Abstract: Microstructure, wetting behavior and interfacial
reactions between Sn–0.7Cu and Sn–0.3Ag–0.7Cu (SAC0307)
solders solidified on Ni coated Al substrates were compared and
investigated. Microstructure of Sn–0.7Cu alloy exhibited a eutectic
matrix composed of primary β-Sn dendrites with a fine dispersion of
Cu6Sn5 intermetallics whereas microstructure of SAC0307 alloy
exhibited coarser Cu6Sn5 and finer Ag3Sn precipitates of IMCs with
decreased tin dendrites. Contact angles ranging from 22° to 26° were
obtained for Sn–0.7Cu solder solidified on substrate surface whereas
for SAC0307 solder alloy contact angles were found to be in the
range of 20° to 22°. Sn–0.7Cu solder/substrate interfacial region
exhibited faceted (Cu, Ni)6Sn5 IMCs protruding into the solder matrix
and a small amount of (Cu, Ni)3Sn4 intermetallics at the interface.
SAC0307 solder/substrate interfacial region showed mainly (Cu,
Ni)3Sn4 intermetallics adjacent to the coating layer and (Cu,
Ni)6Sn5 IMCs in the solder matrix. The improvement in the
wettability of SAC0307 solder alloy on substrate surface is attributed
to the formation of cylindrical shape (Cu,Ni)6Sn5 and a layer of
(Cu, Ni)3Sn4 IMCs at the interface.
Abstract: Two completely different approaches for a Gigabit
Ethernet compliant stream transmission over 50m of 1mm PMMA SI-POF have been experimentally demonstrated and are compared in this paper. The first solution is based on a commercial RC-LED
transmission and a careful optimization of the physical layer architecture, realized during the POF-PLUS EU Project. The second solution exploits the performance of an edge-emitting laser at the
transmitter side in order to avoid any sort of electrical equalization at the receiver side.
Abstract: Processing the data by computers and performing
reasoning tasks is an important aim in Computer Science. Semantic
Web is one step towards it. The use of ontologies to enhance the
information by semantically is the current trend. Huge amount of
domain specific, unstructured on-line data needs to be expressed in
machine understandable and semantically searchable format.
Currently users are often forced to search manually in the results
returned by the keyword-based search services. They also want to use
their native languages to express what they search. In this paper, an
ontology-based automated question answering system on software
test documents domain is presented. The system allows users to enter
a question about the domain by means of natural language and
returns exact answer of the questions. Conversion of the natural
language question into the ontology based query is the challenging
part of the system. To be able to achieve this, a new algorithm
regarding free text to ontology based search engine query conversion
is proposed. The algorithm is based on investigation of suitable
question type and parsing the words of the question sentence.
Abstract: The use of solar control film on windows as one of
solar passive strategies for building have becoming important and is
gaining recognition. Malaysia located close to equator is having
warm humid climate with long sunshine hours and abundant solar
radiation throughout the year. Hence, befitting solar control on
windows is absolutely necessary to capture the daylight whilst
moderating thermal impact and eliminating glare problems. This is
one of the energy efficient strategies to achieve thermal and visual
comfort in buildings. Therefore, this study was carried out to
investigate the effect of window solar controls on thermal and visual
performance of naturally ventilated buildings. This was conducted via
field data monitoring using a test building facility. Four types of
window glazing systems were used with three types of solar control
films. Data were analysed for thermal and visual impact with
reference to thermal and optical characteristics of the films. Results
show that for each glazing system, the surface temperature of
windows are influenced by the Solar Energy Absorption property, the
indoor air temperature are influenced by the Solar Energy
Transmittance and Solar Energy Reflectance, and the daylighting by
Visible Light Transmission and Shading Coefficient. Further
investigations are underway to determine the mathematical relation
between thermal energy and visual performance with the thermal and
optical characteristics of solar control films.
Abstract: Effect of temperature and light was investigated on a
thin film of organic semiconductor formyl-TIPPCu(II) deposited on a
glass substrate with preliminary evaporated gold electrodes. The
electrical capacitance and resistance of the fabricated device were
evaluated under the effect of temperature and light. The relative
capacitance of the fabricated sensor increased by 4.3 times by rising
temperature from 27 to 1870C, while under illumination up to 25000
lx, the capacitance of the Au/formyl-TIPPCu(II)/Au photo capacitive
sensor increased continuously by 13.2 times as compared to dark
conditions.
Abstract: In this work, we present a novel active learning approach
for learning a visual object detection system. Our system
is composed of an active learning mechanism as wrapper around
a sub-algorithm which implement an online boosting-based learning
object detector. In the core is a combination of a bootstrap procedure
and a semi automatic learning process based on the online boosting
procedure. The idea is to exploit the availability of classifier during
learning to automatically label training samples and increasingly
improves the classifier. This addresses the issue of reducing labeling
effort meanwhile obtain better performance. In addition, we propose
a verification process for further improvement of the classifier.
The idea is to allow re-update on seen data during learning for
stabilizing the detector. The main contribution of this empirical study
is a demonstration that active learning based on an online boosting
approach trained in this manner can achieve results comparable or
even outperform a framework trained in conventional manner using
much more labeling effort. Empirical experiments on challenging data
set for specific object deteciton problems show the effectiveness of
our approach.
Abstract: In this study, to accurately predict cavitation of a
centrifugal pump, numerical analysis was compared with experimental
results modeled on a small industrial centrifugal pump. In this study,
numerical analysis was compared with experimental results modeled
on a small industrial centrifugal pump for reliable prediction on
cavitation of a centrifugal pump. To improve validity of the numerical
analysis, transient analysis was conducted on the calculated domain of
full-type geometry, such as an experimental apparatus. The numerical
analysis from the results was considered to be a reliable prediction of
cavitaion.
Abstract: Direct Torque Control is a control technique in AC
drive systems to obtain high performance torque control. The
conventional DTC drive contains a pair of hysteresis comparators.
DTC drives utilizing hysteresis comparators suffer from high torque
ripple and variable switching frequency. The most common solution
to those problems is to use the space vector depends on the reference
torque and flux. In this Paper The space vector modulation technique
(SVPWM) is applied to 2 level inverter control in the proposed
DTC-based induction motor drive system, thereby dramatically
reducing the torque ripple. Then the controller based on space vector
modulation is designed to be applied in the control of Induction
Motor (IM) with a three-level Inverter. This type of Inverter has
several advantages over the standard two-level VSI, such as a greater
number of levels in the output voltage waveforms, Lower dV/dt, less
harmonic distortion in voltage and current waveforms and lower
switching frequencies. This paper proposes a general SVPWM
algorithm for three-level based on standard two-level SVPWM. The
proposed scheme is described clearly and simulation results are
reported to demonstrate its effectiveness. The entire control scheme is
implemented with Matlab/Simulink.
Abstract: Glazing is a process used to reduce undesirable drying or dehydration of fish during frozen or cold storage. To evaluate the effect of the time/ temperature binomial of the cryogenic frozen tunnel in the amount of glazing watera Central Composite Rotatable Design was used, with application of the Response Surface Methodology. The results reveal that the time/ temperature obtained for pink cusk-eel in experimental conditions for glazing water are similar to the industrial process, but for red fish and merluza the industrial process needs some adjustments. Control charts were established and implementedto control the amount of glazing water on sardine and merluza. They show that the freezing process was statistically controlled but there were some tendencies that must be analyzed, since the trend of sample mean values approached either of the limits, mainly in merluza. Thus, appropriate actions must be taken, in order to improve the process.
Abstract: The combustion chamber dimensions have important
effects on pollutant emission in furnaces as a direct result of
temperature distribution and maximum temperature value. In this
paper the pollutant emission and the temperature distribution in two
cylindrical furnaces with different dimensions (with similar length to
diameter ratio) in similar condition have been investigated
experimentally. The furnace fuel is gas oil that is used with three
different flow rates. The results show that in these two cases the
temperature increases to its maximum value quickly, and then
decreases slowly. The results also show that increase in fuel flow rate
cause to increase in NOx emission in each case, but this increase is
greater in small furnace. With increase in fuel flow rate, CO emission
decreases firstly, and then it increases. Combustion efficiency
reduces with increase in fuel flow rate but the rate of reduction in
small furnace is greater than large furnace. The results of axial
temperature distribution have been compared with those have been
obtained numerically and experimentally by Moghiman.
Abstract: A fault detection and identification (FDI) technique is
presented to create a fault tolerant control system (FTC). The fault
detection is achieved by monitoring the position of the light source
using an array of light sensors. When a decision is made about the
presence of a fault an identification process is initiated to locate the
faulty component and reconfigure the controller signals. The signals
provided by the sensors are predictable; therefore the existence of a
fault is easily identified. Identification of the faulty sensor is based on
the dynamics of the frame. The technique is not restricted to a
particular type of controllers and the results show consistency.
Abstract: Reverse Engineering is a very important process in
Software Engineering. It can be performed backwards from system
development life cycle (SDLC) in order to get back the source data
or representations of a system through analysis of its structure,
function and operation. We use reverse engineering to introduce an
automatic tool to generate system requirements from its program
source codes. The tool is able to accept the Cµ programming source
codes, scan the source codes line by line and parse the codes to
parser. Then, the engine of the tool will be able to generate system
requirements for that specific program to facilitate reuse and
enhancement of the program. The purpose of producing the tool is to
help recovering the system requirements of any system when the
system requirements document (SRD) does not exist due to
undocumented support of the system.
Abstract: In this paper, a novel method for a biometric system based on the ECG signal is proposed, using spectral coefficients computed through linear predictive coding (LPC). ECG biometric systems have traditionally incorporated characteristics of fiducial points of the ECG signal as the feature set. These systems have been shown to contain loopholes and thus a non-fiducial system allows for tighter security. In the proposed system, incorporating non-fiducial features from the LPC spectrum produced a segment and subject recognition rate of 99.52% and 100% respectively. The recognition rates outperformed the biometric system that is based on the wavelet packet decomposition (WPD) algorithm in terms of recognition rates and computation time. This allows for LPC to be used in a practical ECG biometric system that requires fast, stringent and accurate recognition.
Abstract: Turbulent heat transfer to fluid flow through channel with triangular ribs of different angles are presented in this paper. Ansys 14 ICEM and Ansys 14 Fluent are used for meshing process and solving Navier stokes equations respectively. In this investigation three angles of triangular ribs with the range of Reynolds number varied from 20000 to 60000 at constant surface temperature are considered. The results show that the Nusselt number increases with the increase of Reynolds number for all cases at constant surface temperature. According to the profile of local Nusselt number on ribs walled of channel, the peak is at the midpoint between the two ribs. The maximum value of average Nusselt number is obtained for triangular ribs of angel 60°and at Reynolds number of 60000 compared to the Nusselt number for the ribs of angel 90° and 45° and at same Reynolds number. The recirculation regions generated by the ribs corresponding to the velocity streamline show the largest recirculation region at triangular ribs of angle 60° which also provides the highest enhancement of heat transfer.
Abstract: Seasonal variability of nutrients concentration in the Baltic Sea using the 3D ecosystem numerical model 3D-CEMBS has been investigated. Additionally this study shows horizontal and vertical distribution of nutrients in the Baltic Sea. Model domain is an extended Baltic Sea area divided into 600x640 horizontal grid cells. Aside from standard hydrodynamic parameters 3D-CEMBS produces modeled ecological variables such as: three types of phytoplankton, two detrital classes, dissolved oxygen and the nutrients (nitrate, ammonium, phosphate and silicate). The presented model allows prediction of parameters that describe distribution of nutrients concentration and phytoplankton biomass. 3D-CEMBS can be used to study the effect of different hydrodynamic and biogeochemical processes on distributions of these variables in a larger scale.
Abstract: In this paper, a two-dimensional mathematical model is developed for estimating the extent of inland inundation due to Indonesian tsunami of 2004 along the coastal belts of Peninsular Malaysia and Thailand. The model consists of the shallow water equations together with open and coastal boundary conditions. In order to route the water wave towards the land, the coastal boundary is treated as a time dependent moving boundary. For computation of tsunami inundation, the initial tsunami wave is generated in the deep ocean with the strength of the Indonesian tsunami of 2004. Several numerical experiments are carried out by changing the slope of the beach to examine the extent of inundation with slope. The simulated inundation is found to decrease with the increase of the slope of the orography. Correlation between inundation / recession and run-up are found to be directly proportional to each other.
Abstract: Streamribbon is used to visualize the rotation of the
fluid flow. The rotation of flow is useful in fluid mechanics,
engineering and geophysics. This paper introduces the construction
technique of streamribbon using the streamline which is generated
based on the law of mass conservation. The accuracy of constructed
streamribbons is shown through two examples.
Abstract: In this paper, an artificial neural network simulator is
employed to carry out diagnosis and prognosis on electric motor as
rotating machinery based on predictive maintenance. Vibration data
of the primary failed motor including unbalance, misalignment and
bearing fault were collected for training the neural network. Neural
network training was performed for a variety of inputs and the motor
condition was used as the expert training information. The main
purpose of applying the neural network as an expert system was to
detect the type of failure and applying preventive maintenance. The
advantage of this study is for machinery Industries by providing
appropriate maintenance that has an essential activity to keep the
production process going at all processes in the machinery industry.
Proper maintenance is pivotal in order to prevent the possible failures
in operating system and increase the availability and effectiveness of
a system by analyzing vibration monitoring and developing expert
system.
Abstract: There are extensive applications of lithium
bromide-water absorption chillers in industry, but the heat exchangers
corrosion and refrigerating capacity loss are very difficult to be solved.
In this paper, an experiment was conducted by using plastic heat
transfer tubes instead of copper tubes. As an example, for a lithium
bromide-water absorption chiller of refrigerating capacity of 35kW,
the correlative performance of the lithium bromide-water absorption
chiller using plastic heat transfer tubes was compared with the
traditional lithium bromide-water absorption chiller. And then the
following three aspects, i.e., heat transfer area, pipe resistance, and
safety strength, are analyzed. The results show that plastic heat
transfer tubes can be used on lithium bromide-water absorption
chillers, and its prospect is very optimistic.
Abstract: In this research, the researchers have managed to
design a model to investigate the current trend of stock price of the
"IRAN KHODRO corporation" at Tehran Stock Exchange by
utilizing an Adaptive Neuro - Fuzzy Inference system. For the Longterm
Period, a Neuro-Fuzzy with two Triangular membership
functions and four independent Variables including trade volume,
Dividend Per Share (DPS), Price to Earning Ratio (P/E), and also
closing Price and Stock Price fluctuation as an dependent variable are
selected as an optimal model. For the short-term Period, a neureo –
fuzzy model with two triangular membership functions for the first
quarter of a year, two trapezoidal membership functions for the
Second quarter of a year, two Gaussian combination membership
functions for the third quarter of a year and two trapezoidal
membership functions for the fourth quarter of a year were selected
as an optimal model for the stock price forecasting. In addition, three
independent variables including trade volume, price to earning ratio,
closing Stock Price and a dependent variable of stock price
fluctuation were selected as an optimal model. The findings of the
research demonstrate that the trend of stock price could be forecasted
with the lower level of error.