Abstract: Nonlinear evolution of broadband ultrasonic pulses
passed through the rock specimens is studied using the apparatus
“GEOSCAN-02M”. Ultrasonic pulses are excited by the pulses of Qswitched
Nd:YAG laser with the time duration of 10 ns and with the
energy of 260 mJ. This energy can be reduced to 20 mJ by some light
filters. The laser beam radius did not exceed 5 mm. As a result of the
absorption of the laser pulse in the special material – the optoacoustic
generator–the pulses of longitudinal ultrasonic waves are excited with
the time duration of 100 ns and with the maximum pressure
amplitude of 10 MPa. The immersion technique is used to measure
the parameters of these ultrasonic pulses passed through a specimen,
the immersion liquid is distilled water. The reference pulse passed
through the cell with water has the compression and the rarefaction
phases. The amplitude of the rarefaction phase is five times lower
than that of the compression phase. The spectral range of the
reference pulse reaches 10 MHz. The cubic-shaped specimens of the
Karelian gabbro are studied with the rib length 3 cm. The ultimate
strength of the specimens by the uniaxial compression is (300±10)
MPa. As the reference pulse passes through the area of the specimen
without cracks the compression phase decreases and the rarefaction
one increases due to diffraction and scattering of ultrasound, so the
ratio of these phases becomes 2.3:1. After preloading some horizontal
cracks appear in the specimens. Their location is found by one-sided
scanning of the specimen using the backward mode detection of the
ultrasonic pulses reflected from the structure defects. Using the
computer processing of these signals the images are obtained of the
cross-sections of the specimens with cracks. By the increase of the
reference pulse amplitude from 0.1 MPa to 5 MPa the nonlinear
transformation of the ultrasonic pulse passed through the specimen
with horizontal cracks results in the decrease by 2.5 times of the
amplitude of the rarefaction phase and in the increase of its duration
by 2.1 times. By the increase of the reference pulse amplitude from 5
MPa to 10 MPa the time splitting of the phases is observed for the
bipolar pulse passed through the specimen. The compression and
rarefaction phases propagate with different velocities. These features
of the powerful broadband ultrasonic pulses passed through the rock
specimens can be described by the hysteresis model of Preisach-
Mayergoyz and can be used for the location of cracks in the optically
opaque materials.
Abstract: Ocean current is always available around the
surrounding of SHELL Sabah Water Platform and data are collected
every 10 minutes, 24 hours a day, for a period of 365 days. Due to
low current speed, conventional hydrokinetic power generation is not
feasible, thus leading to the study of low current enabled vortex
induced vibration power generation application. In this case, the
design of a vortex induced vibration application is studied to obtain
an optimum design for the VIV oscillator. Power output is then
determined to study the feasibility of the VIV application in low
current condition.
Abstract: Radiative heat transfer in participating medium was
carried out using the finite volume method. The radiative transfer
equations are formulated for absorbing and anisotropically scattering
and emitting medium. The solution strategy is discussed and the
conditions for computational stability are conferred. The equations
have been solved for transient radiative medium and transient
radiation incorporated with transient conduction. Results have been
obtained for irradiation and corresponding heat fluxes for both the
cases. The solutions can be used to conclude incident energy and
surface heat flux. Transient solutions were obtained for a slab of heat
conducting in slab and by thermal radiation. The effect of heat
conduction during the transient phase is to partially equalize the
internal temperature distribution. The solution procedure provides
accurate temperature distributions in these regions. A finite volume
procedure with variable space and time increments is used to solve
the transient radiation equation. The medium in the enclosure
absorbs, emits, and anisotropically scatters radiative energy. The
incident radiations and the radiative heat fluxes are presented in
graphical forms. The phase function anisotropy plays a significant
role in the radiation heat transfer when the boundary condition is
non-symmetric.
Abstract: Piezoelectric actuator is treated as RC load when it is
modeled electrically. For some piezoelectric actuator applications,
arbitrary voltage is required to actuate. Especially for unidirectional
arbitrary voltage driving like as sine wave, some special inverter with
circuit that can charge and discharge the capacitive energy can be
used. In this case, the difference between power supply level and the
object voltage level for RC load is varied. Because the control gain is
constant, the controlled output is not uniform according to the voltage
difference. In this paper, for charge and discharge circuit for
unidirectional arbitrary voltage driving for piezoelectric actuator, the
controller gain is controlled according to the voltage difference. With
the proposed simple idea, the load voltage can have controlled
smoothly although the voltage difference is varied. The
appropriateness is proved from the simulation of the proposed circuit.
Abstract: Different countries have introduced different schemes
and policies to counter global warming. The rationale behind the
proposed policies and the potential barriers to successful
implementation of the policies adopted by the countries were
analyzed and estimated based on different models. It is argued that
these models enhance the transparency and provide a better
understanding to the policy makers. However, these models are
underpinned with several structural and baseline assumptions. These
assumptions, modeling features and future prediction of emission
reductions and other implication such as cost and benefits of a
transition to a low-carbon economy and its economy wide impacts
were discussed. On the other hand, there are potential barriers in the
form political, financial, and cultural and many others that pose a
threat to the mitigation options.
Abstract: The ventilated façade has great advantages when
compared to traditional façades as it reduces the air conditioning
thermal loads due to the stack effect induced by solar radiation in the
air chamber. Optimizing energy consumption by using a ventilated
façade can be used not only in newly built buildings but also it can be
implemented in existing buildings, opening the field of
implementation to energy building retrofitting works. In this sense, the following three prototypes of façade where
designed, built and further analyzed in this research: non-ventilated
façade (NVF); slightly ventilated façade (SLVF) and strongly
ventilated façade (STVF). The construction characteristics of the
three facades are based on the Spanish regulation of building
construction “Technical Building Code”. The façades have been
monitored by type-k thermocouples in a representative day of the
summer season in Madrid (Spain). Moreover, an analysis of variance
(ANOVA) with repeated measures, studying the thermal lag in the
ventilated and no-ventilated façades has been designed. Results show that STVF façade presents higher levels of thermal
inertia as the thermal lag reduces up to 17% (daily mean) compared
to the non-ventilated façade. In addition, the statistical analysis
proves that an increase of the ventilation holes size in STVF façades
can improve the thermal lag significantly (p >0.05) when compared
to the SLVF façade.
Abstract: Home Energy Management System (HEMS), which makes the residential consumers, contribute to the demand response is attracting attention in recent years. An aim of HEMS is to minimize their electricity cost by controlling the use of their appliances according to electricity price. The use of appliances in HEMS may be affected by some conditions such as external temperature and electricity price. Therefore, the user’s usage pattern of appliances should be modeled according to the external conditions, and the resultant usage pattern is related to the user’s comfortability on use of each appliances. This paper proposes a methodology to model the usage pattern based on the historical data with the copula function. Through copula function, the usage range of each appliance can be obtained and is able to satisfy the appropriate user’s comfort according to the external conditions for next day. Within the usage range, an optimal scheduling for appliances would be conducted so as to minimize an electricity cost with considering user’s comfort. Among the home appliance, electric heater (EH) is a representative appliance, which is affected by the external temperature. In this paper, an optimal scheduling algorithm for an electric heater (EH) is addressed based on the method of branch and bound. As a result, scenarios for the EH usage are obtained according to user’s comfort levels and then the residential consumer would select the best scenario. The case study shows the effects of the proposed algorithm compared with the traditional operation of the EH, and it represents impacts of the comfort level on the scheduling result.
Abstract: Biomass treatment through densification is very suitable and helpful technology before its effective energy recovery. Densification process of biomass is significantly influenced by various technological and material variables, which are ultimately reflected on the final solid biofuels quality. The paper deals with the experimental research of the relationship between technological and material variables during densification of fast-growing trees, roundly fast-growing willows. The main goal of presented experimental research is to determine the relationship between compression pressure and raw material particle size from a final briquettes density point of view. Experimental research was realized by single-axis densification. The impact of particle size with interaction of compression pressure and stabilization time on the quality properties of briquettes was determined. These variables interaction affects the final solid biofuels (briquettes) quality. From briquettes production point of view and from densification machines constructions point of view is very important to know about mutual interaction of these variables on final briquettes quality. The experimental findings presented here are showing the importance of mentioned variables during the densification process.
Abstract: This paper discusses micrometeorological aspects of the urban climate in three cities in Western São Paulo State: Presidente Prudente, Assis and Iepê. Particular attention is paid to the method used to estimate the components of the energy balance at the surface. Estimates of convective fluxes showed that the Bowen ratio was an indicator of the local climate and that its magnitude varied between 0.3 and 0.7. Maximum values for the Bowen ratio occurred earlier in Iepê (11:00 am) than in Presidente Prudente (4:00 pm). The results indicate that the Bowen ratio is modulated by the radiation balance at the surface and by different clusters of vegetation.
Abstract: Temperature effect on the performance of a photovoltaic module is one of the main concerns that face this renewable energy, especially in hot arid region, e.g. United Arab Emirates. Overheating of the PV modules reduces the open circuit voltage and the efficiency of the modules dramatically. In this work, water-cooling is developed to enhance the performance of PV modules. Different scenarios are tested under UAE weather conditions: front, back and double cooling. A spraying system is used for the front cooling whether a direct contact water system is used for the back cooling. The experimental results are compared to non-cooling module and the performance of the PV module is determined for different situations. The experimental results show that the front cooling is more effective than the back cooling and may decrease the temperature of the PV module significantly.
Abstract: The seriously damaged structures during earthquakes
show the need and importance of design of reinforced concrete
structures with high ductility. Reinforced concrete beam-column
joints have an important function in all structures. Under seismic
excitation, the beam column joint region is subjected to horizontal
and vertical shear forces whose magnitude is many times higher than
the adjacent beam and column. Strength and ductility of structures
depends mainly on proper detailing of the reinforcement in beamcolumn
joints and the old structures were found ductility deficient.
DSP materials are obtained by using high quantities of super
plasticizers and high volumes of micro silica. In the case of High
Performance Densified Small Particle Concrete (HPDSPC), since
concrete is dense even at the micro-structure level, tensile strain
would be much higher than that of the conventional SFRC, SIFCON
& SIMCON. This in turn will improve cracking behaviour, ductility
and energy absorption capacity of composites in addition to
durability. The fine fibers used in our mix are 0.3mm diameter and 10
mm which can be easily placed with high percentage. These fibers
easily transfer stresses and act as a composite concrete unit to take up
extremely high loads with high compressive strength. HPDSPC
placed in the beam column joints helps in safety of human life due to
prolonged failure.
Abstract: The first laboratory synthesis of hard materials such as
diamond proceeded to attack of developing materials with high
hardness to compete diamond. Boron rich solids are good candidates
owing to their short interatomic bond lengths and strong covalent
character. Boron containing hard material was synthesized by modifiedmicrowave
method under nitrogen atmosphere by using a fuel
(glycine or urea), amorphous boron and/or boric acid in appropriate
molar ratio. Characterizations were done by x-ray diffraction (XRD),
Fourier transform infrared (FTIR) spectroscopy, scanning electron
microscopy/energy dispersive analyze (SEM/EDS), thermo
gravimetric/differential thermal analysis (TG/DTA).
Abstract: A novel Active Flap System (AFS) has been developed
at DTU Wind Energy, as a result of a 3-year R&D project following
almost 10 years of innovative research in this field. The full scale AFS
comprises an active deformable trailing edge has been tested at the
unique rotating test facility at the Risø Campus of DTU Wind Energy
in Denmark. The design and instrumentation of the wing section and
the AFS are described. The general description and objectives of the
rotating test rig at the Risø campus of DTU are presented, along
with an overview of sensors on the setup and the test cases. The
post-processing of data is discussed and results of steady, flap step
and azimuth control flap cases are presented.
Abstract: Carefully scheduling the operations of pumps can be
resulted to significant energy savings. Schedules can be defined
either implicit, in terms of other elements of the network such as tank
levels, or explicit by specifying the time during which each pump is
on/off. In this study, two new explicit representations based on timecontrolled
triggers were analyzed, where the maximum number of
pump switches was established beforehand, and the schedule may
contain fewer switches than the maximum. The optimal operation of
pumping stations was determined using a Jumping Particle Swarm
Optimization (JPSO) algorithm to achieve the minimum energy cost.
The model integrates JPSO optimizer and EPANET hydraulic
network solver. The optimal pump operation schedule of VanZyl
water distribution system was determined using the proposed model
and compared with those from Genetic and Ant Colony algorithms.
The results indicate that the proposed model utilizing the JPSO
algorithm is a versatile management model for the operation of realworld
water distribution system.
Abstract: The moisture content of densified biomass is a
limiting parameter influencing the quality of this solid biofuel. It
influences its calorific value, density, mechanical strength and
dimensional stability as well as affecting its production process. This
paper deals with experimental research into the effect of moisture
content of the densified material on the final quality of biofuel in the
form of logs (briquettes or pellets). Experiments based on the singleaxis
densification of the spruce sawdust were carried out with a
hydraulic piston press (piston and die), where the densified logs were
produced at room temperature. The effect of moisture content on the
qualitative properties of the logs, including density, change of
moisture, expansion and physical changes, and compressive and
impact resistance were studied. The results show the moisture ranges
required for producing good-quality logs. The experiments were
evaluated and the moisture content of the tested material was
optimized to achieve the optimum value for the best quality of the
solid biofuel. The dense logs also have high-energy content per unit
volume. The research results could be used to develop and optimize
industrial technologies and machinery for biomass densification to
achieve high quality solid biofuel.
Abstract: Drought is one of the most serious problems posing a
grave threat to cereals production including maize. Maize
improvement in drought-stress tolerance poses a great challenge as
the global need for food and bio-energy increases. Thus, the current
study was planned to explore the variations and determine the
performance of target traits of maize hybrids at grain growth stage
under drought conditions during 2014 under Adana, Mediterranean
climate conditions, Turkey. Maize hybrids (Sancia, Indaco,
71May69, Aaccel, Calgary, 70May82, 72May80) were evaluated
under (irrigated and water stress). Results revealed that, grain yield
and yield traits had a negative effects because of water stress
conditions compared with the normal irrigation. As well as, based on
the result under normal irrigation, the maximum biological yield and
harvest index were recorded. According to the differences among
hybrids were found that, significant differences were observed among
hybrids with respect to yield and yield traits under current research. Based on the results, grain weight had more effect on grain yield
than grain number during grain filling growth stage under water
stress conditions. In this concern, according to low drought
susceptibility index (less grain yield losses), the hybrid (Indaco) was
more stable in grain number and grain weight. Consequently, it may
be concluded that this hybrid would be recommended for use in the
future breeding programs for production of drought tolerant hybrids.
Abstract: This paper describes how to dimension the electric
components of a 48V hybrid system considering real customer use.
Furthermore, it provides information about savings in energy and
CO2 emissions by a customer-tailored 48V hybrid. Based on measured customer profiles, the electric units such as the
electric motor and the energy storage are dimensioned. Furthermore,
the CO2 reduction potential in real customer use is determined
compared to conventional vehicles. Finally, investigations are carried
out to specify the topology design and preliminary considerations in
order to hybridize a conventional vehicle with a 48V hybrid system.
The emission model results from an empiric approach also taking into
account the effects of engine dynamics on emissions. We analyzed
transient engine emissions during representative customer driving
profiles and created emission meta models. The investigation showed
a significant difference in emissions when simulating realistic
customer driving profiles using the created verified meta models
compared to static approaches which are commonly used for vehicle
simulation.
Abstract: A sliding door system is used in commercial vehicles
and passenger cars to allow a larger unobstructed access to the
interior for loading and unloading. The movement of a sliding door
on vehicle body is ensured by mechanisms and tracks having special
cross-section which is manufactured by roll forming and stretch
bending process. There are three tracks and three mechanisms which
are called upper, central and lower on a sliding door system. There
are static requirements as strength on different directions, rigidity for
mechanisms, door drop off, door sag; dynamic requirements as high
energy slam opening-closing and durability requirement to validate
these products. In addition, there is a kinematic requirement to find
out force values from door handle during manual operating. In this
study, finite element analysis and physical test results which are
realized for sliding door systems will be shared comparatively.
Abstract: Ultraviolet photocatalytic oxidation (UV-PCO)
technology has been recommended as a green approach to health
indoor environment when it is integrated into mechanical ventilation
systems for inorganic and organic compounds removal as well as
energy saving due to less outdoor air intakes. Although much research
has been devoted to UV-PCO, limited information is available on the
UV-PCO behavior tested by the mixtures in literature. This project
investigated UV-PCO performance and by-product generation using a
single and a mixture of acetone and MEK at 100 ppb each in a
single-pass duct system in an effort to obtain knowledge associated
with competitive photochemical reactions involved in. The
experiments were performed at 20 % RH, 22 °C, and a gas flow rate of
128 m3/h (75 cfm). Results show that acetone and MEK mutually
reduced each other’s PCO removal efficiency, particularly negative
removal efficiency for acetone. These findings were different from
previous observation of facilitatory effects on the adsorption of
acetone and MEK on photocatalyst surfaces.
Abstract: In most existing buildings in hot climate, cooling
loads lead to high primary energy consumption and consequently
high CO2 emissions. These can be substantially decreased with
integrated renewable energy systems. Kuwait is characterized by its
dry hot long summer and short warm winter. Kuwait receives annual
total radiation more than 5280 MJ/m2 with approximately 3347 h of
sunshine. Solar energy systems consist of PV modules and parabolic
trough collectors are considered to satisfy electricity consumption,
domestic water heating, and cooling loads of an existing building.
This paper presents the results of an extensive program of energy
conservation and energy generation using integrated photovoltaic
(PV) modules and Parabolic Trough Collectors (PTC). The program
conducted on an existing institutional building intending to convert it
into a Net-Zero Energy Building (NZEB) or near net Zero Energy
Building (nNZEB). The program consists of two phases; the first
phase is concerned with energy auditing and energy conservation
measures at minimum cost and the second phase considers the
installation of photovoltaic modules and parabolic trough collectors.
The 2-storey building under consideration is the Applied Sciences
Department at the College of Technological Studies, Kuwait. Single
effect lithium bromide water absorption chillers are implemented to
provide air conditioning load to the building. A numerical model is
developed to evaluate the performance of parabolic trough collectors
in Kuwait climate. Transient simulation program (TRNSYS) is
adapted to simulate the performance of different solar system
components. In addition, a numerical model is developed to assess
the environmental impacts of building integrated renewable energy
systems. Results indicate that efficient energy conservation can play
an important role in converting the existing buildings into NZEBs as
it saves a significant portion of annual energy consumption of the
building. The first phase results in an energy conservation of about
28% of the building consumption. In the second phase, the integrated
PV completely covers the lighting and equipment loads of the
building. On the other hand, parabolic trough collectors of optimum
area of 765 m2 can satisfy a significant portion of the cooling load,
i.e about73% of the total building cooling load. The annual avoided
CO2 emission is evaluated at the optimum conditions to assess the
environmental impacts of renewable energy systems. The total annual
avoided CO2 emission is about 680 metric ton/year which confirms
the environmental impacts of these systems in Kuwait.