Abstract: Water 2H NMR signal on the surface of nano-silica material, MCM-41, consists of two overlapping resonances. The 2H water spectrum shows a superposition of a Lorentzian line shape and the familiar NMR powder pattern line shape, indicating the existence of two spin components. Chemical exchange occurs between these two groups. Decomposition of the two signals is a crucial starting point for study the exchange process. In this article we have determined these spin component populations along with other important parameters for the 2H water NMR signal over a temperature range between 223 K and 343 K.
Abstract: This paper proposes a Fuzzy Expert System design to
determine the wearing properties of nitrided and non nitrided steel.
The proposed Fuzzy Expert System approach helps the user and the
manufacturer to forecast the wearing properties of nitrided and non
nitrided steel under specified laboratory conditions. Surfaces of the
engineering components are often nitrided for improving wear,
corosion, fatigue specifications. A major property of nitriding
process is reducing distortion and wearing of the metalic alloys. A
Fuzzy Expert System was developed for determining the wearing and
durability properties of nitrided and non nitrided steels that were
tested under different loads and different sliding speeds in the
laboratory conditions.
Abstract: Aluminum salt that is generally presents as a solid
phase in the water purification sludge (WPS) can be dissolved,
recovering a liquid phase, by adding strong acid to the sludge solution.
According to the reaction kinetics, when reactant is in the form of
small particles with a large specific surface area, or when the reaction
temperature is high, the quantity of dissolved aluminum salt or
reaction rate, respectively are high. Therefore, in this investigation,
water purification sludge (WPS) solution was treated with ultrasonic
waves to break down the sludge, and different acids (1 N HCl and 1 N
H2SO4) were used to acidify it. Acid dosages that yielded the solution
pH of less than two were used. The results thus obtained indicate that
the quantity of dissolved aluminum in H2SO4-acidified solution
exceeded that in HCl-acidified solution. Additionally, ultrasonic
treatment increased the rate of dissolution of aluminum and the
amount dissolved. The quantity of aluminum dissolved at 60℃ was 1.5
to 2.0 times higher than that at 25℃.
Abstract: In this experimental study, performance of a counter
flow Ranque-Hilsch vortex tube (RHVT) with threads cut on its inner
surface was investigated experimentally (pitch is 1 and 2 mm). The
inner diameter of the vortex tube used was D=9 mm and the ratio of
the tube’s length to diameter was L/D=12. The experimental system
was a thermodynamic open system. Flow was controlled by a valve
on the hot outlet side, where the valve was changed from a nearly
closed position to its nearly open position. Fraction of cold flow (ξ) =
0.1-0.9, was determined under 300 and 350 kPa pressurized air. All
experimental data were compared with each other, the maximum
heating performance of the RHVT system was found to be 38.2 oC
and the maximum cooling performance of the RHVT in this study
was found to be -30.9 oC at pitch 1 mm.
Abstract: Polymer-like organic thin films were deposited on both
aluminum alloy type 6061 and glass substrates at room temperature by
Plasma Enhanced Chemical Vapor Deposition (PECVD) methodusing
benzene and hexamethyldisiloxane (HMDSO) as precursor materials.
The surface and physical properties of plasma-polymerized organic
thin films were investigated at different r.f. powers. The effects of
benzene/argon ratio on the properties of plasma polymerized benzene
films were also investigated. It is found that using benzene alone
results in a non-coherent and non-adherent powdery deposited
material. The chemical structure and surface properties of the asgrown
plasma polymerized thin films were analyzed on glass
substrates with FTIR and contact angle measurements. FTIR spectra
of benzene deposited film indicated that the benzene rings are
preserved when increasing benzene ratio and/or decreasing r.f.
powers. FTIR spectra of HMDSO deposited films indicated an
increase of the hydrogen concentration and a decrease of the oxygen
concentration with the increase of r.f. power. The contact angle (θ) of
the films prepared from benzene was found to increase by about 43%
as benzene ratio increases from 10% to 20%. θ was then found to
decrease to the original value (51°) when the benzene ratio increases
to 100%. The contact angle, θ, for both benzene and HMDSO
deposited films were found to increase with r.f. power. This signifies
that the plasma polymerized organic films have substantially low
surface energy as the r.f power increases. The corrosion resistance of
aluminum alloy substrate both bare and covered with plasma
polymerized thin films was carried out by potentiodynamic
polarization measurements in standard 3.5 wt. % NaCl solution at
room temperature. The results indicate that the benzene and HMDSO
deposited films are suitable for protection of the aluminum substrate
against corrosion. The changes in the processing parameters seem to
have a strong influence on the film protective ability. Surface
roughness of films deposited on aluminum alloy substrate was
investigated using scanning electron microscopy (SEM). The SEM
images indicate that the surface roughness of benzene deposited films
increase with decreasing the benzene ratio. SEM images of benzene
and HMDSO deposited films indicate that the surface roughness
decreases with increasing r.f. power. Studying the above parameters
indicate that the films produced are suitable for specific practical
applications.
Abstract: Soursop (Anona muricata) is one of the underutilized tropical fruits containing nutrients, particularly dietary fibre and antioxidant properties that are beneficial to human health. This objective of this study is to investigate the feasibility of matured soursop pulp flour (SPF) to be substituted with high-protein wheat flour in bread. Bread formulation was substituted with different levels of SPF (0%, 5%, 10% and 15%). The effect on physicochemical properties and sensory attributes were evaluated. Higher substitution level of SPF resulted in significantly higher (p
Abstract: Fossil fuels are the major source to meet the world
energy requirements but its rapidly diminishing rate and adverse
effects on our ecological system are of major concern. Renewable
energy utilization is the need of time to meet the future challenges.
Ocean energy is the one of these promising energy resources. Threefourths
of the earth-s surface is covered by the oceans. This enormous
energy resource is contained in the oceans- waters, the air above the
oceans, and the land beneath them. The renewable energy source of
ocean mainly is contained in waves, ocean current and offshore solar
energy. Very fewer efforts have been made to harness this reliable
and predictable resource. Harnessing of ocean energy needs detail
knowledge of underlying mathematical governing equation and their
analysis. With the advent of extra ordinary computational resources
it is now possible to predict the wave climatology in lab simulation.
Several techniques have been developed mostly stem from numerical
analysis of Navier Stokes equations. This paper presents a brief over
view of such mathematical model and tools to understand and
analyze the wave climatology. Models of 1st, 2nd and 3rd generations
have been developed to estimate the wave characteristics to assess the
power potential. A brief overview of available wave energy
technologies is also given. A novel concept of on-shore wave energy
extraction method is also presented at the end. The concept is based
upon total energy conservation, where energy of wave is transferred
to the flexible converter to increase its kinetic energy. Squeezing
action by the external pressure on the converter body results in
increase velocities at discharge section. High velocity head then can
be used for energy storage or for direct utility of power generation.
This converter utilizes the both potential and kinetic energy of the
waves and designed for on-shore or near-shore application. Increased
wave height at the shore due to shoaling effects increases the
potential energy of the waves which is converted to renewable
energy. This approach will result in economic wave energy
converter due to near shore installation and more dense waves due to
shoaling. Method will be more efficient because of tapping both
potential and kinetic energy of the waves.
Abstract: This paper deals with the design of a moving sliding
surface in a variable structure plant for a second order system. The
chattering phenomena is also dealt with during the switching process
for an unstable sliding surface condition. The simulation examples
considered in this paper shows the effectiveness of the sliding mode
control method used for the design of the moving sliding surfaces. A
simulink model of the continuous system was also developed in
MATLAB-SIMULINK for the design and hence demonstrated. The
phase portraits and the state plots shows the demonstration of
the powerful control technique which can be applied for second
order systems.
Abstract: Three dimensional nanostructure materials have attracted the attention of many researches because the possibility to apply them for near future devices in sensors, catalysis and energy related. Tin dioxide is the most used material for gas sensing because its three-dimensional nanostructures and properties are related to the large surface exposed to gas adsorption. We propose the use of branch SnO2 nanowhiskers in interaction with ethanol. All Sn atoms are symmetric. The total energy, potential energy and Kinetic energy calculated for interaction between SnO2 and ethanol in different distances and temperatures. The calculations achieved by methods of Langevin Dynamic and Mont Carlo simulation. The total energy increased with addition ethanol molecules and temperature so interactions between them are endothermic.
Abstract: The purpose of this research was to analyze and compare the instability of a contact surface between Copper and Nickel an alloy cathode in vacuum, the different ratio of Copper and Copper were conducted at 1%, 2% and 4% by using the cathode spot model. The transient recovery voltage is predicted. The cathode spot region is recognized as the collisionless space charge sheath connected with singly ionized collisional plasma. It was found that the transient voltage is decreased with increasing the percentage of an amount of Nickel in cathode materials.
Abstract: Minimum Quantity Lubrication (MQL) technique
obtained a significant attention in machining processes to reduce
environmental loads caused by usage of conventional cutting fluids.
Recently nanofluids are finding an extensive application in the field
of mechanical engineering because of their superior lubrication and
heat dissipation characteristics. This paper investigates the use of a
nanofluid under MQL mode to improve grinding characteristics of
Ti-6Al-4V alloy. Taguchi-s experimental design technique has been
used in the present investigation and a second order model has been
established to predict grinding forces and surface roughness.
Different concentrations of water based Al2O3 nanofluids were
applied in the grinding operation through MQL setup developed in
house and the results have been compared with those of conventional
coolant and pure water. Experimental results showed that grinding
forces reduced significantly when nano cutting fluid was used even at
low concentration of the nano particles and surface finish has been
found to improve with higher concentration of the nano particles.
Abstract: Active vibration control is an important problem in
structures. The objective of active vibration control is to reduce the vibrations of a system by automatic modification of the system-s
structural response. In this paper, the modeling and design of a fast
output sampling feedback controller for a smart flexible beam system embedded with shear sensors and actuators for SISO system using
Timoshenko beam theory is proposed. FEM theory, Timoshenko beam theory and the state space techniques are used to model the
aluminum cantilever beam. For the SISO case, the beam is divided into 5 finite elements and the control actuator is placed at finite
element position 1, whereas the sensor is varied from position 2 to 5, i.e., from the nearby fixed end to the free end. Controllers are
designed using FOS method and the performance of the designed FOS controller is evaluated for vibration control for 4 SISO models
of the same plant. The effect of placing the sensor at different locations on the beam is observed and the performance of the
controller is evaluated for vibration control. Some of the limitations of the Euler-Bernoulli theory such as the neglection of shear and
axial displacement are being considered here, thus giving rise to an accurate beam model. Embedded shear sensors and actuators have
been considered in this paper instead of the surface mounted sensors
and actuators for vibration suppression because of lot of advantages. In controlling the vibration modes, the first three dominant modes of
vibration of the system are considered.
Abstract: Human amniotic membrane (HAM) is a useful
biological material for the reconstruction of damaged ocular surface.
The processing and preservation of HAM is critical to prevent the
patients undergoing amniotic membrane transplant (AMT) from cross
infections. For HAM preparation human placenta is obtained after an
elective cesarean delivery. Before collection, the donor is screened
for seronegativity of HCV, Hbs Ag, HIV and Syphilis. After
collection, placenta is washed in balanced salt solution (BSS) in
sterile environment. Amniotic membrane is then separated from the
placenta as well as chorion while keeping the preparation in BSS.
Scrapping of HAM is then carried out manually until all the debris is
removed and clear transparent membrane is acquired. Nitrocellulose
membrane filters are then placed on the stromal side of HAM, cut
around the edges with little membrane folded towards other side
making it easy to separate during surgery. HAM is finally stored in
solution of glycerine and Dulbecco-s Modified Eagle Medium
(DMEM) in 1:1 ratio containing antibiotics. The capped borosil vials
containing HAM are kept at -80°C until use. This vial is thawed to
room temperature and opened under sterile operation theatre
conditions at the time of surgery.
Abstract: In the present paper, the three-dimensional
temperature field of tool is determined during the machining and
compared with experimental work on C45 workpiece using carbide
cutting tool inserts. During the metal cutting operations, high
temperature is generated in the tool cutting edge which influence on
the rate of tool wear. Temperature is most important characteristic of
machining processes; since many parameters such as cutting speed,
surface quality and cutting forces depend on the temperature and high
temperatures can cause high mechanical stresses which lead to early
tool wear and reduce tool life. Therefore, considerable attention is
paid to determine tool temperatures. The experiments are carried out
for dry and orthogonal machining condition. The results show that
the increase of tool temperature depends on depth of cut and
especially cutting speed in high range of cutting conditions.
Abstract: In this study, we discussed the effects on the thermal
comfort of super high-rise residences that how effected by the high
thermal capacity structural components. We considered different
building orientations, structures, and insulation methods. We used the
dynamic simulation software THERB (simulation of the thermal
environment of residential buildings). It can estimate the temperature,
humidity, sensible temperature, and heating/cooling load for multiple
buildings. In the past studies, we examined the impact of
air-conditioning loads (hereinafter referred to as AC loads) on the
interior structural parts and the AC-usage patterns of super-high-rise
residences.
Super-high-rise residences have more structural components such
as pillars and beams than do ordinary apartment buildings. The
skeleton is generally made of concrete and steel, which have high
thermal-storage capacities. The thermal-storage capacity of
super-high-rise residences is considered to have a larger impact on the
AC load and thermal comfort than that of ordinary residences.
We show that the AC load of super-high-rise units would be
reduced by installing insulation on the surfaces of interior walls that
are not usually insulated in Japan.
Abstract: It is well known that the abrasive particles in the
abrasive water suspension has significant effect on the erosion
characteristics of the inside surface of the nozzle. Abrasive particles
moving with the flow cause severe skin friction effect, there by
altering the nozzle diameter due to wear which in turn reflects on the
life of the nozzle for effective machining. Various commercial
abrasives are available for abrasive water jet machining. The erosion
characteristic of each abrasive is different. In consideration of this
aspect, in the present work, the effect of abrasive materials namely
garnet, aluminum oxide and silicon carbide on skin friction
coefficient due to wall shear stress and jet kinetic energy has been
analyzed. It is found that the abrasive material of lower density
produces a relatively higher skin friction effect and higher jet exit
kinetic energy.
Abstract: The aim of this study is to analyze influence of
differences of heat insulation methods on indoor thermal environment and comfort of apartment buildings.
This study analyzes indoor thermal environment and comfort on units of apartment buildings using calculation software "THERB" and
compares three different kinds of heat insulation methods. Those are
outside insulation on outside walls, inside insulation on outside walls and interior insulation. In terms of indoor thermal environment, outside insulation is the best to stabilize room temperature. In winter, room temperature on
outside insulation after heating is higher than other and it is kept 3-5 degrees higher through all night. But the surface temperature with
outside insulation did not dramatically increase when heating was used, which was 3 to 5oC lower than the temperature with other
insulation. The PMV of interior insulation fall nearly range of comfort when the heating and cooling was use.
Abstract: In this paper a novel method was presented for
evaluating the fabric pills using digital image processing techniques. This work provides a novel technique for
detecting pills and also measuring their heights, surfaces and
volumes. Surely, measuring the intensity of defects by human vision is an inaccurate method for quality control; as a result, this problem became a motivation for employing digital image processing techniques for detection of defects of fabric
surface. In the former works, the systems were just limited to measuring of the surface of defects, but in the presented
method the height and the volume of defects were also
measured, which leads to a more accurate quality control. An algorithm was developed to first, find pills and then measure their average intensity by using three criteria of height, surface
and volume. The results showed a meaningful relation
between the number of rotations and the quality of pilled fabrics.
Abstract: The main focus of this paper is on the human induced
forces. Almost all existing force models for this type of load (defined
either in the time or frequency domain) are developed from the
assumption of perfect periodicity of the force and are based on force
measurements conducted on rigid (i.e. high frequency) surfaces. To
verify the different authors conclusions the vertical pressure
measurements invoked during the walking was performed, using
pressure gauges in various configurations. The obtained forces are
analyzed using Fourier transformation. This load is often decisive in
the design of footbridges. Design criteria and load models proposed
by widely used standards and other researchers were introduced and a
comparison was made.
Abstract: Nylon 6-clay hybrid/neat nylon 6, sheath/core
bicomponent nanocomposite fibers containing 4 wt% of clay in
sheath section were melt spun at different take-up speeds. Their
orientation and crystalline structure were compared to those of neat
nylon 6 fibers. Birefringence measurements showed that the
orientation development in sheath and core parts of bicomponent
fibers was different. Crystallinity results showed that clay did not act
as a nucleating agent for bicomponent fibers. The neat nylon 6 fiber
had a smooth surface while striped pattern was appeared on the
surface of bicomponent fiber containing clay due to thermal
shrinkage of the core part.