Abstract: Swedish truck industry is investigating the possibility
for implementing the use of Compacted Graphite Iron (CGI) in their
heavy duty diesel engines. Compared to the alloyed gray iron used
today, CGI has superior mechanical properties but not as good
machinability. Another issue that needs to be addressed when
implementing CGI is the inhomogeneous microstructure when the
cast component has different section thicknesses, as in cylinder
blocks. Thinner sections results in finer pearlite, in the material, with
higher strength. Therefore an investigation on its influence on
machinability was needed. This paper focuses on the effect that
interlamellar distance in pearlite has on CGI machinability and
material physical properties. The effect of pearlite content and
nodularity is also examined. The results showed that interlamellar
distance in pearlite did not have as large effect on the material
physical properties or machinability as pearlite content. The paper
also shows the difficulties of obtaining a homogeneous
microstructure in inhomogeneous workpieces.
Abstract: Investigations of the unimolecular decomposition of
vinyl ethyl ether (VEE), vinyl propyl ether (VPE) and vinyl butyl
ether (VBE) have shown that activation of the molecule of a ether
results in formation of a cyclic construction - the transition state (TS),
which may lead to the displacement of the thermodynamic
equilibrium towards the reaction products. The TS is obtained by
applying energy minimization relative to the ground state of an ether
under the program MM2 when taking into account the hydrogen bond
formation between a hydrogen atom of alkyl residue and the extreme
atom of carbon of the vinyl group. The dissociation of TS up to the
products is studied by energy minimization procedure using the
mathematical program Gaussian. The obtained calculation data for
VEE testify that the decomposition of this ether may be conditioned
by hydrogen bond formation for two possible versions: when α- or β-
hydrogen atoms of the ethyl group are bound to carbon atom of the
vinyl group. Applying the same calculation methods to other ethers
(VPE and VBE) it is shown that only in the case of hydrogen bonding
between α-hydrogen atom of the alkyl residue and the extreme atom
of carbon of the vinyl group (αH---C) results in decay of theses
ethers.
Abstract: This paper presents a robust vehicle detection approach using Haar-like feature. It is possible to get a strong edge feature from this Haar-like feature. Therefore it is very effective to remove the shadow of a vehicle on the road. And we can detect the boundary of vehicles accurately. In the paper, the vehicle detection algorithm can be divided into two main steps. One is hypothesis generation, and the other is hypothesis verification. In the first step, it determines vehicle candidates using features such as a shadow, intensity, and vertical edge. And in the second step, it determines whether the candidate is a vehicle or not by using the symmetry of vehicle edge features. In this research, we can get the detection rate over 15 frames per second on our embedded system.
Abstract: This paper proposes a novel spectrum sensing technique
for the digital video broadcasting-terrestrial (DVB-T) systems, which
utilizes the periodicity of pilot signals in the orthogonal frequency
division multiplexing (OFDM) symbols. The proposed scheme can
overcome the effect of the timing synchronization error by recorrelating
the correlation values in the same sample distances. The
numerical results demonstrate that the detection probability performance
of the proposed scheme outperforms that of the conventional
scheme when there exists a timing synchronization error.
Abstract: Indium-tin oxide films are deposited by low plasma
temperature RF sputtering on highly flexible modification of glycol
polyethyleneterephtalate substrates. The produced layers are
characterized with transparency over 82 % and sheet resistance of
86.9 Ω/square. The film’s conductivity was further improved by
additional UV illumination from light source (365 nm), having power
of 250 W. The influence of the UV exposure dose on the structural
and electro-optical properties of ITO was investigated. It was
established that the optimum time of illumination is 10 minutes and
further UV treatment leads to polymer substrates degradation.
Structural and bonds type analysis show that at longer treatment
carbon atoms release and diffuse into ITO films, which worsen their
electrical behavior. For the optimum UV dose the minimum sheet
resistance was measured to be 19.2 Ω/square, and the maximum
transparency remained almost unchanged – above 82 %.
Abstract: The pulp and paper mill effluent is one of the high
polluting effluent amongst the effluents obtained from polluting
industries. All the available methods for treatment of pulp and paper
mill effluent have certain drawbacks. The coagulation is one of the
cheapest process for treatment of various organic effluents. Thus, the
removal of chemical oxygen demand (COD) and colour of paper mill
effluent is studied using coagulation process. The batch coagulation
process was performed using various coagulants like: aluminium
chloride, poly aluminium chloride and copper sulphate. The initial
pH of the effluent (Coagulation pH) has tremendous effect on COD
and colour removal. Poly aluminium chloride (PAC) as coagulant
reduced COD to 84 % and 92 % of colour was removed at an
optimum pH 5 and coagulant dose of 8 ml l-1. With aluminium
chloride at an optimum pH = 4 and coagulant dose of 5 g l-1, 74 %
COD and 86 % colour removal were observed. The results using
copper sulphate as coagulant (a less commercial coagulant) were
encouraging. At an optimum pH 6 and mass loading of 5 g l-1, 76 %
COD reduction and 78 % colour reduction were obtained. It was also
observed that after addition of coagulant, the pH of the effluent
decreases. The decrease in pH was highest for AlCl3, which was
followed by PAC and CuSO4. Significant amount of COD reductions
was obtained by coagulation process. Since the coagulation process
is the first stage for treatment of effluent and some of the coagulant
cations usually remain in the treated effluents. Thus, cation like
copper may be one of the good catalyst for second stage of treatment
process like wet oxidation. The copper has been found to be good
oxidation catalyst then iron and aluminum.
Abstract: In this paper, we present an innovative scheme of
blindly extracting message bits from an image distorted by an attack.
Support Vector Machine (SVM) is used to nonlinearly classify the
bits of the embedded message. Traditionally, a hard decoder is used
with the assumption that the underlying modeling of the Discrete
Cosine Transform (DCT) coefficients does not appreciably change.
In case of an attack, the distribution of the image coefficients is
heavily altered. The distribution of the sufficient statistics at the
receiving end corresponding to the antipodal signals overlap and a
simple hard decoder fails to classify them properly. We are
considering message retrieval of antipodal signal as a binary
classification problem. Machine learning techniques like SVM is
used to retrieve the message, when certain specific class of attacks is
most probable. In order to validate SVM based decoding scheme, we
have taken Gaussian noise as a test case. We generate a data set using
125 images and 25 different keys. Polynomial kernel of SVM has
achieved 100 percent accuracy on test data.
Abstract: Studies revealing the positive relationship between
trade and income are often criticized with the argument that
“development should mean more than rising incomes". Taking this
argument as a base and utilizing panel data, Davies and Quinlivan [1]
have demonstrated that increases in trade are positively associated
with future increases in social welfare as measured by the Human
Development Index (HDI). The purpose of this study is twofold:
Firstly, utilizing an income based country classification; it is aimed
to investigate whether the positive association between foreign trade
and HDI is valid within all country groups. Secondly, keeping the
same categorization as a base; it is aimed to reveal whether the
positive link between trade and HDI still exists when the income
components of the index are excluded. Employing a panel data
framework of 106 countries, this study reveals that the positive link
between trade and human development is valid only for high and
medium income countries. Moreover, the positive link between trade
and human development diminishes in lower-medium income
countries when only non-income components of the index are taken
into consideration.
Abstract: High voltage generators are being subject to higher
voltage rating and are being designed to operate in harsh conditions.
Stator windings are the main component of generators in which
Electrical, magnetical and thermal stresses remain major failures for
insulation degradation accelerated aging. A large number of
generators failed due to stator winding problems, mainly insulation
deterioration. Insulation degradation assessment plays vital role in the
asset life management. Mostly the stator failure is catastrophic
causing significant damage to the plant. Other than generation loss,
stator failure involves heavy repair or replacement cost. Electro
thermal analysis is the main characteristic for improvement design of
stator slot-s insulation. Dielectric parameters such as insulation
thickness, spacing, material types, geometry of winding and slot are
major design consideration. A very powerful method available to
analyze electro thermal performance is Finite Element Method
(FEM) which is used in this paper. The analysis of various stator coil
and slot configurations are used to design the better dielectric system
to reduce electrical and thermal stresses in order to increase the
power of generator in the same volume of core. This paper describes
the process used to perform classical design and improvement
analysis of stator slot-s insulation.
Abstract: This research proposed a new design of helmet-shaped
array transcranial magnetic stimulation coil system. It was constructed
using several sagittal directional wires and several coronal directional
wires. By varying the current direction and strength on each wire, this
array coil system could be constructed into the circular coil and
figure-eight coil of different size. Also, this proposed coil system can
flexibly not only change the stimulation location, range, type and
strength, but also change the shape and the channel number of coil
dynamically.
Abstract: Image compression is one of the most important
applications Digital Image Processing. Advanced medical imaging
requires storage of large quantities of digitized clinical data. Due to
the constrained bandwidth and storage capacity, however, a medical
image must be compressed before transmission and storage. There
are two types of compression methods, lossless and lossy. In Lossless
compression method the original image is retrieved without any
distortion. In lossy compression method, the reconstructed images
contain some distortion. Direct Cosine Transform (DCT) and Fractal
Image Compression (FIC) are types of lossy compression methods.
This work shows that lossy compression methods can be chosen for
medical image compression without significant degradation of the
image quality. In this work DCT and Fractal Compression using
Partitioned Iterated Function Systems (PIFS) are applied on different
modalities of images like CT Scan, Ultrasound, Angiogram, X-ray
and mammogram. Approximately 20 images are considered in each
modality and the average values of compression ratio and Peak
Signal to Noise Ratio (PSNR) are computed and studied. The quality
of the reconstructed image is arrived by the PSNR values. Based on
the results it can be concluded that the DCT has higher PSNR values
and FIC has higher compression ratio. Hence in medical image
compression, DCT can be used wherever picture quality is preferred
and FIC is used wherever compression of images for storage and
transmission is the priority, without loosing picture quality
diagnostically.
Abstract: In this study, it is investigated the stability boundary of
Functionally Graded (FG) panel under the heats and supersonic
airflows. Material properties are assumed to be temperature
dependent, and a simple power law distribution is taken. First-order
shear deformation theory (FSDT) of plate is applied to model the
panel, and the von-Karman strain- displacement relations are
adopted to consider the geometric nonlinearity due to large
deformation. Further, the first-order piston theory is used to model the
supersonic aerodynamic load acting on a panel and Rayleigh damping
coefficient is used to present the structural damping. In order to find a
critical value of the speed, linear flutter analysis of FG panels is
performed. Numerical results are compared with the previous works,
and present results for the temperature dependent material are
discussed in detail for stability boundary of the panel with various
volume fractions, and aerodynamic pressures.
Abstract: In this paper, a class of impulsive BAM fuzzy cellular neural networks with distributed delays and reaction-diffusion terms is formulated and investigated. By employing the delay differential inequality and inequality technique developed by Xu et al., some sufficient conditions ensuring the existence, uniqueness and global exponential stability of equilibrium point for impulsive BAM fuzzy cellular neural networks with distributed delays and reaction-diffusion terms are obtained. In particular, the estimate of the exponential convergence rate is also provided, which depends on system parameters, diffusion effect and impulsive disturbed intention. It is believed that these results are significant and useful for the design and applications of BAM fuzzy cellular neural networks. An example is given to show the effectiveness of the results obtained here.
Abstract: Implementation of response surface methodology (RSM) was employed to study the effects of two factor (rubber clearance and round per minute) in brown rice peeling machine of The optimal BROKENS yield (19.02, average of three repeats),.The optimized composition derived from RSM regression was analyzed using Regression analysis and Analysis of Variance (ANOVA). At a significant level α = 0.05, the values of Regression coefficient, R 2 (adj)were 97.35 % and standard deviation were 1.09513. The independent variables are initial rubber clearance, and round per minute parameters namely. The investigating responses are final rubber clearance, and round per minute (RPM). The restriction of the optimization is the designated.
Abstract: The research was set up on chernozem soil at the Látókép AGTC MÉK research area of the University of Debrecen in Hungary. We examined the yield, the yield production per 1kg NPK fertilizer and the water and nutrient utilization of hybrid PR37N01 and PR37M81 in 2013. We found that PR37N01 produced the most yield at the level of N120+P (17,476kg ha-1) while PR37M81 reached the highest yield at level N150+PK (16,754kg ha-1). Studies related to yield production per 1kg NPK indicated that the best results were achieved at level N30+PK compared to the control treatment. Yield production per 1kg NPK was17.6kg kg-1 by P37N01 and 44.2kg kg-1 by PR37M81. By comparing the water utilization of hybrids we found that the worst water utilization results were reached in the control treatment (PR37N01: 26.2kg mm-1, PR37M81: 19.5kg mm-1). The best water utilization values were produced at level N120+PK in the case of hybrid PR37N01 (32.1kg mm-1) and at N150+PK in the case of hybrid PR37M81 (30.8kg mm-1). We established the values of the nutrient reaction and the fertilizer optimum of hybrids. We discovered a strong relationship between the amount of fertilizer applied and the yield produced (r2= 0.8228–0.9515). The best nutrient response was induced by hybrid PR37N01, while the weakest results were reached by hybrid PR37M81.
Abstract: In this era of technology, fueled by the pervasive usage of the internet, security is a prime concern. The number of new attacks by the so-called “bots", which are automated programs, is increasing at an alarming rate. They are most likely to attack online registration systems. Technology, called “CAPTCHA" (Completely Automated Public Turing test to tell Computers and Humans Apart) do exist, which can differentiate between automated programs and humans and prevent replay attacks. Traditionally CAPTCHA-s have been implemented with the challenge involved in recognizing textual images and reproducing the same. We propose an approach where the visual challenge has to be read out from which randomly selected keywords are used to verify the correctness of spoken text and in turn detect the presence of human. This is supplemented with a speaker recognition system which can identify the speaker also. Thus, this framework fulfills both the objectives – it can determine whether the user is a human or not and if it is a human, it can verify its identity.
Abstract: Numerical studies have been carried out using a two
dimensional code to examine the influence of pressure / thrust
transient of solid propellant rockets at liftoff. This code solves
unsteady Reynolds-averaged thin-layer Navier–Stokes equations by
an implicit LU-factorization time-integration method. The results
from the parametric study indicate that when the port is narrow there
is a possibility of increase in pressure / thrust-rise rate due to
relatively high flame spread rate. Parametric studies further reveal
that flame spread rate can be altered by altering the propellant
properties, igniter jet characteristics and nozzle closure burst pressure
without altering the grain configuration and/or the mission
demanding thrust transient. We observed that when the igniter
turbulent intensity is relatively low the vehicle could liftoff early due
to the early flow choking of the rocket nozzle. We concluded that the
high pressurization-rate has structural implications at liftoff in
addition to transient burning effect. Therefore prudent selection of the
port geometry and the igniter, for meeting the mission requirements,
within the given envelop are meaningful objectives for any designer
for the smooth liftoff of solid propellant rockets.
Abstract: Economic freedoms, most emphasized issue in the recent years, are considered to affect economic growth and performance via institutional structure. In this context, a model that includes Turkey and Middle East Countries, and where the effects of economic freedom on growth are examined, was formed. For the groups of countries determined, in the study carried out by using the dataset belonging the period of 2004 - 2009, between economic freedoms and growth, a negative relationship was observed as group. In the sense of individual effects, it was identified that there was a positive relationship in terms of some Middle East Countries and Turkey.
Abstract: The aim of this study was to establish the relationship between the principles of Educational Sport and the objectives of Physical Education in two brasilian laws: National Curriculum Guidelines (PCNs) for the Elementary and Middle School Levels and the Guidelines and Basis Legislation (LDB). The method used was the survey analysis in order to determine the practices present in, or the opinions of, a specific population. The instrument used in this research was a questionnaire. After a broad review of the bibliography and according to the methodological procedures, the aim was to set the relationships between the Principles of Educational Sport and the objectives of Physical Education, according to the Brazilian Law (LDB) and National Curriculum Guidelines (PCNs) in a table made under the analysis of a group of specialists. As the relation between the principles of Educational Sport and the objectives of School Physical Education have shown, we can state that School Physical Education has gained pedagogical security for the potential use of Educational Sport as part of its contents.
Abstract: Multiple criteria decision making (MCDM) is an approach to ranking the solutions and finding the best one when two or more solutions are provided. In this study, MCDM approach is proposed to select the most suitable scheduling rule of robotic flexible assembly cells (RFACs). Two MCDM approaches, Analytic Hierarchy Process (AHP) and Technique for Order Preference by Similarity to Ideal Solution (TOPSIS) are proposed for solving the scheduling rule selection problem. The AHP method is employed to determine the weights of the evaluation criteria, while the TOPSIS method is employed to obtain final ranking order of scheduling rules. Four criteria are used to evaluate the scheduling rules. Also, four scheduling policies of RFAC are examined to choose the most appropriate one for this purpose. A numerical example illustrates applications of the suggested methodology. The results show that the methodology is practical and works in RFAC settings.