Abstract: In this research, a questionnaire survey was conducted
to measure nap, drowsiness and fatigue of drivers who work for long
shifts, to discuss about the work environment and health conditions for
taxi and bus drivers who work at night-time. The questionnaire sheet
used for this research was organized into the following categories:
tension/tiredness, drowsiness while driving, and the nap situation
during night-time work. The number of taxi drivers was 127 and the
number of bus drivers was 40. Concerning the results of a comparison
of nap hours of taxi and bus drivers, the taxi drivers’ nap hours are
overwhelmingly shorter, and also the frequency of drivers who
experience drowsiness is higher. The burden on bus drivers does not
change because of the system of a two-driver rotation shift. In
particular, the working environment of the taxi driver may lead to
greater fatigue accumulation than the bus driver’s environment.
Abstract: New environmental regulations and the increasing
market preference for companies that respect the ecosystem had
encouraged the industry to look after new treatments for its effluents.
The sugar industry, one of the largest emitter of environmental
pollutants, follows this tendency. Membrane technology is
convenient for separation of suspended solids, colloids and high
molecular weight materials that are present in a wastewater from
sugar industry. The idea is to microfilter the wastewater, where the
permeate passes through the membrane and becomes available for
recycle and re-use in the sugar manufacturing process. For
microfiltration of this effluent a tubular ceramic membrane was used
with a pore size of 200 nm at transmembrane pressure in range of 1–3
bars and in range of flow rate of 50–150 l/h. Kenics static mixer was
used for permeate flux enhancement. Turbidity and suspended solids
were removed and the permeate flux was continuously monitored
during the microfiltration process. The flux achieved after 90 minutes
of microfiltration was in a range of 50–70 l/m2h. The obtained
turbidity decrease was in the range of 50-99 % and total amount of
suspended solids was removed.
Abstract: Industries produce millions of cubic meters of effluent
every year and the wastewater produced may be released into the
surrounding water bodies, treated on-site or at municipal treatment
plants. The determination of organic matter in the wastewater
generated is very important to avoid any negative effect on the
aquatic ecosystem. The scope of the present work is to assess the
physicochemical composition of the wastewater produced from one
of the brewery industry in South Africa. This is to estimate the
environmental impact of its discharge into the receiving water bodies
or the municipal treatment plant. The parameters monitored for the
quantitative analysis of brewery wastewater include biological
oxygen demand (BOD5), chemical oxygen demand (COD), total
suspended solids, volatile suspended solids, ammonia, total oxidized
nitrogen, nitrate, nitrite, phosphorus and alkalinity content. In
average, the COD concentration of the brewery effluent was 5340.97
mg/l with average pH values of 4.0 to 6.7. The BOD5 and the solids
content of the wastewater from the brewery industry were high. This
means that the effluent is very rich in organic content and its
discharge into the water bodies or the municipal treatment plant could
cause environmental pollution or damage the treatment plant. In
addition, there were variations in the wastewater composition
throughout the monitoring period. This might be as a result of
different activities that take place during the production process, as
well as the effects of peak period of beer production on the water
usage.
Abstract: Tannase (tannin acyl hydrolase, E.C.3.1.1.20) is an
important hydrolysable enzyme with innumerable applications and
industrial potential. In the present study, a kinetic model has been
developed for the batch fermentation used for the production of
tannase by A.flavus MTCC 3783. Maximum tannase activity of
143.30 U/ml was obtained at 96 hours under optimum operating
conditions at 35oC, an initial pH of 5.5 and with an inducer tannic
acid concentration of 3% (w/v) for a fermentation period of 120
hours. The biomass concentration reaches a maximum of 6.62 g/l at
96 hours and further there was no increase in biomass concentration
till the end of the fermentation. Various unstructured kinetic models
were analyzed to simulate the experimental values of microbial
growth, tannase activity and substrate concentration. The Logistic
model for microbial growth , Luedeking - Piret model for production
of tannase and Substrate utilization kinetic model for utilization of
substrate were capable of predicting the fermentation profile with
high coefficient of determination (R2) values of 0.980, 0.942 and
0.983 respectively. The results indicated that the unstructured models
were able to describe the fermentation kinetics more effectively.
Abstract: This paper applied factor conditions from Porter’s
Diamond Model (1990) to understand the various challenges facing
the AMISA. Factor conditions highlighted in Porter’s model are
grouped into two groups namely, basic and advance factors. Two
AMISA associations representing over 10 000 employees were
interviewed. The largest Clothing, Textiles and Leather (CTL)
apparel retail group was also interviewed with a government
department implementing the industrialization policy were
interviewed. The paper points out that AMISA have basic factor conditions
necessary for competitive advantage in the apparel industries.
However advance factor creation has proven to be a challenge for
AMISA, Higher Education Institutions (HEIs) and government. Poor
infrastructural maintenance has contributed to high manufacturing
costs and poor quick response technologies. The use of Porter’s
Factor Conditions as a tool to analyze the sector’s competitive
advantage challenges and opportunities has increased knowledge
regarding factors that limit the AMISA’s competitiveness. It is
therefore argued that other studies on Porter’s Diamond model
factors like Demand conditions, Firm strategy, structure and rivalry
and Related and supporting industries can be used to analyze the
situation of the AMISA for the purposes of improving competitive
advantage.
Abstract: Tool, Die and Mould-making (TDM) firms have been
known to play a pivotal role in the growth and development of the
manufacturing sectors in most economies. Their output contributes
significantly to the quality, cost and delivery speed of final
manufactured parts. Unfortunately, the South African Tool, Die and
Mould-making manufacturers have not been competing on the local
or global market in a significant way. This reality has hampered the
productivity and growth of the sector thus attracting intervention. The
paper explores the shortcomings South African toolmakers have to
overcome to restore their competitive position globally. Results from
a global benchmarking survey on the tooling sector are used to
establish a roadmap of what South African toolmakers can do to
become a productive, World Class force on the global market.
Abstract: Chalcopyrite (CuFeS2) is the most common primary
mineral used for the commercial production of copper. The low
dissolution efficiency of chalcopyrite in sulfate media has prevented
an efficient industrial leaching of this mineral in sulfate media. Ferric
ions, bacteria, oxygen and other oxidants have been used as oxidizing
agents in the leaching of chalcopyrite in sulfate and chloride media
under atmospheric or pressure leaching conditions. Two leaching
methods were studied to evaluate chalcopyrite (CuFeS2) dissolution
in acid media. First, the conventional oxidative acid leaching method
was carried out using sulfuric acid (H2SO4) and potassium
dichromate (K2Cr2O7) as oxidant at atmospheric pressure. Second,
microwave-assisted acid leaching was performed using the
microwave accelerated reaction system (MARS) for same reaction
media. Parameters affecting the copper extraction such as leaching
time, leaching temperature, concentration of H2SO4 and
concentration of K2Cr2O7 were investigated. The results of
conventional acid leaching experiments were compared to the
microwave leaching method. It was found that the copper extraction
obtained under high temperature and high concentrations of oxidant
with microwave leaching is higher than those obtained
conventionally. 81% copper extraction was obtained by the
conventional oxidative acid leaching method in 180 min, with the
concentration of 0.3 mol/L K2Cr2O7 in 0.5M H2SO4 at 50 ºC, while
93.5% copper extraction was obtained in 60 min with microwave
leaching method under same conditions.
Abstract: The purpose of this project is to propose a quick and
environmentally friendly alternative to measure the quality of oils
used in food industry. There is evidence that repeated and
indiscriminate use of oils in food processing cause physicochemical
changes with formation of potentially toxic compounds that can
affect the health of consumers and cause organoleptic changes. In
order to assess the quality of oils, non-destructive optical techniques
such as Interferometry offer a rapid alternative to the use of reagents,
using only the interaction of light on the oil. Through this project, we
used interferograms of samples of oil placed under different heating
conditions to establish the changes in their quality. These
interferograms were obtained by means of a Mach-Zehnder
Interferometer using a beam of light from a HeNe laser of 10mW at
632.8nm. Each interferogram was captured, analyzed and measured
full width at half-maximum (FWHM) using the software from
Amcap and ImageJ. The total of FWHMs was organized in three
groups. It was observed that the average obtained from each of the
FWHMs of group A shows a behavior that is almost linear, therefore
it is probable that the exposure time is not relevant when the oil is
kept under constant temperature. Group B exhibits a slight
exponential model when temperature raises between 373 K and 393
K. Results of the t-Student show a probability of 95% (0.05) of the
existence of variation in the molecular composition of both samples.
Furthermore, we found a correlation between the Iodine Indexes
(Physicochemical Analysis) and the Interferograms (Optical
Analysis) of group C. Based on these results, this project highlights
the importance of the quality of the oils used in food industry and
shows how Interferometry can be a useful tool for this purpose.
Abstract: HR is a department that enhances the power of
employee performance in regard with their services, and to make the
organization strategic objectives. The main concern of HR
department is to organize people, focus on policies and their system.
The empirical study shows the relationship between HRM (Human
Resource Management practices) and their Job Satisfaction. The
Hypothesis is testing on a sample of overall 320 employees of 5
different Pharmaceutical departments of different organizations in
Pakistan. The important thing as Relationship of Job satisfaction with
HR Practices, Impact on Job Satisfaction with HR Practices,
Participation of Staff of Different Departments, HR Practices effects
the Job satisfaction, Recruitment or Hiring and Selection effects the
Job satisfaction, Training and Development, Performance and
Appraisals, Compensation affects the Job satisfaction , and Industrial
Relationships affects the Job satisfaction. After finishing all data
analysis, the conclusion is that lots of Job related activities raise the
confidence of Job satisfaction of employees with their salary and
other benefits.
Abstract: A Rice Sheller is used for obtaining polished white
rice from paddy. There are about 3000 Rice Shellers in Punjab and
50000 in India. During the process of shelling lot of dust is emitted
from different unit operations like paddy silo, paddy shaker, bucket
elevators, huskers, paddy separator etc. These dust emissions have
adverse effect on the health of the workers and the wear and tear of
the shelling machinery is fast. All the dust emissions spewing out of
these unit operations of a rice Sheller were contained by providing
suitable hoods and enclosures while ensuring their workability. These
were sucked by providing an induced draft fan followed by a high
efficiency cyclone separator that has got an overall dust collection
efficiency of more than 90%. This cyclone separator replaced two
cyclone separators and a filter bag house, which the Rice Sheller was
already having. The dust concentration in the stack after the
installation of cyclone separator is well within the stipulated
standards. Besides controlling pollution, there is improvement in the
quality of products like bran and the life of shelling machinery has
enhanced. The payback period of this technology is less than four
shelling months.
Abstract: This contribution presents a friction estimator for
industrial purposes which identifies Coulomb friction in a steering
system. The estimator only needs a few, usually known, steering
system parameters. Friction occurs on almost every mechanical
system and has a negative influence on high-precision position
control. This is demonstrated on a steering angle controller for highly
automated driving. In this steering system the friction induces limit
cycles which cause oscillating vehicle movement when the vehicle
follows a given reference trajectory. When compensating the friction
with the introduced estimator, limit cycles can be suppressed. This
is demonstrated by measurements in a series vehicle.
Abstract: In recent years, honeycomb fiber reinforced plastic
(FRP) sandwich panels have been increasingly used in various
industries. Low weight, low price and high mechanical strength are
the benefits of these structures. However, their mechanical properties
and behavior have not been fully explored. The objective of this
study is to conduct a combined numerical-statistical investigation of
honeycomb FRP sandwich beams subject to torsion load. In this
paper, the effect of geometric parameters of sandwich panel on
maximum shear strain in both face and core and angle of torsion in a
honeycomb FRP sandwich structures in torsion is investigated. The
effect of Parameters including core thickness, face skin thickness,
cell shape, cell size, and cell thickness on mechanical behavior of the
structure were numerically investigated. Main effects of factors were
considered in this paper and regression equations were derived.
Taguchi method was employed as experimental design and an
optimum parameter combination for the maximum structure stiffness
has been obtained. The results showed that cell size and face skin
thickness have the most significant impacts on torsion angle,
maximum shear strain in face and core.
Abstract: The purpose of the paper is to address the strategic
risk issues surrounding Hindi film distribution in Mumbai for a film
distributor, who acts as an entrepreneur when launching a product
(movie) in the market (film territory).The paper undertakes a
fundamental review of films and risk in the Hindi film industry and
applies Grounded Theory technique to understand the complex
phenomena of risk taking behavior of the film distributors (both
independent and studios) in Mumbai. Rich in-depth interviews with
distributors are coded to develop core categories through constant
comparison leading to conceptualization of the phenomena of
interest. This paper is a first-of-its-kind-attempt to understand risk
behavior of a distributor, which is akin to entrepreneurial risk
behavior under conditions of uncertainty.
Abstract: In recent research copper and manganese systems
were found to be the most active in CO and organic compounds
oxidation among the base catalysts. The mixed copper manganese
oxide has been widely studied in oxidation reactions because of their
higher activity at low temperatures in comparison with single oxide
catalysts. The results showed that the formation of spinel
CuxMn3−xO4 in the oxidized catalyst is responsible for the activity
even at room temperature. That is why the most of the investigations
are focused on the hopcalite catalyst (CuMn2O4) as the best coppermanganese
catalyst. Now it’s known that this is true only for CO
oxidation, but not for mixture of CO and VOCs. The purpose of this
study is to investigate the alumina supported copper-manganese
catalysts with different Cu/Mn molar ratio in terms of oxidation of
CO, methanol and dimethyl ether. The catalysts were prepared by impregnation of γ-Al2O3 with
copper and manganese nitrates and the catalytic activity
measurements were carried out in two stage continuous flow
equipment with an adiabatic reactor for simultaneous oxidation of all
compounds under the conditions closest possible to the industrial. Gas
mixtures on the input and output of the reactor were analyzed with a
gas chromatograph, equipped with FID and TCD detectors. The
texture characteristics were determined by low-temperature (- 196oС)
nitrogen adsorption in a Quantachrome Instruments NOVA 1200e
(USA) specific surface area & pore analyzer. Thermal, XRD and
TPR analyses were performed. It was established that the active component of the mixed Cu-
Mn/γ–alumina catalysts strongly depends on the Cu/Mn molar ratio.
Highly active alumina supported Cu-Mn catalysts for CO, methanol
and DME oxidation were synthesized. While the hopcalite is the best
catalyst for CO oxidation, the best compromise for simultaneous
oxidation of all components is the catalyst with Cu/Mn molar ratio
1:5.
Abstract: In this paper air quality conditions in Makkah and
Leeds are compared. These two cities have totally different climatic
conditions. Makkah climate is characterised as hot and dry (arid)
whereas that of Leeds is characterised as cold and wet (temperate).
This study uses air quality data from 2012 collected in Makkah,
Saudi Arabia and Leeds, UK. The concentrations of all pollutants,
except NO are higher in Makkah. Most notable, the concentrations of
PM10 are much higher in Makkah than in Leeds. This is probably due
to the arid nature of climatic conditions in Makkah and not solely due
to anthropogenic emission sources, otherwise like PM10 some of the
other pollutants, such as CO, NO, and SO2 would have shown much
greater difference between Leeds and Makkah. Correlation analysis is
performed between different pollutants at the same site and the same
pollutants at different sites. In Leeds the correlation between PM10
and other pollutants is significantly stronger than in Makkah. Weaker
correlation in Makkah is probably due to the fact that in Makkah
most of the gaseous pollutants are emitted by combustion processes,
whereas most of the PM10 is generated by other sources, such as
windblown dust, re-suspension, and construction activities. This is in
contrast to Leeds where all pollutants including PM10 are
predominantly emitted by combustions, such as road traffic.
Furthermore, in Leeds frequent rains wash out most of the
atmospheric particulate matter and suppress re-suspension of dust.
Temporal trends of various pollutants are compared and discussed.
This study emphasises the role of climatic conditions in managing air
quality, and hence the need for region-specific controlling strategies
according to the local climatic and meteorological conditions.
Abstract: This paper aims to project the construction of a
prototype azimuthal thruster, mounted with materials of low cost and
easy access, testing in a controlled environment to measure their
performance, characteristics and feasibility of future projects. The
construction of the simulation of dynamic positioning software,
responsible for simulating a vessel and reposition it when necessary.
Validation tests were performed in the form of partial or complete
system. These tests validate the system manually or automatically.
The system provides an interface to the user and simulates the
conditions unfavorable positioning of a vessel, accurately calculates
the azimuth angle, the direction of rotation of the helix and the time
that this should be turned on so that the vessel back to position
original. A serial communication connects the Simulation Dynamic
Positioning System with Embedded System causing the usergenerated
data to simulate the DP system arrives in the form of
control signals to the motors of the propellant. This article addresses
issues in the marine industry employees.
Abstract: Zn alloy and composite coatings are widely used in
buildings and structures, automobile and fasteners industries to
protect steel component from corrosion. In this paper, Zn-Ni-Al2O3
nanocomposite coatings were electrodeposited on mild steel using a
novel sol enhanced electroplating method. In this method, transparent
Al2O3 sol was added into the acidic Zn-Ni bath to produced Zn-Ni-
Al2O3 nanocomposite coatings. The effect of alumina sol on the
electrodeposition process, and coating properties was investigated
using cyclic voltammetry, XRD, ESEM and Tafel test. Results from
XRD tests showed that the structure of all coatings was single γ-
Ni5Zn21 phase. Cyclic voltammetry results showed that the
electrodeposition overpotential was lower in the presence of alumina
sol in the bath, and caused the reduction potential of Zn-Ni to shift to
more positive values. Zn-Ni-Al2O3 nanocomposite coatings produced
more uniform and compact deposits, with fine grained microstructure
when compared to Zn-Ni coatings. The corrosion resistance of Zn-Ni
coatings was improved significantly by incorporation of alumina
nanoparticles into the coatings.
Abstract: The using of waste materials in the construction
industry can reduce the dependence on the natural aggregates which
are going at the end to deplete. The glass waste is generated in a huge
amount which can make one of its disposals in concrete industry
effective not only as a green solution but also as an advantage to
enhance the performance of mechanical properties and durability of
concrete. This article reports the performance of concrete specimens
containing different percentages of milled glass waste as a partial
replacement of cement (Powder), when they are subject to cycles of
freezing and thawing. The tests were conducted on 75-mm cubes and
75 x 75 x 300-mm prisms. Compressive strength based on laboratory
testing and non-destructive ultrasonic pulse velocity test were
performed during the action of freezing-thawing cycles (F/T). The
results revealed that the incorporation of glass waste in concrete
mixtures is not only feasible but also showed generally better strength
and durability performance than control concrete mixture. It may be
said that the recycling of waste glass in concrete mixes is not only a
disposal way, but also it can be an exploitation in concrete industry.
Abstract: The work aims to develop a robot in the form of
autonomous vehicle to detect, inspection and mapping of
underground pipelines through the ATmega328 Arduino platform.
Hardware prototyping is very similar to C / C ++ language that
facilitates its use in robotics open source, resembles PLC used in
large industrial processes. The robot will traverse the surface
independently of direct human action, in order to automate the
process of detecting buried pipes, guided by electromagnetic
induction. The induction comes from coils that send the signal to the
Arduino microcontroller contained in that will make the difference in
intensity and the treatment of the information, and then this
determines actions to electrical components such as relays and
motors, allowing the prototype to move on the surface and getting the
necessary information. This change of direction is performed by a
stepper motor with a servo motor. The robot was developed by
electrical and electronic assemblies that allowed test your application.
The assembly is made up of metal detector coils, circuit boards and
microprocessor, which interconnected circuits previously developed
can determine, process control and mechanical actions for a robot
(autonomous car) that will make the detection and mapping of buried
pipelines plates. This type of prototype can prevent and identifies
possible landslides and they can prevent the buried pipelines suffer an
external pressure on the walls with the possibility of oil leakage and
thus pollute the environment.
Abstract: This paper concludes that, for economic development,
and to ensure survival, Kenya and similar countries must industrialize
their economy and mechanize their agriculture using modern large
scale methods.