Abstract: While in practice negotiation is always a mix of
cooperation and competition, these two elements correspond to
different approaches of the relationship and also different orientations
in term of strategy, techniques, tactics and arguments employed by
the negotiators with related effects and in the end leading to different
outcomes. The levels of honesty, trust and therefore cooperation are
influenced not only by the uncertainty of the situation, the objectives,
stakes or power but also by the orientation given from the very
beginning of the relationship. When negotiation is reduced to a
confrontation of power, participants rely on coercive measures, using
different kinds of threats or make false promises and bluff in order to
establish a more acceptable balance of power.
Most of the negotiators have a tendency to complain about the
unethical aspects of the tactics used by their counterparts while, as
the same time, they are mostly unaware of the sources of influence of
their own vision and practices. In this article, our intention is to
clarify these sources and try to understand what can lead negotiators
to unethical practices.
Abstract: The effectiveness of consuming a nutrient fortified oat drink on iron, zinc, vitamin A and vitamin C status was assessed among a cohort of school-aged Filipino children. Ultimate study implementation permitted only a within-subject comparison of change in nutritional status after four months of consuming a nutrient fortified oat drink. Thirty-eight anemic children (5-8 years) consumed an oat drink fortified with iron as NaFeEDTA, zinc, vitamin A and vitamin C for 120 days. Height, weight, serum nutrient levels, anemia status and dietary intake were assessed pre and post intervention. Thirty-four anemic children completed the intervention. After 4 months of intervention, prevalence of anemia decreased by 68% and significant improvements in iron and vitamin A status were observed. Results demonstrate the effectiveness of the fortified oat drink in alleviating anemia in young children and highlight the value of fortification programs
Abstract: Analytical investigation of the sedimentation
processes in the river engineering and hydraulic structures is of vital
importance as this can affect water supply for the cultivating lands in
the command area. The reason being that gradual sediment formation
behind the reservoir can reduce the nominal capacity of these dams.
The aim of the present paper is to analytically investigate
sedimentation process along the river course and behind the storage
reservoirs in general and the Eastern Intake of the Dez Diversion weir
in particular using the SHARC software. Results of the model
indicated the water level at 115.97m whereas the real time
measurement from the river cross section was 115.98 m which
suggests a significantly close relation between them. The average
transported sediment load in the river was measured at 0.25mm ,
from which it can be concluded that nearly 100% of the suspended
loads in river are moving which suggests no sediment settling but
indicates that almost all sediment loads enters into the intake. It was
further showed the average sediment diameter entering the intake to
be 0.293 mm which in turn suggests that about 85% of suspended
sediments in the river entre the intake. Comparison of the results
from the SHARC model with those obtained form the SSIIM
software suggests quite similar outputs but distinguishing the
SHARC model as more appropriate for the analysis of simpler
problems than other model.
Abstract: Generation system reliability assessment is an
important task which can be performed using deterministic or
probabilistic techniques. The probabilistic approaches have
significant advantages over the deterministic methods. However,
more complicated modeling is required by the probabilistic
approaches. Power generation model is a basic requirement for this
assessment. One form of the generation models is the well known
capacity outage probability table (COPT). Different analytical
techniques have been used to construct the COPT. These approaches
require considerable mathematical modeling of the generating units.
The unit-s models are combined to build the COPT which will add
more burdens on the process of creating the COPT. Decimal to
Binary Conversion (DBC) technique is widely and commonly applied
in electronic systems and computing This paper proposes a novel
utilization of the DBC to create the COPT without engaging in
analytical modeling or time consuming simulations. The simple
binary representation , “0 " and “1 " is used to model the states o f
generating units. The proposed technique is proven to be an effective
approach to build the generation model.
Abstract: An exploratory computational investigation using
RANS & URANS was carried out to understand the aerodynamics
around an isolatedsingle rotating wheel with decreasing ground
proximity. The wheel was initially modeled in free air conditions,
then with decreasing ground proximity and increased yaw angle with
rotational speeds. Three speeds of rotation were applied to the wheel
so that the effect of different angular velocities can be investigated. In
addition to rotation, three different yaw angles were applied to the
rotating wheel in order to understand how these two variables
combined affect the aerodynamic flow field around the wheel.
Abstract: Post-anthesis drought stress is the most important
problem affecting wheat production in dryland fields, specially in
Mediterranean regions. The main objective of this research was to
evaluate drought tolerance indices in dryland wheat genotypes under
post-anthesis drought stress. The research was including two different
experiments. In each experiment, twenty dryland bread wheat
genotypes were sown in a randomized complete blocks design
(RCBD) with three replications. One of experiments belonged to
rain-fed conditions (post-anthesis drought stress) and other
experiment was under non-stress conditions (with supplemental
irrigation). Different drought tolerance indices include Stress
Tolerance (Tol), Mean Productivity (MP), Geometric Mean
Productivity (GMP), Stress Susceptibility Index (SSI), Stress
Tolerance Index (STI), Harmonic Mean (HAM), Yield Index (YI)
and Yield Stability Index (YSI) were evaluate based on grain yield
under rain-fed (Ys) and supplemental irrigation (Yp) environments.
G10 and G12 were the most tolerant genotypes based on TOL and
SSI. But, based on MP, GMP, STI, HAM and YI indices, G1 and G2
were selected. STI, GMP and MP indices had high correlation with
grain yield under rain-fed and supplementary irrigation conditions
and were recognized as appropriate indices to identify genotypes with
high grain yield and low sensitivity to drought stress environments.
Abstract: Raw wood vinegar was purified by both standing and
filtering methods. Toxicity tests were conducted under laboratory
conditions by the topical application method (contact poison) and
feeding method (stomach poison). Larvicidal activities of wood
vinegar at four different concentrations (10, 15, 20, 25 and 30 %)
were studied against second instar larvae of housefly (Musca
domestica L.). Four replicates were maintained for all treatments and
controls. Larval mortality was recorded up to 96 hours and compared
with the larval survivability by two methods of larvicidal bioassay.
Percent pupation and percent adult emergence were observed in
treated M. domestica. The study revealed that the feeding method
gave higher efficiency compared with the topical application method.
Larval mortality increased with increasing concentration of wood
vinegar and the duration of exposure. No mortality was found in
treated M. domestica larvae at minimum 10% concentration of wood
vinegar through the experiments. The treated larvae were maintained
up to pupa and adult emergence. At 30% maximum concentration
larval duration was extended to 11 days in M. domestica for topical
application method and 9 days for feeding method. Similarly the
pupal durations were also increased with increased concentrations
(16 and 24 days for topical application method and feeding method
respectively at 30% concentration) of the treatments.
Abstract: Thrombosis can be life threatening, necessitating therefore its instant treatment. Hydergine, a nootropic agent is used as a cognition enhancer in stroke patients but relatively little is known about its anti-thrombolytic effect. To investigate this aspect, in vivo and ex vivo experiments were designed and conducted. Three groups of rats were injected 1.5mg, 3.0mg and 4.5mg hydergine intraperitonealy with and without prior exposure to fresh plasma. Positive and negative controls were run in parallel. Animals were sacrificed after 1.5hrs and BT, CT, PT, INR, APTT, plasma calcium levels were estimated. For ex vivo analyses, each 1ml blood aspirated was exposed to 0.1mg, 0.2mg, 0.3mg dose of hydergine with parallel controls. Parameters analyzed were as above. Statistical analysis was through one-way ANOVA. Dunken-s and Tukey-s tests provided intra-group variance. BT, CT, PT, INR and APTT increased while calcium levels dropped significantly (P
Abstract: This work presents a numerical model developed to
simulate the dynamics and vibrations of a multistage tractor gearbox.
The effect of time varying mesh stiffness, time varying frictional
torque on the gear teeth, lateral and torsional flexibility of the shafts
and flexibility of the bearings were included in the model. The model
was developed by using the Lagrangian method, and it was applied to
study the effect of three design variables on the vibration and stress
levels on the gears. The first design variable, module, had little effect
on the vibration levels but a higher module resulted to higher bending
stress levels. The second design variable, pressure angle, had little
effect on the vibration levels, but had a strong effect on the stress
levels on the pinion of a high reduction ratio gear pair. A pressure
angle of 25o resulted to lower stress levels for a pinion with 14 teeth
than a pressure angle of 20o. The third design variable, contact ratio,
had a very strong effect on both the vibration levels and bending
stress levels. Increasing the contact ratio to 2.0 reduced both the
vibration levels and bending stress levels significantly. For the gear
train design used in this study, a module of 2.5 and contact ratio of
2.0 for the various meshes was found to yield the best combination
of low vibration levels and low bending stresses. The model can
therefore be used as a tool for obtaining the optimum gear design
parameters for a given multistage spur gear train.
Abstract: Optimal routing in communication networks is a
major issue to be solved. In this paper, the application of Tabu Search
(TS) in the optimum routing problem where the aim is to minimize
the computational time and improvement of quality of the solution in
the communication have been addressed. The goal is to minimize the
average delays in the communication. The effectiveness of Tabu
Search method is shown by the results of simulation to solve the
shortest path problem. Through this approach computational cost can
be reduced.
Abstract: This paper presents the climatic range calculations for
comfort evaporative cooling for Tehran. In this study the minimum
climatic conditions required to achieve an appropriate comfort zone
will be presented.
Physiologically uncomfortable conditions in arid climates are
mainly caused by the extreme heat and dryness. Direct evaporative
cooling adds moisture to the air stream until the air stream is close to
saturation. The dry bulb temperature is reduced, while the wet bulb
temperature stays the same. Evaporative cooling is economical,
effective, environmentally friendly, and healthy.
Comfort cooling by direct evaporative cooling (passive or fan
forced) in the 35. 41 N (such as Tehran) latitude requires design
wet-bulb temperature not over 25.4 C. Evaporative cooling outside
this limit cannot achieve the required 26.7 ET, and is recommended
for relief cooling only.
Abstract: In this paper, we propose a solution to the motion
control problem of a 2-link revolute manipulator arm. We require the
end-effector of the arm to move safely to its designated target in a
priori known workspace cluttered with fixed circular obstacles of
arbitrary position and sizes. Firstly a unique velocity algorithm is
used to move the end-effector to its target. Secondly, for obstacle
avoidance a turning angle is designed, which when incorporated into
the control laws ensures that the entire robot arm avoids any number
of fixed obstacles along its path enroute the target. The control laws
proposed in this paper also ensure that the equilibrium point of the
system is asymptotically stable. Computer simulations of the
proposed technique are presented.
Abstract: In this paper, genetic algorithm (GA) opmization technique is applied to design Flexible AC Transmission System (FACTS)-based damping controllers. Two types of controller structures, namely a proportional-integral (PI) and a lead-lag (LL) are considered. The design problem of the proposed controllers is formulated as an optimization problem and GA is employed to search for optimal controller parameters. By minimizing the time-domain based objective function, in which the deviation in the oscillatory rotor speed of the generator is involved; stability performance of the system is improved. The proposed controllers are tested on a weakly connected power system subjected to different disturbances. The non-linear simulation results are presented to show the effectiveness of the proposed controller and their ability to provide efficient damping of low frequency oscillations. It is also observed that the proposed SSSC-based controllers improve greatly the voltage profile of the system under severe disturbances. Further, the dynamic performances of both the PI and LL structured FACTS-controller are analyzed at different loading conditions and under various disturbance condition as well as under unbalanced fault conditions..
Abstract: This paper presents the impact study of apparent
reactance injected by series Flexible AC Transmission System
(FACTS) i.e. Thyristor Controlled Series Reactor (TCSR) on the
measured impedance of a 400 kV single electrical transmission line
in the presence of phase to earth fault with fault resistance. The study
deals with an electrical transmission line of Eastern Algerian
transmission networks at Group Sonelgaz (Algerian Company of
Electrical and Gas) compensated by TCSR connected at midpoint of
the line. This compensator used to inject active and reactive powers
is controlled by three TCSR-s. The simulations results investigate the
impacts of the TCSR on the parameters of short circuit calculation
and parameters of measured impedance by distance relay in the
presence of earth fault for three cases study.
Abstract: Incremental forming is a complex forming process with
continuously local cumulative deformation taking place during its
process, and springback that forming quality affected by would occur.
The springback evaluation method based on forming error
compensation also was proposed, which it can be defined as the
difference between theory and the actual amount of compensation
along the measured direction. According to forming error
compensation evaluation method, experiments was designed and
implemented. And from the results that obtained it can be show, the
magnitude of springback average (δE) of formed parts was very small,
and the forming precision could be significantly improved by adopting
compensation method. Based on double tensile stress state in the main
deformation area, a hypothesis that there is little springback be arisen
by bending behavior on the formed parts that was proposed.
Abstract: The leisure boatbuilding industry has tight profit margins that demand that boats are created to a high quality but with low cost. This requirement means reduced design times combined with increased use of design for production can lead to large benefits. The evolutionary nature of the boatbuilding industry can lead to a large usage of previous vessels in new designs. With the increase in automated tools for concurrent engineering within structural design it is important that these tools can reuse this information while subsequently feeding this to designers. The ability to accurately gather this materials and parts data is also a key component to these tools. This paper therefore aims to develop an architecture made up of neural networks and databases to feed information effectively to the designers based on previous design experience.
Abstract: To achieve reliable solutions, today-s numerical and
experimental activities need developing more accurate methods and
utilizing expensive facilities, respectfully in microchannels. The analytical
study can be considered as an alternative approach to alleviate
the preceding difficulties. Among the analytical solutions, those with
high robustness and low complexities are certainly more attractive.
The perturbation theory has been used by many researchers to analyze
microflows. In present work, a compressible microflow with constant
heat flux boundary condition is analyzed. The flow is assumed to be
fully developed and steady. The Mach and Reynolds numbers are also
assumed to be very small. For this case, the creeping phenomenon
may have some effect on the velocity profile. To achieve robustness
solution it is assumed that the flow is quasi-isothermal. In this study,
the creeping term which appears in the slip boundary condition
is formulated by different mathematical formulas. The difference
between this work and the previous ones is that the creeping term
is taken into account and presented in non-dimensionalized form.
The results obtained from perturbation theory are presented based
on four non-dimensionalized parameters including the Reynolds,
Mach, Prandtl and Brinkman numbers. The axial velocity, normal
velocity and pressure profiles are obtained. Solutions for velocities
and pressure for two cases with different Br numbers are compared
with each other and the results show that the effect of creeping
phenomenon on the velocity profile becomes more important when
Br number is less than O(ε).
Abstract: In this study, single nozzle method used for
electrospinning technique which composite polymer solution with
cellulose nanowiskers (CNW) was treated by ultrasonic sonificator
have been compared with coaxial (double) nozzle method, in terms of
mechanical, thermal and morphological properties of composite
nanofiber. The effect of water content in composite polymer solution
on properties of nanofiber has also been examined. It has been seen
that single nozzle method which polymer solution does not contain
water has better results than that of coaxial method, in terms of
mechanical, thermal and morphological properties of nanofiber.
However, it is necessary to make an optimization study on setting
condition of ultrasonic treatment to get better dispersion of CNW in
composite nanofiber and to get better mechanical and thermal
properties
Abstract: This study attempts to investigate the relationship
between internal CSR practices and organizational commitment
based on the social exchange theory (SET). Specifically, we examine
the impact of five dimensions of internal CSR practices on
organizational commitment: health and safety, human rights, training
and education, work life balance and workplace diversity. The
proposed model was tested on a sample of 336 frontline employees
within the banking sector in Jordan. Results showed that all internal
CSR dimensions are significantly and positively related to affective
and normative commitment. In addition, the findings of this study
indicate that all internal CSR dimensions did not have a significant
relationship with continuance commitment. Limitations of the study,
directions for future research, and implications of the findings are
discussed.
Abstract: The contribution is dealing with the influence of high speed parameters on the quality of machined surface. In general the principle of high speed cutting lies in achieving faster machine times with concurrent increase in accuracy and quality of the machined areas in largely irregular, mathematically hard to define shapes. High speed machining is a highly effective method of machining with the following goals: increasing of machining productivity, increasing of quality of the machined surface, improving of machining economy, improving of ecological aspects of machining. This article is based on an experiment performed by the Department of Machining and Assembly of the Faculty of Mechanical Engineering of VŠBTechnical University of Ostrava.