Abstract: This study evaluated the microbiological quality
and the sensory characteristics of carp fillets processed by the
sousvide method when stored at 2 and 10 °C. Four different
combinations of sauced–storage were studied then stored at 2 or 10
°C was evaluate periodically sensory, microbiological and
chemical quality. Batches stored at 2 °C had lower growth rates of
mesophiles and psychrotrophs. Moreover, these counts decreased
by increasing the heating temperature and time. Staphylococcus
aureus, Bacillus cereus, Clostridium perfringens and Listeria
monocytogenes were not found in any of the samples. The heat
treatment of 90 °C for 15 min and sauced was the most effective to
ensure the safety and extend the shelf-life of sousvide carp
preserving its sensory characteristics. This study establishes the
microbiological quality of sous vide carp and emphasizes the
relevance of the raw materials, heat treatment and storage
temperature to ensure the safety of the product.
Abstract: The ability to predict an accurate temperature
distribution requires the knowledge of the losses, the thermal
characteristics of the materials, and the cooling conditions, all of
which are very difficult to quantify. In this paper, the impact of the
effects of iron and copper losses are investigated separately and
their effects on the heating in various points of the stator of an
induction motor, is highlighted by using two simple tests. In addition,
the effect of a defect, such as an open circuit in a phase of the stator,
on the heating is also obtained by a no-load test.
The squirrel cage induction motor is rated at 2.2 kW; 380 V; 5.2
A; Δ connected; 50 Hz; 1420 rpm and the class of insulation F, has
been thermally tested under several load conditions. Several
thermocouples were placed in strategic points of the stator.
Abstract: In this study the integration of an absorption heat
pump (AHP) with the concentration section of an industrial pulp and
paper process is investigated using pinch technology. The optimum
design of the proposed water-lithium bromide AHP is then achieved
by minimizing the total annual cost. A comprehensive optimization is
carried out by relaxation of all stream pressure drops as well as heat
exchanger areas involving in AHP structure. It is shown that by
applying genetic algorithm optimizer, the total annual cost of the
proposed AHP is decreased by 18% compared to one resulted from
simulation.
Abstract: Laminar natural-convective heat transfer from a
horizontal cylinder is studied by solving the Navier-Stokes and
energy equations using higher order compact scheme in cylindrical
polar coordinates. Results are obtained for Rayleigh numbers of 1,
10, 100 and 1000 for a Prandtl number of 0.7. The local Nusselt
number and mean Nusselt number are calculated and compared with
available experimental and theoretical results. Streamlines, vorticity -
lines and isotherms are plotted.
Abstract: Viscous heating becomes significant in the high speed
resin coating process of glass fibers for optical fiber manufacturing.
This study focuses on the coating resin flows inside the capillary
coating die of optical fiber coating applicator and they are numerically
simulated to examine the effects of viscous heating and subsequent
temperature increase in coating resin. Resin flows are driven by fast
moving glass fiber and the pressurization at the coating die inlet, while
the temperature dependent viscosity of liquid coating resin plays an
important role in the resin flow. It is found that the severe viscous
heating near the coating die wall profoundly alters the radial velocity
profiles and that the increase of final coating thickness by die
pressurization is amplified if viscous heating is present.
Abstract: The aim of this study is to develop mathematical
relationships for the performance parameter brake thermal efficiency
(BTE) and emission parameter nitrogen oxides (NOx) for the various
esters of vegetable oils used as CI engine fuel. The BTE is an
important performance parameter defining the ability of engine to
utilize the energy supplied and power developed similarly it is
indication of efficiency of fuels used. The esters of cottonseed oil,
soybean oil, jatropha oil and hingan oil are prepared using
transesterification process and characterized for their physical and
main fuel properties including viscosity, density, flash point and
higher heating value using standard test methods. These esters are
tried as CI engine fuel to analyze the performance and emission
parameters in comparison to diesel. The results of the study indicate
that esters as a fuel does not differ greatly with that of diesel in
properties. The CI engine performance with esters as fuel is in line
with the diesel where as the emission parameters are reduced with the
use of esters.
The correlation developed between BTE and brake power(BP),
gross calorific value(CV), air-fuel ratio(A/F), heat carried away by
cooling water(HCW). Another equation is developed between the
NOx emission and CO, HC, smoke density (SD), exhaust gas
temperature (EGT). The equations are verified by comparing the
observed and calculated values which gives the coefficient of
correlation of 0.99 and 0.96 for the BTE and NOx equations
respectively.
Abstract: How to simulate experimentally the air flow and heat
transfer under microgravity on the ground is important, which has not
been completely solved so far. Influence of gravity on air natural
convection results in convection heat transfer on ground difference
from that on orbit. In order to obtain air temperature and velocity
deviations of manned spacecraft during terrestrial thermal test,
dimensionless number analysis and numerical simulation analysis are
performed. The calculated temperature distribution and velocity
distribution of the horizontal test cases are compared to the vertical
cases. The results show that the influence of gravity is neglected for
facility drawer racks and more obvious for vertical cabins.
Abstract: The significant effects of the interactions between the
system boundaries and the near wall molecules in miniaturized
gaseous devices lead to the formation of the Knudsen layer in which
the Navier-Stokes-Fourier (NSF) equations fail to predict the correct
associated phenomena. In this paper, the well-known lattice
Boltzmann method (LBM) is employed to simulate the fluid flow and
heat transfer processes in rarefied gaseous micro media. Persuaded
by the problematic deficiency of the LBM in capturing the Knudsen
layer phenomena, present study tends to concentrate on the effective
molecular mean free path concept the main essence of which is to
compensate the incapability of this mesoscopic method in dealing
with the momentum and energy transport within the above mentioned
kinetic boundary layer. The results show qualitative and quantitative
accuracy comparable to the solutions of the linearized Boltzmann
equation or the DSMC data for the Knudsen numbers of O (1) .
Abstract: This study was aimed to study the probability about
the production of fiberboard made of durian rind through latex with
phenolic resin as binding agent. The durian rind underwent the
boiling process with NaOH [7], [8] and then the fiber from durian
rind was formed into fiberboard through heat press. This means that
durian rind could be used as replacement for plywood in plywood
industry by using durian fiber as composite material with adhesive
substance. This research would study the probability about the
production of fiberboard made of durian rind through latex with
phenolic resin as binding agent. At first, durian rind was split,
exposed to light, boiled and steamed in order to gain durian fiber.
Then, fiberboard was tested with the density of 600 Kg/m3 and 800
Kg/m3. in order to find a suitable ratio of durian fiber and latex.
Afterwards, mechanical properties were tested according to the
standards of ASTM and JIS A5905-1994. After the suitable ratio was
known, the test results would be compared with medium density
fiberboard (MDF) and other related research studies. According to
the results, fiberboard made of durian rind through latex with
phenolic resin at the density of 800 Kg/m3 at ratio of 1:1, the
moisture was measured to be 5.05% with specific gravity (ASTM D
2395-07a) of 0.81, density (JIS A 5905-1994) of 0.88 g/m3, tensile
strength, hardness (ASTM D2240), flexibility or elongation at break
yielded similar values as the ones by medium density fiberboard
(MDF).
Abstract: Phase transformation temperature is one of the most important parameters for the shape memory alloys (SMAs). The most popular method to determine these phase transformation temperatures is the Differential Scanning Calorimeter (DSC), but due to the limitation of the DSC testing itself, it made it difficult for the finished product which is not in the powder form. A novel method which uses the Universal Testing Machine has been conducted to determine the phase transformation temperatures. The Flexinol wire was applied with force and maintained throughout the experiment and at the same time it was heated up slowly until a temperature of approximately 1000C with direct current. The direct current was then slowly decreased to cool down the temperature of the Flexinol wire. All the phase transformation temperatures for Flexinol wire were obtained. The austenite start at 52.540C and austenite finish at 60.900C, while martensite start at 44.780C and martensite finish at 32.840C.
Abstract: In this study, structural, mechanical, thermal and
electrical properties of poly (lactic acid) (PLA) nanocomposites with
low-loaded (0-1.5 wt%) untreated, heat and nitric acid treated multiwalled
carbon nanotubes (MWCNTs) were studied. Among the
composites, untreated 0.5 wt % MWCNTs and acid-treated 1.0 wt%
MWCNTs reinforced PLA show the tensile strength and modulus
values higher than the others. These two samples along with pure
PLA exhibit the stable orthorhombic α-form, whilst other samples
reveal the less stable orthorhombic β-form, as demonstrated by X-ray
diffraction study. Differential scanning calorimetry reveals the
evolution of the mentioned different phases by controlled cooling and
discloses an enhancement of PLA crystallization by nanotubes
incorporation. Thermogravimetric analysis shows that the MWCNTs
loaded sample degraded faster than PLA. Surface resistivity of the
nanocomposites is found to be dropped drastically by a factor of 1013
with a low loading of MWCNTs (1.5 wt%).
Abstract: Two-dimensional heat conduction within a composed solid material with a constant internal heat generation has been investigated numerically in a sector of the rotor a generator. The heat transfer between two adjacent materials is assumed to be purely conduction. Boundary conditions are assumed to be forced convection on the fluid side and adiabatic on symmetry lines. The control volume method is applied for the diffusion energy equation. Physical coordinates are transformed to the general curvilinear coordinates. Then by using a line-by-line method, the temperature distribution in a sector of the rotor has been determined. Finally, the results are normalized and the effect of cooling fluid on the maximum temperature of insulation is investigated.
Abstract: Oxide scale thickness measurements are used in assessing the life of different components operating at high temperature environment. Such measurements provide an approximation for the temperature inside components such as reheater and superheater tubes. A number of failures were encountered in one of the boilers in one of Kuwaiti power plants. These failure were mainly in the first row of the primary super heater tubes, therefore, the specialized engineer decide to replace them during the annual shutdown. As a tool for failure analysis, oxide scale thickness measurement were used to investigate the temperature distribution in these tubes. In this paper, the oxide scale thickness of these tubes were measured and used for analysis. The measurements provide an illustration of the distribution of heat transfer of the primary superheater tubes in the boiler system. Remarks and analysis about the design of the boiler are also provided.
Abstract: Waterlogging reduces shoot and root growth and final
yield of wheat. Waterlogged sites have a combination of low slope,
high rainfall, heavy texture and low permeability. This study was
aimed the importance of waterlogging on root growth and wheat
yield. In order to study the effects of different waterlogging duration
(0, 10, 20 and 30 days) at growth stages (1-leaf stage, tillering stage
and stem elongation stage) on root growth of wheat cultivars
(Chamran, Vee/Nac and Yavaroos), one pot experiment was carried
out. The experiment was a factorial according to a RCBD with three
replications. Results showed that root dry weight and total root
length in the anthesis and grain ripening stages and biological and
grain yields were significantly different between cultivars, growth
stages and waterlogging durations. Vee/Nac was found superior with
respect to other cultivars. Susceptibility to waterlogging at different
growth stages for cultivars was 1-leaf stage > tillering stage > stem
elongation stage. Under waterlogging treatments, grain and
biological yields, were decreased 44.5 and 39.8%, respectively. Root
length and root dry weight were reduced 55.1 and 45.2%,
respectively, too. In this experiment, decrease at root growth because
of waterlogging reduced grain and biological yields. Based on the
results, even short period (10 days) of waterlogging had
unrecoverable effects on the root growth and grain yield of wheat.
Abstract: The aim of this paper is to investigate twodimensional unsteady flow of a viscous incompressible fluid about stagnation point on permeable stretching sheet in presence of time dependent free stream velocity. Fluid is considered in the influence of transverse magnetic field in the presence of radiation effect. Rosseland approximation is use to model the radiative heat transfer. Using time-dependent stream function, partial differential equations corresponding to the momentum and energy equations are converted into non-linear ordinary differential equations. Numerical solutions of these equations are obtained by using Runge-Kutta Fehlberg method with the help of Newton-Raphson shooting technique. In the present work the effect of unsteadiness parameter, magnetic field parameter, radiation parameter, stretching parameter and the Prandtl number on flow and heat transfer characteristics have been discussed. Skin-friction coefficient and Nusselt number at the sheet are computed and discussed. The results reported in the paper are in good agreement with published work in literature by other researchers.
Abstract: The forced convection heat transfer in high porosity metal-foam filled tube heat exchangers are studied in this paper. The Brinkman Darcy momentum model and two energy equations for both solid and fluid phases in porous media are employed .The study shows that using metal-foams can significantly improve the heat transfer in heat exchangers.
Abstract: A numerical study on the influence of forward-facing
cavity length upon forward-facing cavity and opposing jet combined
thermal protection system (TPS) cooling efficiency under hypersonic
flow is conducted, by means of which the flow field parameters, heat
flux distribution along the outer body surface are obtained. The
numerical simulation results are validated by experiments and the
cooling effect of the combined TPS with different cavity length is
analyzed. The numerical results show that the combined configuration
dose well in cooling the nose of the hypersonic vehicle. The deeper the
cavity is, the weaker the heat flux is. The recirculation region plays a
key role for the reduction of the aerodynamic heating.
Abstract: The present study is concerned with the free
convective two dimensional flow and heat transfer, within the
framework of Boussinesq approximation, in anisotropic fluid filled
porous rectangular enclosure subjected to end-to-end temperature
difference have been investigated using Lattice Boltzmann method
fornon-Darcy flow model. Effects of the moving lid direction (top,
bottom, left, and right wall moving in the negative and positive x&ydirections),
number of moving walls (one or two opposite walls), the
sliding wall velocity, and four different constant temperatures
opposite walls cases (two surfaces are being insulated and the
twoother surfaces areimposed to be at constant hot and cold
temperature)have been conducted. The results obtained are discussed
in terms of the Nusselt number, vectors, contours, and isotherms.
Abstract: In this research, a 2-D computational analysis of
steady state free convection in a rectangular enclosure filled with an
electrically conducting fluid under Effect of Magnetic Field has been
performed. The governing equations (mass, momentum, and energy)
are formulated and solved by a finite volume method (FVM)
subjected to different boundary conditions. A parametric study has
been conducted to consider the influence of Grashof number (Gr),
Prantdl number (Pr) and the orientation of magnetic field on the flow
and heat transfer characteristics. It is observed that Nusselt number
(Nu) and heat flux will increase with increasing Grashof and Prandtl
numbers and decreasing the slope of the orientation of magnetic field.
Abstract: A dead leg is a typical subsea production system
component. CFD is required to model heat transfer within the dead
leg. Unfortunately its solution is time demanding and thus not
suitable for fast prediction or repeated simulations. Therefore there is
a need to create a thermal FEA model, mimicking the heat flows and
temperatures seen in CFD cool down simulations.
This paper describes the conventional way of tuning and a new
automated way using parametric model order reduction (PMOR)
together with an optimization algorithm. The tuned FE analyses
replicate the steady state CFD parameters within a maximum error in
heat flow of 6 % and 3 % using manual and PMOR method
respectively. During cool down, the relative error of the tuned FEA
models with respect to temperature is below 5% comparing to the
CFD. In addition, the PMOR method obtained the correct FEA setup
five times faster than the manually tuned FEA.