Abstract: This paper presents an evaluation for a wavelet-based
digital watermarking technique used in estimating the quality of
video sequences transmitted over Additive White Gaussian Noise
(AWGN) channel in terms of a classical objective metric, such as
Peak Signal-to-Noise Ratio (PSNR) without the need of the original
video. In this method, a watermark is embedded into the Discrete
Wavelet Transform (DWT) domain of the original video frames
using a quantization method. The degradation of the extracted
watermark can be used to estimate the video quality in terms of
PSNR with good accuracy. We calculated PSNR for video frames
contaminated with AWGN and compared the values with those
estimated using the Watermarking-DWT based approach. It is found
that the calculated and estimated quality measures of the video
frames are highly correlated, suggesting that this method can provide
a good quality measure for video frames transmitted over AWGN
channel without the need of the original video.
Abstract: A shaft-type activated sludge reactor has been
developed in order to study the feasibility of high-rate wastewater
treatment. The reactor having volume of about 14.5 L was operated
with the acclimated mixed activated sludge under batch and
continuous mode using a synthetic wastewater as feed. The batch
study was performed with varying chemical oxygen demand (COD)
concentrations of 1000–3500 mg·L-1 for a batch period up to 9 h. The
kinetic coefficients: Ks, k, Y and kd were obtained as 2040.2 mg·L-1
and 0.105 h-1, 0.878 and 0.0025 h-1 respectively from Monod-s
approach. The continuous study showed a stable and steady state
operation for a hydraulic retention time (HRT) of 8 h and influent
COD of about 1000 mg·L-1. A maximum COD removal efficiency of
about 80% was attained at a COD loading rate and food-tomicroorganism
(F/M) ratio (COD basis) of 3.42 kg·m-3d-1 and 1.0
kg·kg-1d-1 respectively under a HRT of 8 h. The reactor was also
found to handle COD loading rate and F/M ratio of 10.8 kg·m-3d-1
and 2.20 kg·kg-1d-1 respectively showing a COD removal efficiency
of about 46%.
Abstract: This work addresses the problem of optimizing
completely batch water-using network with multiple contaminants
where the flow change caused by mass transfer is taken into
consideration for the first time. A mathematical technique for
optimizing water-using network is proposed based on
source-tank-sink superstructure. The task is to obtain the freshwater
usage, recycle assignments among water-using units, wastewater
discharge and a steady water-using network configuration by
following steps. Firstly, operating sequences of water-using units are
determined by time constraints. Next, superstructure is simplified by
eliminating the reuse and recycle from water-using units with
maximum concentration of key contaminants. Then, the non-linear
programming model is solved by GAMS (General Algebra Model
System) for minimum freshwater usage, maximum water recycle and
minimum wastewater discharge. Finally, numbers of operating periods
are calculated to acquire the steady network configuration. A case
study is solved to illustrate the applicability of the proposed approach.
Abstract: Thermally insulating ceramic coatings also known as
thermal barrier coatings (TBCs) have been essential technologies to
improve the performance and efficiency of advanced gas turbines in
service at extremely high temperatures. The damage mechanisms of
air-plasma sprayed YSZ thermal barrier coatings (TBC) with various
microstructures were studied by microscopic techniques after thermal
cycling. The typical degradation of plasma TBCs that occurs during
cyclic furnace testing of an YSZ and alumina coating on a Titanium
alloy are analyzed. During the present investigation the effects of
topcoat thickness, bond coat oxidation, thermal cycle lengths and test
temperature are investigated using thermal cycling. These results
were correlated with stresses measured by a spectroscopic technique
in order to understand specific damage mechanism. The failure
mechanism of former bond coats was found to involve fracture
initiation at the thermally grown oxide (TGO) interface and at the
TGO bond coat interface. The failure mechanism of the YZ was
found to involve combination of fracture along the interface between
TGO and bond coat.
Abstract: Buildings are one of the valuable assets to provide
people with shelters for work, leisure and rest. After years of
attacks by weather, buildings will deteriorate which need proper
maintenance in order to fulfill the requirements and satisfaction of
the users. Poorly managed buildings not just give a negative image
to the city itself, but also pose potential risk hazards to the health
and safety of the general public. As a result, the management of
maintenance projects has played an important role in cities like
Hong Kong where the problem of urban decay has drawn much
attention. However, most research has focused on managing new
construction, and little research effort has been put on maintenance
projects. Given the short duration and more diversified nature of
work, repair and maintenance works are found to be more difficult
to monitor and regulate when compared with new works. Project
participants may face with problems in running maintenance
projects which should be investigated so that proper strategies can
be established. This paper aims to provide a thorough analysis on
the problems of running maintenance projects. A review of
literature on the characteristics of building maintenance projects
was firstly conducted, which forms a solid basis for the empirical
study. Results on the problems and difficulties of running
maintenance projects from the viewpoints of industry practitioners
will also be delivered with a view to formulating effective
strategies for managing maintenance projects successfully.
Abstract: Surgical site infections (SSIs) are the most common
nosocomial infection in surgical patients resulting in significant
increases in postoperative morbidity and mortality. The commonly
causative bacteria developed resistance to virtually all antibiotics
available. The aim of this study was to isolation and identification the
most common bacteria that cause SSIs in Medical Research Institute,
and to compare their sensitivity to selected group of antibiotics and
natural products (garlic, oregano, olive, and Nigella sativa oils). The
isolated pathogens collected from infected surgical wounds were
identified, and their sensitivities to the antibiotics commonly
available for clinical use, and also to the different concentrations of
the used natural products were investigated. The results indicate to
the potential therapeutic effect of the tested natural products in
treatment of surgical wound infections.
Abstract: Each year many people are reported missing in most of the countries in the world owing to various reasons. Arrangements have to be made to find these people after some time. So the investigating agencies are compelled to make out these people by using manpower. But in many cases, the investigations carried out to find out an absconding for a long time may not be successful. At a time like that it may be difficult to identify these people by examining their old photographs, because their facial appearance might have changed mainly due to the natural aging process. On some occasions in forensic medicine if a dead body is found, investigations should be held to make sure that this corpse belongs to the same person disappeared some time ago. With the passage of time the face of the person might have changed and there should be a mechanism to reveal the person-s identity. In order to make this process easy, we must guess and decide as to how he will look like by now. To address this problem this paper presents a way of synthesizing a facial image with the aging effects.
Abstract: Whilst there is growing evidence that activity across
the lifespan is beneficial for improved health, there are also many
changes involved with the aging process and subsequently the
potential for reduced indices of health. The nexus between all forms
of health, physical activity and aging is complex and has raised much
interest in recent times due to the realization that a multifaceted
approached is necessary in order to counteract a growing obesity
epidemic. By investigating age based trends within a population
adherring to competitive sport at older ages, further insight might be
gleaned to assist in understanding one of many factors influencing
this relationship. This study evaluated those sport psychological
constructs of health, physical fitness, mental health states, and social
dimension factors in sport that were associated with factors to
participate in sport and physical activity based on responses from the
2009 World Masters Games in Sydney. The sample consisted of
7846 athletes who competed at the games and who completed a 56
item sports participation survey using a 7-point Likert response (1 -
not important to 7 - very important). Questions focuses on factors
thought to promote participation, such as weight control, living
longer, improving mental health (self-esteem, mood states),
improving physical health and factors related to the athlete-s
competitive perspective. The most significant factors related to
participation with this cohort of masters athletes were the socializing
environment of sport, getting physically fit and improving
competitive personal best performances. Strategies to increase
participation in masters sport should focus on these factors as other
factors such as weight loss, improving mental health and living
longer were not identified as important determinates of sports
participation at the World Masters level.
Abstract: The aim of the study was to determine how different
ripening processes (traditional vs. industrial) influenced the
proteolysis in traditional Serbian dry-fermented sausage Petrovská
klobása. The obtained results indicated more intensive pH decline
(0.7 units after 9 days) in industrially ripened products (I), what had a
positive impact on drying process and proteolytic changes in these
samples. Thus, moisture content in I sausages was lower at each
sampling time, amounting 24.7% at the end of production period
(90 days). Likewise, the process of proteolysis was more pronounced
in I samples, resulting in higher contents of non-protein nitrogen
(NPN) and free amino acids nitrogen (FAAN), as well as in faster
and more intensive degradation of myosin (≈220 kDa), actin (≈45
kDa) and other polypeptides during processing. Consequently, the
appearance and accumulation of several protein fragments were
registered.
Abstract: Today air-core coils (ACC) are a viable alternative to
ferrite-core coils in a range of applications due to their low induction
effect. An analytical study was carried out and the results were used as
a guide to understand the relationship between the magnet-coil
distance and the resulting attractive magnetic force. Four different
ACC models were fabricated for experimental study. The variation in
the models included the dimensions, the number of coil turns and the
current supply to the coil. Comparison between the analytical and
experimental results for all the models shows an average discrepancy
of less than 10%. An optimized ACC design was selected for the
scanner which can provide maximum magnetic force.
Abstract: EPC Class-1 Generation-2 UHF tags, one of Radio
frequency identification or RFID tag types, is expected that most
companies are planning to use it in the supply chain in the short term
and in consumer packaging in the long term due to its inexpensive
cost. Because of the very cost, however, its resources are extremely
scarce and it is hard to have any valuable security algorithms in it. It
causes security vulnerabilities, in particular cloning the tags for
counterfeits. In this paper, we propose a product authentication
solution for anti-counterfeiting at application level in the supply chain
and mobile RFID environment. It aims to become aware of
distribution of spurious products with fake RFID tags and to provide a
product authentication service to general consumers with mobile
RFID devices like mobile phone or PDA which has a mobile RFID
reader. We will discuss anti-counterfeiting mechanisms which are
required to our proposed solution and address requirements that the
mechanisms should have.
Abstract: Dynamic bandwidth allocation in EPONs can be
generally separated into inter-ONU scheduling and intra-ONU scheduling. In our previous work, the active intra-ONU scheduling
(AS) utilizes multiple queue reports (QRs) in each report message to cooperate with the inter-ONU scheduling and makes the granted
bandwidth fully utilized without leaving unused slot remainder (USR).
This scheme successfully solves the USR problem originating from the
inseparability of Ethernet frame. However, without proper setting of
threshold value in AS, the number of QRs constrained by the IEEE
802.3ah standard is not enough, especially in the unbalanced traffic
environment. This limitation may be solved by enlarging the threshold
value. The large threshold implies the large gap between the adjacent QRs, thus resulting in the large difference between the best granted bandwidth and the real granted bandwidth. In this paper, we integrate
AS with a cooperative prediction mechanism and distribute multiple
QRs to reduce the penalty brought by the prediction error.
Furthermore, to improve the QoS and save the usage of queue reports,
the highest priority (EF) traffic which comes during the waiting time is
granted automatically by OLT and is not considered in the requested
bandwidth of ONU. The simulation results show that the proposed
scheme has better performance metrics in terms of bandwidth
utilization and average delay for different classes of packets.
Abstract: This paper presents software tools that convert the C/Cµ floating point source code for a DSP algorithm into a fixedpoint simulation model that can be used to evaluate the numericalperformance of the algorithm on several different fixed pointplatforms including microprocessors, DSPs and FPGAs. The tools use a novel system for maintaining binary point informationso that the conversion from floating point to fixed point isautomated and the resulting fixed point algorithm achieves maximum possible precision. A configurable architecture is used during the simulation phase so that the algorithm can produce a bit-exact output for several different target devices.
Abstract: The decision to recruit manpower in an organization
requires clear identification of the criteria (attributes) that distinguish
successful from unsuccessful performance. The choice of appropriate
attributes or criteria in different levels of hierarchy in an organization
is a multi-criteria decision problem and therefore multi-criteria
decision making (MCDM) techniques can be used for prioritization
of such attributes. Analytic Hierarchy Process (AHP) is one such
technique that is widely used for deciding among the complex criteria
structure in different levels. In real applications, conventional AHP
still cannot reflect the human thinking style as precise data
concerning human attributes are quite hard to be extracted. Fuzzy
logic offers a systematic base in dealing with situations, which are
ambiguous or not well defined. This study aims at defining a
methodology to improve the quality of prioritization of an
employee-s performance measurement attributes under fuzziness. To
do so, a methodology based on the Extent Fuzzy Analytic Hierarchy
Process is proposed. Within the model, four main attributes such as
Subject knowledge and achievements, Research aptitude, Personal
qualities and strengths and Management skills with their subattributes
are defined. The two approaches conventional AHP
approach and the Extent Fuzzy Analytic Hierarchy Process approach
have been compared on the same hierarchy structure and criteria set.
Abstract: By using the method of coincidence degree and constructing suitable Lyapunov functional, some sufficient conditions are established for the existence and global exponential stability of antiperiodic solutions for a kind of impulsive Cohen-Grossberg shunting inhibitory cellular neural networks (CGSICNNs) on time scales. An example is given to illustrate our results.
Abstract: Polyphenolics and sugar are the components of many
fruit juices. In this work, the performance of ultra-filtration (UF) for
separating phenolic compounds from apple juice was studied by
performing batch experiments in a membrane module with an area of
0.1 m2 and fitted with a regenerated cellulose membrane of 1 kDa
MWCO. The effects of various operating conditions: transmembrane
pressure (3, 4, 5 bar), temperature (30, 35, 40 ºC), pH (2, 3, 4, 5),
feed concentration (3, 5, 7, 10, 15 ºBrix for apple juice) and feed flow
rate (1, 1.5, 1.8 L/min) on the performance were determined.
The optimum operating conditions were: transmembrane pressure
4 bar, temperature 30 ºC, feed flow rate 1 – 1.8 L/min, pH 3 and 10
Brix (apple juice). After performing ultrafiltration under these
conditions, the concentration of polyphenolics in retentate was
increased by a factor of up to 2.7 with up to 70% recovered in the
permeate and with approx. 20% of the sugar in that stream..
Application of diafiltration (addition of water to the concentrate) can
regain the flux by a factor of 1.5, which has been decreased due to
fouling. The material balance performed on the process has shown
the amount of deposits on the membrane and the extent of fouling in
the system. In conclusion, ultrafiltration has been demonstrated as a
potential technology to separate the polyphenolics and sugars from
their mixtures and can be applied to remove sugars from fruit juice.
Abstract: Contractor selection in Saudi Arabia is very important due to the large construction boom and the contractor role to get over construction risks. The need for investigating contractor selection is due to the following reasons; large number of defaulted or failed projects (18%), large number of disputes attributed to contractor during the project execution stage (almost twofold), the extension of the General Agreement on Tariffs and Trade (GATT) into construction industry, and finally the few number of researches. The selection strategy is not perfect and considered as the reason behind irresponsible contractors. As a response, this research was conducted to review the contractor selection strategies as an integral part of a long advanced research to develop a good selection model. Many techniques can be used to form a selection strategy; multi criteria for optimizing decision, prequalification to discover contractor-s responsibility, bidding process for competition, third party guarantee to enhance the selection, and fuzzy techniques for ambiguities and incomplete information.
Abstract: Three service providers in competition, try to optimize
their quality of service / content level and their service access
price. But, they have to deal with uncertainty on the consumers-
preferences. To reduce their uncertainty, they have the opportunity
to buy information and to build alliances. We determine the Shapley
value which is a fair way to allocate the grand coalition-s revenue
between the service providers. Then, we identify the values of β
(consumers- sensitivity coefficient to the quality of service / contents)
for which allocating the grand coalition-s revenue using the Shapley
value guarantees the system stability. For other values of β, we prove
that it is possible for the regulator to impose a per-period interest rate
maximizing the market coverage under equal allocation rules.
Abstract: In H.264/AVC video encoding, rate-distortion
optimization for mode selection plays a significant role to achieve
outstanding performance in compression efficiency and video quality.
However, this mode selection process also makes the encoding
process extremely complex, especially in the computation of the ratedistortion
cost function, which includes the computations of the sum
of squared difference (SSD) between the original and reconstructed
image blocks and context-based entropy coding of the block. In this
paper, a transform-domain rate-distortion optimization accelerator
based on fast SSD (FSSD) and VLC-based rate estimation algorithm
is proposed. This algorithm could significantly simplify the hardware
architecture for the rate-distortion cost computation with only
ignorable performance degradation. An efficient hardware structure
for implementing the proposed transform-domain rate-distortion
optimization accelerator is also proposed. Simulation results
demonstrated that the proposed algorithm reduces about 47% of total
encoding time with negligible degradation of coding performance.
The proposed method can be easily applied to many mobile video
application areas such as a digital camera and a DMB (Digital
Multimedia Broadcasting) phone.
Abstract: In this paper, a joint source-channel coding (JSCC) scheme for time-varying channels is presented. The proposed scheme uses hierarchical framework for both source encoder and transmission via QAM modulation. Hierarchical joint source channel codes with hierarchical QAM constellations are designed to track the channel variations which yields to a higher throughput by adapting certain parameters of the receiver to the channel variation. We consider the problem of still image transmission over time-varying channels with channel state information (CSI) available at 1) receiver only and 2) both transmitter and receiver being informed about the state of the channel. We describe an algorithm that optimizes hierarchical source codebooks by minimizing the distortion due to source quantizer and channel impairments. Simulation results, based on image representation, show that, the proposed hierarchical system outperforms the conventional schemes based on a single-modulator and channel optimized source coding.