Abstract: In this paper, stabilization of an Active Magnetic Bearing (AMB) system with varying rotor speed using Sliding Mode Control (SMC) technique is considered. The gyroscopic effect inherited in the system is proportional to rotor speed in which this nonlinearity effect causes high system instability as the rotor speed increases. Also, transformation of the AMB dynamic model into a new class of uncertain system shows that this gyroscopic effect lies in the mismatched part of the system matrix. Moreover, the current gain parameter is allowed to be varied in a known bound as an uncertainty in the input matrix. SMC design method is proposed in which the sufficient condition that guarantees the global exponential stability of the reduced-order system is represented in Linear Matrix Inequality (LMI). Then, a new chattering-free control law is established such that the system states are driven to reach the switching surface and stay on it thereafter. The performance of the controller applied to the AMB model is demonstrated through simulation works under various system conditions.
Abstract: In this article, various models of surface tension force (CSF, CSS and PCIL) for interfacial flows have been applied to dynamic case and the results were compared. We studied the Kelvin- Helmholtz instabilities, which are produced by shear at the interface between two fluids with different physical properties. The velocity inlet is defined as a sinusoidal perturbation. When gravity and surface tension are taking into account, we observe the development of the Instability for a critic value of the difference of velocity of the both fluids. The VOF Model enables to simulate Kelvin-Helmholtz Instability as dynamic case.
Abstract: As application of re-activation of backside on power
device Insulated Gate Bipolar Transistor (IGBT), laser annealing was
employed to irradiate amorphous silicon substrate, and resistivities
were measured using four point probe measurement. For annealing
the amorphous silicon two lasers were used at wavelength of visible
green (532 nm) together with Infrared (793 nm). While the green
laser efficiently increased temperature at top surface the Infrared
laser reached more deep inside and was effective for melting the
top surface. A finite element method was employed to evaluate time
dependent thermal distribution in silicon substrate.
Abstract: A numerical investigation of surface heat transfer
characteristics of turbulent air flows in different parallel plate
grooved channels is performed using CFD code. The results are
obtained for Reynolds number ranging from 10,000 to 30,000 and for
arc-shaped and rectangular grooved channels. The influence of
different geometric parameters of dimples as well as the number of
them and the geometric and thermophysical properties of channel
walls are studied. It is found that there exists an optimum value for
depth of dimples in which the largest wall heat flux can be achieved.
Also, the results show a critical value for the ratio of wall thermal
conductivity to the one of fluid in which the dependence of wall heat
flux to this ratio almost vanishes. In most cases examined, heat
transfer enhancement is larger for arc-shaped grooved channels than
rectangular ones.
Abstract: Safety, river environment, and sediment utilization are the elements of the target of sediment management. As a change in an element by sediment management, may affect the other two elements, and the priority among three elements depends on stakeholders. It is necessary to develop a method to evaluate the effect of sediment management on each element and an integrated evaluation method for socio-economic effect. In this study, taking Mount Merapi basin as an investigation field, the method for an active volcanic basin was developed. An integrated evaluation method for sediment management was discussed from a socio-economic point on safety, environment, and sediment utilization and a case study of sediment management was evaluated by means of this method. To evaluate the effect of sediment management, some parameters on safety, utilization, and environment have been introduced. From a utilization point of view, job opportunity, additional income of local people, and tax income to local government were used to evaluate the effectiveness of sediment management. The risk degree of river infrastructure was used to describe the effect of sediment management on a safety aspect. To evaluate the effects of sediment management on environment, the mean diameter of grain size distribution of riverbed surface was used. On the coordinate system designating these elements, the direction of change in basin condition by sediment management can be predicted, so that the most preferable sediment management can be decided. The results indicate that the cases of sediment management tend to give the negative impacts on sediment utilization. However, these sediment managements will give positive impacts on safety and environment condition. Evaluation result from a social-economic point of view shows that the case study of sediment management reduces job opportunity and additional income for inhabitants as well as tax income for government. Therefore, it is necessary to make another policy for creating job opportunity for inhabitants to support these sediment managements.
Abstract: This paper presents a sensing system for 3D sensing
and mapping by a tracked mobile robot with an arm-type sensor
movable unit and a laser range finder (LRF). The arm-type sensor
movable unit is mounted on the robot and the LRF is installed at the
end of the unit. This system enables the sensor to change position and
orientation so that it avoids occlusions according to terrain by this
mechanism. This sensing system is also able to change the height of
the LRF by keeping its orientation flat for efficient sensing. In this kind
of mapping, it may be difficult for moving robot to apply mapping
algorithms such as the iterative closest point (ICP) because sets of the
2D data at each sensor height may be distant in a common surface. In
order for this kind of mapping, the authors therefore applied
interpolation to generate plausible model data for ICP. The results of
several experiments provided validity of these kinds of sensing and
mapping in this sensing system.
Abstract: Technology assessment is a vital part of decision process in manufacturing, particularly for decisions on selection of new sustainable manufacturing processes. To assess these processes, a matrix approach is introduced and sustainability assessment models are developed. Case studies show that the matrix-based approach provides a flexible and practical way for sustainability evaluation of new manufacturing technologies such as those used in surface coating. The technology assessment of coating processes reveals that compared with powder coating, the sol-gel coating can deliver better technical, economical and environmental sustainability with respect to the selected sustainability evaluation criteria for a decorative coating application of car wheels.
Abstract: The storage of thermal energy as a latent heat of phase
change material (PCM) has created considerable interest among
researchers in recent times. Here, an attempt is made to carry out
numerical investigations to analyze the performance of latent heat
storage units (LHSU) employing phase change material. The
mathematical model developed is based on an enthalpy formulation.
Freezing time of PCM packed in three different shaped containers
viz. rectangular, cylindrical and cylindrical shell is compared. The
model is validated with the results available in the literature. Results
show that for the same mass of PCM and surface area of heat
transfer, cylindrical shell container takes the least time for freezing
the PCM and this geometric effect is more pronounced with an
increase in the thickness of the shell than that of length of the shell.
Abstract: The fundamental aim of extended expansion concept is
to achieve higher work done which in turn leads to higher thermal
efficiency. This concept is compatible with the application of
turbocharger and LHR engine. The Low Heat Rejection engine was
developed by coating the piston crown, cylinder head inside with
valves and cylinder liner with partially stabilized zirconia coating of
0.5 mm thickness. Extended expansion in diesel engines is termed as
Miller cycle in which the expansion ratio is increased by reducing the
compression ratio by modifying the inlet cam for late inlet valve
closing. The specific fuel consumption reduces to an appreciable level
and the thermal efficiency of the extended expansion turbocharged
LHR engine is improved.
In this work, a thermodynamic model was formulated and
developed to simulate the LHR based extended expansion
turbocharged direct injection diesel engine. It includes a gas flow
model, a heat transfer model, and a two zone combustion model. Gas
exchange model is modified by incorporating the Miller cycle, by
delaying inlet valve closing timing which had resulted in considerable
improvement in thermal efficiency of turbocharged LHR engines. The
heat transfer model, calculates the convective and radiative heat
transfer between the gas and wall by taking into account of the
combustion chamber surface temperature swings. Using the two-zone
combustion model, the combustion parameters and the chemical
equilibrium compositions were determined. The chemical equilibrium
compositions were used to calculate the Nitric oxide formation rate by
assuming a modified Zeldovich mechanism. The accuracy of this
model is scrutinized against actual test results from the engine. The
factors which affect thermal efficiency and exhaust emissions were
deduced and their influences were discussed. In the final analysis it is
seen that there is an excellent agreement in all of these evaluations.
Abstract: Implementation of response surface methodology (RSM) was employed to study the effects of two factor (rubber clearance and round per minute) in brown rice peeling machine of The optimal BROKENS yield (19.02, average of three repeats),.The optimized composition derived from RSM regression was analyzed using Regression analysis and Analysis of Variance (ANOVA). At a significant level α = 0.05, the values of Regression coefficient, R 2 (adj)were 97.35 % and standard deviation were 1.09513. The independent variables are initial rubber clearance, and round per minute parameters namely. The investigating responses are final rubber clearance, and round per minute (RPM). The restriction of the optimization is the designated.
Abstract: The gustatory system allows animals to distinguish
varieties of food and affects greatly the consumption of food, hence
the health and growth of animals. In the current study, we
investigated the histogenesis of vallate papillae (VLP) in the rabbit
tongue using light and scanning electron microscopy. Samples were
obtained from rabbit embryos at the embryonic days 16-30 (E16-30),
and from newborns until maturity; 6 months. At E16, the first
primordia of vallate papillae were observed as small pits on the
surface epithelium of the tongue-s root. At E18, the caudal part was
prominent with loose mesenchymal tissue core; meanwhile the rostral
part of the papilla was remained as a thick mass of epithelial cells. At
E20-24, the side epithelium formed the primitive annular groove. At
E26, the primitive taste buds appeared only at the papillary surface
and reached their maturity by E28. The annular groove started to
appear at E26 became more defined at E28. The definitive vallate
papillae with substantial number of apparently mature taste buds
were observed by the end of the second week. We conclude that the
vallate papillae develop early and mature during the early postnatal
life.
Abstract: Saturated hydraulic conductivity is one of the soil
hydraulic properties which is widely used in environmental studies
especially subsurface ground water. Since, its direct measurement is
time consuming and therefore costly, indirect methods such as
pedotransfer functions have been developed based on multiple linear
regression equations and neural networks model in order to estimate
saturated hydraulic conductivity from readily available soil
properties e.g. sand, silt, and clay contents, bulk density, and organic
matter. The objective of this study was to develop neural networks
(NNs) model to estimate saturated hydraulic conductivity from
available parameters such as sand and clay contents, bulk density,
van Genuchten retention model parameters (i.e. r
θ , α , and n) as well
as effective porosity. We used two methods to calculate effective
porosity: : (1) eff s FC φ =θ -θ , and (2) inf φ =θ -θ eff s , in which s
θ is
saturated water content, FC θ is water content retained at -33 kPa
matric potential, and inf θ is water content at the inflection point.
Total of 311 soil samples from the UNSODA database was divided
into three groups as 187 for the training, 62 for the validation (to
avoid over training), and 62 for the test of NNs model. A commercial
neural network toolbox of MATLAB software with a multi-layer
perceptron model and back propagation algorithm were used for the
training procedure. The statistical parameters such as correlation
coefficient (R2), and mean square error (MSE) were also used to
evaluate the developed NNs model. The best number of neurons in
the middle layer of NNs model for methods (1) and (2) were
calculated 44 and 6, respectively. The R2 and MSE values of the test
phase were determined for method (1), 0.94 and 0.0016, and for
method (2), 0.98 and 0.00065, respectively, which shows that method
(2) estimates saturated hydraulic conductivity better than method (1).
Abstract: In this study, we sought to investigate the mercury
removal efficiency of manganese oxides from natural gas. The
fundamental studies on mercury removal with manganese oxides
sorbents were carried out in a laboratory scale fixed bed reactor at 30
°C with a mixture of methane (20%) and nitrogen gas laden with 4.8
ppb of elemental mercury. Manganese oxides with varying surface
area and crystalline phase were prepared by conventional precipitation
method in this study. The effects of surface area, crystallinity and
other metal oxides on mercury removal efficiency were investigated.
Effect of Ag impregnation on mercury removal efficiency was also
investigated. Ag supported on metal oxide such titania and zirconia as
reference materials were also used in this study for comparison. The
characteristics of mercury removal reaction with manganese oxide
was investigated using a temperature programmed desorption (TPD)
technique.
Manganese oxides showed very high Hg removal activity (about
73-93% Hg removal) for first time use. Surface area of the manganese
oxide samples decreased after heat-treatment and resulted in complete
loss of Hg removal ability for repeated use after Hg desorption in the
case of amorphous MnO2, and 75% loss of the initial Hg removal
activity for the crystalline MnO2. Mercury desorption efficiency of
crystalline MnO2 was very low (37%) for first time use and high (98%)
after second time use. Residual potassium content in MnO2 may have
some effect on the thermal stability of the adsorbed Hg species.
Desorption of Hg from manganese oxides occurs at much higher
temperatures (with a peak at 400 °C) than Ag/TiO2 or Ag/ZrO2.
Mercury may be captured on manganese oxides in the form of mercury
manganese oxide.
Abstract: Electro Discharge Sawing is a hybrid process
combining the features of SEDM and ECM. Its major characteristic is
extremely fast erosion rate compare to either of the above processes.
This paper brings out its relative feature of SEDM and EDS about
their erosion rates, surface roughness, and morphology of machined
surfaces.
Abstract: This work presents a methodology for the design and
manufacture of propellers oriented to the experimental verification of
theoretical results based on the combined model. The design process
begins by using algorithms in Matlab which output data contain the
coordinates of the points that define the blade airfoils, in this case the
NACA 6512 airfoil was used. The modeling for the propeller blade
was made in NX7, through the imported files in Matlab and with the
help of surfaces. Later, the hub and the clamps were also modeled.
Finally, NX 7 also made possible to create post-processed files to the
required machine. It is possible to find the block of numbers with G
& M codes about the type of driver on the machine. The file
extension is .ptp. These files made possible to manufacture the blade,
and the hub of the propeller.
Abstract: A strategy is implemented to find the improved configuration design of an existing aircraft structure by executing topology and shape optimizations. Structural analysis of the Initial Design Space is performed in ANSYS under the loads pertinent to operating and ground conditions. By using the FEA results and data, an initial optimized layout configuration is attained by exploiting nonparametric topology optimization in TOSCA software. Topological optimized surfaces are then smoothened and imported in ANSYS to develop the geometrical features. Nodes at the critical locations of resulting voids are selected for sketching rough profiles. Rough profiles are further refined and CAD feasible geometric features are generated. The modified model is then analyzed under the same loadings and constraints as defined for topology optimization. Shape at the peak stress concentration areas are further optimized by exploiting the shape optimization in TOSCA.shape module. The harmonized stressed model with the modified surfaces is then imported in CATIA to develop the final design.
Abstract: Earthquakes are natural phenomena that occur with influence of a lot of parameters such as seismic activity, changing in the ground waters' motion, changing in the water-s temperature, etc. On the other hand, the radon gas concentrations in soil vary as nonlinear generally with earthquakes. Continuous measurement of the soil radon gas is very important for determination of characteristic of the seismic activity. The radon gas changes as continuous with strain occurring within the Earth-s surface during an earthquake and effects from the physical and the chemical processes such as soil structure, soil permeability, soil temperature, the barometric pressure, etc. Therefore, at the modeling researches are notsufficient to knowthe concentration ofradon gas. In this research, we determined relationships between radon emissions based on the environmental parameters and earthquakes occurring along the East Anatolian Fault Zone (EAFZ), Turkiye and predicted magnitudes of some earthquakes with the artificial neural network (ANN) model.
Abstract: This study deals with a multi-criteria optimization
problem which has been transformed into a single objective
optimization problem using Response Surface Methodology (RSM),
Artificial Neural Network (ANN) and Grey Relational Analyses
(GRA) approach. Grey-RSM and Grey-ANN are hybrid techniques
which can be used for solving multi-criteria optimization problem.
There have been two main purposes of this research as follows.
1. To determine optimum and robust fiber dyeing process
conditions by using RSM and ANN based on GRA,
2. To obtain the best suitable model by comparing models
developed by different methodologies.
The design variables for fiber dyeing process in textile are
temperature, time, softener, anti-static, material quantity, pH,
retarder, and dispergator. The quality characteristics to be evaluated
are nominal color consistency of fiber, maximum strength of fiber,
minimum color of dyeing solution. GRA-RSM with exact level
value, GRA-RSM with interval level value and GRA-ANN models
were compared based on GRA output value and MSE (Mean Square
Error) performance measurement of outputs with each other. As a
result, GRA-ANN with interval value model seems to be suitable
reducing the variation of dyeing process for GRA output value of the
model.
Abstract: Charging and discharging phenomenon on the surface
of materials can be found in plasma display panel, spacecraft
charging, high voltage insulator, etc. This report gives a simple
explanation on this phenomenon. A scanning electron microscope
was used not only as a tool to produce energetic electron beam to
charge an insulator without metallic coating and to produce a surface
discharging (surface breakdown/flashover) but also to observe the
visible charging and discharging on the sample surface. A model of
electric field distribution on the surface was developed in order to
explain charging and discharging phenomena. Since charging and
discharging process involves incubation time, therefore this process
can be used to evaluate the insulation property of materials under
electron bombardment.
Abstract: The springs located in urban areas are the outpouring
of surface water, which can serve as water supply, effluent receptors
and important local macro-drainage elements. With unplanned
occupation, non-compliance with environmental legislation and the
importance of these water bodies, it is vital to analyze the springs
within urban areas, considering the Brazilian forest code. This paper
submits an analysis and discussion methodology proposal of
environmental compliance functions of urban springs, by means of
G.I.S. - Geographic Information System analysis - and in situ
analysis. The case study included two springs which exhibit a history
of occupation along its length, with different degrees of impact. The
proposed method is effective and easy to apply, representing a
powerful tool for analyzing the environmental conditions of springs
in urban areas.