Abstract: The value of overall oxygen transfer Coefficient
(KLa), which is the best measure of oxygen transfer in water through
aeration, is obtained by a simple approach, which sufficiently
explains the utility of the method to eliminate the discrepancies due
to inaccurate assumption of saturation dissolved oxygen
concentration. The rate of oxygen transfer depends on number of
factors like intensity of turbulence, which in turns depends on the
speed of rotation, size, and number of blades, diameter and
immersion depth of the rotor, and size and shape of aeration tank, as
well as on physical, chemical, and biological characteristic of water.
An attempt is made in this paper to correlate the overall oxygen
transfer Coefficient (KLa), as an independent parameter with other
influencing parameters mentioned above. It has been estimated that
the simulation equation developed predicts the values of KLa and
power with an average standard error of estimation of 0.0164 and
7.66 respectively and with R2 values of 0.979 and 0.989 respectively,
when compared with experimentally determined values. The
comparison of this model is done with the model generated using
Computational fluid dynamics (CFD) and both the models were
found to be in good agreement with each other.
Abstract: The Pulsed Compression Reactor promises to be a
compact, economical and energy efficient alternative to conventional
chemical reactors.
In this article, the production of synthesis gas using the Pulsed
Compression Reactor is investigated. This is done experimentally as
well as with simulations. The experiments are done by means of a
single shot reactor, which replicates a representative, single
reciprocation of the Pulsed Compression Reactor with great control
over the reactant composition, reactor temperature and pressure and
temperature history. Simulations are done with a relatively simple
method, which uses different models for the chemistry and
thermodynamic properties of the species in the reactor. Simulation
results show very good agreement with the experimental data, and
give great insight into the reaction processes that occur within the
cycle.
Abstract: The Beshar River is one aquatic ecosystem, which is
located next to the city of Yasuj in southern Iran. The Beshar river
has been contaminated by industrial factories such as effluent of
sugar factory, agricultural and other activities in this region such as,
Imam Sajjad hospital, drainage from agricultural farms, Yasuj urban
surface runoff and effluent of wastewater treatment plants ,specially
Yasuj waste water treatment plant. In order to evaluate the effects of
these pollutants on the quality of the Beshar river, five monitoring
stations were selected along its course. The first station is located
upstream of Yasuj near the Dehnow village; stations 2 to 4 are
located east, south and west of city; and the 5th station is located
downstream of Yasuj. Several water quality parameters were
sampled. These include pH, dissolved oxygen, biological oxygen
demand (BOD), temperature, conductivity, turbidity, total dissolved
solids and discharge or flow measurements. Water samples from the
five stations were collected and analyzed to determine the following
physicochemical parameters: EC, pH, T.D.S, T.H, No2, DO, BOD5,
COD during 2008 to 2010. The study shows that the BOD5 value of
station 1 is at a minimum (1.7 ppm) and increases downstream from
stations 2 to 4 to a maximum (11.6 ppm), and then decreases at
station 5. The DO values of station 1 is a maximum (8.45 ppm),
decreases downstream to stations 2 - 4 which are at a minimum (3.1
ppm), before increasing at station 5. The amount of BOD and TDS
are highest at the 4th station and the amount of DO is lowest at this
station, marking the 4th station as more highly polluted than the
other stations .This study shows average amount of the water quality
parameters in first year of sampling (2008) have had a better quality
relation to third year in 2010 because of recent drought in this region
and pollutant increasing .As the Beshar river path after 5th station
goes through the mountain area with more slope and flow velocity
,so the physicochemical parameters improve at the 5th station due to
pollutant degradation and dilution. Finally the point and nonpoint
pollutant sources of Beshar river were determined and compared to
the monitoring results.
Abstract: Some physico-chemical characteristics and mineral
composition of 'Karayemis' (Prunus laurocerasus L.) fruits which
grown naturally in Norteast Turkey was studied. 28 minerals ( Al,
Mg, B, Mn, Co, Na, Ca, Ni, Cd, P, Cr, Pb, Cu, S, Fe, Zn, K, Sr, Li,
As, V, Ag, Ba, Br, Ga, In, Se, Ti) were analyzed and 19 minerals
were present at ascertainable levels. Karayemis fruit was richest in
potassium (7938.711 ppm), magnesium (1242.186 ppm) and calcium
(1158.853 ppm). And some physico-chemical characteristics of
Karayemis fruit was investigated. Fruit length, fruit width, fruit
thickness, fruit weight, total soluble solids, colour, protein, crude ash,
crude fiber, crude oil values were determined as 2.334 cm, 1.884 cm,
2.112 cm, 5.35 g, 20.1 %, S99M99Y99, 0.29 %, 0.22 %, 6.63 % and
0.001 %, respectively. The seed of fruit mean weight, length, width
and thickness were found to be 0.41 g, 1.303 cm, 0.921 cm and
0.803, respectively.
Abstract: Antimosy-doped tin oxide (ATO) particles were
prepared via chemical coprecipitation and reverse emulsion. The size
and size distribution of ATO particles were obviously decreased via
reverse microemulsion method. At the relatively high yield the ATO
particles were nearly spherical in shape, meanwhile the crystalline
structure and excellent conductivity were reserved, which could satisfy
the requirement as composite fillers, such as dielectric filler of
polyimide film.
Abstract: There have been widespread applications of fluidized beds in industries which are related to the combination of gas-solid particles during the last decade. For instance, in order to crack the catalyses in petrochemical industries or as a drier in food industries. High capacity of fluidized bed in heat and mass transfer has made this device very popular. In order to achieve a higher efficiency of fluidized beds, a particular attention has been paid to beds with pulsating air flow. In this paper, a fluidized bed device with pulsating flow has been designed and constructed. Size of particles have been used during the test are in the range of 40 to 100μm. The purpose of this experimental test is to investigate the air flow regime, observe the particles- movement and measure the pressure loss along the bed. The effects of pulsation can be evaluated by comparing the results for both continuous and pulsating flow. Results of both situations are compared for various gas speeds. Moreover the above experiment is numerically simulated by using Fluent software and its numerical results are compared with the experimental results.
Abstract: Mechanical interaction between endothelial cells (ECs) and the extracellular matrix (or collagen gel) is known to influence the sprouting response of endothelial cells during angiogenesis. This influence is believed to impact on the capability of endothelial cells to sense soluble chemical cues. Quantitative analysis of endothelial-cell-mediated displacement of the collagen gel provides a means to explore this mechanical interaction. Existing analysis in this context is generally limited to 2D settings. In this paper, we investigate the mechanical interaction between endothelial cells and the extracellular matrix in terms of the endothelial-cellmediated displacement of the collagen gel in both 2D and 3D. Digital image correlation and Digital volume correlation are applied on confocal reflectance image stacks to analyze cell-mediated displacement of the gel. The skeleton of the sprout is extracted from phase contrast images and superimposed on the displacement field to further investigate the link between the development of the sprout and the displacement of the gel.
Abstract: Hepatitis C is an infectious disease transmitted by
blood and due to hepatitis C virus (HCV), which attacks the liver.
The infection is characterized by liver inflammation (hepatitis) that is
often asymptomatic but can progress to chronic hepatitis and later
cirrhosis and liver cancer. Our problem tends to highlight on the one
hand the prevalence of infectious disease in the population of the
region of Batna and on other hand the biological characteristics of
this disease by a screening and a specific diagnosis based on
serological tests, liver checkup (measurement of haematological and
biochemical parameters).
The results showed:
The serology of hepatitis C establishes the diagnosis of infection
with hepatitis C. In this study and with the serological test, 24 cases
of the disease of hepatitis C were found in 1000 suspected cases (7
cases with normal transaminases and 17 cases with elevated
transaminases). The prevalence of this disease in this study
population was 2.4%.
The presence of hepatitis C disrupts liver function including the
onset of cytolysis, cholestasis, jaundice, thrombocytopenia, and
coagulation disorders.
Abstract: The mineral having chemical compositional formula MgAl2O4 is called “spinel". The ferrites crystallize in spinel structure are known as spinel-ferrites or ferro-spinels. The spinel structure has a fcc cage of oxygen ions and the metallic cations are distributed among tetrahedral (A) and octahedral (B) interstitial voids (sites). The X-ray diffraction (XRD) intensity of each Bragg plane is sensitive to the distribution of cations in the interstitial voids of the spinel lattice. This leads to the method of determination of distribution of cations in the spinel oxides through XRD intensity analysis. The computer program for XRD intensity analysis has been developed in C language and also tested for the real experimental situation by synthesizing the spinel ferrite materials Mg0.6Zn0.4AlxFe2- xO4 and characterized them by X-ray diffractometry. The compositions of Mg0.6Zn0.4AlxFe2-xO4(x = 0.0 to 0.6) ferrites have been prepared by ceramic method and powder X-ray diffraction patterns were recorded. Thus, the authenticity of the program is checked by comparing the theoretically calculated data using computer simulation with the experimental ones. Further, the deduced cation distributions were used to fit the magnetization data using Localized canting of spins approach to explain the “recovery" of collinear spin structure due to Al3+ - substitution in Mg-Zn ferrites which is the case if A-site magnetic dilution and non-collinear spin structure. Since the distribution of cations in the spinel ferrites plays a very important role with regard to their electrical and magnetic properties, it is essential to determine the cation distribution in spinel lattice.
Abstract: Perth will run out of available sustainable natural
water resources by 2015 if nothing is done to slow usage rates,
according to a Western Australian study [1]. Alternative water
technology options need to be considered for the long-term
guaranteed supply of water for agricultural, commercial, domestic
and industrial purposes. Seawater is an alternative source of water for
human consumption, because seawater can be desalinated and
supplied in large quantities to a very high quality.
While seawater desalination is a promising option, the technology
requires a large amount of energy which is typically generated from
fossil fuels. The combustion of fossil fuels emits greenhouse gases
(GHG) and, is implicated in climate change. In addition to
environmental emissions from electricity generation for desalination,
greenhouse gases are emitted in the production of chemicals and
membranes for water treatment. Since Australia is a signatory to the
Kyoto Protocol, it is important to quantify greenhouse gas emissions
from desalinated water production.
A life cycle assessment (LCA) has been carried out to determine
the greenhouse gas emissions from the production of 1 gigalitre (GL)
of water from the new plant. In this LCA analysis, a new desalination
plant that will be installed in Bunbury, Western Australia, and known
as Southern Seawater Desalinization Plant (SSDP), was taken as a
case study. The system boundary of the LCA mainly consists of three
stages: seawater extraction, treatment and delivery. The analysis
found that the equivalent of 3,890 tonnes of CO2 could be emitted
from the production of 1 GL of desalinated water. This LCA analysis
has also identified that the reverse osmosis process would cause the
most significant greenhouse emissions as a result of the electricity
used if this is generated from fossil fuels
Abstract: Wastages such as grated coconut meat, spent tea and used sugarcane had contributed negative impacts to the environment. Vermicomposting method is fully utilized to manage the wastes towards a more sustainable approach. The worms that are used in the vermicomposting are Eisenia foetida and Eudrillus euginae. This research shows that the vermicompost of wastages has voltage of electrical energy and is able to light up the Light-Emitting Diode (LED) device. Based on the experiment, the use of replicated and double compartments of the component will produce double of voltage. Hence, for conclusion, this harmless and low cost technology of vermicompost can act as a dry cell in order to reduce the usage of hazardous chemicals that can contaminate the environment.
Abstract: A spectrophotometric method was developed for simultaneous quantification of pseudoephedrine hydrochloride (PSE) triprolidine hydrochloride (TRI) using second derivative method (zero-crossing technique). The second derivative amplitudes of PSE and TRI were measured at 271 and 321 nm, respectively. The calibration curves were linear in the range of 200 to 1,000 g/ml for PSE and 10 to 50 g/ml for TRI. The method was validated for specificity, accuracy, precision, limit of detection and limit of quantitation. The proposed method was applied to the assaying and dissolution of PSE and TRI in commercial tablets without any chemical separation. The results were compared with those obtained by the official USP31 method and statistical tests showed that there is no significant between the methods at 95% confidence level. The proposed method is simple, rapid and suitable for the routine quality control application. KeywordsTriprolidine, Pseudoephedrine, Derivative spectrophotometry, Dissolution testing.
Abstract: The utilization of cheese whey as a fermentation
substrate to produce bio-ethanol is an effort to supply bio-ethanol
demand as a renewable energy. Like other process systems, modeling
is also required for fermentation process design, optimization and
plant operation. This research aims to study the fermentation process
of cheese whey by applying mathematics and fundamental concept in
chemical engineering, and to investigate the characteristic of the
cheese whey fermentation process. Steady state simulation results for
inlet substrate concentration of 50, 100 and 150 g/l, and various
values of hydraulic retention time, showed that the ethanol
productivity maximum values were 0.1091, 0.3163 and 0.5639 g/l.h
respectively. Those values were achieved at hydraulic retention time
of 20 hours, which was the minimum value used in this modeling.
This showed that operating reactor at low hydraulic retention time
was favorable. Model of bio-ethanol production from cheese whey
will enhance the understanding of what really happen in the
fermentation process.
Abstract: An implant elicits a biological response in the
surrounding tissue which determines the acceptance and long-term
function of the implant. Dental implants have become one of the
main therapy methods in clinic after teeth lose. A successful implant
is in contact with bone and soft tissue represent by fibroblasts. In our
study we focused on the interaction between six different chemically
and physically modified titanium implants (Tis-MALP, Tis-O, Tis-
OA, Tis-OPAAE, Tis-OZ, Tis-OPAE) with alveolar fibroblasts as
well as with five type of microorganisms (S. epidermis, S.mutans, S.
gordonii, S. intermedius, C.albicans). The analysis of microorganism
adhesion was determined by CFU (colony forming unite) and biofilm
formation. The presence of α3β1 and vinculin expression on alveolar
fibroblasts was demonstrated using phospho specific cell based
ELISA (PACE). Alveolar fibroblasts have the highest expression of
these proteins on Tis-OPAAE and Tis-OPAE. It corresponds with
results from bacterial adhesion and biofilm formation and it was
related to the lowest production of collagen I by alveolar fibroblasts
on Tis-OPAAE titanium disc.
Abstract: Carbon disulfide is widely used for the production of
viscose rayon, rubber, and other organic materials and it is a
feedstock for the synthesis of sulfuric acid. The objective of this
paper is to analyze possibilities for efficient production of CS2 from
sour natural gas reformation (H2SMR) (2H2S+CH4 =CS2 +4H2) .
Also, the effect of H2S to CH4 feed ratio and reaction temperature on
carbon disulfide production is investigated numerically in a
reforming reactor. The chemical reaction model is based on an
assumed Probability Density Function (PDF) parameterized by the
mean and variance of mixture fraction and β-PDF shape. The results
show that the major factors influencing CS2 production are reactor
temperature. The yield of carbon disulfide increases with increasing
H2S to CH4 feed gas ratio (H2S/CH4≤4). Also the yield of C(s)
increases with increasing temperature until the temperature reaches
to 1000°K, and then due to increase of CS2 production and
consumption of C(s), yield of C(s) drops with further increase in the
temperature. The predicted CH4 and H2S conversion and yield of
carbon disulfide are in good agreement with result of Huang and TRaissi.
Abstract: Measurement of the COD of a spent caustic solution involves firstly digestion of a test sample with dichromate solution and secondly measurement of dichromate remained by titration by ferrous ammonium sulfate [FAS] to an end point. In this paper we study by a potentiometric end point with Ag/AgCl reference electrode and gold rode electrode. The potentiometric end point is sharp and easily identified especially for the samples with high turbidity and color that other methods such as colorimetric in this type of sample do not result in high precision. Because interim of titration responds quickly to potential changes within the [Cr+6/Cr+3& Fe+2/Fe+3] solution producing stable readings that is lead to accurate COD measurement. Finally results are compared with data determined using colorimetric method for standard samples. It is shown that the potentiometric end point titration with gold rode electrode can be used with equal or better facility
Abstract: Cenozoic basalts found in Jiangsu province of eastern
China include tholeiites and alkali basalts. The present paper analyzed
the major, trace elements, rare earth elements of these Cenozoic
basalts and combined with Sr-Nd isotopic compositions proposed by
Chen et al. (1990)[1] in the literatures to discuss the petrogenesis of
these basalts and the geochemical characteristics of the source mantle.
Based on major, trace elements and fractional crystallization model
established by Brooks and Nielsen (1982)[2] we suggest that the
basaltic magma has experienced olivine + clinopyroxene fractionation
during its evolution. The chemical compositions of basaltic rocks from
Jiangsu province indicate that these basalts may belong to the same
magmatic system. Spidergrams reveal that Cenozoic basalts from
Jiangsu province have geochemical characteristics similar to those of
ocean island basalts(OIB). The slight positive Nb and Ti anomalies
found in basaltic rocks of this study suggest the presence of Ti-bearing
minerals in the mantle source and these Ti-bearing minerals had
contributed to basaltic magma during partial melting, indicating a
metasomatic event might have occurred before the partial melting.
Based on the Sr vs. Nd isotopic ratio plots, we suggest that Jiangsu
basalts may be derived from partial melting of mantle source which
may represent two-end members mixing of DMM and EM-I. Some
Jiangsu basaltic magma may be derived from partial melting of EM-I
heated by the upwelling asthenospheric mantle or asthenospheric
diapirism.
Abstract: Carbon nanotubes (CNTs) with their high mechanical,
electrical, thermal and chemical properties are regarded as promising
materials for many different potential applications. Having unique
properties they can be used in a wide range of fields such as
electronic devices, electrodes, drug delivery systems, hydrogen
storage, textile etc. Catalytic chemical vapor deposition (CCVD) is a
common method for CNT production especially for mass production.
Catalysts impregnated on a suitable substrate are important for
production with chemical vapor deposition (CVD) method. Iron
catalyst and MgO substrate is one of most common catalyst-substrate
combination used for CNT. In this study, CNTs were produced by
CCVD of acetylene (C2H2) on magnesium oxide (MgO) powder
substrate impregnated by iron nitrate (Fe(NO3)3•9H2O) solution. The
CNT synthesis conditions were as follows: at synthesis temperatures
of 500 and 800°C multiwall and single wall CNTs were produced
respectively. Iron (Fe) catalysts were prepared by with Fe:MgO ratio
of 1:100, 5:100 and 10:100. The duration of syntheses were 30 and
60 minutes for all temperatures and catalyst percentages. The
synthesized materials were characterized by thermal gravimetric
analysis (TGA), transmission electron microscopy (TEM) and Raman
spectroscopy.
Abstract: The study was carried out to evaluated effect of S-gridling on fruit growth and quality of wax apple. The study was laid in Random completed block design with four replicated. Four treatment were applied as follows: S-girdling, fruit thinning plus bagging with 2,4-D sprayed, fruit thinning plus bagging and the control treatment. 2,4D was sprayed at the small bud and petal fall stage. Girdling was applied three week before flowering. The effect of all treatments on fruit growth was measured weekly. Number of flower, fruit set, fruit drop, fruit crack, and fruit quality were recorded. The result indicated that S-girdling, 2,4D application produced the lowest bud drop, fruit drop compared to untreated control. S-girdling improved faster fruit growth producing the best final fruit length and diameter compared to untreated control. S-girdling also markedly enhanced fruit set, fruit weight, and total soluble solid, reduced fruit crack, titratable acidity. On the other hand, it was noticed that with 2,4-D application also increased the fruit growth rate, improved physiological and biochemical characters of fruit than control treatment. It was concluded that S-girdling was recommended as the industry norm to increase fruit set, fruit quality in wax apple. 2,4D application had a distinctive and significant effect on most of the fruit quality characteristics assessed.
Abstract: Chlorine is one of the most abundant elements in
nature, which undergoes a complex biogeochemical cycle. Chlorine
bound in some substances is partly responsible for atmospheric ozone
depletion and contamination of some ecosystems. As due to
international regulations anthropogenic burden of volatile
organochlorines (VOCls) in atmosphere decreases, natural sources
(plants, soil, abiotic formation) are expected to dominate VOCl
production in the near future. Examples of plant VOCl production are
methyl chloride, and bromide emission from (sub)tropical ferns,
chloroform, 1,1,1-trichloroethane and tetrachloromethane emission
from temperate forest fern and moss. Temperate forests are found to
emit in addition to the previous compounds tetrachloroethene, and
brominated volatile compounds. VOCls can be taken up and further
metabolized in plants. The aim of this work is to identify and
quantitatively analyze the formed VOCls in temperate forest
ecosystems by a cryofocusing/GC-ECD detection method, hence
filling a gap of knowledge in the biogeochemical cycle of chlorine.