Abstract: Based on a global kinetics of direct dimethyl ether (DME) synthesis process from syngas, a steady-state one-dimensional mathematical model for the bubble column slurry reactor (BCSR) has been established. It was built on the assumption of plug flow of gas phase, sedimentation-dispersion model of catalyst grains and isothermal chamber regardless of reaction heats and rates for the design of an industrial scale bubble column slurry reactor. The simulation results indicate that higher pressure and lower temperature were favorable to the increase of CO conversion, DME selectivity, products yield and the height of slurry bed, which has a coincidence with the characteristic of DME synthesis reaction system, and that the height of slurry bed is lessen with the increasing of operation temperature in the range of 220-260℃. CO conversion, the optimal operation conditions in BCSR were proposed.
Abstract: For broadband wireless mobile communication
systems the orthogonal frequency division multiplexing (OFDM) is a
suitable modulation scheme. The frequency offset between
transmitter and receiver local oscillator is main drawback of OFDM
systems, which causes intercarrier interference (ICI) in the
subcarriers of the OFDM system. This ICI degrades the bit error rate
(BER) performance of the system. In this paper an improved self-ICI
cancellation scheme is proposed to improve the system performance.
The proposed scheme is based on discrete Fourier transform-inverse
discrete Fourier transform (DFT-IDFT). The simulation results show
that there is satisfactory improvement in the bit error rate (BER)
performance of the present scheme.
Abstract: This paper presents a large scale, quantitative investigation of the impact of discipline differences on the student experience of using an online learning environment (OLE). Based on a representative sample of 2526 respondents, a number of significant differences in the mean rating by broad discipline area of the importance of, and satisfaction with, a range of elements of an OLE were found. Broadly speaking, the Arts and Science and Technology discipline areas reported the lowest importance and satisfaction ratings for the OLE, while the Health and Behavioural Sciences area was the most satisfied with the OLE. A number of specific, systematic discipline differences are reported and discussed. Compared to the observed significant differences in mean importance ratings, there were fewer significant differences in mean satisfaction ratings, and those that were observed were less systematic than for importance ratings.
Abstract: Variations in the growth rate constant of the Listeria
monocytogenes bacterial species were determined at 37°C in
irradiated environments and compared to the situation of a nonirradiated
environment. The bacteria cells, contained in a suspension
made of a nutrient solution of Brain Heart Infusion, were made to
grow at different frequency (2.30e2.60 GHz) and power (0e400
mW) values, in a plug flow reactor positioned in the irradiated
environment. Then the reacting suspension was made to pass into a
cylindrical cuvette where its optical density was read every 2.5
minutes at a wavelength of 600 nm. The obtained experimental data
of optical density vs. time allowed the bacterial growth rate constant
to be derived; this was found to be slightly influenced by microwave
power, but not by microwave frequency; in particular, a minimum
value was found for powers in the 50e150 mW field.
Abstract: The V-notches are most possible case for initiation of cracks in parts. The specifications of cracks on the tip of the notch will be influenced via opening angle, tip radius and depth of V-notch. In this study, the effects of V-notch-s opening angle on stress intensity factor and T-stress of crack on the notch has been investigated. The experiment has been done in different opening angles and various crack length in mode (I) loading using Photoelasticity method. The results illustrate that while angle increases in constant crack-s length, SIF and T-stress will decrease. Beside, the effect of V-notch angle in short crack is more than long crack. These V-notch affects are negligible by increasing the length of crack, and the crack-s behavior can be considered as a single-edge crack specimen. Finally, the results have been evaluated with numerical finite element analysis and good agreement was obvious.
Abstract: A number of studies highlighted problems related to
ERP systems, yet, most of these studies focus on the problems during
the project and implementation stages but not during the postimplementation
use process. Problems encountered in the process of
using ERP would hinder the effective exploitation and the extended
and continued use of ERP systems and their value to organisations.
This paper investigates the different types of problems users
(operational, supervisory and managerial) faced in using ERP and
how 'feral system' is used as the coping mechanism. The paper
adopts a qualitative method and uses data collected from two cases
and 26 interviews, to inductively develop a casual network model of
ERP usage problem and its coping mechanism. This model classified
post ERP usage problems as data quality, system quality, interface
and infrastructure. The model is also categorised the different coping
mechanism through use of 'feral system' inclusive of feral
information system, feral data and feral use of technology.
Abstract: This research examines possible effects of climatic
change focusing on global warming and its impacts on world
agricultural product markets, by using a world food model developed
to consider climate changes. GDP and population for each scenario
were constructed by IPCC and climate data for each scenario was
reported by the Hadley Center and are used in this research to consider
results in different contexts. Production and consumption of primary
agriculture crops of the world for each socio-economic scenario are
obtained and investigated by using the modified world food model.
Simulation results show that crop production in some countries or
regions will have different trends depending on the context. These
alternative contexts depend on the rate of GDP growth, population,
temperature, and rainfall. Results suggest that the development of
environment friendly technologies lead to more consumption of food
in many developing countries. Relationships among environmental
policy, clean energy development, and poverty elimination warrant
further investigation.
Abstract: This paper proposes, implements and evaluates an original discretization method for continuous random variables, in order to estimate the reliability of systems for which stress and strength are defined as complex functions, and whose reliability is not derivable through analytic techniques. This method is compared to other two discretizing approaches appeared in literature, also through a comparative study involving four engineering applications. The results show that the proposal is very efficient in terms of closeness of the estimates to the true (simulated) reliability. In the study we analyzed both a normal and a non-normal distribution for the random variables: this method is theoretically suitable for each parametric family.
Abstract: Visible Light Communication (VLC) offers advantages of low energy consumption, licence free and RF interference free operation. One application area for VLC is in the provision of health centred services circumventing issues of interference with any biomedical device within the environment. VLC performamce is affected by natural light restricting systems avilability and relibility. The paper presents an analysis of the performance of VLC systems under different meteorological conditions. The evaluation considered the impact of natural light as a function of different reflection surfaces in different room sizes.
Abstract: The major objective of this study is to understand the
potential of a newly fabricated equipment to study the thermal
properties of nonwoven textile fabrics treated with aerogel at subzero
temperatures. Thermal conductivity was calculated by using the
empirical relation Fourier’s law, The relationship between the
thermal conductivity and thermal resistance of the samples were
studied at various environmental temperatures (which was set in the
clima temperature system between +25oC to -25oC). The newly
fabricated equipment was found to be a suitable for measuring at
subzero temperatures. This field of measurements is being developed
and will be the subject of further research which will be more suitable
for measurement of the various thermal characteristics.
Abstract: In the competitive environment of aircraft industries it becomes absolutely necessary to improve the efficiency, performance of the aircrafts to reduce the development and operating costs considerably, in order to capitalize the market. An important contribution to improve the efficiency and performance can be
achieved by decreasing the aircraft weight through considerable
usage of composite materials in primary aircraft structures. In this study, a type of composite material called Carbon Fiber Reinforced
Plastic (CFRP) is explored for the usage is aircraft skin panels. Even
though there were plenty of studies and research has been already
carried out, here a practical example of an aircraft skin panel is taken
and substantiated the benefits of composites material usage over the
metallic skin panel. A crown skin panel of a commercial aircraft is
designed using both metal and composite materials. Stress analysis
has been carried out for both and margin of safety is estimated for the
critical load cases. The skin panels are compared for manufacturing,
tooling, assembly and cost parameters. Detail step by step comparison between metal and composite constructions are studied
and results are tabulated for better understanding.
Abstract: In this paper, a new hybrid of genetic algorithm (GA)
and simulated annealing (SA), referred to as GSA, is presented. In
this algorithm, SA is incorporated into GA to escape from local
optima. The concept of hierarchical parallel GA is employed to
parallelize GSA for the optimization of multimodal functions. In
addition, multi-niche crowding is used to maintain the diversity in
the population of the parallel GSA (PGSA). The performance of the
proposed algorithms is evaluated against a standard set of multimodal
benchmark functions. The multi-niche crowding PGSA and normal
PGSA show some remarkable improvement in comparison with the
conventional parallel genetic algorithm and the breeder genetic
algorithm (BGA).
Abstract: The huge development of new technologies and the
apparition of open communication system more and more
sophisticated create a new challenge to protect digital content from
piracy. Digital watermarking is a recent research axis and a new
technique suggested as a solution to these problems. This technique
consists in inserting identification information (watermark) into
digital data (audio, video, image, databases...) in an invisible and
indelible manner and in such a way not to degrade original medium-s
quality. Moreover, we must be able to correctly extract the
watermark despite the deterioration of the watermarked medium (i.e
attacks). In this paper we propose a system for watermarking satellite
images. We chose to embed the watermark into frequency domain,
precisely the discrete wavelet transform (DWT). We applied our
algorithm on satellite images of Tunisian center. The experiments
show satisfying results. In addition, our algorithm showed an
important resistance facing different attacks, notably the compression
(JEPG, JPEG2000), the filtering, the histogram-s manipulation and
geometric distortions such as rotation, cropping, scaling.
Abstract: The author present PID controller design for
following control of hard disk drive by characteristic ratio assignment
method. The study in this paper concerns design of a PID controller
which sufficiently robust to the disturbances and plant perturbations
on following control of hard disk drive. Characteristic Ratio
Assignment (CRA) is shown to be an efficient control technique to
serve this requirement. The controller design by CRA is based on the
choice of the coefficients of the characteristic polynomial of the
closed loop system according to the convenient performance criteria
such as equivalent time constant and ration of characteristic
coefficient. Hence, in this study, CRA method is applied in PID
controller design for following control of hard disk drive. Matlab
simulation results shown that CRA design is fairly stable and robust
whilst giving the convenience in controller-s parameters adjustment.
Abstract: In literatures, many researches proposed various
methods to reduce PAPR (Peak to Average Power Ratio). Among
those, DSI (Dummy Sequence Insertion) is one of the most attractive
methods for WiMAX systems because it does not require side
information transmitted along with user data. However, the
conventional DSI methods find dummy sequence by performing an
iterative procedure until achieving PAPR under a desired threshold.
This causes a significant delay on finding dummy sequence and also
effects to the overall performances in WiMAX systems. In this paper,
the new method based on DSI is proposed by finding dummy
sequence without the need of iterative procedure. The fast DSI
method can reduce PAPR without either delays or required side
information. The simulation results confirm that the proposed method
is able to carry out PAPR performances as similar to the other
methods without any delays. In addition, the simulations of WiMAX
system with adaptive modulations are also investigated to realize the
use of proposed methods on various fading schemes. The results
suggest the WiMAX designers to modify a new Signal to Noise Ratio
(SNR) criteria for adaptation.
Abstract: In this paper we study a food chain model with three trophic levels and Michaelis-Menten type ratio-dependent functional response. Distinctive feature of this model is the sensitive dependence of the dynamical behavior on the initial populations and parameters of the real world. The stability of the equilibrium points are also investigated.
Abstract: On March 11, 2011, the East coast of Japan was hit by
one of the strongest earthquakes in history, followed by a devastating
tsunami. Although most lifelines, infrastructure, and public facilities
have been restored gradually, recovery efforts in terms of disposal of
disaster waste and revival of primary industry are lagging. This study
presents a summary of the damage inflicted by the earthquake and the
current status of reconstruction in the disaster area. Moreover, we
discuss the current trends and future perspectives on recently
implemented eco-friendly reconstruction projects and focus on the
pro-environmental behavior of disaster victims which is emerging as a
result of the energy shortage after the earthquake. Finally, we offer
ideas for initiatives for the next stage of the reconstruction policies.
Abstract: In recent years, we see an increase of interest for efficient tracking systems in surveillance applications. Many of the proposed techniques are designed for static cameras environments. When the camera is moving, tracking moving objects become more difficult and many techniques fail to detect and track the desired targets. The problem becomes more complex when we want to track a specific object in real-time using a moving Pan and Tilt camera system to keep the target within the image. This type of tracking is of high importance in surveillance applications. When a target is detected at a certain zone, the possibility of automatically tracking it continuously and keeping it within the image until action is taken is very important for security personnel working in very sensitive sites. This work presents a real-time tracking system permitting the detection and continuous tracking of targets using a Pan and Tilt camera platform. A novel and efficient approach for dealing with occlusions is presented. Also a new intelligent forget factor is introduced in order to take into account target shape variations and avoid learning non desired objects. Tests conducted in outdoor operational scenarios show the efficiency and robustness of the proposed approach.
Abstract: Multimedia courseware has been accepted as a tool
that can support teaching and learning process. 'Li2D' courseware
was developed to assist student-s visualization on the topic of Loci in
Two Dimension. This paper describes an evaluation on the
effectiveness and usability of a 'Li2D' courseware. The quasi
experiment was used for the effectiveness evaluation. Usability
evaluation was accomplished based on four constructs of usability,
namely: efficiency, learnability, screen design and satisfaction. An
evaluation on the multimedia elements was also conducted. A total of
63 students of Form Two are involved in the study. The students are
divided into two groups: control and experimental. The experimental
group had to interact with 'Li2D' courseware as part of the learning
activities while the control group used the conventional learning
methods. The results indicate that the experimental group performed
better than the control group in understanding the Loci in Two
Dimensions topic. In terms of usability, the results showed that the
students agreed on the usability in multimedia elements in the 'Li2D'
courseware.
Abstract: ERP systems are the largest software applications adopted by universities, along with quite significant investments in their implementation. However, unlike other applications little research has been conducted regarding these systems in a university environment. This paper aims at providing a critical review of previous research in ERP system in higher education with a special focus on higher education in Australia. The research not only forms the basis of an evaluation of previous research and research needs, it also makes inroads in identifying the payoff of ERPs in the sector from different perspectives with particular reference to the user. The paper is divided into two parts, the first part focuses on ERP literature in higher education at large, while the second focuses on ERP literature in higher education in Australia.