Abstract: Load managing method on road became necessary
since overloaded vehicles occur damage on road facilities and existing
systems for preventing this damage still show many
problems.Accordingly, efficient managing system for preventing
overloaded vehicles could be organized by using the road itself as a
scale by applying genetic algorithm to analyze the load and the drive
information of vehicles.Therefore, this paper organized Ubiquitous
sensor network system for development of intelligent overload vehicle
regulation system, also in this study, to use the behavior of road, the
transformation was measured by installing underground box type
indoor model and indoor experiment was held using genetic algorithm.
And we examined wireless possibility of overloaded vehicle
regulation system through experiment of the transmission and
reception distance.If this system will apply to road and bridge, might
be effective for economy and convenience through establishment of
U-IT system..
Abstract: This study discusses the effect of uncertainty on
production levels of a petrochemical complex. Uncertainly or
variations in some model parameters, such as prices, supply and
demand of materials, can affect the optimality or the efficiency of any
chemical process. For any petrochemical complex with many plants,
there are many sources of uncertainty and frequent variations which
require more attention. Many optimization approaches are proposed
in the literature to incorporate uncertainty within the model in order
to obtain a robust solution. In this work, a stability analysis approach
is applied to a deterministic LP model of a petrochemical complex
consists of ten plants to investigate the effect of such variations on
the obtained optimal production levels. The proposed approach can
determinate the allowable variation ranges of some parameters,
mainly objective or RHS coefficients, before the system lose its
optimality. Parameters with relatively narrow range of variations, i.e.
stability limits, are classified as sensitive parameters or constraints
that need accurate estimate or intensive monitoring. These stability
limits offer easy-to-use information to the decision maker and help in
understanding the interaction between some model parameters and
deciding when the system need to be re-optimize. The study shows
that maximum production of ethylene and the prices of intermediate
products are the most sensitive factors that affect the stability of the
optimum solution
Abstract: The effect of streamwise conduction on the thermal
characteristics of forced convection for nanofluidic flow in
rectangular microchannel heat sinks under isothermal wall has been
investigated. By applying the fin approach, models with and without
streamwise conduction term in the energy equation were developed
for hydrodynamically and thermally fully-developed flow. These two
models were solved to obtain closed form analytical solutions for the
nanofluid and solid wall temperature distributions and the analysis
emphasized details of the variations induced by the streamwise
conduction on the nanofluid heat transport characteristics. The effects
of the Peclet number, nanoparticle volume fraction, thermal
conductivity ratio on the thermal characteristics of forced convection
in microchannel heat sinks are analyzed. Due to the anomalous
increase in the effective thermal conductivity of nanofluid compared
to its base fluid, the effect of streamwise conduction is expected to be
more significant. This study reveals the significance of the effect of
streamwise conduction under certain conditions of which the
streamwise conduction should not be neglected in the forced
convective heat transfer analysis of microchannel heat sinks.
Abstract: Recurrence of aneurysm rupture can be attributed to
coil migration and compaction. In order to verify the effects of
hemodynamics on coil compaction and migration, we analyze the
forces and displacements on the coil bundle using a computational
method. Lateral aneurysms partially filled coils are modeled, and
blood flow fields and coil deformations are simulated considering
fluid and solid interaction. Effects of aneurysm neck size and parent
vessel geometry are also investigated. The results showed that coil
deformation was larger in the aneurysms with a wider neck. Parent
vessel geometry and aneurysm neck size also affected mean pressure
force profiles on the coil surface. Pressure forces were higher in wide
neck models with curved parent vessel geometry. Simulation results
showed that coils in the wide neck aneurysm with a curved parent
vessel may be displaced and compacted more easily.
Abstract: The purpose of this research study is to investigate the manner in which various loads affect the mechanical properties of the formed mild steel plates. The investigation focuses on examining the cross-sectional area of the metal plate at the centre of the formed mild steel plate. Six mild steel plates were deformed with different loads. The loads applied on the plates had a magnitude of 5 kg, 10 kg, 15 kg, 20 kg, 25 kg and 30 kg. The radius of the punching die was 120 mm and the loads were applied at room temperature. The investigations established that the applied load causes the Vickers microhardness at the cross-sectional area of the plate to increase due to strain hardening. Hence, the percentage increase of the hardness due to the load was found to be directly proportional to the increase in the load. Furthermore, the tensile test results for the parent material showed that the average Ultimate Tensile Strength (UTS) for the three samples was 308 MPa while the average Yield Strength and Percentage Elongation were 227 MPa and 38 % respectively. Similarly, the UTS of the formed components increased after the deformation of the plate, as such it can be concluded that the forming loads alter the mechanical properties of the materials by improving and strengthening the material properties.
Abstract: The objective of the present research manuscript is to
perform parametric, nonparametric, and decision tree analysis to
evaluate two treatments that are being used for breast cancer patients.
Our study is based on utilizing real data which was initially used in
“Tamoxifen with or without breast irradiation in women of 50 years
of age or older with early breast cancer" [1], and the data is supplied
to us by N.A. Ibrahim “Decision tree for competing risks survival
probability in breast cancer study" [2]. We agree upon certain aspects
of our findings with the published results. However, in this
manuscript, we focus on relapse time of breast cancer patients instead
of survival time and parametric analysis instead of semi-parametric
decision tree analysis is applied to provide more precise
recommendations of effectiveness of the two treatments with respect
to reoccurrence of breast cancer.
Abstract: The effects of global warming on India vary from the
submergence of low-lying islands and coastal lands to the melting of
glaciers in the Indian Himalayas, threatening the volumetric flow rate
of many of the most important rivers of India and South Asia. In
India, such effects are projected to impact millions of lives. As a
result of ongoing climate change, the climate of India has become
increasingly volatile over the past several decades; this trend is
expected to continue.
Climate change is one of the most important global environmental
challenges, with implications for food production, water supply,
health, energy, etc. Addressing climate change requires a good
scientific understanding as well as coordinated action at national and
global level. The climate change issue is part of the larger challenge
of sustainable development. As a result, climate policies can be more
effective when consistently embedded within broader strategies
designed to make national and regional development paths more
sustainable. The impact of climate variability and change, climate
policy responses, and associated socio-economic development will
affect the ability of countries to achieve sustainable development
goals.
A very well calibrated Soil and Water Assessment Tool (R2 =
0.9968, NSE = 0.91) was exercised over the Khatra sub basin of the
Kangsabati River watershed in Bankura district of West Bengal,
India, in order to evaluate projected parameters for agricultural
activities. Evapotranspiration, Transmission Losses, Potential
Evapotranspiration and Lateral Flow to reach are evaluated from the
years 2041-2050 in order to generate a picture for sustainable
development of the river basin and its inhabitants.
India has a significant stake in scientific advancement as well as
an international understanding to promote mitigation and adaptation.
This requires improved scientific understanding, capacity building,
networking and broad consultation processes. This paper is a
commitment towards the planning, management and development of
the water resources of the Kangsabati River by presenting detailed
future scenarios of the Kangsabati river basin, Khatra sub basin, over
the mentioned time period.
India-s economy and societal infrastructures are finely tuned to the
remarkable stability of the Indian monsoon, with the consequence
that vulnerability to small changes in monsoon rainfall is very high.
In 2002 the monsoon rains failed during July, causing profound loss
of agricultural production with a drop of over 3% in India-s GDP.
Neither the prolonged break in the monsoon nor the seasonal rainfall
deficit was predicted. While the general features of monsoon
variability and change are fairly well-documented, the causal
mechanisms and the role of regional ecosystems in modulating the
changes are still not clear. Current climate models are very poor at
modelling the Asian monsoon: this is a challenging and critical
region where the ocean, atmosphere, land surface and mountains all
interact. The impact of climate change on regional ecosystems is
likewise unknown. The potential for the monsoon to become more
volatile has major implications for India itself and for economies
worldwide. Knowledge of future variability of the monsoon system,
particularly in the context of global climate change, is of great
concern for regional water and food security.
The major findings of this paper were that of all the chosen
projected parameters, transmission losses, soil water content,
potential evapotranspiration, evapotranspiration and lateral flow to
reach, display an increasing trend over the time period of years 2041-
2050.
Abstract: Chitosan is a biopolymer composed of glucosamine
and N-acetyl glucosamine. Solubility and viscosity pose problems in
some applications. These problems can be overcome with unique
modifications. In this study, firstly, chitosan was modified by caffeic
acid and thioglycolic acid, separately. Then, growing effects of these
modified polymers was observed in U937 cell line. Caffeic acid is a
phenolic compound and its modifications act carcinogenic inhibitors
in drugs. Thiolated chitosans are commonly being used for drugdelivery
systems in various routes, because of enhancing
mucoadhesiveness property. U937 cell line was used model cell for
leukaemia. Modifications were achieved by 1 – 15 % binding range.
Increasing binding ratios showed higher radical-scavenging activity
and reducing cell growth, in compared to native chitosan. Caffeic
acid modifications showed higher radical-scavenging activity than
thiolated chitosans at the same concentrations. Caffeic acid and
thioglycolic acid modifications inhibited growth of U937, effectively.
Abstract: The flow and heat transfer characteristics for natural
convection along an inclined plate in a saturated porous medium with
an applied magnetic field have been studied. The fluid viscosity has
been assumed to be an inverse function of temperature. Assuming
temperature vary as a power function of distance. The transformed
ordinary differential equations have solved by numerical integration
using Runge-Kutta method. The velocity and temperature profile
components on the plate are computed and discussed in detail for
various values of the variable viscosity parameter, inclination angle,
magnetic field parameter, and real constant (λ). The results have also
been interpreted with the aid of tables and graphs. The numerical
values of Nusselt number have been calculated for the mentioned
parameters.
Abstract: An experiment of vented gas explosions involving two
different cylinder vessel volumes (0.2 and 0.0065 m3) was reported,
with equivalence ratio (Φ) ranged from 0.3 to 1.6. Both vessels were
closed at the rear end and fitted at the other side with a circular
orifice plate that gives a constant vent coefficient (K =Av/V2/3) of
16.4. It was shown that end ignition gives higher overpressures than
central ignition, even though most of the published work on venting
uses central ignition. For propane and ethylene, it is found that rich
mixtures gave the highest overpressures and these mixtures are not
considered in current vent design guidance; which the guideline is
based on mixtures giving the maximum flame temperature. A strong
influence of the vessel volume at constant K was found for methane,
propane, ethylene and hydrogen-air explosions. It can be concluded
that self- acceleration of the flame, which is dependent on the
distance of a flame from the ignition and the ‘suction’ at the vent
opening are significant factors affecting the vent flow during
explosion development in vented gas explosion. This additional
volume influence on vented explosions is not taken into account in
the current vent design guidance.
Abstract: In this paper methodology to exploit creeping wave
for body area network BAN communication reliability are described.
Creeping wave propagation effects are visualized & analyzed.
During this work Dipole, IA antennas various antennas were
redesigned using existing designs and their propagation
characteristics were verified for optimum performance when used on
BANs. These antennas were then applied on body shapes-including
rectangular, spherical and cylindrical so that all the effects of actual
human body can be taken nearly into account. Parametric simulation
scheme was devised so that on Body channel characterization can be
visualized at front, curved and back region. In the next phase
multiple inputs multiple output MIMO scheme was introduced where
virtual antennas were used in order to diminish the effects of
antennas on the propagation of waves. Results were, extracted and
analyzed at different heights. Finally based on comparative
measurement and analysis it was concluded that on body propagation
can be exploited to gain spatial diversity.
Abstract: The aim of the present investigation was to compare
sex differences in thyroid gland structure of rabbits. Five adult male
and five adult female (3.1-3.5 kg body weight) New Zealand white
rabbits were used in the experiment. Results showed that at light
microscopic level, there was no sex difference in microscopic
appearance of the thyroid glands. At electron microscopic level,
however, the mitochondria and the microvilli of the follicular cells
are more numerous and the Golgi complex is also more extensive in
male rabbits in comparison to females. Results obtained from
micrometric measurements showed that the volume density of the
follicles is higher in males than in females, but the differences are not
statistically significant .The volume density of epithelium and the
height of follicular cells are significantly greater in males than in
females and reverse is true about the volume density of interstitium
(p
Abstract: Circular tubes have been widely used as structural
members in engineering application. Therefore, its collapse behavior
has been studied for many decades, focusing on its energy absorption
characteristics. In order to predict the collapse behavior of members,
one could rely on the use of finite element codes or experiments.
These tools are helpful and high accuracy but costly and require
extensive running time. Therefore, an approximating model of tubes
collapse mechanism is an alternative for early step of design. This
paper is also aimed to develop a closed-form solution of thin-walled
circular tube subjected to bending. It has extended the Elchalakani et
al.-s model (Int. J. Mech. Sci.2002; 44:1117-1143) to include the
rate of energy dissipation of rolling hinge in the circumferential
direction. The 3-D geometrical collapse mechanism was analyzed by
adding the oblique hinge lines along the longitudinal tube within the
length of plastically deforming zone. The model was based on the
principal of energy rate conservation. Therefore, the rates of internal
energy dissipation were calculated for each hinge lines which are
defined in term of velocity field. Inextensional deformation and
perfect plastic material behavior was assumed in the derivation of
deformation energy rate. The analytical result was compared with
experimental result. The experiment was conducted with a number of
tubes having various D/t ratios. Good agreement between analytical
and experiment was achieved.
Abstract: Congestion control is one of the fundamental issues in computer networks. Without proper congestion control mechanisms there is the possibility of inefficient utilization of resources, ultimately leading to network collapse. Hence congestion control is an effort to adapt the performance of a network to changes in the traffic load without adversely affecting users perceived utilities. AIMD (Additive Increase Multiplicative Decrease) is the best algorithm among the set of liner algorithms because it reflects good efficiency as well as good fairness. Our control model is based on the assumption of the original AIMD algorithm; we show that both efficiency and fairness of AIMD can be improved. We call our approach is New AIMD. We present experimental results with TCP that match the expectation of our theoretical analysis.
Abstract: This study investigated climatic factors associated
with influenza cases in Southern Thailand. The main aim for use
regression analysis to investigate possible causual relationship of
climatic factors and variability between the border of the Andaman
Sea and the Gulf of Thailand. Southern Thailand had the highest
Influenza incidences among four regions (i.e. north, northeast, central
and southern Thailand). In this study, there were 14 climatic factors:
mean relative humidity, maximum relative humidity, minimum
relative humidity, rainfall, rainy days, daily maximum rainfall,
pressure, maximum wind speed, mean wind speed, sunshine duration,
mean temperature, maximum temperature, minimum temperature,
and temperature difference (i.e. maximum – minimum temperature).
Multiple stepwise regression technique was used to fit the statistical
model. The results indicated that the mean wind speed and the
minimum relative humidity were positively associated with the
number of influenza cases on the Andaman Sea side. The maximum
wind speed was positively associated with the number of influenza
cases on the Gulf of Thailand side.
Abstract: The product development process (PDP) in the
Technology group plays a very important role in the launch of any
product. While a manufacturing process encourages the use of certain
measures to reduce health, safety and environmental (HSE) risks on
the shop floor, the PDP concentrates on the use of Geometric
Dimensioning and Tolerancing (GD&T) to develop a flawless design.
Furthermore, PDP distributes and coordinates activities between
different departments such as marketing, purchasing, and
manufacturing. However, it is seldom realized that PDP makes a
significant contribution to developing a product that reduces HSE
risks by encouraging the Technology group to use effective GD&T.
The GD&T is a precise communication tool that uses a set of
symbols, rules, and definitions to mathematically define parts to be
manufactured. It is a quality assurance method widely used in the oil
and gas sector. Traditionally it is used to ensure the
interchangeability of a part without affecting its form, fit, and
function. Parts that do not meet these requirements are rejected
during quality audits.
This paper discusses how the Technology group integrates this
quality assurance tool into the PDP and how the tool plays a major
role in helping the HSE department in its goal towards eliminating
HSE incidents. The PDP involves a thorough risk assessment and
establishes a method to address those risks during the design stage.
An illustration shows how GD&T helped reduce safety risks by
ergonomically improving assembling operations. A brief discussion
explains how tolerances provided on a part help prevent finger injury.
This tool has equipped Technology to produce fixtures, which are
used daily in operations as well as manufacturing. By applying
GD&T to create good fits, HSE risks are mitigated for operating
personnel. Both customers and service providers benefit from
reduced safety risks.
Abstract: Modern Society is strongly dependent on a reliable
power supply. The availability of cheap and reliable supply of
electrical energy is an indicator of societal welfare. Uninterrupted
reliable operation of a modern power system depends to a great
extent on reliable and satisfactory performance of insulators under
different environmental conditions. This paper reports result of
natural pollution tests that have been done at sites around city of
Aligarh (India). Flashover voltage per insulation distance (FOVUID)
of porcelain disc insulator for different pH values, ESDD has been
recorded for proper correlation between electrical and chemical
parameters. The pH of the contaminants has been suggested to be an
effective pollution severity indicator and may be used as a diagnostic
parameter for proper maintenance of porcelain insulators.
Abstract: Bionanotechnology deals with nanoscopic interactions between nanostructured materials and biological systems. Polymer nanocomposites with optimized biological activity have attracted great attention. Nanoclay is considered as reinforcing nanofiller in manufacturing of high performance nanocomposites. In current study, organomodified-nanoclay with negatively charged silicate layers was incorporated into biomedical grade silicone rubber. Nanoparticle loading has been tailored to enhance cell behavior. Addition of nanoparticles led to improved mechanical properties of substrate with enhanced strength and stiffness while no toxic effects was observed. Results indicated improved viability and proliferation of cells by addition of nanofillers. The improved mechanical properties of the matrix result in proper cell response through adjustment and arrangement of cytoskeletal fibers. Results can be applied in tissue engineering when enhanced substrates are required for improvement of cell behavior for in vivo applications.
Abstract: Recent research result has shown that two multidelay
feedback systems can synchronize each other under different
schemes, i.e. lag, projective-lag, anticipating, or projectiveanticipating
synchronization. There, the driving signal is significantly
complex due that it is constituted by multiple nonlinear transformations
of delayed state variable. In this paper, a secure communication
model is proposed based on synchronization of coupled multidelay
feedback systems, in which the plain signal is mixed with a complex
signal at the transmitter side and it is precisely retrieved at the receiver
side. The effectiveness of the proposed model is demonstrated and
verified in the specific example, where the message signal is masked
directly by the complex signal and security is examined under the
breaking method of power spectrum analysis.
Abstract: In this paper we proposed the use of Huffman
coding to reduce the PAR of an OFDM system as a distortionless
scrambling technique, and we utilize the amount saved in the
total bit rate by the Huffman coding to send the encoding table
for accurate decoding at the receiver without reducing the
effective throughput. We found that the use of Huffman coding
reduces the PAR by about 6 dB. Also we have investigated the
effect of PAR reduction due to Huffman coding through testing
the spectral spreading and the inband distortion due to HPA with
different IBO values. We found a complete match of our
expectation from the proposed solution with the obtained
simulation results.