Abstract: A simple, accurate and precise direct spectrophotometric method has been developed for the determination of cefixime in tablets and capsules. The method is based on the reaction of cefixime with a mixture of potassium iodide and potassium iodate to form yellow coloured product in ethanol-distilled water medium at room temperature which absorbed maximally at 352 nm. The factors affecting the reaction product were carefully studied and optimized. The validation parameters based on International Conference on Harmonisation (ICH, USA) guidelines were followed. The effect of common excipients used as additives has been tested and the tolerance limit was calculated for the determination of cefixime. Beer’s law is obeyed in the concentration range of 4 – 24 ug mL-1 with apparent molar absorptivity of 1.52 × 104 L mol-1cm-1 and Sandell’s sensitivity of 0.033 ug/cm2/ 0.001 absorbance unit. The limits of detection and quantitation for the proposed method are 0.32 and 1.06 ug mL-1, respectively. The proposed method has been successfully applied for the determination of cefixime in pharmaceutical formulations. The results obtained by the proposed method were statistically compared with the reference method using t- and F- values and found no significant difference between the two methods. The proposed method can be used as an alternate method for routine quality control analysis of cefixime in pharmaceutical formulations.
Abstract: This paper explores competencies that managers of
small firms in Ghana use to enhance operational flexibility towards
the attainment of higher productivity. This is because the requisite
competence required of such managers to be effective performers
continues to be a challenge. Data was collected from managers of
three hundred small firms using a standardized self-completion
questionnaire and analyzed using the Amos-based structural equation
model approach. Findings from factor and confirmatory factor
analyses showed that the only competence exhibited by managers
toward effective performance is realistic practices evident at the
workplace. It is concluded that a manager’s self-confidence and
involvement in areas that he/she is good at, and his/her possession of
skills that enables performance at high capacity are indications of the
manger’s effectiveness. The study outcome provides a knowledge
base helpful to policy-makers, especially in Ghana, in determining
the requisite managerial competences required by small firm
managers for effective performance.
Abstract: Nowadays, the amounts of companies which tend to
have an Enterprise Resource Planning (ERP) application are
increasing. Although ERP projects are expensive, time consuming,
and complex, there are some successful experiences. These days,
developing countries are striving to implement ERP projects
successfully; however, there are many obstacles. Therefore, these
projects would be failed or partially failed. This paper concerns the
implementation of a successful ERP implementation, IFS, in Iran at
Dana Geophysics Company (DGC). After a short review of ERP and
ERP market in Iran, we propose a three phases deployment
methodology (phase 1: Preparation and Business Process
Management (BPM) phase 2: implementation and phase 3: testing,
golive-1 (pilot) and golive-2 (final)). Then, we present five guidelines
(Project Management, Change Management, Business Process
Management (BPM), Training& Knowledge Management, and
Technical Management), which were chose as work streams. In this
case study we present lessons learned in Project management and
Business process Management.
Abstract: The main objective of this study was to identify
factors and conditions that motivated and encouraged students
towards the math class and the factors that made this class an
attractive and lovely one. To do this end, questionnaires consisting of
15 questions were distributed among 85 math teachers working in
schools of Zahedan. Having collected and reviewed these
questionnaires, it was shown that doing activity in math class
(activity of students while teaching) and previous math teachers'
behaviors have had much impact on encouraging the students
towards mathematics. Separation of educational classroom of
mathematics from the main classroom (which is decorated with crafts
created by students themselves with regard to math book including
article, wall newspaper, figures and formulas), peers, size and
appearance of math book, first grade teachers in each educational
level, among whom the Elementary first grade teachers had more
importance and impact, were among the most influential and
important factors in this regard. Then, school environment, family,
conducting research related to mathematics, its application in daily
life and other courses and studying the history of mathematics were
categorized as important factors that would increase the students’
interest in mathematics.
Abstract: This paper deals with a simulation programs and
technologies using in the educational process for members of the crisis
management. Risk analysis, simulation, preparation and planning are
among the main activities of workers of crisis management. Made
correctly simulation of emergency defines the extent of the danger. On
this basis, it is possible to effectively prepare and plan measures to
minimize damage. The paper is focused on simulation programs that
are trained at the University of Defence. Implementation of the outputs
from simulation programs in decision-making processes of crisis staffs
is one of the main tasks of the research project.
Abstract: This paper deals with a protection of the national and
European infrastructure. It is issue nowadays. The paper deals with
the perspectives and possibilities of "smart solutions" to critical
infrastructure protection. The research project deals with computers
aided technologies are used from the perspective of new, better
protection of selected infrastructure objects. Protection is focused on
communication and information channels. These communication and
information channels are very important for the functioning of the
system of protection of critical infrastructure elements.
Abstract: Chloride resistance in Ultra High Performance
Concrete (UHPC) is determined in this paper. This work deals with
the one dimension chloride transport, which can be potentially
dangerous particularly for the durability of concrete structures. Risk
of reinforcement corrosion due to exposure to the concrete surface to
direct the action of chloride ions (mainly in the form de-icing salts or
groundwater) is dangerously increases. The measured data are
investigated depending on the depth of penetration of chloride ions
into the concrete structure. Comparative measurements with normal
strength concrete are done as well. The experimental results showed
that UHCP have improved resistance of chlorides penetration than
NSC and also chloride diffusion depth is significantly lower in
UHCP.
Abstract: The aim of this work is to present a theoretical analysis of a 2D ultrasound transducer comprised of crossed arrays of metal strips placed on both sides of thin piezoelectric layer (a). Such a structure is capable of electronic beam-steering of generated wavebeam both in elevation and azimuth. In this paper a semi-analytical model of the considered transducer is developed. It is based on generalization of the well-known BIS-expansion method. Specifically, applying the electrostatic approximation, the electric field components on the surface of the layer are expanded into fast converging series of double periodic spatial harmonics with corresponding amplitudes represented by the properly chosen Legendre polynomials. The problem is reduced to numerical solving of certain system of linear equations for unknown expansion coefficients.
Abstract: In this numerical study, we want to present the design
of highly efficient extruded-type heat sink. The symmetrically
arranged extruded-type heat sinks are used instead of a single extruded
or swaged-type heat sink. In this parametric study, the maximum
temperatures, the base temperatures between heaters, and the heat
release rates were investigated with respect to the arrangements of heat
sources, air flow rates, and amounts of heat input. Based on the results
we believe that the use of both side of heat sink is to be much better for
release the heat than the use of single side. Also from the results, it is
believed that the symmetric arrangement of heat sources is
recommended to achieve a higher heat transfer from the heat sink.
Abstract: In this study, the evaluation of thermal stability of the
micrometer-sized silica particle reinforced epoxy composite was
carried out through the measurement of thermal expansion coefficient
and Young’s modulus of the specimens. For all the specimens in this
study from the baseline to those containing 50 wt% silica filler, the
thermal expansion coefficients and the Young’s moduli were
gradually decreased down to 20% and increased up to 41%,
respectively. The experimental results were compared with fillervolume-
based simple empirical relations. The experimental results of
thermal expansion coefficients correspond with those of Thomas’s
model which is modified from the rule of mixture. However, the
measured result for Young’s modulus tends to be increased slightly.
The differences in increments of the moduli between experimental and
numerical model data are quite large.
Abstract: The reduction of greenhouse gases emissions is highly
discussed ecological theme at present. In addition to power industry
also main production sectors of binders, i.e. cement, air and hydraulic
lime are very sensitive to these questions. One of the possibilities
how CO2 emissions can be reduced directly at clinker burnout is
represented by partial substitution of lime with a material containing
limy ions at absence of carbonate group. Fluidised fly ash is one of
such potential raw materials where CaO can be found free and also
bound in anhydrite, CaSO4. At application of FBC (fluidized bed
combustion) fly ash with approximate 20% CaO content and its
dosing ratio to high percent lime 1:2, corresponding stechiometrically
to the preparation of raw material powder, approximately 0,37 t CO2
per 1 ton of one-component cement would be released at clinker
burnout compared to 0,46 t CO2 when orthodox raw materials are
used. The reduction of CO2 emissions thus could reach even 20%.
Abstract: The aim of the present study is to investigate the
potential use of the selected seed oils. The oil was extracted using
Soxhlet apparatus and the physicochemical characteristics of the oil
determined using standard methods. The following results were
obtained for the physicochemical parameters analysed: for Egusi seed
oil, Oil yield 53.20%, Saponification value 178.03±1.25 mgKOH/g,
Iodine value 49.10±0.32 g I2/100g, Acid value 4.30±0.86 mgKOH/g,
and Peroxide value 5.80±0.27 meq/kg were obtained. For Pawpaw
seed oil, Oil yield 40.10%, Saponification value 24.13±3.93
mgKOH/g, Iodine value 24.87±0.19 g I2/100g, Acid value 9.46±0.40
mgKOH/g, and Peroxide value 3.12±1.22 meq/kg were obtained. For
Sweet orange seed oil, Oil yield 43.10%, Saponification value
106.30±2.37 mgKOH/g, Iodine value 37.08±0.04 g I2/100g, Acid
value 7.59±0.77 mgKOH/g, and Peroxide value 2.21±0.46 meq/kg
were obtained. From the obtained values of the determined
parameters, the oils can be extracted from the three selected seeds in
commercial quantities and that the egusi and sweet orange seed oils
may be utilized in the industrial soap production.
Abstract: A method which allows a diabetic quadriplegic patient
that has had four limb amputations (above the knee and elbow) to
self-administer injections of insulin has been designed. The aim of
this research project is to improve a quadriplegic patient’s selfmanagement,
affected by diabetes, by designing a suitable device for
self-administering insulin.
The quadriplegic patient affected by diabetes has to be able to selfadminister
insulin safely and independently to guarantee stable
healthy conditions. The device also should be designed to adapt to a
number of different varying personal characteristics such as height
and body weight.
Abstract: Kinematic data wisely correlate vector quantities in
space to scalar parameters in time to assess the degree of symmetry
between the intact limb and the amputated limb with respect to a
normal model derived from the gait of control group participants.
Furthermore, these particular data allow a doctor to preliminarily
evaluate the usefulness of a certain rehabilitation therapy.
Kinetic curves allow the analysis of ground reaction forces (GRFs)
to assess the appropriateness of human motion.
Electromyography (EMG) allows the analysis of the fundamental
lower limb force contributions to quantify the level of gait
asymmetry. However, the use of this technological tool is expensive
and requires patient’s hospitalization. This research work suggests
overcoming the above limitations by applying artificial neural
networks.
Abstract: In this research work, neural networks were applied to
classify two types of hip joint implants based on the relative hip joint
implant side speed and three components of each ground reaction
force. The condition of walking gait at normal velocity was used and
carried out with each of the two hip joint implants assessed. Ground
reaction forces’ kinetic temporal changes were considered in the first
approach followed but discarded in the second one. Ground reaction
force components were obtained from eighteen patients under such
gait condition, half of which had a hip implant type I-II, whilst the
other half had the hip implant, defined as type III by Orthoload®.
After pre-processing raw gait kinetic data and selecting the time
frames needed for the analysis, the ground reaction force components
were used to train a MLP neural network, which learnt to distinguish
the two hip joint implants in the abovementioned condition. Further
to training, unknown hip implant side and ground reaction force
components were presented to the neural networks, which assigned
those features into the right class with a reasonably high accuracy for
the hip implant type I-II and the type III. The results suggest that
neural networks could be successfully applied in the performance
assessment of hip joint implants.
Abstract: Red River Gum (Eucalyptus camaldulensis) is a tree
of the genus Eucalyptus widely distributed in Algeria and in the
world. The value of its aromatic secondary metabolites offers new
perspectives in the pharmaceutical industry. This strategy can
contribute to the sustainable development of our country. Preliminary
tests performed on the essential oil of Eucalyptus camendulensis
showed that this oil has antibacterial activity vis-à-vis the bacterial
strains (Enterococcus feacalis, Enterobacter cloaceai, Proteus
microsilis, Escherichia coli, Klebsiella pneumonia, and Pseudomonas
aeruginosa) and antifungic (Fusarium sporotrichioide and Fusarium
graminearum). The culture medium used was nutrient broth Muller
Hinton. The interaction between the bacteria and the essential oil is
expressed by a zone of inhibition with diameters of MIC indirectly
expression of. And we used the PDA medium to determine the fungal
activity. The extraction of the aromatic fraction (essentially oilhydrolat)
of the fresh aerian part of the Eucalyptus camendulensis
was performed by hydrodistillation. The average essential oil yield is
0.99%. The antimicrobial and fungal study of the essential oil and
hydrosol showed a high inhibitory effect on the growth of pathogens.
Abstract: Audio-lingual Method (ALM) is a teaching approach
that is claimed that ineffective for teaching second/foreign languages.
Because some linguists and second/foreign language teachers believe
that ALM is a rote learning style. However, this study is done on a
belief that ALM will be able to solve Thais’ English speaking
problem. This paper aims to report the findings on teaching English
speaking to adult learners with an “adapted ALM”, one distinction of
which is to use Thai as the medium language of instruction.
The participants are consisted of 9 adult learners. They were
allowed to speak English more freely using both the materials
presented in the class and their background knowledge of English. At
the end of the course, they spoke English more fluently, more
confidently, to the extent that they applied what they learnt both in
and outside the class.
Abstract: Over the past era, there have been a lot of efforts and
studies are carried out in growing proficient tools for performing
various tasks in big data. Recently big data have gotten a lot of
publicity for their good reasons. Due to the large and complex
collection of datasets it is difficult to process on traditional data
processing applications. This concern turns to be further mandatory
for producing various tools in big data. Moreover, the main aim of
big data analytics is to utilize the advanced analytic techniques
besides very huge, different datasets which contain diverse sizes from
terabytes to zettabytes and diverse types such as structured or
unstructured and batch or streaming. Big data is useful for data sets
where their size or type is away from the capability of traditional
relational databases for capturing, managing and processing the data
with low-latency. Thus the out coming challenges tend to the
occurrence of powerful big data tools. In this survey, a various
collection of big data tools are illustrated and also compared with the
salient features.
Abstract: The lactic acid bacteria (LAB) were isolated from
10 samples of fermented foods (Sa-tor-dong and Bodo) in South
locality of Thailand. The 23 isolates of lactic acid bacteria were
selected, which were exhibited a clear zone and growth on MRS
agar supplemented with CaCO3. All of lactic acid bacteria were
tested on morphological and biochemical. The result showed that
all isolates were Gram’s positive, non-spore forming but only
10 isolates displayed catalase negative. The 10 isolates including
BD1 .1, BD 1.2, BD 2.1, BD2.2, BD 2.3, BD 3.1, BD 4.1, BD 5.2,
ST 4.1 and ST 5.2 were selected for inhibition activity
determination. Only 2 strains (ST 4.1 and BD 2.3) showed
inhibition zone on agar, when using Escherichia coli sp. as target
strain. The ST 4.1 showed highest inhibition zone on agar, which
was selected for probiotic property testing. The ST4.1 isolate
could grow in MRS broth containing a high concentration of
sodium chloride 6%, bile salts 7%, pH 4-10 and vary temperature
at 15-45°C.
Abstract: With demand for primary energy continuously
growing, search for renewable and efficient energy sources has been
high on agenda of our society. One of the most promising energy
sources is biogas technology. Residues coming from dairy industry
and milk processing could be used in biogas production; however,
low efficiency and high cost impede wide application of such
technology. One of the main problems is management and conversion
of organic residues through the anaerobic digestion process which is
characterized by acidic environment due to the low whey pH (