
decreasing the pollutant emissions and increasing the efficiency.
Combined production of mechanical or electrical and thermal energy
using a simple energy source, such as oil, coal, natural or liquefied
gas, biomass or the sun; affords remarkable energy savings and
frequently makes it possible to operate with greater efficiency when
compared to a system producing heat and power separately. This
study aims to bring out the contributions of cogeneration systems to
the environment and sustainability by saving the energy and reducing
the emissions. In this way we made a comprehensive investigation in
the literature by focusing on the environmental aspects of the
cogeneration systems. In the light of these studies we reached that,
cogeneration systems must be consider in sustainability and their
benefits on protecting the ecology must be investigated.
Abstract: Chalcopyrite (CuFeS2) is the most common primary
mineral used for the commercial production of copper. The low
dissolution efficiency of chalcopyrite in sulfate media has prevented
an efficient industrial leaching of this mineral in sulfate media. Ferric
ions, bacteria, oxygen and other oxidants have been used as oxidizing
agents in the leaching of chalcopyrite in sulfate and chloride media
under atmospheric or pressure leaching conditions. Two leaching
methods were studied to evaluate chalcopyrite (CuFeS2) dissolution
in acid media. First, the conventional oxidative acid leaching method
was carried out using sulfuric acid (H2SO4) and potassium
dichromate (K2Cr2O7) as oxidant at atmospheric pressure. Second,
microwave-assisted acid leaching was performed using the
microwave accelerated reaction system (MARS) for same reaction
media. Parameters affecting the copper extraction such as leaching
time, leaching temperature, concentration of H2SO4 and
concentration of K2Cr2O7 were investigated. The results of
conventional acid leaching experiments were compared to the
microwave leaching method. It was found that the copper extraction
obtained under high temperature and high concentrations of oxidant
with microwave leaching is higher than those obtained
conventionally. 81% copper extraction was obtained by the
conventional oxidative acid leaching method in 180 min, with the
concentration of 0.3 mol/L K2Cr2O7 in 0.5M H2SO4 at 50 ºC, while
93.5% copper extraction was obtained in 60 min with microwave
leaching method under same conditions.
Abstract: The design of Reverse logistics Network has attracted
growing attention with the stringent pressures from both
environmental awareness and business sustainability. Reverse
logistical activities include return, remanufacture, disassemble and
dispose of products can be quite complex to manage. In addition,
demand can be difficult to predict, and decision making is one of the
challenges task in such network. This complexity has amplified the
need to develop an integrated architecture for product return as an
enterprise system. The main purpose of this paper is to design Multi
Agent System (MAS) architecture using the Prometheus
methodology to efficiently manage reverse logistics processes. The
proposed MAS architecture includes five types of agents: Gate
keeping Agent, Collection Agent, Sorting Agent, Processing Agent
and Disposal Agent which act respectively during the five steps of
reverse logistics Network.
Abstract: Application of biochar to arable soils represents a new
approach to restore soil health and quality. Many studies reported the
positive effect of biochar application on soil fertility and
development of soil microbial community. Moreover biochar may
affect the soil water retention, but this effect has not been sufficiently
described yet. Therefore this study deals with the influence of
biochar application on: microbial activities in soil, availability of
mineral nitrogen in soil for microorganisms, mineral nitrogen
retention and plant production. To demonstrate the effect of biochar
addition on the above parameters, the pot experiment was realized.
As a model crop, Lactuca sativa L. was used and cultivated from
December 10th 2014 till March 22th 2015 in climate chamber in
thoroughly homogenized arable soil with and without addition of
biochar. Five variants of experiment (V1 – V5) with different regime
of irrigation were prepared. Variants V1 – V2 were fertilized by
mineral nitrogen, V3 – V4 by biochar and V5 was a control. The
significant differences were found only in plant production and
mineral nitrogen retention. The highest content of mineral nitrogen
in soil was detected in V1 and V2, about 250 % in comparison with
the other variants. The positive effect of biochar application on soil
fertility, mineral nitrogen availability was not found. On the other
hand results of plant production indicate the possible positive effect
of biochar application on soil water retention.
Abstract: ANDASA is a knowledge management platform for
the capitalization of knowledge and cultural assets for the artistic and
cultural sectors. It was built based on the priorities expressed by the
participating artists. Through mapping artistic activities and
specificities, it enables to highlight various aspects of the artistic
research and production. Such instrument will contribute to create
networks and partnerships, as it enables to evidentiate who does
what, in what field, using which methodology. The platform is
accessible to network participants and to the general public.
Abstract: Experiential marketing is one of the marketing
approaches that offer an exceptional framework to integrate elements
of experience and entertainment in a product or service. Experiential
marketing is defined as a memorable experience that goes deeply into
the customer’s mind. Besides that, customer satisfaction is defined as
an emotional response to the experiences provided by and associated
with particular products or services purchased. Thus, experiential
marketing activities can affect the level of customer satisfaction and
loyalty. In this context, the research aims to explore the relationship
among experiential marketing, customer satisfaction and customer
loyalty among the cosmetic products customers in Konya. The partial
least squares (PLS) method is used to analyze the survey data.
Findings of the present study revealed that experiential marketing has
been a significant predictor of customer satisfaction and customer
loyalty, and also experiential marketing has a significantly positive
effect on customer satisfaction and customer loyalty.
Abstract: Crops diversity and maintaining and enhancing the
fertility of agricultural lands are basic principles of organic farming.
With a wider range of crops in agroecosystem can improve the ability
to control weeds, pests and diseases, and the performance of crops
rotation and food safety. In this sense, the main objective of the
research was to study the productivity and chemical composition of
some alternative crops and their adaptability to soil and climatic
conditions of the agricultural area in Southern Romania and to
cultivation in the organic farming system. The alternative crops were:
lentil (7 genotypes); five species of grain legumes (5 genotypes); four
species of oil crops (5 genotypes). The seed production was, on
average: 1343 kg/ha of lentil; 2500 kg/ha of field beans; 2400 kg/ha
of chick peas and blackeyed peas; more than 2000 kg/ha of atzuki
beans, over 1250 kg/ha of fenugreek; 2200 kg/ha of safflower; 570
kg/ha of oil pumpkin; 2150 kg/ha of oil flax; 1518 kg/ha of camelina.
Regarding chemical composition, lentil seeds contained: 22.18%
proteins, 3.03% lipids, 33.29% glucides, 4.00% minerals, and 259.97
kcal energy values. For field beans: 21.50% proteins, 4.40% lipids,
63.90% glucides, 5.85% minerals, 395.36 kcal energetic value. For
chick peas: 21.23% proteins, 4.55% lipids, 53.00% glucides, 3.67%
minerals, 348.22 kcal energetic value. For blackeyed peas: 23.30%
proteins, 2.10% lipids, 68.10% glucides, 3.93% minerals, 350.14 kcal
energetic value. For adzuki beans: 21.90% proteins, 2.60% lipids,
69.30% glucides, 4.10% minerals, 402.48 kcal energetic value. For
fenugreek: 21.30% proteins, 4.65% lipids, 63.83% glucides, 5.69%
minerals, 396.54 kcal energetic value. For safflower: 12.60%
proteins, 28.37% lipids, 46.41% glucides, 3.60% minerals, 505.78
kcal energetic value. For camelina: 20.29% proteins, 31.68% lipids,
36.28% glucides, 4.29% minerals, 526.63 kcal energetic value. For
oil pumpkin: 29.50% proteins, 36.92% lipids, 18.50% glucides,
5.41% minerals, 540.15 kcal energetic value. For oil flax: 22.56%
proteins, 34.10% lipids, 27.73% glucides, 5.25% minerals, 558.45
kcal energetic value.