Abstract: In this work, numerical simulations were carried out using a specific CFD code in order to study the performance of an innovative Scraped Surface Heat Exchanger (SSHE) with helical ribbons for Bingham fluids (threshold fluids). The resolution of three-dimensional form of the conservation equations (continuity, momentum and energy equations) was carried out basing on the finite volume method (FVM). After studying the effect of dimensionless numbers (axial Reynolds, rotational Reynolds and Oldroyd numbers) on the hydrodynamic and thermal behaviors within SSHE, a parametric study was developed, by varying the width of the helical ribbon, the clearance between the stator wall and the tip of the ribbon and the number of turns of the helical ribbon, in order to improve the heat transfer inside the exchanger. The effect of these geometrical numbers on the hydrodynamic and thermal behaviors was discussed.
Abstract: The objectives of this paper are to investigate effects of dimensionless numbers on thermal performance of the vertical closed-loop pulsating heat pipe (VCLPHP) and to establish a correlation to predict the thermal performance of the VCLPHP. The CLPHPs were made of long copper capillary tubes with inner diameters of 1.50, 1.78, and 2.16mm and bent into 26 turns. Then, both ends were connected together to form a loop. The evaporator, adiabatic, and condenser sections length were equal to 50 and 150 mm. R123, R141b, acetone, ethanol, and water were chosen as variable working fluids with constant filling ratio of 50% by total volume. Inlet temperature of heating medium and adiabatic section temperature was constantly controlled at 80 and 50oC, respectively. Thermal performance was represented in a term of Kutateladze number (Ku). It can be concluded that when Prandtl number of liquid working fluid (Prl), and Karman number (Ka) increases, thermal performance increases. On contrary, when Bond number (Bo), Jacob number (Ja), and Aspect ratio (Le/Di) increases, thermal performance decreases. Moreover, the correlation to predict more precise thermal performance has been successfully established by analyzing on all dimensionless numbers that have effect on the thermal performance of the VCLPHP.
Abstract: How to simulate experimentally the air flow and heat
transfer under microgravity on the ground is important, which has not
been completely solved so far. Influence of gravity on air natural
convection results in convection heat transfer on ground difference
from that on orbit. In order to obtain air temperature and velocity
deviations of manned spacecraft during terrestrial thermal test,
dimensionless number analysis and numerical simulation analysis are
performed. The calculated temperature distribution and velocity
distribution of the horizontal test cases are compared to the vertical
cases. The results show that the influence of gravity is neglected for
facility drawer racks and more obvious for vertical cabins.
Abstract: Studies on gas solid mass transfer using Supercritical fluid CO2 (SC-CO2) in a packed bed of palm kernels was investigated at operating conditions of temperature 50 °C and 70 °C and pressures ranges from 27.6 MPa, 34.5 MPa, 41.4 MPa and 48.3 MPa. The development of mass transfer models requires knowledge of three properties: the diffusion coefficient of the solute, the viscosity and density of the Supercritical fluids (SCF). Matematical model with respect to the dimensionless number of Sherwood (Sh), Schmidt (Sc) and Reynolds (Re) was developed. It was found that the model developed was found to be in good agreement with the experimental data within the system studied.
Abstract: Radial flow reactor was focused for large scale
methanol synthesis and in which the heat transfer type was cross-flow.
The effects of operating conditions including the reactor inlet air
temperature, the heating pipe temperature and the air flow rate on the
cross-flow heat transfer was investigated and the results showed that
the temperature profile of the area in front of the heating pipe was
slightly affected by all the operating conditions. The main area whose
temperature profile was influenced was the area behind the heating
pipe. The heat transfer direction according to the air flow directions. In
order to provide the basis for radial flow reactor design calculation, the
dimensionless number group method was used for data fitting of the
bed effective thermal conductivity and the wall heat transfer
coefficient which was calculated by the mathematical model with the
product of Reynolds number and Prandtl number. The comparison of
experimental data and calculated value showed that the calculated
value fit the experimental data very well and the formulas could be
used for reactor designing calculation.