Abstract: The important issue considered in the widespread deployment of Wireless Sensor Networks (WSNs) is an efficiency of the energy consumption. In this paper, we present a study of the optimal relay station planning problems using Binary Integer Linear Programming (BILP) model to minimize the energy consumption in WSNs. Our key contribution is that the proposed model not only ensures the required network lifetime but also guarantees the radio connectivity at high level of communication quality. Specially, we take into account effects of noise, signal quality limitation and bit error rate characteristics. Numerical experiments were conducted in various network scenarios. We analyzed the effects of different sensor node densities and distribution on the energy consumption.
Abstract: In this paper, a thermal model of cast- resin dry type
transformer is proposed. The proposed thermal model is solved by
finite element technique to get the temperature at any location of the
transformer. The basic modes of heat transfer such as conduction;
convection and radiation are used to get the steady state temperature
distribution of the transformer. The predicted temperatures are
compared with experimental results reported in this paper and it is
found a good agreement between them. The effects of various
parameters such as width of air duct, ambient temperature and
emissivity of the outer surface were also studied.
Abstract: Separation of propylene-propane mixture using
immobilized liquid membrane was investigated. The effect of transmembrane
pressure and carrier concentration on membrane
separation performance was studied. It was observed that for 30:70
(vol. %) propylene-propane mixture, at pressure of 120kPa and
carrier concentration of 20wt. %, a separation factor of 474 was
obtained.
Abstract: Liquid-liquid extraction is a process using two immiscible
liquids to extract compounds from one phase without high
temperature requirement. Mostly, the technical implementation of
this process is carried out in mixer-settlers or extraction columns. In
real chemical processes, chemicals may have high viscosity and
contain impurities. These impurities may change the settling behavior
of the process without measurably changing the physical properties
of the phases. In the current study, the settling behavior and the affected
parameters in a high-viscosity system were observed. Batchsettling
experiments were performed to experimentally quantify the
settling behavior and the mixer-settler model of Henschke [1] was
used to evaluate the behavior of the toluene + water system. The
viscosity of the system was increased by adding polyethylene glycol
4000 to the aqueous phase. NaCl and Na2SO4 were used to study the
influence of electrolytes. The results from this study show that increasing
the viscosity of water has a higher influence on the settling
behavior in comparison to the effects of the electrolytes. It can be
seen from the experiments that at high salt concentrations, there was
no effect on the settling behavior.
Abstract: This research paper designs a unique motion planner
of multiple platoons of nonholonomic car-like robots as a feasible
solution to the lane changing/merging maneuvers. The decentralized
planner with a leaderless approach and a path-guidance principle
derived from the Lyapunov-based control scheme generates collision
free avoidance and safe merging maneuvers from multiple lanes to a
single lane by deploying a split/merge strategy. The fixed obstacles
are the markings and boundaries of the road lanes, while the moving
obstacles are the robots themselves. Real and virtual road lane
markings and the boundaries of road lanes are incorporated into a
workspace to achieve the desired formation and configuration of the
robots. Convergence of the robots to goal configurations and the
repulsion of the robots from specified obstacles are achieved by
suitable attractive and repulsive potential field functions,
respectively. The results can be viewed as a significant contribution
to the avoidance algorithm of the intelligent vehicle systems (IVS).
Computer simulations highlight the effectiveness of the split/merge
strategy and the acceleration-based controllers.
Abstract: Fuel cell is an emerging technology in the field
of renewable energy sources which has the capacity to replace
conventional energy generation sources. Fuel cell utilizes hydrogen
energy to produce electricity. The electricity generated by the fuel
cell can’t be directly used for a specific application as it needs
proper power conditioning. Moreover, the output power fluctuates
with different operating conditions. To get a stable output power
at an economic rate, power conditioning circuit is essential for fuel
cell. This paper implements a two-staged power conditioning unit for
fuel cell based distributed generation using hysteresis current control
technique.
Abstract: In the article the experience of principle new
technology development of ethnopsychological experiment on the
basis of using other virtual independent experimental variables is
presented. It is shown that ethnic prejudices are the result of forming
and development of specific semantic barriers, arising up in the
conditions of interethnic co-operation and people-s communication.
Their overcoming is more successful in the conditions of the special
organized process of teaching in a polyethnic environment,
characteristic for the modern institute
Abstract: According to the European laws, there is the
possibility of reusing the washing wastes for the environmental
requalification of quarry lakes. The paper deals with the
hydrogeological aspects involved in this possibility, as the
introduction of finest wastes in the quarry lakes can generate
alterations of the hydrogeological setting of the area, and problems
for the future accessibility of the zone. To evaluate the
hydrogeological compatibility of the washing wastes reuse in quarry
lakes a groundwater numerical model was carried out, pointing out
both the hydrogeological feasibility of this intervention and some
guide lines for its optimization, in terms of inflow point with regard
the groundwater flow direction and loss of volume in the quarry lake.
Abstract: This experiment was conducted to investigate the
effect of different levels of dietary chromium yeast (Cr-yeast) on
thigh meat quality of broiler chicks reared under heat stress
condition. Two hundred and forty Ross male chickens in heat stress
condition (33±3°C) were allocated to five treatments in a completely
randomized design. Treatments were supplemented with 0 (control),
200, 400, 800 and 1200 μg kg-1 Cr in the form of Cr yeast. Twelve
chicks from each treatment were slaughtered at 42 d, to evaluate
moisture, protein, lipid, pH and lipid oxidation of thigh meat.
Protein, moisture, lipid and pH of thigh meat were not affected by
supplemental Cr. Thigh meat lipid tended to decrease in broilers
received 1200 μg kg-1. Storage time increased lipid oxidation of
meat (P
Abstract: Transdermal delivery of ondansetron hydrochloride (OdHCl) can prevent the problems encountered with oral ondansetron. In previously conducted studies, effect of amount of polyvinyl pyrrolidone, permeation enhancer and casting solvent on the physicochemical properties on OdHCl were investigated. It is feasible to develop ondansetron transdermal patch by using ethyl cellulose and polyvinyl pyrrolidone with dibutyl pthalate as plasticizer, however, the desired flux is not achieved. The primary aim of this study is to use dimethyl succinate (DMS) and propylene glycol that are not incorporated in previous studies to determine their effect on the physicochemical properties of an OdHCl transdermal patch using ethyl cellulose and polyvinyl pyrrolidone. This study also investigates the effect of permeation enhancer (eugenol and phosphatidylcholine) on the release of OdHCl. The results showed that propylene glycol is a more suitable plasticizer compared to DMS in the fabrication of OdHCl transdermal patch using ethyl cellulose and polyvinyl pyrrolidone as polymers. Propylene glycol containing patch has optimum drug content, thickness, moisture content and water absorption, tensile strength, and a better release profile than DMS. Eugenol and phosphatidylcholine can increase release of OdHCl from the patches. From the physicochemical result and permeation profile, a combination of 350mg of ethyl cellulose, 150mg polyvinyl pyrrolidone, 3% of total polymer weight of eugenol, and 40% of total polymer weight of propylene glycol is the most suitable formulation to develop an OdHCl patch. OdHCl release did not increase with increasing the percentage of plasticiser. DMS 4, PG 4, DMS 9, PG 9, DMS 14, and PG 14 gave better release profiles where using 300mg: 0mg, 300mg: 100mg, and 350mg: 150mg of EC: PVP. Thus, 40% of PG or DMS appeared to be the optimum amount of plasticiser when the above combination where EC: PVP was used. It was concluded from the study that a patch formulation containing 350mg EC, 150mg PVP, 40% PG and 3% eugenol is the best transdermal matrix patch compositions for the uniform and continuous release/permeation of OdHCl over an extended period. This patch design can be used for further pharmacokinetic and pharmacodynamic studies in suitable animal models.
Abstract: The critical period for weed control (CPWC) is the period in the crop growth cycle during which weeds must be controlled to prevent unacceptable yield losses. Field studies were conducted in 2005 and 2006 in the University of Birjand at the south east of Iran to determine CPWC of corn using a randomized complete block design with 14 treatments and four replications. The treatments consisted of two different periods of weed interference, a critical weed-free period and a critical time of weed removal, were imposed at V3, V6, V9, V12, V15, and R1 (based on phonological stages of corn development) with a weedy check and a weed-free check. The CPWC was determined with the use of 2.5, 5, 10, 15 and 20% acceptable yield loss levels by non-linear Regression method and fitting Logistic and Gompertz nonlinear equations to relative yield data. The CPWC of corn was from 5- to 15-leaf stage (19-55 DAE) to prevent yield losses of 5%. This period to prevent yield losses of 2.5, 10 and 20% was 4- to 17-leaf stage (14-59 DAE), 6- to 12-leaf stage (25-47 DAE) and 8- to 9-leaf stage (31-36 DAE) respectively. The height and leaf area index of corn were significantly decreased by weed competition in both weed free and weed infested treatments (P
Abstract: In order to supplement the brittle property of concrete,
fibers are added into concrete mixtures. Compared to general concrete,
various characteristics such as tensile strength, bending strength,
bending toughness, and resistance to crack are superior, and even
when cracks occur, improvements on toughness as well as resistance
to shock are excellent due to the growth of fracture energy. Increased
function of steel fiber reinforced concrete can be differentiated
depending on the fiber dispersion, and sand percentage can be an
important influence on the fiber dispersion. Therefore, in this research,
experiments were planned on sand percentage in order to apprehend
the influence of sand percentage on the bending properties and direct
tension of SFRC and basic experiments were conducted on bending
and direct tension in order to recognize the properties of bending
properties and direct tension following the size of the aggregates and
sand percentage.
Abstract: This paper aims to argue that religion and Faith-based Organizations (FBOs) contribute to building democratic process through the provision of education in Sierra Leone. Sierra Leone experienced a civil war from 1991 to 2002 and about 70 percent of the population lives in poverty. While the government has been in the process of rebuilding the nation, many forms of Civil Society Organizations (CSOs), including FBOs, have played a significant role in promoting social development. Education plays an important role in supporting people-s democratic movements through knowledge acquisition, spiritual enlightenment and empowerment. This paper discusses religious tolerance in Sierra Leone and how FBOs have contributed to the provision of primary education in Sierra Leone. This study is based on the author-s field research, which involved interviews with teachers and development stakeholders, notably government officials, Non-governmental Organizations (NGOs) and FBOs, as well as questionnaires completed by pupils, parents and teachers.
Abstract: Since atmosphere pressure field is an actual envoy of
climatic signal the atmospheric Highs and Lows should be attributed
to the key active focal points within the ocean-atmosphere interplay
system. Here we were set a task to determine how the dynamics of
those centres of action relates to the climate change both on regional
and global scales. For this target the near-surface temperature and
atmospheric pressure differences between the Icelandic Low and the
Azores High were considered. The secular term of phase states of the
system under consideration was found divided into three
nonintersecting subsets. Each of that was put in consequence with
one of three climatic scenarios related to the periods of 1905-1935
(relatively warm phase), 1940-1970 (cold phase) and 1980-2000
(warm phase).
Abstract: We propose photo-BJMOSFET (Bipolar Junction Metal-Oxide-Semiconductor Field Effect Transistor) fabricated on SOI film. ITO film is adopted in the device as gate electrode to reduce light absorption. I-V characteristics of photo-BJMOSFET obtained in dark (dark current) and under 570nm illumination (photo current) are studied furthermore to achieve high photo-to-dark-current contrast ratio. Two variables in the calculation were the channel length and the thickness of the film which were set equal to six different values, i.e., L=2, 4, 6, 8, 10, and 12μm and three different values, i.e., dsi =100, 200 and 300nm, respectively. The results indicate that the greatest photo-to-dark-current contrast ratio is achieved with L=10μm and dsi=200 nm at VGK=0.6V.
Abstract: The improvement of irrigation systems in the Nile
Delta is one of the most important attempts in Egypt to implement
more effective irrigation technology by improving the existing
irrigation networks. Demand delivery system in the existing irrigation
network is using of mechanical gates structures to automatically
divert water from one portion of an agricultural field to another in the
desired amount and sequence. This paper discusses evaluating main
irrigation networks system under the government managed before
and after improvement systems in the Nile Delta. The overall results
indicate that policy of using the demand delivery concept through
irrigation networks is successful by improving water delivery
performance among them than the rotation delivery concept that used
before. It is provided fair share of water delivery among irrigation
districts and available water in the end of irrigation network,
although this system located in an end of irrigation networks in the
Nile Delta.
Abstract: Spray chilling using air-mist nozzles has received
much attention in the food processing industry because of the
benefits it has shown over forced air convection. These benefits
include an increase in the heat transfer coefficient and a reduction in
the water loss by the product during cooling. However, few studies
have simulated the heat transfer and aerodynamics phenomena of the
air-mist chilling process for optimal operating conditions. The study
provides insight into the optimal conditions for spray impaction, heat
transfer efficiency and control of surface flooding. A computational
fluid dynamics model using a two-phase flow composed of water
droplets injected with air is developed to simulate the air-mist
chilling of food products. The model takes into consideration
droplet-to-surface interaction, water-film accumulation and surface
runoff. The results of this study lead to a better understanding of the
heat transfer enhancement, water conservation, and to a clear
direction for the optimal design of air-mist chilling systems that can
be used in commercial applications in the food and meat processing
industries.
Abstract: Four phenylurea herbicides (isoproturon, chlortoluron, diuron and linuron) were dissolved in different water matrices in order to study their chemical degradation by using UV radiation, ozone and some advanced oxidation processes (UV/H2O2, O3/H2O2, Fenton reagent and the photo- Fenton system). The waters used were: ultra-pure water, a commercial mineral water, a groundwater and a surface water taken from a reservoir. Elimination levels were established for each herbicide and for several global quality parameters, and a kinetic study was performed in order to determine basic kinetic parameters of each reaction between the target phenylureas and these oxidizing systems.
Abstract: A major goal of any enterprise is to create a ratings
system of customer satisfaction, goods and services. It is obvious that
the company cannot change what is not measured. In order to get a
clearer picture of the preferences of the major consumer groups, this
stage should be based on extensive research, including a variety of
interviews and surveys. It is necessary to know the key benefits,
which determine customer satisfaction in the market segment, of the
properties of certain goods and services. It is important to estimate
the terms of these preferences from the viewpoint of the client. This
article discusses the importance of customer satisfaction, and ways of
assessing it.
Abstract: An ordered porous antimony-doped tin oxide (ATO) film was successfully prepared using a simple coating process with colloidal templates. The facile production was effective when a combination of 16-nm ATO (as a model of an inorganic nanoparticle) and polystyrene (PS) spheres (as a model of the template) weresimply coated to produce a composite ATO/PS film. Heat treatment was then used to remove the PS and produce the porous film. The porous film with a spherical pore shape and a highly ordered porous structure could be obtained. A potential way for the control of pore size could be also achieved by changing initial template size. The theoretical explanation and mechanism of porous formation were also added, which would be important for the scaling-up prediction and estimation.