Abstract: Household waste form a larger proportion of waste
generated across the state, accumulation of organic waste is an
apparent problem and the existing dump sites could be overstress.
Niger state has abundant arable land and water resources thus should
be one of the highest producers of agricultural crops in the country.
However, the major challenge to agricultural sector today is loss of
soil nutrient coupled with high cost of fertilizer. These have
continued to increase the use of fertilizer and decomposed solid waste
for enhance agricultural yield, which have varying effects on the soil
as well a threat to human livelihood. Consequently, vegetable yield
samples from poultry droppings, decomposed household waste
manure, NPK treatments and control from each replication were
subjected to proximate analysis to determine the nutritional and antinutritional
component as well as heavy metal concentration. Data
collected was analyzed using SPSS software and Randomized
complete Block Design means were compared. The result shows that
the treatments do not devoid the concentrations of any nutritional
components while the anti-nutritional analysis proved that NPK had
higher oxalate content than control and organic treats. The
concentration of lead and cadmium are within safe permissible level
while the mercury level exceeded the FAO/WHO maximum
permissible limit for the entire treatments depicts the need for urgent
intervention to minimize mercury levels in soil and manure in order
to mitigate its toxic effect. Thus, eco-agriculture should be widely
accepted and promoted by the stakeholders for soil amendment,
higher yield, strategies for sustainable environmental protection, food
security, poverty eradication, attainment of sustainable development
and healthy livelihood.
Abstract: The use of information technology in education have
changed not only the learners learning style but also the way they
taught, where nowadays learners are connected with diversity of
information sources with means of knowledge available everywhere.
The advantage of network wireless technologies and mobility
technologies used in the education and learning processes lead to
mobile learning as a new model of learning technology. Currently,
most of mobile learning applications are developed for the formal
education and learning environment. Despite the long history and
large amount of research on mobile learning and instruction design
model still there is a need of well-defined process in designing
mobile learning applications. Based on this situation, this paper
emphasizes on identifying instruction design phase’s considerations
and influencing factors in developing mobile learning application.
This set of instruction design steps includes analysis, design,
development, implementation, evaluation and continuous has been
built from a literature study, with focus on standards for learning,
mobile application software quality and guidelines. The effort is part
of an Omani-funded research project investigating the development,
adoption and dissemination of mobile learning in Oman.
Abstract: The Green Urban Lab took the form of public
installations that were placed at various locations in four cities in
Cyprus. These installations - through which a series of events,
activities, workshops and research took place - were the main tools in
regenerating a series of urban public spaces in Cyprus. The purpose
of this project was to identify issues and opportunities related to
public space and to offer guidelines on how design and participatory
democracy improvements could strengthen civil society, while
raising the quality of the urban public scene. Giant inflatable
structures were injected in important urban fragments in order to
accommodate series of events. The design and playful installation
generated a wide community engagement. The fluid presence of the
installations acted as a catalyst for social interaction. They were
accessed and viewed effortlessly and surprisingly, creating
opportunities to rediscover public spaces.
Abstract: Carbon Fiber Reinforced Plastics (CFRPs) are widely
used for advanced applications, in particular in aerospace, automotive
and wind energy industries. Once cured to near net shape, CFRP
parts need several finishing operations such as trimming, milling or
drilling in order to accommodate fastening hardware and meeting the
final dimensions. The present research aims to study the effect of the
cutting temperature in trimming on the mechanical strength of high
performance CFRP laminates used for aeronautics applications. The
cutting temperature is of great importance when dealing with
trimming of CFRP. Temperatures higher than the glass-transition
temperature (Tg) of the resin matrix are highly undesirable: they
cause degradation of the matrix in the trimmed edges area, which can
severely affect the mechanical performance of the entire component.
In this study, a 9.50mm diameter CVD diamond coated carbide tool
with six flutes was used to trim 24-plies CFRP laminates. A
300m/min cutting speed and 1140mm/min feed rate were used in the
experiments. The tool was heated prior to trimming using a
blowtorch, for temperatures ranging from 20°C to 300°C. The
temperature at the cutting edge was measured using embedded KType
thermocouples. Samples trimmed for different cutting
temperatures, below and above Tg, were mechanically tested using
three-points bending short-beam loading configurations. New cutting
tools as well as worn cutting tools were utilized for the experiments.
The experiments with the new tools could not prove any correlation
between the length of cut, the cutting temperature and the mechanical
performance. Thus mechanical strength was constant, regardless of
the cutting temperature. However, for worn tools, producing a cutting
temperature rising up to 450°C, thermal damage of the resin was
observed. The mechanical tests showed a reduced mean resistance in
short beam configuration, while the resistance in three point bending
decreases with increase of the cutting temperature.
Abstract: In recent years, the power system has been changed
and a flexible power pricing system such as demand response has been
sought in Japan. The demand response system works simply in the
household sector and the owner as the decision-maker, can benefit
from power saving. On the other hand, the execution of demand
response in the office building is more complex than in the household
because various people such as owners, building administrators and
occupants are involved in the decision-making process. While the
owners benefit from demand saving, the occupants are exposed to
restricted benefits of a demand-saved environment. One of the reasons
is that building systems are usually under centralized management and
each occupant cannot choose freely whether to participate in demand
response or not. In addition, it is unclear whether incentives give
occupants the motivation to participate. However, the recent
development of IT and building systems enables the personalized
control of the office environment where each occupant can control the
lighting level or temperature individually. Therefore, it can be possible
to have a system which each occupant can make a decision of whether
or not to participate in demand response in the office building. This study investigates personal responses to demand response
requests, under the condition where each occupant can adjust their
brightness individually in their workspace. Once workers participate
in the demand response, their desk-lights are automatically turned off.
The participation rates in the demand response events are compared
among four groups, which are divided by different motivation, the
presence, or absence of incentives and the method of participation. The
result shows that there are significant differences of participation rates
in demand response event between four groups. The method of
participation has a large effect on the participation rate. The “Opt-out”
groups where the occupants are automatically enrolled in a demand
response event if they do not express non-participation have the
highest participation rate in the four groups. Incentives also have an
effect on the participation rate. This study also reports on the impact of low illumination office
environment on the occupants, such as stress or fatigue. The
electrocardiogram and the questionnaire are used to investigate the
autonomic nervous activity and subjective fatigue symptoms of the
occupants. There is no big difference between dim workspace during
demand response event and bright workspace in autonomic nervous
activity and fatigue.
Abstract: Public participation in recycling domestic waste is still
very low in Malaysia. Only 10.5% of solid waste was recycled up to
now which is far below than of in developed countries. Therefore,
understanding public motivations towards recycling domestic waste
are important to improve current recycling rate. Thus, this study
attempts to identify what are the possible motivations and hindrances
for the public to recycle. Open-ended questions format were
administered to 484 people in Kota Kinabalu, Sabah, Malaysia. Two
specific questions we asked to explore their general determinants and
barriers in practicing recycling: “What motivates you to recycle?”
and “What are the barriers you encountered in doing recycling
activities?” Thematic was conducted on the open-ended questions in
which themes were created with the raw comments. It was found that
the underlying recycling motivations are (i) awareness’ towards the
environment; (ii) benefits to the society and individual; and (iii)
social influence. Non participations are influence by (i) attitudes; (ii)
commitment; (iii) facilities; (iv) knowledge; (v) inconvenience; and
(vi) enforcement.
Abstract: Dead wood and habitat tree such as fallen logs, snags,
stumps and cracks and loos bark etc. are regarded as an important
ecological component of forests on which many forest dwelling
species depend on presence of them within forest ecosystems.
Meanwhile its relation to management history in Caspian forest has
gone unreported. The aim of research was to compare the amounts of
dead wood and habitat trees in the forests with historically different
intensities of management, including: forests with the long term
implication of management (PS), the short term implication of
management (NS) which were compared with semi virgin forest
(GS). The number of 405 individual dead and habitat trees were
recorded and measured at 109 sampling locations. ANOVA revealed
volume of dead tree in the form and decay classes significantly differ
within sites and dead volume in the semi virgin forest significantly
higher than managed sites. Comparing the amount of dead and
habitat tree in three sites showed that, dead tree volume related with
management history and significantly differ in three study sites.
Meanwhile, frequency of habitat trees was significantly different
within sites. The highest amount of habitat trees including cavities,
cracks and loose bark and fork split trees was recorded in virgin site
and lowest recorded in the sites with the long term implication of
management. It can be concluded that forest management cause
reduction of the amount of dead and habitat tree specially in a large
size, thus managing this forest according to ecological sustainable
principles require a commitment to maintaining stand structure that
allow, continued generation of dead trees in a full range of size.
Abstract: Friction stir welding and tungsten inert gas welding
techniques were employed to weld armor grade aluminum alloy to
investigate the effect of welding processes on tensile behavior of
weld joints. Tensile tests, Vicker microhardness tests and optical
microscopy were performed on developed weld joints and base metal.
Welding process influenced tensile behavior and microstructure of
weld joints. Friction stir welded joints showed tensile behavior better
than tungsten inert gas weld joints.
Abstract: The aim of the performed work is to establish the 2D
and 3D model of direct unsteady task of sample heat treatment by
moving source employing computer model on the basis of finite
element method. Complex boundary condition on heat loaded sample
surface is the essential feature of the task. Computer model describes
heat treatment of the sample during heat source movement over the
sample surface. It is started from 2D task of sample cross section as a
basic model. Possibilities of extension from 2D to 3D task are
discussed. The effect of the addition of third model dimension on
temperature distribution in the sample is showed. Comparison of
various model parameters on the sample temperatures is observed.
Influence of heat source motion on the depth of material heat
treatment is shown for several velocities of the movement. Presented
computer model is prepared for the utilization in laser treatment of
machine parts.
Abstract: This paper presents the influence of the vertical
seismic component on the non-linear dynamics analysis of three
different structures. The subject structures were analyzed and
designed according to recent codes. This paper considers three types
of buildings: 5-, 10-, and 15-story buildings. The non-linear
dynamics analysis of the structures with assuming elastic-perfectlyplastic
behavior was performed using RAM PERFORM-3D software;
the horizontal component was taken into consideration with and
without the incorporation of the corresponding vertical component.
Dynamic responses obtained for the horizontal component acting
alone were compared with those obtained from the simultaneous
application of both seismic components. The results show that the
effect of the vertical component of ground motion may increase the
axial load significantly in the interior columns and, consequently, the
stories. The plastic mechanisms would be changed. The P-Delta
effect is expected to increase. The punching base plate shear of the
columns should be considered. Moreover, the vertical component
increases the input energy when the structures exhibit inelastic
behavior and are taller.
Abstract: Wicking and evaporation of water in porous knitted fabrics is investigated by combining experimental and analytical approaches: The standard wicking model from Lucas and Washburn is enhanced to account for evaporation and gravity effects. The goal is to model the effect of gravity and evaporation on wicking using simple analytical expressions and investigate the influence of fabrics geometrical parameters, such as porosity and thickness on evaporation impact on maximum reachable height values. The results show that fabric properties have a significant influence on evaporation effect. In this paper, an experimental study of determining water kinetics from different knitted fabrics were gravimetrically investigated permitting the measure of the mass and the height of liquid rising in fabrics in various atmospheric conditions. From these measurements, characteristic pore parameters (capillary radius and permeability) can be determined.
Abstract: A large variety of pipe flange is required in marine
and construction industry. Pipe flanges are usually welded or screwed
to the pipe end and are connected with bolts. This approach is very
simple and widely used for a long time; however, it results in high
development cost and low productivity, and the productions made by
this approach usually have safety problem at the welding area. In this
research, a new approach of forming pipe flange based on cold
forging and floating die concept is presented. This innovative
approach increases the effectiveness of the material usage and save
the time cost compared with conventional welding method. To ensure the dimensional accuracy of the final product, the finite
element analysis (FEA) was carried out to simulate the process of
cold forging, and the orthogonal experiment methods were used to
investigate the influence of four manufacturing factors (pin die angle,
pipe flange angle, rpm, pin die distance from clamp jig) and predicted
the best combination of them. The manufacturing factors were
obtained by numerical and experimental studies and it shows that the
approach is very useful and effective for the forming of pipe flange,
and can be widely used later.
Abstract: A problem of complex mineral resources development is urgent and priority, it is aimed at realization of the processes of their ecologically safe development, one of its components is revealing the influence of the forms of element compounds in raw materials and in the processing products. In view of depletion of the precious metal reserves at the traditional deposits in the XXI century the large-size open cast deposits, localized in black shale strata begin to play the leading role. Carbonaceous (black) shales carry a heightened metallogenic potential. Black shales with high content of carbon are widely distributed within the scope of Bureinsky massif. According to academician Hanchuk`s data black shales of Sutirskaya series contain generally PGEs native form. The presence of high absorptive towards carbonaceous matter gold and PGEs compounds in crude ore results in decrease of valuable components extraction because of their sorption into dissipated carbonaceous matter.
Abstract: Radical technological innovations enable companies
to reach strong market positions and are thus desirable. On the other
hand, the innovation process is related to significant costs and risks.
Hence, the knowledge of the factors that influence success is crucial
for technology driven companies. Taking a previously developed
framework of Critical Success Factors for radical technological
innovations as a reference model, we conducted a structured and
focused literature review of eleven standard books within the field of
technology and innovation management. With this approach we aim
to evaluate, expand, and clarify the set of Critical Success Factors
detailed in this framework. Overall, the set of factors and their
allocation to the main categories of the framework could be
confirmed. However, the factor organizational home is not
emphasized and discussed in most of the reviewed literature. On the
other hand, an additional factor that has not been part of the
framework is described to be important – strategy fit. Furthermore,
the factors strategic alliances and platform strategy appear in the
literature but in a different context compared to the reference model.
Abstract: Our sowing date experiment took place in the
Demonstration Garden of Institution of Plant Sciences, Centre for
Agricultural Sciences of University of Debrecen, in 2012-2014. The
paper contains data of test year 2014. Our purpose, besides several
other examinations, was to observe how sowing date influences the
leaf area index and the activity of photosynthesis of maize hybrids,
and how those factors affect fruiting. In the experiment we monitored
the change of the leaf area index and the photosynthesis of hybrids
with four different growing seasons. The results obtained confirm
that not only the environmental and agricultural factors in the
growing season have effect on the yield, but also other factors like
the leaf area index and the photosynthesis are determinative
parameters, and all those factors together, modifying the effects of
each other, develop average yields.
Abstract: Natural admixtures provide concrete with enhanced
properties but their processing end up making them very expensive
resulting in increase to cost of concrete. In this study the effect
of Gum from Acacia Karroo (GAK) as set-retarding admixture
in cement pastes was studied. The possibility of using GAK as
water reducing admixture both in cement mortar concrete was
also investigated. Cement pastes with different dosages of GAK
were prepared to measure the setting time using different dosages.
Compressive strength of cement mortars with 0.7, 0.8 and 0.9%
weight of cement and w/c ratio of 0.5 were compared to those with
water cement (w/c) ratio of 0.44 but same dosage of GAK. Concrete
samples were prepared using higher dosages of GAK (1, 2 and 3%
wt of cement) and a water bidder (w/b) of 0.61 were compared to
those with the same GAK dosage but with reduced w/b ratio. There
was increase in compressive strength of 9.3% at 28 days for cement
mortar samples with 0.9% dosage of GAK and reduced w/c ratio.
Abstract: This article presents an alternative collapse capacity
intensity measure in the three elements form which is influenced by
the spectral ordinates at periods longer than that of the first mode
period at near and far source sites. A parameter, denoted by β, is
defined by which the spectral ordinate effects, up to the effective
period (2T1), on the intensity measure are taken into account. The
methodology permits to meet the hazard-levelled target extreme
event in the probabilistic and deterministic forms. A MATLAB code
is developed involving OpenSees to calculate the collapse capacities
of the 8 archetype RC structures having 2 to 20 stories for regression
process. The incremental dynamic analysis (IDA) method is used to
calculate the structure’s collapse values accounting for the element
stiffness and strength deterioration. The general near field set
presented by FEMA is used in a series of performing nonlinear
analyses. 8 linear relationships are developed for the 8structutres
leading to the correlation coefficient up to 0.93. A collapse capacity
near field prediction equation is developed taking into account the
results of regression processes obtained from the 8 structures. The
proposed prediction equation is validated against a set of actual near
field records leading to a good agreement. Implementation of the
proposed equation to the four archetype RC structures demonstrated
different collapse capacities at near field site compared to those of
FEMA. The reasons of differences are believed to be due to
accounting for the spectral shape effects.
Abstract: An experimental study with four different types of bed
conditions was carried out to understand the effect of roughness in
open channel flow at two different Reynolds numbers. The bed
conditions include a smooth surface and three different roughness
conditions, which were generated using sand grains with a median
diameter of 2.46 mm. The three rough conditions include a surface
with distributed roughness, a surface with continuously distributed
roughness and a sand bed with a permeable interface. A commercial
two-component fibre-optic LDA system was used to conduct the
velocity measurements. The variables of interest include the mean
velocity, turbulence intensity, correlation between the streamwise and
the wall normal turbulence, Reynolds shear stress and velocity triple
products. Quadrant decomposition was used to extract the magnitude
of the Reynolds shear stress of the turbulent bursting events. The
effect of roughness was evident throughout the flow depth. The
results show that distributed roughness has the greatest roughness
effect followed by the sand bed and the continuous roughness.
Compared to the smooth bed, the streamwise turbulence intensity
reduces but the vertical turbulence intensity increases at a location
very close to the bed due to the introduction of roughness. Although
the same sand grain is used to create the three different rough bed
conditions, the difference in the turbulence intensity is an indication
that the specific geometry of the roughness has an influence on
turbulence structure.
Abstract: Construction industry plays a vital role in the
economy of the world. However, due to high uncertainty and
variability in the industry, its performance is not as efficient in terms
of quality, lead times, productivity and costs as of other industries.
Moreover, there are continuous conflicts among the different actors
in the construction supply chains in terms of profit sharing. Previous
studies suggested partnership as an important approach to promote
cooperation among the different actors in the construction supply
chains and thereby it improves the overall performance. Construction
practitioners tried to focus on partnership which can enhance the
performance of construction supply chains but they are not fully
aware of different approaches and techniques for improving
partnership. In this research, a systematic review on partnership in
relation to construction supply chains is carried out to understand
different elements influencing the partnership. The research
development of this domain is analyzed by reviewing selected
articles published from 1996 to 2015. Based on the papers, three
major elements influencing partnership in construction supply chains
are identified: ‘Lean approach’, ‘Relationship building’ and ‘E-commerce
applications’. This study analyses the contributions in the
areas within each element and provides suggestions for future
developments of partnership in construction supply chains.
Abstract: In the present study we have investigated axial
buckling characteristics of nanocomposite beams reinforced by
single-walled carbon nanotubes (SWCNTs). Various types of beam
theories including Euler-Bernoulli beam theory, Timoshenko beam
theory and Reddy beam theory were used to analyze the buckling
behavior of carbon nanotube-reinforced composite beams.
Generalized differential quadrature (GDQ) method was utilized to
discretize the governing differential equations along with four
commonly used boundary conditions. The material properties of the
nanocomposite beams were obtained using molecular dynamic (MD)
simulation corresponding to both short-(10,10) SWCNT and long-
(10,10) SWCNT composites which were embedded by amorphous
polyethylene matrix. Then the results obtained directly from MD
simulations were matched with those calculated by the mixture rule
to extract appropriate values of carbon nanotube efficiency
parameters accounting for the scale-dependent material properties.
The selected numerical results were presented to indicate the
influences of nanotube volume fractions and end supports on the
critical axial buckling loads of nanocomposite beams relevant to
long- and short-nanotube composites.