Abstract: Annihilations, phase shifts, scattering lengths and
elastic cross sections of low energy positrons scattering from
magnesium atoms were studied using the least-squares variational
method (LSVM). The possibility of positron binding to the
magnesium atoms is investigated. A trial wave function is suggested
to represent e+-Mg elastic scattering and scattering parameters were
derived to estimate the binding energy and annihilation rates. The
trial function is taken to depend on several adjustable parameters, and
is improved iteratively by increasing the number of terms. The
present results have the same behavior as reported semi-empirical,
theoretical and experimental results. Especially, the estimated
positive scattering length supports the possibility of positronmagnesium
bound state system that was confirmed in previous
experimental and theoretical work.
Abstract: A clay soil classified as A-7-6 and CH soil according
to AASHTO and unified soil classification system respectively, was
stabilized using A-3 soil (AASHTO soil classification system). The
clay soil was replaced with 0%, 10%, 20%, to 100% A-3 soil,
compacted at both British Standard Light (BSL) and British Standard
Heavy (BSH) compaction energy levels and using Unconfined
Compressive Strength (UCS) as evaluation criteria. The Maximum
Dry Density (MDD) of the treated soils at both the BSL and BSH
compaction energy levels showed increase from 0% to 40% A-3 soil
replacement after which the values reduced to 100% replacement.
The trend of the Optimum Moisture Content (OMC) with varied A-3
soil replacement was similar to that of MDD but in a reversed order.
The OMC reduced from 0% to 40% A-3 soil replacement after which
the values increased to 100% replacement. This trend was attributed
to the observed reduction in void ratio from 0% to 40% replacement
after which the void ratio increased to 100% replacement. The
maximum UCS for the soil at varied A-3 soil replacement increased
from 272 and 770 kN/m2 for BSL and BSH compaction energy level
at 0% replacement to 295 and 795 kN/m2 for BSL and BSH
compaction energy level respectively at 10% replacement after which
the values reduced to 22 and 60 kN/m2 for BSL and BSH compaction
energy level respectively at 70% replacement. Beyond 70%
replacement, the mixtures could not be moulded for UCS test.
Abstract: Maintaining factory default battery endurance rate
over time in supporting huge amount of running applications on
energy-restricted mobile devices has created a new challenge for
mobile applications developer. While delivering customers’
unlimited expectations, developers are barely aware of efficient use
of energy from the application itself. Thus, developers need a set of
valid energy consumption indicators in assisting them to develop
energy saving applications. In this paper, we present a few software
product metrics that can be used as an indicator to measure energy
consumption of Android-based mobile applications in the early of
design stage. In particular, Trepn Profiler (Power profiling tool for
Qualcomm processor) has used to collect the data of mobile
application power consumption, and then analyzed for the 23
software metrics in this preliminary study. The results show that
McCabe cyclomatic complexity, number of parameters, nested block
depth, number of methods, weighted methods per class, number of
classes, total lines of code and method lines have direct relationship
with power consumption of mobile application.
Abstract: The growth in the demand of electrical energy is
leading to load on the Power system which increases the occurrence
of frequent oscillations in the system. The reason for the oscillations
is due to the lack of damping torque which is required to dominate
the disturbances of Power system. By using FACT devices, such as
Unified Power Flow Controller (UPFC) can control power flow,
reduce sub-synchronous resonances and increase transient stability.
Hence, UPFC is used to damp the oscillations occurred in Power
system. This research focuses on adapting the neuro fuzzy controller
for the UPFC design by connecting the infinite bus (SMIB - Single
machine Infinite Bus) to a linearized model of synchronous machine
(Heffron-Phillips) in the power system. This model gains the
capability to improve the transient stability and to damp the
oscillations of the system.
Abstract: Here, we have shown the reaction of [Cr(ArN(CH2)3NAr)2Cl2] (1) where (Ar = 2,6-Pri
2C6H3) and in presence of NaCp (2) (Cp= C5H5 = cyclopentadien), with a center
coordination η5 interaction between Cp as co-ligand and chromium
metal center, for optimization we used density functional theory
(DFT), under methods, explicitly including electrons correlations, for
the final calculations as MB3LYP (Becke) (Lee–Yang–Parr) level of
theory we used to obtain more exact results. This complex was
calculated as electronic energy for molecular system, because the
calculation accounting all electrons correlations interactions. The
optimised of [Cr(ArN(CH2)3NAr)2(η5-Cp)] (Ar = 2,6-Pri2C6H3 and Cp = C5H5) was found to be thermally stable. By using Dewar-Chatt-Duncanson model, as a basis of the molecular orbital (MO) analysis
and showed the highest occupied molecular orbital (HOMO) and
lowest occupied molecular orbital LUMO.
Abstract: Evolutionary Algorithms (EAs) have been used
widely through evolution theory to discover acceptable solutions that
corresponds to challenges such as natural resources management.
EAs are also used to solve varied problems in the real world. EAs
have been rapidly identified for its ease in handling multiple
objective problems. Reservoir operations is a vital and researchable
area which has been studied in the last few decades due to the limited
nature of water resources that is found mostly in the semi-arid
regions of the world. The state of some developing economy that
depends on electricity for overall development through hydropower
production, a renewable form of energy, is appalling due to water
scarcity. This paper presents a review of the applications of
evolutionary algorithms to reservoir operation for hydropower
production. This review includes the discussion on areas such as
genetic algorithm, differential evolution, and reservoir operation. It
also identified the research gaps discovered in these areas. The results
of this study will be an eye opener for researchers and decision
makers to think deeply of the adverse effect of water scarcity and
drought towards economic development of a nation. Hence, it
becomes imperative to identify evolutionary algorithms that can
address this issue which can hamper effective hydropower
generation.
Abstract: The energy need is growing rapidly due to the
population growth and the large new usage of power. Several works
put considerable efforts to make the electricity grid more intelligent
to reduce essentially energy consumption and provide efficiency and
reliability of power systems. The Smart Grid is a complex
architecture that covers critical devices and systems vulnerable to
significant attacks. Hence, security is a crucial factor for the success
and the wide deployment of Smart Grids. In this paper, we present
security issues of the Smart Grid architecture and we highlight open
issues that will make the Smart Grid security a challenging research
area in the future.
Abstract: In this numerical study, effects of using Al2O3-water
nanofluid on the rate of heat transfer have been investigated. Physical
model is a square enclosure with insulated top and bottom horizontal
walls, while the vertical walls are kept at different constant
temperatures. Two appropriate models are used to evaluate the
viscosity and thermal conductivity of nanofluid. The governing
stream-vorticity equations are solved using a second order central
finite difference scheme, coupled to the conservation of mass and
energy. The study has been carried out for the nanoparticle diameter
30, 60 and 90 nm and the solid volume fraction 0 to 0.04. Results are
presented by average Nusselt number and normalized Nusselt number
in different range of φ and D for mixed convection dominated
regime. It is found that different heat transfer rate is predicted when
the effect of nanoparticle diameter is taken into account.
Abstract: Fresh water is one of the resources which is getting
depleted day by day. A wise method to address this issue is by the
application of renewable energy-sun irradiation and by means of
decentralized, cheap, energetically self-sufficient, robust and simple
to operate plants, distillates can be obtained from sea, river or even
sewage. Solar desalination is a technique used to desalinate water
using solar energy. The present work deals with the comprehensive
design and simulation of solar tracking system using LabVIEW,
temperature and mass flow rate control of the solar desalination plant
using LabVIEW and also analysis of single phase inverter circuit
with LC filters for solar pumping system in MATLAB. The main
objective of this work is to improve the performance of solar
desalination system using automatic tracking system, output control
using temperature and mass flow rate control system and also to
reduce the harmonic distortion in the solar pumping system by means
of LC filters. The simulation of single phase inverter was carried out
using MATLAB and the output waveforms were analyzed.
Simulations were performed for optimum output temperature control,
which in turn controls the mass flow rate of water in the thermal
collectors. Solar tracking system was accomplished using LABVIEW
and was tested successfully. The thermal collectors are tracked in
accordance with the sun’s irradiance levels, thereby increasing the
efficiency of the thermal collectors.
Abstract: The development of composite materials and the
related design and manufacturing technologies is one of the most
important advances in the history of materials. Composites are
multifunctional materials having unprecedented mechanical and
physical properties that can be tailored to meet the requirements of a
particular application. Some composites also exhibit great resistance
to high-temperature corrosion, oxidation, and wear. Polymers are
widely used indoors and outdoors, therefore they are exposed to a
chemical environment which may include atmospheric oxygen, acidic
fumes, acidic rain, moisture heat and thermal shock, ultra-violet light,
high energy radiation, etc. Different polymers are affected differently
by these factors even though the amorphous polymers are more
sensitive. Ageing is also important and it is defined as the process of
deterioration of engineering materials resulting from the combined
effects of atmospheric radiation, heat, oxygen, water, microorganisms
and other atmospheric factors.
Abstract: Carbon Fiber Reinforced Plastics (CFRPs) are widely
used for advanced applications, in particular in aerospace, automotive
and wind energy industries. Once cured to near net shape, CFRP
parts need several finishing operations such as trimming, milling or
drilling in order to accommodate fastening hardware and meeting the
final dimensions. The present research aims to study the effect of the
cutting temperature in trimming on the mechanical strength of high
performance CFRP laminates used for aeronautics applications. The
cutting temperature is of great importance when dealing with
trimming of CFRP. Temperatures higher than the glass-transition
temperature (Tg) of the resin matrix are highly undesirable: they
cause degradation of the matrix in the trimmed edges area, which can
severely affect the mechanical performance of the entire component.
In this study, a 9.50mm diameter CVD diamond coated carbide tool
with six flutes was used to trim 24-plies CFRP laminates. A
300m/min cutting speed and 1140mm/min feed rate were used in the
experiments. The tool was heated prior to trimming using a
blowtorch, for temperatures ranging from 20°C to 300°C. The
temperature at the cutting edge was measured using embedded KType
thermocouples. Samples trimmed for different cutting
temperatures, below and above Tg, were mechanically tested using
three-points bending short-beam loading configurations. New cutting
tools as well as worn cutting tools were utilized for the experiments.
The experiments with the new tools could not prove any correlation
between the length of cut, the cutting temperature and the mechanical
performance. Thus mechanical strength was constant, regardless of
the cutting temperature. However, for worn tools, producing a cutting
temperature rising up to 450°C, thermal damage of the resin was
observed. The mechanical tests showed a reduced mean resistance in
short beam configuration, while the resistance in three point bending
decreases with increase of the cutting temperature.
Abstract: On account of the concern of the fossil fuel is
depleting and its negative effects on the environment, interest in
alternative energy sources is increasing day by day. However,
considering the importance of transportation in human life, instead of
oil and its derivatives fueled vehicles with internal combustion
engines, electric vehicles which are sensitive to the environment and
working with electrical energy has begun to develop. In this study,
simulation was carried out for providing energy management and
recovering regenerative braking in fuel cell-battery hybrid electric
vehicle. The main power supply of the vehicle is fuel cell on the other
hand not only instantaneous power is supplied by the battery but also
the energy generated due to regenerative breaking is stored in the
battery. Obtained results of the simulation is analyzed and discussed.
Abstract: Analytical formula for the optical gain based on a
simple parabolic-band by introducing theoretical expressions for the
quantized energy is presented. The model used in this treatment take
into account the effects of intraband relaxation. It is shown, as a
result, that the gain for the TE mode is larger than that for TM mode
and the presence of acceptor impurity increase the peak gain.
Abstract: This paper presents the influence of the vertical
seismic component on the non-linear dynamics analysis of three
different structures. The subject structures were analyzed and
designed according to recent codes. This paper considers three types
of buildings: 5-, 10-, and 15-story buildings. The non-linear
dynamics analysis of the structures with assuming elastic-perfectlyplastic
behavior was performed using RAM PERFORM-3D software;
the horizontal component was taken into consideration with and
without the incorporation of the corresponding vertical component.
Dynamic responses obtained for the horizontal component acting
alone were compared with those obtained from the simultaneous
application of both seismic components. The results show that the
effect of the vertical component of ground motion may increase the
axial load significantly in the interior columns and, consequently, the
stories. The plastic mechanisms would be changed. The P-Delta
effect is expected to increase. The punching base plate shear of the
columns should be considered. Moreover, the vertical component
increases the input energy when the structures exhibit inelastic
behavior and are taller.
Abstract: An integrated modeling approach was used in this study for energy planning and climate change mitigation assessment. The main objective of this study was to develop various green-house gas (GHG) mitigations scenarios in the energy demand and supply sectors for the state of Florida. The Long range energy alternative planning (LEAP) model was used in this study to examine the energy alternative and GHG emissions reduction scenarios for short and long term (2010-2050). One of the energy analysis and GHG mitigation scenarios was developed by taking into account the available renewable energy resources potential for power generation in the state of Florida. This will help to compare and analyze the GHG reduction measure against “Business As Usual” and ‘State of Florida Policy” scenarios. Two master scenarios: “Electrification” and “Energy efficiency and Lifestyle” were developed through combination of various mitigation scenarios: technological changes and energy efficiency and conservation. The results show a net reduction of the energy demand and GHG emissions by adopting these two energy scenarios compared to the business as usual.
Abstract: Growing human population has placed increased
demands on water supplies and spurred a heightened interest in
desalination infrastructure. Key elements of the economics of
desalination projects are thermal and electrical inputs. With growing
concerns over use of fossil fuels to (indirectly) supply these inputs,
coupling of desalination with nuclear power production represents a
significant opportunity. Individually, nuclear and desalination
technologies have a long history and are relatively mature. For
desalination, Reverse Osmosis (RO) has the lowest energy inputs.
However, the economically driven output quality of the water
produced using RO, which uses only electrical inputs, is lower than the
output water quality from thermal desalination plants. Therefore,
modern desalination projects consider that RO should be coupled with
thermal desalination technologies (MSF, MED, or MED-TVC) with
attendant steam inputs to permit blending to produce various qualities
of water. A large nuclear facility is well positioned to dispatch large
quantities of both electrical and thermal power. This paper considers
the supply of thermal energy to a large desalination facility to examine
heat balance impact on the nuclear steam cycle. The APR1400 nuclear
plant is selected as prototypical from both a capacity and turbine cycle
heat balance perspective to examine steam supply and the impact on
electrical output. Extraction points and quantities of steam are
considered parametrically along with various types of thermal
desalination technologies to form the basis for further evaluations of
economically optimal approaches to the interface of nuclear power
production with desalination projects. In our study, the
thermodynamic evaluation will be executed by DE-TOP, an IAEA
sponsored program. DE-TOP has capabilities to analyze power
generation systems coupled to desalination plants through various
steam extraction positions, taking into consideration the isolation loop
between the nuclear and the thermal desalination facilities (i.e., for
radiological isolation).
Abstract: The present explanatory study concerns with the
relation between Diabetes Mellitus and Food Balance in the Kingdom
of Saudi Arabia during 2005-2010, using published data. Results illustrated that Saudi citizen daily protein consumption
(DPC) during 2005-2007 (g/capita/day) is higher than the average
global consumption level of protein with 15.27%, daily fat
consumption (DFC) with 24.56% and daily energy consumption
(DEC) with 16.93% and increases than recommended level by
International Nutrition Organizations (INO) with 56% for protein,
60.49% for fat and 27.37% for energy. On the other hand, DPC per
capita in Saudi Arabia decreased during the period 2008-2010 from
88.3 to 82.36 gram/ day. Moreover, DFC per capita in Saudi Arabia
decreased during the period 2008-2010 from 3247.90 to 3176.43
Cal/capita/ day, and daily energy consumption (DEC) of Saudi
citizen increases than world consumption with 16.93%, whereas
increases with 27.37% than INO. Despite this, DPC, DFC and DEC
per capita in Saudi Arabia still higher than world mean. On the other
side, results illustrated that the number of diabetic patients in Saudi
Arabia during the same period (2005-2010). The curve of diabetic
patient’s number in Saudi Arabia during 2005-2010 is regular
ascending with increasing level ranged between 7.10% in 2005 and
12.44% in 2010. It is essential to devise Saudi National programs to educate the
public about the relation of food balances and diabetes so it could be
avoided, and provide citizens with healthy dietary balances tables.
Abstract: Objectives: To determine the nutritional status and
risk factors associated with women practicing geophagia in QwaQwa,
South Africa. Materials and Methods: An observational epidemiological study
design was adopted which included an exposed (geophagia) and nonexposed
(control) group. A food frequency questionnaire, anthropometric measurements and blood sampling were applied to
determine nutritional status of participants. Logistic regression
analysis was performed in order to identify factors that were likely to
be associated with the practice of geophagia. Results: The mean total energy intake for the geophagia group (G)
and control group (C) were 10324.31 ± 2755.00 kJ and 10763.94 ±
2556.30 kJ respectively. Both groups fell within the overweight
category according to the mean Body Mass Index (BMI) of each
group (G= 25.59 kg/m2; C= 25.14 kg/m2). The mean serum iron
levels of the geophagia group (6.929 μmol/l) were significantly lower
than that of the control group (13.75 μmol/l) (p = 0.000). Serum
transferrin (G=3.23g/l; C=2.7054g/l) and serum transferrin saturation
(G=8.05%; C=18.74%) levels also differed significantly between
groups (p=0.00). Factors that were associated with the practice of
geophagia included haemoglobin (Odds ratio (OR):14.50), serumiron
(OR: 9.80), serum-ferritin (OR: 3.75), serum-transferrin (OR:
6.92) and transferrin saturation (OR: 14.50). A significant negative
association (p=0.014) was found between women who were wageearners
and those who were not wage-earners and the practice of
geophagia (OR: 0.143; CI: 0.027; 0.755). These findings seem to
indicate that a permanent income may decrease the likelihood of
practising geophagia. Key Findings: Geophagia was confirmed to be a risk factor for
iron deficiency in this community. The significantly strong
association between geophagia and iron deficiency emphasizes the
importance of identifying the practice of geophagia in women,
especially during their child bearing years.
Abstract: Lyophilization, also called freeze-drying, is an
important dehydration technique mainly used for pharmaceuticals.
Food industry also uses lyophilization when it is important to retain
most of the nutritional quality, taste, shape and size of dried products
and to extend their shelf life. Vacuum-Induced during freezing cycle
(VI) has been used in order to control ice nucleation and,
consequently, to reduce the time of primary drying cycle of
pharmaceuticals preserving quality properties of the final product.
This procedure has not been applied in freeze drying of foods. The
present work aims to investigate the effect of VI on the lyophilization
drying time, final moisture content, density and reconstitutional
properties of mango (Mangifera indica L.) slices (MS) and mango
pulp-maltodextrin dispersions (MPM) (30% concentration of total
solids). Control samples were run at each freezing rate without using
induced vacuum. The lyophilization endpoint was the same for all
treatments (constant difference between capacitance and Pirani
vacuum gauges). From the experimental results it can be concluded
that at the high freezing rate (0.4°C/min) reduced the overall process
time up to 30% comparing process time required for the control and
VI of the lower freeze rate (0.1°C/min) without affecting the quality
characteristics of the dried product, which yields a reduction in costs
and energy consumption for MS and MPM freeze drying. Controls
and samples treated with VI at freezing rate of 0.4°C/min in MS
showed similar results in moisture and density parameters.
Furthermore, results from MPM dispersion showed favorable values
when VI was applied because dried product with low moisture
content and low density was obtained at shorter process time
compared with the control. There were not found significant
differences between reconstitutional properties (rehydration for MS
and solubility for MPM) of freeze dried mango resulting from
controls, and VI treatments.
Abstract: An analytical 4-DOF nonlinear model of a de Laval
rotor-stator system based on Energy Principles has been used
theoretically and experimentally to investigate fault symptoms in a
rotating system. The faults, namely rotor-stator-rub, crack and
unbalance are modeled as excitations on the rotor shaft. Mayes
steering function is used to simulate the breathing behaviour of the
crack. The fault analysis technique is based on waveform signal,
orbits and Fast Fourier Transform (FFT) derived from simulated and
real measured signals. Simulated and experimental results manifest
considerable mutual resemblance of elliptic-shaped orbits and FFT
for a same range of test data.