Abstract: A nanocrystalline thin film of ZnSe was successfully
electrodeposited on copper substrate using a non-aqueous solution
and subsequently annealed in air at 400°C. XRD analysis indicates
the polycrystalline deposit of (111) plane in both the cases. The
sharpness of the peak increases due to annealing of the film and
average grain size increases to 20 nm to 27nm. SEM photograph
indicate that grains are uniform and densely distributed over the
surface. Annealing increases the average grain size by 20%. The EDS
spectroscopy shows the ratio of Zn & Se is 1.1 in case of annealed
film. AFM analysis indicates the average roughness of the film
reduces from 181nm to 165nm due to annealing of the film. The
bandgap also decreases from 2.71eV to 2.62eV.
Abstract: The main objective of aircraft aerodynamics is to
enhance the aerodynamic characteristics and maneuverability of the
aircraft. This enhancement includes the reduction in drag and stall
phenomenon. The airfoil which contains dimples will have
comparatively less drag than the plain airfoil. Introducing dimples on
the aircraft wing will create turbulence by creating vortices which
delays the boundary layer separation resulting in decrease of pressure
drag and also increase in the angle of stall. In addition, wake
reduction leads to reduction in acoustic emission. The overall
objective of this paper is to improve the aircraft maneuverability by
delaying the flow separation point at stall and thereby reducing the
drag by applying the dimple effect over the aircraft wing. This project
includes both computational and experimental analysis of dimple
effect on aircraft wing, using NACA 0018 airfoil. Dimple shapes of
Semi-sphere, hexagon, cylinder, square are selected for the analysis;
airfoil is tested under the inlet velocity of 30m/s and 60m/s at
different angle of attack (5˚, 10˚, 15˚, 20˚, and 25˚). This analysis
favors the dimple effect by increasing L/D ratio and thereby
providing the maximum aerodynamic efficiency, which provides the
enhanced performance for the aircraft.
Abstract: The goal of this study is to identify success factors
that could influence the ISMS self-implementation in government
sector from qualitative perspective. This study is based on a case
study in one of the Malaysian government agency. Semi-structured
interviews involving five key informants were conducted to examine
factors addressed in the conceptual framework. Subsequently,
thematic analysis was executed to describe the influence of each
factor on the success implementation of ISMS. The result of this
study indicates that management commitment, implementer
commitment and implementer competency are part of the success
factors for ISMS self-implementation in Malaysian Government
Sector.
Abstract: The seismic responses of steel buildings with semirigid
post-tensioned connections (PC) are estimated and compared
with those of steel buildings with typical rigid (welded) connections
(RC). The comparison is made in terms of global and local response
parameters. The results indicate that the seismic responses in terms of
interstory shears, roof displacements, axial load and bending
moments are smaller for the buildings with PC connection. The
difference is larger for global than for local parameters, which in turn
varies from one column location to another. The reason for this
improved behavior is that the buildings with PC dissipate more
hysteretic energy than those with RC. In addition, unlike the case of
buildings with WC, for the PC structures the hysteretic energy is
mostly dissipated at the connections, which implies that structural
damage in beams and columns is not significant. According to these
results, steel buildings with PC are a viable option in high seismicity
areas because of their smaller response and self-centering connection
capacity as well as the fact that brittle failure is avoided.
Abstract: Human leukocyte antigen (HLA) typing from next
generation sequencing (NGS) data has the potential for applications in
clinical laboratories and population genetic studies. Here we introduce
a novel technique for HLA typing from NGS data based on
read-mapping using a comprehensive reference panel containing all
known HLA alleles and de novo assembly of the gene-specific short
reads. An accurate HLA typing at high-digit resolution was achieved
when it was tested on publicly available NGS data, outperforming
other newly-developed tools such as HLAminer and PHLAT.
Abstract: In this research (using induction furnace process)
nodular iron with three different percentages of copper (residual,
0.5% and 1,2%) was obtained. Chemical analysis was performed by
mass spectrometry and microstructures were characterized by Optical
Microscopy (ASTM E3) and Scanning Electron Microscopy (SEM).
The study of mechanical behavior was carried out in a mechanical
test machine (ASTM E8) and a Pin on disk tribometer (ASTM G99)
was used to assess wear resistance. It is observed that the dissolution
of copper in crystal lattice increases the pearlite structure improving
the wear and hardness behavior, but producing a contrary effect on
the energy absorption.
Abstract: Fluid viscous damping systems are well suited for
many air vehicles subjected to shock and vibration. These damping
system work with the principle of viscous fluid throttling through the
orifice to create huge pressure difference between compression and
rebound chamber and obtain the required damping force. One
application of such systems is its use in aircraft door system to
counteract the door’s velocity and safely stop it. In exigency
situations like crash or emergency landing where the door doesn’t
open easily, possibly due to unusually tilting of fuselage or some
obstacles or intrusion of debris obstruction to move the parts of the
door, such system can be combined with other systems to provide
needed force to forcefully open the door and also securely stop it
simultaneously within the required time i.e. less than 8 seconds. In
the present study, a hydraulic system called snubber along with other
systems like actuator, gas bottle assembly which together known as
emergency power assist system (EPAS) is designed, built and
experimentally studied to check the magnitude of angular velocity,
damping force and time required to effectively open the door.
Whenever needed, the gas pressure from the bottle is released to
actuate the actuator and at the same time pull the snubber’s piston to
operate the emergency opening of the door. Such EPAS installed in
the suspension arm of the aircraft door is studied explicitly changing
parameters like orifice size, oil level, oil viscosity and bypass valve
gap and its spring of the snubber at varying temperature to generate
the optimum design case. Comparative analysis of the EPAS at
several cases is done and conclusions are made. It is found that
during emergency condition, the system opening time and angular
velocity, when snubber with 0.3mm piston and shaft orifice and
bypass valve gap of 0.5 mm with its original spring is used, shows
significant improvement over the old ones.
Abstract: The paper deals with the problems of the actual
behavior, failure mechanism and load-carrying capacity of the special
bolt connection developed and intended for the assembly connections
of truss main girders of perspective railway temporary steel bridges.
Within the framework of this problem solution, several types of
structural details of assembly joints have been considered as the
conceptual structural design. Based on the preliminary evaluation of
advantages or disadvantages of these ones, in principle two basic
structural configurations – so-called “tooth” and “splice-plate”
connections have been selected for the subsequent detailed
investigation. This investigation is mainly based on the experimental
verification of the actual behavior, strain and failure mechanism and
corresponding strength of the connection, and on its numerical
modeling using FEM. This paper is focused only on the cyclic
loading (fatigue) tests results of “splice-plate” connections and their
evaluation, which have already been finished. Simultaneously with
the fatigue tests, the static loading tests have been realized too, but
these ones, as well as FEM numerical modeling, are not the subject of
this paper.
Abstract: The Blue Nile Basin is the most important tributary of
the Nile River. Egypt and Sudan are almost dependent on water
originated from the Blue Nile. This multi-dependency creates
conflicts among the three countries Egypt, Sudan, and Ethiopia
making the management of these conflicts as an international issue.
Good assessment of the water resources of the Blue Nile is an
important to help in managing such conflicts. Hydrological models
are good tool for such assessment. This paper presents a critical
review of the nature and variability of the climate and hydrology of
the Blue Nile Basin as a first step of using hydrological modeling to
assess the water resources of the Blue Nile. Many several attempts
are done to develop basin-scale hydrological modeling on the Blue
Nile. Lumped and semi distributed models used averages of
meteorological inputs and watershed characteristics in hydrological
simulation, to analyze runoff for flood control and water resource
management. Distributed models include the temporal and spatial
variability of catchment conditions and meteorological inputs to
allow better representation of the hydrological process. The main
challenge of all used models was to assess the water resources of the
basin is the shortage of the data needed for models calibration and
validation. It is recommended to use distributed model for their
higher accuracy to cope with the great variability and complexity of
the Blue Nile basin and to collect sufficient data to have more
sophisticated and accurate hydrological modeling.
Abstract: In recent years, the hair building fiber has become
popular, in other words, it is an effective method which helps people
who suffer hair loss or sparse hair since the hair building fiber is
capable to create a natural look of simulated hair rapidly. In the
markets, there are a lot of hair fiber brands that have been designed to
formulate an intense bond with hair strands and make the hair appear
more voluminous instantly. However, those products have their own
set of properties. Thus, in this report, some measurement techniques
are proposed to identify those products. Up to five different brands of
hair fiber are tested. The electrostatic and dielectric properties of the
hair fibers are macroscopically tested using design DC and high
frequency microwave techniques. Besides, the hair fibers are
microscopically analysis by magnifying the structures of the fiber
using scanning electron microscope (SEM). From the SEM photos,
the comparison of the uniformly shaped and broken rate of the hair
fibers in the different bulk samples can be observed respectively.
Abstract: This paper introduces an original method of
parametric optimization of the structure for multimodal decisionlevel
fusion scheme which combines the results of the partial solution
of the classification task obtained from assembly of the mono-modal
classifiers. As a result, a multimodal fusion classifier which has the
minimum value of the total error rate has been obtained.
Abstract: Microbial fuel cells (MFCs) represent a promising
technology for simultaneous bioelectricity generation and wastewater
treatment. Catalysts are significant portions of the cost of microbial
fuel cell cathodes. Many materials have been tested as aqueous
cathodes, but air-cathodes are needed to avoid energy demands for
water aeration. The sluggish oxygen reduction reaction (ORR) rate at
air cathode necessitates efficient electrocatalyst such as carbon
supported platinum catalyst (Pt/C) which is very costly. Manganese
oxide (MnO2) was a representative metal oxide which has been
studied as a promising alternative electrocatalyst for ORR and has
been tested in air-cathode MFCs. However the single MnO2 has poor
electric conductivity and low stability. In the present work, the MnO2
catalyst has been modified by doping Pt nanoparticle. The goal of the
work was to improve the performance of the MFC with minimum Pt
loading. MnO2 and Pt nanoparticles were prepared by hydrothermal
and sol gel methods, respectively. Wet impregnation method was
used to synthesize Pt/MnO2 catalyst. The catalysts were further used
as cathode catalysts in air-cathode cubic MFCs, in which anaerobic
sludge was inoculated as biocatalysts and palm oil mill effluent
(POME) was used as the substrate in the anode chamber. The asprepared
Pt/MnO2 was characterized comprehensively through field
emission scanning electron microscope (FESEM), X-Ray diffraction
(XRD), X-ray photoelectron spectroscopy (XPS), and cyclic
voltammetry (CV) where its surface morphology, crystallinity,
oxidation state and electrochemical activity were examined,
respectively. XPS revealed Mn (IV) oxidation state and Pt (0)
nanoparticle metal, indicating the presence of MnO2 and Pt.
Morphology of Pt/MnO2 observed from FESEM shows that the
doping of Pt did not cause change in needle-like shape of MnO2
which provides large contacting surface area. The electrochemical
active area of the Pt/MnO2 catalysts has been increased from 276 to
617 m2/g with the increase in Pt loading from 0.2 to 0.8 wt%. The
CV results in O2 saturated neutral Na2SO4 solution showed that
MnO2 and Pt/MnO2 catalysts could catalyze ORR with different
catalytic activities. MFC with Pt/MnO2 (0.4 wt% Pt) as air cathode
catalyst generates a maximum power density of 165 mW/m3, which
is higher than that of MFC with MnO2 catalyst (95 mW/m3). The
open circuit voltage (OCV) of the MFC operated with MnO2 cathode
gradually decreased during 14 days of operation, whereas the MFC
with Pt/MnO2 cathode remained almost constant throughout the
operation suggesting the higher stability of the Pt/MnO2 catalyst.
Therefore, Pt/MnO2 with 0.4 wt% Pt successfully demonstrated as an
efficient and low cost electrocatalyst for ORR in air cathode MFC with higher electrochemical activity, stability and hence enhanced
performance.
Abstract: The main aim of this research was to investigate a
prototype bamboo shading device. There were two objectives to this
study: first, to investigate the effects of non-chemical treatments on
bamboo shading devices damaged by powder-post beetles and fungi,
and second to develop a prototype bamboo shading device. This
study of the effects of non-chemical treatments on bamboo shading
devices damage by powder-post beetles in the laboratory showed
that, among seven treatments tested, wood vinegar treatment can
protect powder-post beetles better than the original method by up to
92.91%. It was also found that wood vinegar treatment shows the
best performance in fungi protection and works better than the
original method by up to 40%. A second experiment was carried out
by constructing four bamboo shading devices and installing them on
a building for 28 days. All aspects of shading device were
investigated in terms of their beauty, durability, and ease of
construction and assembly. The final prototype was developed from
the lessons learned from the test results. In conclusion, this study
showed the effectiveness of some natural preservatives against insect
and fungi damage, and it also illustrated the characteristics of a
prototype bamboo shading device that can be constructed by rural
workers within one week.
Abstract: A large amount of data is typically stored in relational
databases (DB). The latter can efficiently handle user queries which
intend to elicit the appropriate information from data sources.
However, direct access and use of this data requires the end users to
have an adequate technical background, while they should also cope
with the internal data structure and values presented. Consequently
the information retrieval is a quite difficult process even for IT or DB
experts, taking into account the limited contributions of relational
databases from the conceptual point of view. Ontologies enable users
to formally describe a domain of knowledge in terms of concepts and
relations among them and hence they can be used for unambiguously
specifying the information captured by the relational database.
However, accessing information residing in a database using
ontologies is feasible, provided that the users are keen on using
semantic web technologies. For enabling users form different
disciplines to retrieve the appropriate data, the design of a Graphical
User Interface is necessary. In this work, we will present an
interactive, ontology-based, semantically enable web tool that can be
used for information retrieval purposes. The tool is totally based on
the ontological representation of underlying database schema while it
provides a user friendly environment through which the users can
graphically form and execute their queries.
Abstract: In order to study the aerodynamic performance of a
semi-flexible membrane wing, Fluid-Structure Interaction simulations
have been performed. The fluid problem has been modeled using
two different approaches which are the vortex panel method and the
numerical solution of the Navier-Stokes equations. Nonlinear analysis
of the structural problem is performed using the Finite Element
Method. Comparison between the two fluid solvers has been made.
Aerodynamic performance of the wing is discussed regarding its
lift and drag coefficients and they are compared with those of the
equivalent rigid wing.
Abstract: Diffusion stills have been effective in water
desalination. The present work represents a model of the distillation
process by using vertical single-effect diffusion stills. A semianalytical
model has been developed to model the process. A
software computer code using Engineering Equation Solver EES
software has been developed to solve the equations of the developed
model. An experimental setup has been constructed, and used for the
validation of the model. The model is also validated against former
literature results. The results obtained from the present experimental
test rig, and the data from the literature, have been compared with the
results of the code to find its best range of validity. In addition, a
parametric analysis of the system has been developed using the
model to determine the effect of operating conditions on the system's
performance. The dominant parameters that affect the productivity of
the still are the hot plate temperature that ranges from (55- 90°C) and
feed flow rate in range of (0.00694-0.0211 kg/m2-s).
Abstract: Waste silicon carbide (waste SiC) filled high-density
polyethylene (HDPE) with and without surface modifiers were
studied. Two types of surface modifiers namely; high-density
polyethylene-grafted-maleic anhydride (HDPE-g-MA) and 3-aminopropyltriethoxysilane have been used in this study. The
composites were produced using a two roll mill, extruder and shaped
in a hydraulic compression molding machine. The mechanical
properties of polymer composites such as flexural strength and
modulus, impact strength, tensile strength, stiffness and hardness
were investigated over a range of compositions. It was found that,
flexural strength and modulus, tensile modulus and hardness
increased, whereas impact strength and tensile strength decreased
with the increasing in filler contents, compared to the neat HDPE. At
similar filler content, the effect of both surface modifiers increased
flexural modulus, impact strength, tensile strength and stiffness but
reduced the flexural strength. Morphological investigation using
SEM revealed that the improvement in mechanical properties was
due to enhancement of the interfacial adhesion between waste SiC
and HDPE.
Abstract: This research focused on comparing the critical
thinking of the teacher students before and after using Miller’s Model
learning activities and investigating their opinions. The sampling
groups were (1) fourth year 33 student teachers majoring in Early
Childhood Education and enrolling in semester 1 of academic year
2013 (2) third year 28 student teachers majoring in English and
enrolling in semester 2 of academic year 2013 and (3) third year 22
student teachers majoring in Thai and enrolling in semester 2 of
academic year 2013. The research instruments were (1) lesson plans
where the learning activities were settled based on Miller’s Model (2)
critical thinking assessment criteria and (3) a questionnaire on
opinions towards Miller’s Model based learning activities. The
statistical treatment was mean, deviation, different scores and T-test.
The result unfolded that (1) the critical thinking of the students after
the assigned activities was better than before and (2) the students’
opinions towards the critical thinking improvement activities based
on Miller’s Model ranged from the level of high to highest.
Abstract: Numeracy, like Literacy is considered to be a core
value of modern societies. Most higher education institutions in
South Africa include being numerate as an important graduate
attribute. It is argued that a suitability numerate society contributes to
social justice, empowerment, financial and environmental
sustainability and a lack of numeracy practices can contribute to
disempowerment.
Numeracy is commonly misconstrued as a basic and simple
practice, similar in nature to basic arithmetic. This study highlights
the complexities of higher education numeracy practices by analyzing
a programme in a higher education institution in South Africa using
the New Literacies Studies perspective.
Abstract: Bio-composites derived from plant fiber and/or bioderived
polymer, are likely more ecofriendly and demonstrate
competitive performance with petroleum based composites. In this
research, the bio phenol-formaldehyde (bio-PF) was used as a matrix
and oil palm empty fruit bunch fiber (EFB) as reinforcement. The
matrix was synthesized via liquefaction and condensation to enhance
the combination of phenol and formaldehyde, during the process.
Then, the bio-PF was mixed with different percentage of EFB (5%,
10%, 15% and 20%) and molded at 180oC. The samples that viewed
under scanning electron microscopy (SEM) showed an excellent
wettability and interaction between EFB and matrix. Samples of 10%
EFB gave the optimum properties of impact and hardness meanwhile
sample 15% of EFB gave the highest reading of flexural modulus
(MOE) and flexural strength (MOR). For thermal stability analysis, it
was found that the weight loss and the activation energy (Ea) of the
bio-composites samples were decreased as the filler content
increased.