Abstract: The excessive consumption of fossil energies (electrical energy) during summer caused by the technological development involves more and more climate warming.
In order to reduce the worst impact of gas emissions produced from classical air conditioning, heat driven solar absorption chiller is pretty promising; it consists on using solar as motive energy which is clean and environmentally friendly to provide cold.
Solar absorption machine is composed by four components using Lithium Bromide /water as a refrigerating couple. LiBr- water is the most promising in chiller applications due to high safety, high volatility ratio, high affinity, high stability and its high latent heat. The lithium bromide solution is constitute by the salt lithium bromide which absorbs water under certain conditions of pressure and temperature however if the concentration of the solution is high in the absorption chillers; which exceed 70%, the solution will crystallize.
The main aim of this article is to study the phenomena of the crystallization and to evaluate how the dependence between the electric conductivity and the concentration which should be controlled.
Abstract: Characterized as rich mineral substances, low
temperature, few bacteria, and stability with numerous implementation
aspects on aquaculture, food, drinking, and leisure, the deep sea water
(DSW) development has become a new industry in the world. It has
been report that marine algae contain various biologically active
compounds. This research focued on the affections in cultivating
Sagrassum cristaefolium with different concentration of deep sea
water(DSW) and surface sea water(SSW). After two and four weeks,
the total phenolic contents were compared in Sagrassum cristaefolium
culturing with different ways, and the reductive activity of them was
also be tried with potassium ferricyanide. Those fresh seaweeds were
dried with oven and were ground to powder. Progressively, the marine
algae we cultured was extracted by water under the condition with
heating them at 90Ôäâ for 1hr.The total phenolic contents were be
executed using Folin–Ciocalteu method. The results were explaining
as follows: the highest total phenolic contents and the best reductive
ability of all could be observed on the 1/4 proportion of DSW to SSW
culturing in two weeks. Furthermore, the 1/2 proportion of DSW to
SSW also showed good reductive ability and plentiful phenolic
compositions. Finally, we confirmed that difference proportion of
DSW and SSW is the major point relating to ether the total phenolic
components or the reductive ability in the Sagrassum cristaefolium. In
the future, we will use this way to mass production the marine algae or
other micro algae on industry applications.
Abstract: Most paddy rice fields in East Asia are small parcels,
and the weather conditions during the growing season are usually
cloudy. FORMOSAT-2 multi-spectral images have an 8-meter
resolution and one-day recurrence, ideal for mapping paddy rice fields
in East Asia. To map rice fields, this study first determined the
transplanting and the most active tillering stages of paddy rice and
then used multi-temporal images to distinguish different growing
characteristics between paddy rice and other ground covers. The
unsupervised ISODATA (iterative self-organizing data analysis
techniques) and supervised maximum likelihood were both used to
discriminate paddy rice fields, with training areas automatically
derived from ten-year cultivation parcels in Taiwan. Besides original
bands in multi-spectral images, we also generated normalized
difference vegetation index and experimented with object-based
pre-classification and post-classification. This paper discusses results
of different image classification methods in an attempt to find a
precise and automatic solution to mapping paddy rice in Taiwan.
Abstract: This paper presents the fundamentals of Origami engineering and its application in nowadays as well as future industry. Several main cores of mathematical approaches such as Huzita- Hatori axioms, Maekawa and Kawasaki-s theorems are introduced briefly. Meanwhile flaps and circle packing by Robert Lang is explained to make understood the underlying principles in designing crease pattern. Rigid origami and its corrugation patterns which are potentially applicable for creating transformable or temporary spaces is discussed to show the transition of origami from paper to thick material. Moreover, some innovative applications of origami such as eyeglass, origami stent and high tech origami based on mentioned theories and principles are showcased in section III; while some updated origami technology such as Vacuumatics, self-folding of polymer sheets and programmable matter folding which could greatlyenhance origami structureare demonstrated in Section IV to offer more insight in future origami.
Abstract: This paper describes vibration analysis using the finite
element method for a small earphone, especially for the diaphragm
shape with a low-rigidity. The viscoelastic diaphragm is supported by
multiple nonlinear concentrated springs with linear hysteresis
damping. The restoring forces of the nonlinear springs have cubic
nonlinearity. The finite elements for the nonlinear springs with
hysteresis are expressed and are connected to the diaphragm that is
modeled by linear solid finite elements in consideration of a complex
modulus of elasticity. Further, the discretized equations in physical
coordinates are transformed into the nonlinear ordinary coupled
equations using normal coordinates corresponding to the linear natural
modes. We computed the nonlinear stationary and non-stationary
responses due to the internal resonance between modes with large
amplitude in the nonlinear springs and elastic modes in the diaphragm.
The non-stationary motions are confirmed as the chaos due to the
maximum Lyapunov exponents with a positive number. From the time
histories of the deformation distribution in the chaotic vibration, we
identified nonlinear modal couplings.
Abstract: Tourism is a phenomenon respected by the human communities since a long time ago. It has been evoloving continually based on a variety of social and economic needs and with respect to increasingly development of communication and considerable increase of tourist-s number and resulted exchange income has attained much out come such as employment for the communities. or the purpose of tourism development in this zone suitable times and locations need to be specified in the zone for the tourist-s attendance. One of the most important needs of the tourists is the knowledge of climate conditions and suitable times for sightseeing. In this survey, the climate trend condition has been identified for attending the tourists in Isfahan province using the modified tourism climate index (TCI) as well as SPSS, GIS, excel, surfer softwares. This index evoluates systematically the climate conditions for tourism affairs and activities using the monthly maximum mean parameters of daily temperature, daily mean temperature, minimum relative humidity, daily mean relative humidity, precipitation (mm), total sunny hours, wind speed and dust. The results obtaind using kendal-s correlation test show that the months January, February, March, April, May, June, July, August, September, October, November and December are significant and have an increasing trend that indicates the best condition for attending the tourists. S, P, T mean , T max and dust are estimated from 1976-2005 and do kendal-s correlation test again to see which parameter has been effective. Based on the test, we also observed on the effective parameters that the rate of dust in February, March, April, May, June, July, August, October and November is decreasing and precipitation in September and January is increasing and also the radiation rate in May and August is increasing that indicate a better condition of convenience. Maximum temperature in June is also decreasing. Isfahan province has two spring and fall peaks and the best places for tourism are in the north and western areas.
Abstract: This paper presented a proposed design for
transcutaneous inductive powering links. The design used to transfer
power and data to the implanted devices such as implanted
Microsystems to stimulate and monitoring the nerves and muscles.
The system operated with low band frequency 13.56 MHZ according
to industrial- scientific – medical (ISM) band to avoid the tissue
heating. For external part, the modulation index is 13 % and the
modulation rate 7.3% with data rate 1 Mbit/s assuming Tbit=1us. The
system has been designed using 0.35-μm fabricated CMOS
technology. The mathematical model is given and the design is
simulated using OrCAD P Spice 16.2 software tool and for real-time
simulation the electronic workbench MULISIM 11 has been used.
The novel circular plane (pancake) coils was simulated using
ANSOFT- HFss software.
Abstract: This paper presents a review on published literature
and experimental works on local sands for possible use as proppant,
specifically those from Terengganu coastal area. This includes
examination on characteristics of sand samples and selection of
experiments for proppant testing. Sand samples from identified areas
were tested according to particle size distribution, density, roundness
and sphericity, turbidity and mineralogy. Results from sand samples
were compared against proppant specifications set by API RP 56 and
selected commercial proppants. The present study found that the size
distribution, sphericity, turbidity and bulk density of Terengganu
sands are at par with some of commercial proppants. Nevertheless,
Terengganu sand samples do not completely surpass the required
roundness for use as proppant.
Abstract: There is an ongoing controversy in the literature related
to the biological effects of weak, low frequency electromagnetic
fields. The physical arguments and interpretation of the experimental
evidence are inconsistent, where some physical arguments and
experimental demonstrations tend to reject the likelihood of any
effect of the fields at extremely low level. The problem arises of
explaining, how the low-energy influences of weak magnetic fields
can compete with the thermal and electrical noise of cells at normal
temperature using the theoretical studies. The magnetoreception in
animals involve radical pair mechanism. The same mechanism has
been shown to be involved in the circadian rhythm synchronization in
mammals. These reactions can be influenced by the weak magnetic
fields. Hence, it is postulated the biological clock can be affected
by weak magnetic fields and these disruptions to the rhythm can
cause adverse biological effects. In this paper, likelihood of altering
the biological clock via the radical pair mechanism is analyzed to
simplify these studies of controversy.
Abstract: Warehousing is commonly used in factories for the
storage of products until delivery of orders. As the amount of
products stored increases it becomes tedious to be carried out
manually. In recent years, the manual storing has converted into fully
or partially computer controlled systems, also known as Automated
Storage and Retrieval Systems (AS/RS). This paper discusses an
ASRS system, which was designed such that the best storage location
for the products is determined by utilizing a fuzzy control system.
The design maintains the records of the products to be/already in
store and the storage/retrieval times along with the availability status
of the storage locations. This paper discusses on the maintenance of
the above mentioned records and the utilization of the concept of
fuzzy logic in order to determine the optimum storage location for
the products. The paper will further discuss on the dynamic splitting
and merging of the storage locations depending on the product sizes.
Abstract: One of the disadvantages of using OFDM is the larger
peak to averaged power ratio (PAPR) in its time domain signal. The
larger PAPR signal would course the fatal degradation of bit error
rate performance (BER) due to the inter-modulation noise in the nonlinear
channel. This paper proposes an improved DSI (Dummy
Sequence Insertion) method, which can achieve the better PAPR and
BER performances. The feature of proposed method is to optimize
the phase of each dummy sub-carrier so as to reduce the PAPR
performance by changing all predetermined phase coefficients in the
time domain signal, which is calculated for data sub-carriers and
dummy sub-carriers separately. To achieve the better PAPR
performance, this paper also proposes to employ the time-frequency
domain swapping algorithm for fine adjustment of phase coefficient
of the dummy subcarriers, which can achieve the less complexity of
processing and achieves the better PAPR and BER performances
than those for the conventional DSI method. This paper presents
various computer simulation results to verify the effectiveness of
proposed method as comparing with the conventional methods in the
non-linear channel.
Abstract: Transferring information developed by other peoples is an ordinary event that happens during daily conversations, for example when employees sea each other in the organization, or when they are having lunch together, or attending a meeting, they use to talk about their experience, and discuss about their current projects, and talk about their successes over some specific problems. Despite the potential value of leveraging organizational memory and expertise by using OMS and ER, still small organizations haven-t been able to capitalize on its promised value. Each organization has its internal knowledge management system, in some of organizations the system face the lack of expert people to save their experience in the repository and in another hand on some other organizations there are lots of expert people but the organization doesn-t have the maximum use of their knowledge.
Abstract: A new supported liquid membrane (SLM) system for
the selective transport of VO2
+ ions was prepared in this present
work. The SLM was a thin porous polyvinylidene difluoride
(PVDF) membrane soaked with Di-(2-ethylhexyl) phosphoric acid
(D2EHPA) as mobile carrier in Xylene as organic solvent.
D2EHPA acts as a highly selective carrier for the uphill transport of
VO2
+ ions through the SLM. The transport of VO2
+ ions reached to
64%. In the presence of P2O7-2 ion as suitable masking agent in the
feed solution, the interfering effects of other cations were eliminated.
Abstract: Mobile Ad hoc Networks is an autonomous system of
mobile nodes connected by multi-hop wireless links without
centralized infrastructure support. As mobile communication gains
popularity, the need for suitable ad hoc routing protocols will
continue to grow. Efficient dynamic routing is an important research
challenge in such a network. Bandwidth constrained mobile devices
use on-demand approach in their routing protocols because of its
effectiveness and efficiency. Many researchers have conducted
numerous simulations for comparing the performance of these
protocols under varying conditions and constraints. Most of them are
not aware of MAC Protocols, which will impact the relative
performance of routing protocols considered in different network
scenarios. In this paper we investigate the choice of MAC protocols
affects the relative performance of ad hoc routing protocols under
different scenarios. We have evaluated the performance of these
protocols using NS2 simulations. Our results show that the
performance of routing protocols of ad hoc networks will suffer when
run over different MAC Layer protocols.
Abstract: This article presents the results using a parametric approach and a Wavelet Transform in analysing signals emitting from the sperm whale. The extraction of intrinsic characteristics of these unique signals emitted by marine mammals is still at present a difficult exercise for various reasons: firstly, it concerns non-stationary signals, and secondly, these signals are obstructed by interfering background noise. In this article, we compare the advantages and disadvantages of both methods: Auto Regressive models and Wavelet Transform. These approaches serve as an alternative to the commonly used estimators which are based on the Fourier Transform for which the hypotheses necessary for its application are in certain cases, not sufficiently proven. These modern approaches provide effective results particularly for the periodic tracking of the signal's characteristics and notably when the signal-to-noise ratio negatively effects signal tracking. Our objectives are twofold. Our first goal is to identify the animal through its acoustic signature. This includes recognition of the marine mammal species and ultimately of the individual animal (within the species). The second is much more ambitious and directly involves the intervention of cetologists to study the sounds emitted by marine mammals in an effort to characterize their behaviour. We are working on an approach based on the recordings of marine mammal signals and the findings from this data result from the Wavelet Transform. This article will explore the reasons for using this approach. In addition, thanks to the use of new processors, these algorithms once heavy in calculation time can be integrated in a real-time system.
Abstract: Lung cancer accounts for the most cancer related deaths for men as well as for women. The identification of cancer associated genes and the related pathways are essential to provide an important possibility in the prevention of many types of cancer. In this work two filter approaches, namely the information gain and the biomarker identifier (BMI) are used for the identification of different types of small-cell and non-small-cell lung cancer. A new method to determine the BMI thresholds is proposed to prioritize genes (i.e., primary, secondary and tertiary) using a k-means clustering approach. Sets of key genes were identified that can be found in several pathways. It turned out that the modified BMI is well suited for microarray data and therefore BMI is proposed as a powerful tool for the search for new and so far undiscovered genes related to cancer.
Abstract: One of object oriented software developing problem
is the difficulty of searching the appropriate and suitable objects for
starting the system. In this work, ontologies appear in the part of
supporting the object discovering in the initial of object oriented
software developing. There are many researches try to demonstrate
that there is a great potential between object model and ontologies.
Constructing ontology from object model is called ontology
engineering can be done; On the other hand, this research is aiming to
support the idea of building object model from ontology is also
promising and practical. Ontology classes are available online in any
specific areas, which can be searched by semantic search engine.
There are also many helping tools to do so; one of them which are
used in this research is Protégé ontology editor and Visual Paradigm.
To put them together give a great outcome. This research will be
shown how it works efficiently with the real case study by using
ontology classes in travel/tourism domain area. It needs to combine
classes, properties, and relationships from more than two ontologies
in order to generate the object model. In this paper presents a simple
methodology framework which explains the process of discovering
objects. The results show that this framework has great value while
there is possible for expansion. Reusing of existing ontologies offers
a much cheaper alternative than building new ones from scratch.
More ontologies are becoming available on the web, and online
ontologies libraries for storing and indexing ontologies are increasing
in number and demand. Semantic and Ontologies search engines have
also started to appear, to facilitate search and retrieval of online
ontologies.
Abstract: Video sensor networks operate on stringent requirements
of latency. Packets have a deadline within which they have
to be delivered. Violation of the deadline causes a packet to be
treated as lost and the loss of packets ultimately affects the quality
of the application. Network latency is typically a function of many
interacting components. In this paper, we propose ways of reducing
the forwarding latency of a packet at intermediate nodes. The
forwarding latency is caused by a combination of processing delay
and queueing delay. The former is incurred in order to determine the
next hop in dynamic routing. We show that unless link failures in a
very specific and unlikely pattern, a vast majority of these lookups
are redundant. To counter this we propose source routing as the
routing strategy. However, source routing suffers from issues related
to scalability and being impervious to network dynamics. We propose
solutions to counter these and show that source routing is definitely
a viable option in practical sized video networks. We also propose a
fast and fair packet scheduling algorithm that reduces queueing delay
at the nodes. We support our claims through extensive simulation on
realistic topologies with practical traffic loads and failure patterns.
Abstract: Developing a supply chain management (SCM) system is costly, but important. However, because of its complicated nature, not many of such projects are considered successful. Few research publications directly relate to key success factors (KSFs) for implementing a SCM system. Motivated by the above, this research proposes a hierarchy of KSFs for SCM system implementation in the semiconductor industry by using a two-step approach. First, the literature review indicates the initial hierarchy. The second step includes a focus group approach to finalize the proposed KSF hierarchy by extracting valuable experiences from executives and managers that actively participated in a project, which successfully establish a seamless SCM integration between the world's largest semiconductor foundry manufacturing company and the world's largest assembly and testing company. Future project executives may refer the resulting KSF hierarchy as a checklist for SCM system implementation in semiconductor or related industries.
Abstract: This paper reports on investigations into capacity of a
Multiple Input Multiple Output (MIMO) wireless communication
system employing a uniform linear array (ULA) at the transmitter and
either a uniform linear array (ULA) or a uniform circular array (UCA)
antenna at the receiver. The transmitter is assumed to be surrounded by
scattering objects while the receiver is postulated to be free from
scattering objects. The Laplacian distribution of angle of arrival
(AOA) of a signal reaching the receiver is postulated. Calculations of
the MIMO system capacity are performed for two cases without and
with the channel estimation errors. For estimating the MIMO channel,
the scaled least square (SLS) and minimum mean square error
(MMSE) methods are considered.