Abstract: This paper reported an experimental research of
steady-state heat transfer behaviour of a gas flowing through a fixed
bed under the different operating conditions. Studies had been carried
out in a fixed-bed packed methanol synthesis catalyst percolated by air
at appropriate flow rate. Both radial and axial direction temperature
distribution had been investigated under the different operating
conditions. The effects of operating conditions including the reactor
inlet air temperature, the heating pipe temperature and the air flow rate
on temperature distribution was investigated and the experimental
results showed that a higher inlet air temperature was conducive to
uniform temperature distribution in the fixed bed. A large temperature
drop existed at the radial direction, and the temperature drop increased
with the heating pipe temperature increasing under the experimental
conditions; the temperature profile of the vicinity of the heating pipe
was strongly affected by the heating pipe temperature. A higher air
flow rate can improve the heat transfer in the fixed bed. Based on the
thermal distribution, heat transfer models of the fixed bed could be
established, and the characteristics of the temperature distribution in
the fixed bed could be finely described, that had an important practical
significance.
Abstract: This paper presents an analysis result of relationship
between business and information technology (IT) in business process
reengineering (BPR). 258 Japanese firm-level data collected have been
analyzed using structural equation modeling. This analysis was aimed
to illuminating success factors of achieve effective BPR. Analysis was
focused on management factors (including organizational factors) and
implementing management method (e.g. balanced score card, internal
control, etc.).These results would contribute for achieving effective
BPR by showing effective tasks and environment to be focused.
Abstract: Materials used on exterior spacecraft surfaces are subjected to many environmental threats which can cause degradation, atomic oxygen is one of the most threats. We prepared organic silicon atomic-oxygen-protection film using method of polymerization. This paper presented the effects on the film structure and its durability of the preparation processing, and analyzed the polymerization theory, the film structure and composition of the film. At last, we tested the film in our ground based atomic oxygen simulator, and indicated that the film worked well.
Abstract: Some Chromium (III) complexes were synthesized
with three amino acids: L Glutamic Acid, Glycine, and L-cysteine as
the ligands, in order to provide a new supplement containing Cr(III)
for patients with type 2 diabetes mellitus. The complexes have been
prepared by refluxing a mixture of Chromium(III) chloride in
aqueous solution with L-glutamic acid, Glycine, and L-cysteine after
pH adjustment by sodium hydroxide. These complexes were
characterized by Infrared and Uv-Vis spectrophotometer and
Elemental analyzer. The product yields of four products were 87.50
and 56.76% for Cr-Glu complexes, 46.70% for Cr-Gly complex and
40.08% for Cr-Cys complex respectively. The predicted structure of
the complexes are [Cr(glu)2(H2O)2].xH2O, Cr(gly)3..xH2O and
Cr(cys)3.xH2O., respectively.
Abstract: This paper features the modeling and design of a
Robust Decentralized Fast Output Sampling (RDFOS) Feedback
control technique for the active vibration control of a smart flexible
multimodel Euler-Bernoulli cantilever beams for a multivariable
(MIMO) case by retaining the first 6 vibratory modes. The beam
structure is modeled in state space form using the concept of
piezoelectric theory, the Euler-Bernoulli beam theory and the Finite
Element Method (FEM) technique by dividing the beam into 4 finite
elements and placing the piezoelectric sensor / actuator at two finite
element locations (positions 2 and 4) as collocated pairs, i.e., as
surface mounted sensor / actuator, thus giving rise to a multivariable
model of the smart structure plant with two inputs and two outputs.
Five such multivariable models are obtained by varying the
dimensions (aspect ratios) of the aluminium beam. Using model
order reduction technique, the reduced order model of the higher
order system is obtained based on dominant Eigen value retention
and the Davison technique. RDFOS feedback controllers are
designed for the above 5 multivariable-multimodel plant. The closed
loop responses with the RDFOS feedback gain and the magnitudes of
the control input are obtained and the performance of the proposed
multimodel smart structure system is evaluated for vibration control.
Abstract: The ε4 allele of the ε2, ε3 and ε4 protein isoform polymorphism in the gene encoding apolipoprotein E (Apo E) has previously been associated with increased cardiac artery disease (CAD); therefore to investigate the significance of this polymorphism in pathogenesis of CAD in Iranian patients with stenosis and control subjects. To investigate the association between
Apo E polymorphism and coronary artery disease we performed a comparative case control study of the frequency of Apo E
polymorphism in One hundred CAD patients with stenosis who underwent coronary angiography (>50% stenosis) and 100 control subjects (
Abstract: For a given specific problem an efficient algorithm has been the matter of study. However, an alternative approach orthogonal to this approach comes out, which is called a reduction. In general for a given specific problem this reduction approach studies how to convert an original problem into subproblems. This paper proposes a formal modeling language to support this reduction approach in order to make a solver quickly. We show three examples from the wide area of learning problems. The benefit is a fast prototyping of algorithms for a given new problem. It is noted that our formal modeling language is not intend for providing an efficient notation for data mining application, but for facilitating a designer who develops solvers in machine learning.
Abstract: In this paper, we present a cost-effective wireless
distributed load shedding system for non-emergency scenarios. In
power transformer locations where SCADA system cannot be used,
the proposed solution provides a reasonable alternative that combines
the use of microcontrollers and existing GSM infrastructure to send
early warning SMS messages to users advising them to proactively
reduce their power consumption before system capacity is reached
and systematic power shutdown takes place.
A novel communication protocol and message set have been
devised to handle the messaging between the transformer sites, where
the microcontrollers are located and where the measurements take
place, and the central processing site where the database server is
hosted. Moreover, the system sends warning messages to the endusers
mobile devices that are used as communication terminals. The
system has been implemented and tested via different experimental
results.
Abstract: The Taiwan government has started to promote the “Plain Landscape Afforestation and Greening Program" since 2002. A key task of the program was the payment for environmental services (PES), entitled the “Plain Landscape Afforestation Policy" (PLAP), which was certificated by the Executive Yuan on August 31, 2001 and enacted on January 1, 2002. According to the policy, it is estimated that the total area of afforestation will be 25,100 hectares by December 31, 2007. Until the end of 2007, the policy had been enacted for six years in total and the actual area of afforestation was 8,919.18 hectares. Among them, Taiwan Sugar Corporation (TSC) was accounted for 7,960 hectares (with 2,450.83 hectares as public service area) which occupied 86.22% of the total afforestation area; the private farmland promoted by local governments was accounted for 869.18 hectares which occupied 9.75% of the total afforestation area. Based on the above, we observe that most of the afforestation area in this policy is executed by TSC, and the achievement ratio by TSC is better than by others. It implies that the success of the PLAP is seriously related to the execution of TSC. The objective of this study is to analyze the relevant policy planning of TSC's participation in the PLAP, suggest complementary measures, and draw up effective adjustment mechanisms, so as to improve the effectiveness of executing the policy. Our main conclusions and suggestions are summarized as follows: 1. The main reason for TSC’s participation in the PLAP is based on their passive cooperation with the central government or company policy. Prior to TSC’s participation in the PLAP, their lands were mainly used for growing sugarcane. 2. The main factors of TSC's consideration on the selection of tree species are based on the suitability of land and species. The largest proportion of tree species is allocated to economic forests, and the lack of technical instruction was the main problem during afforestation. Moreover, the method of improving TSC’s future development in leisure agriculture and landscape business becomes a key topic. 3. TSC has developed short and long-term plans on participating in the PLAP for the future. However, there is no great willingness or incentive on budgeting for such detailed planning. 4. Most people from TSC interviewed consider the requirements on PLAP unreasonable. Among them, an unreasonable requirement on the number of trees accounted for the greatest proportion; furthermore, most interviewees suggested that the government should continue to provide incentives even after 20 years. 5. Since the government shares the same goals as TSC, there should be sufficient cooperation and communication that support the technical instruction and reduction of afforestation cost, which will also help to improve effectiveness of the policy.
Abstract: In the paper, a fast high-resolution range profile synthetic algorithm called orthogonal matching pursuit with sensing dictionary (OMP-SD) is proposed. It formulates the traditional HRRP synthetic to be a sparse approximation problem over redundant dictionary. As it employs a priori that the synthetic range profile (SRP) of targets are sparse, SRP can be accomplished even in presence of data lost. Besides, the computation complexity decreases from O(MNDK) flops for OMP to O(M(N + D)K) flops for OMP-SD by introducing sensing dictionary (SD). Simulation experiments illustrate its advantages both in additive white Gaussian noise (AWGN) and noiseless situation, respectively.
Abstract: Today-s Information and Knowledge Society has
placed new demands on education and a new paradigm of education
is required. Learning, facilitated by educational systems and the
pedagogic process, is globally undergoing dramatic changes. The aim
of this paper is the development of a simple Instructional Design tool
for E-Learning, named IDEL (Instructional Design for Electronic
Learning), that provides the educators with facilities to create their
own courses with the essential educational material and manage
communication with students. It offers flexibility in the way of
learning and provides ease in employment and reusability of
resources. IDEL is a web-based Instructional System and is designed
to facilitate course design process in accordance with the ADDIE
model and the instructional design principles with emphasis placed
on the use of technology enhanced learning. An example case of
using the ADDIE model to systematically develop a course and its
implementation with the aid of IDEL is given and some results from
student evaluation of the tool and the course are reported.
Abstract: The objective of this research was to investigate biodegradation of water hyacinth (Eichhornia crassipes) to produce bioethanol using dilute-acid pretreatment (1% sulfuric acid) results in high hemicellulose decomposition and using yeast (Pachysolen tannophilus) as bioethanol producing strain. A maximum ethanol yield of 1.14g/L with coefficient, 0.24g g-1; productivity, 0.015g l-1h-1 was comparable to predicted value 32.05g/L obtained by Central Composite Design (CCD). Maximum ethanol yield coefficient was comparable to those obtained through enzymatic saccharification and fermentation of acid hydrolysate using fully equipped fermentor. Although maximum ethanol concentration was low in lab scale, the improvement of lignocellulosic ethanol yield is necessary for large scale production.
Abstract: This study was carried out to reveal the bacterial composition of aerosol in the studied abattoirs. Bacteria isolated were characterized according to microbiological standards. Factors such as temperature and distance were considered as variable in this study. The isolation was carried out at different temperatures such as 27oC, 31oC and 29oC and at various distances of 100meters and 200meters away from the slaughter sites. Result obtained showed that strains of Staphylococcus aureus, Escherichia coli, Bacillus subtilis, Lactobacillus alimentarius and Micrococcus sp. were identified. The total viable counts showed that more microorganisms were present in the morning while the least viable count of 388cfu was recorded in the evening period of this study. This study also showed that more microbial loads were recorded the further the distance is to the slaughter site. Conclusively, the array of bacteria isolated suggests that abattoir sites may be a potential source of pathogenic organisms to commuters if located within residential environment.
Abstract: This paper presents a new method for read out of the piezoresistive accelerometer sensors. The circuit works based on Instrumentation amplifier and it is useful for reducing offset In Wheatstone Bridge. The obtained gain is 645 with 1μv/°c Equivalent drift and 1.58mw power consumption. A Schmitt trigger and multiplexer circuit control output node. a high speed counter is designed in this work .the proposed circuit is designed and simulated In 0.18μm CMOS technology with 1.8v power supply.
Abstract: Flash floods are considered natural disasters that can
cause casualties and demolishing of infra structures. The problem is
that flash floods, particularly in arid and semi arid zones, take place
in very short time. So, it is important to forecast flash floods earlier to
its events with a lead time up to 48 hours to give early warning alert
to avoid or minimize disasters. The flash flood took place over Wadi
Watier - Sinai Peninsula, in October 24th, 2008, has been simulated,
investigated and analyzed using the state of the art regional weather
model. The Weather Research and Forecast (WRF) model, which is a
reliable short term forecasting tool for precipitation events, has been
utilized over the study area. The model results have been calibrated
with the real data, for the same date and time, of the rainfall
measurements recorded at Sorah gauging station. The WRF model
forecasted total rainfall of 11.6 mm while the real measured one was
10.8 mm. The calibration shows significant consistency between
WRF model and real measurements results.
Abstract: Based on general proportional integral (GPI) observers and sliding mode control technique, a robust control method is proposed for the master-slave synchronization of chaotic systems in the presence of parameter uncertainty and with partially measurable output signal. By using GPI observer, the master dynamics are reconstructed by the observations from a measurable output under the differential algebraic framework. Driven by the signals provided by GPI observer, a sliding mode control technique is used for the tracking control and synchronization of the master-slave dynamics. The convincing numerical results reveal the proposed method is effective, and successfully accommodate the system uncertainties, disturbances, and noisy corruptions.
Abstract: Using Internet communication, new home electronics
have functions of monitoring and control from remote. However in
many case these electronics work as standalone, and old electronics
are not followed. Then, we developed the total remote system include
not only new electronics but olds. This systems node is a adapter of
electrical power plug that embed relay switch and some sensors, and
these nodes communicate with each other. the system server was build
on the Internet, and users access to this system from web browsers.
To reduce the cost to set up of this system, communication between
adapters are used ZigBee wireless network instead of wired LAN
cable[3]. From measured RSSI(received signal strength indicator)
information between each nodes, the system can estimate roughly
adapters were mounted on which room, and where in the room. So
also it reduces the cost of mapping nodes. Using this system, energy
saving and house monitoring are expected.
Abstract: Series of experimental tests were conducted on a
section of a 660 kW wind turbine blade to measure the pressure
distribution of this model oscillating in plunging motion. In order to
minimize the amount of data required to predict aerodynamic loads
of the airfoil, a General Regression Neural Network, GRNN, was
trained using the measured experimental data. The network once
proved to be accurate enough, was used to predict the flow behavior
of the airfoil for the desired conditions.
Results showed that with using a few of the acquired data, the
trained neural network was able to predict accurate results with
minimal errors when compared with the corresponding measured
values. Therefore with employing this trained network the
aerodynamic coefficients of the plunging airfoil, are predicted
accurately at different oscillation frequencies, amplitudes, and angles
of attack; hence reducing the cost of tests while achieving acceptable
accuracy.
Abstract: The classical temporal scan statistic is often used to
identify disease clusters. In recent years, this method has become as a
very popular technique and its field of application has been notably
increased. Many bioinformatic problems have been solved with this
technique. In this paper a new scan fuzzy method is proposed. The
behaviors of classic and fuzzy scan techniques are studied with
simulated data. ROC curves are calculated, being demonstrated the
superiority of the fuzzy scan technique.
Abstract: InGaAsN and GaAsN epitaxial layers with similar
nitrogen compositions in a sample were successfully grown on a
GaAs (001) substrate by solid source molecular beam epitaxy. An
electron cyclotron resonance nitrogen plasma source has been used to
generate atomic nitrogen during the growth of the nitride layers. The
indium composition changed from sample to sample to give
compressive and tensile strained InGaAsN layers. Layer
characteristics have been assessed by high-resolution x-ray
diffraction to determine the relationship between the lattice constant
of the GaAs1-yNy layer and the fraction x of In. The objective was to
determine the In fraction x in an InxGa1-xAs1-yNy epitaxial layer which
exactly cancels the strain present in a GaAs1-yNy epitaxial layer with
the same nitrogen content when grown on a GaAs substrate.