Abstract: In this paper, thick walled Cylindrical tanks or tubes
made of functionally graded material under internal pressure and
temperature gradient are studied. Material parameters have been
considered as power functions. They play important role in the
elastoplastic behavior of these materials. To clarify their role,
different materials with different parameters have been used under
temperature gradient. Finally, their effect and loading effect have
been determined in first yield point. Also, the important role of
temperature gradient was also shown. At the end the study has been
results obtained from changes in the elastic modulus and yield stress.
Also special attention is also given to the effects of this internal
pressure and temperature gradient in the creation of tensile and
compressive stresses.
Abstract: This article presents a new vibration diagnostic
method designed to (PM) machines with permanent magnets. Those
devices are commonly used in small wind and water systems or
vehicles drives. The author’s method is very innovative and unique.
Specific structural properties of PM machines are used in this method
- electromotive force (EMF) generated due to vibrations. There was
analysed number of publications which describe vibration diagnostic
methods and tests of electrical PM machines and there was no
method found to determine the technical condition of such machine
basing on their own signals. In this article will be discussed: the
method genesis, the similarity of machines with permanent magnet to
vibration sensor and simulation and laboratory tests results. The
method of determination the technical condition of electrical machine
with permanent magnets basing on its own signals is the subject of
patent application and it is the main thesis of author’s doctoral
dissertation.
Abstract: This research focuses on the optimization of glazed
surfaces and the assessment of possible solar gains in industrial
buildings. Existing window rating methods for single windows were
evaluated and a new method for a simple analysis of energy gains and
losses by single windows was introduced. Furthermore extensive
transient building simulations were carried out to appraise the
performance of low cost polycarbonate multi-cell sheets in
interaction with typical buildings for industrial applications. Mainly
energy saving potential was determined by optimizing the orientation
and area of such glazing systems in dependency on their thermal
qualities. Moreover the impact on critical aspects such as summer
overheating and daylight illumination was considered to ensure the
user comfort and avoid additional energy demand for lighting or
cooling. Hereby the simulated heating demand could be reduced by
up to 1/3 compared to traditional architecture of industrial halls using
mainly skylights.
Abstract: Novel bio-based polymer electrolyte was synthesized
with LiClO4 as the main source of charge carrier. Initially,
polyurethane-LiClO4 polymer electrolytes were synthesized via
prepolymerization method with different NCO/OH ratios and labelled
them as PU1, PU2, PU3 and PU4. Fourier transform infrared (FTIR)
analysis indicates the co-ordination between Li+ ion and polyurethane
in PU1. Differential scanning calorimetry (DSC) analysis indicates
PU1 has the highest glass transition temperature (Tg) corresponds to
the most abundant urethane group which is the hard segment in PU1.
Scanning electron microscopy (SEM) shows the good miscibility
between lithium salt and the polymer. The study found that PU1
possessed the greatest ionic conductivity and the lowest activation
energy, Ea. All the polyurethanes exhibited linear Arrhenius
variations indicating ion transport via simple lithium ion hopping in
polyurethane. This research proves the NCO content in polyurethane
plays an important role in affecting the ionic conductivity of this
polymer electrolyte.
Abstract: The effect of trucks on the level of service is
determined by considering passenger car equivalents (PCE) of trucks.
The current version of Highway Capacity Manual (HCM) uses a
single PCE value for all tucks combined. However, the composition
of truck traffic varies from location to location; therefore, a single
PCE value for all trucks may not correctly represent the impact of
truck traffic at specific locations. Consequently, present study
developed separate PCE values for single-unit and combination
trucks to replace the single value provided in the HCM on different
freeways. Site specific PCE values, were developed using concept of
spatial lagging headways (that is the distance between rear bumpers
of two vehicles in a traffic stream) measured from field traffic data.
The study used data from four locations on a single urban freeway
and three different rural freeways in Indiana. Three-stage-leastsquares
(3SLS) regression techniques were used to generate models
that predicted lagging headways for passenger cars, single unit trucks
(SUT), and combination trucks (CT). The estimated PCE values for
single-unit and combination truck for basic urban freeways (level
terrain) were: 1.35 and 1.60, respectively. For rural freeways the
estimated PCE values for single-unit and combination truck were:
1.30 and 1.45, respectively. As expected, traffic variables such as
vehicle flow rates and speed have significant impacts on vehicle
headways. Study results revealed that the use of separate PCE values
for different truck classes can have significant influence on the LOS
estimation.
Abstract: Theoretical optimization of a copper-water negative
inclination heat pipe with internal composite wick structure had been
performed, regarding a new introduced parameter: the ratio between
the coarse mesh wraps and the fine mesh wraps of the composite
wick. Since in many cases, the design of a heat pipe matches specific
thermal requirements and physical limitations, this work
demonstrates the optimization of a 1m length, 8mm internal diameter
heat pipe without an adiabatic section, at a negative inclination angle
of -10º. The optimization is based on a new introduced parameter, LR:
the ratio between the coarse mesh wraps and the fine mesh wraps.
Abstract: In the present work, the effects of additives, including
contents of the added antioxidants and type of the selected metallic
stearates (either calcium stearate (CaSt) or zinc stearate (ZnSt)), on
the thermal stabilities of carbon black (CB)/high density polyethylene
(HDPE) compounds were studied. The results showed that the AO
contents played a key role in the thermal stabilities of the CB/HDPE
compounds — the higher the AO content, the higher the thermal
stabilities. Although the CaSt-containing compounds were slightly
superior to those with ZnSt in terms of the thermal stabilities, the
remaining solid residue of CaSt after heated to the temperature of 600
°C (mainly calcium carbonate (CaCO3) as characterized by the X-ray
diffraction (XRD) technique) seemed to catalyze the decomposition
of CB in the HDPE-based compounds. Hence, the quantification of
CB in the CaSt-containing compounds with a muffle furnace gave an
inaccurate CB content — much lower than actual value. However,
this phenomenon was negligible in the ZnSt-containing system.
Abstract: Polyethylene (PE), Polypropylene (PP), Polyethylene
(vinyl acetate) (EVA) and PE-ionomer nanocomposite samples were
prepared by mixing of the polymer with organofilized
montmorillonite fillers Cloisite 93A and Dellite 67G. The amount of
each modified montmorillonite (MMT) was fixed to 5% (w/w). The
twin-screw kneader was used for the compounding of polymer matrix
and chosen nanofillers. The level of MMT exfoliation was studied by
the transmission electron microscopy (TEM) observations. The
mechanical properties of prepared materials were evaluated by
dynamical mechanical analysis at 30°C and by the measurement of
tensile properties (stress and strain at break).
Abstract: OEE has been used in many industries as measure of
performance. However due to limitations of original OEE, it has been
modified by various researchers. OEE for mining application is
special version of classic equation, carries these limitation over. In
this paper it has been aimed to modify the OEE for mining
application by introducing the weights to the elements of it and
termed as Mine Production index (MPi). As a special application of
new index MPishovel has been developed by authors. This can be used
for evaluating the shovel effectiveness. Based on analysis, utilization
followed by performance and availability were ranked in this order.
To check the applicability of this index, a case study was done on
four electrical and one hydraulic shovel in a Swedish mine. The
results shows that MPishovel can evaluate production effectiveness of
shovels and can determine effectiveness values in optimistic view
compared to OEE. MPi with calculation not only give the
effectiveness but also can predict which elements should be focused
for improving the productivity.
Abstract: This study is an attempt to raise the awareness of the
stakeholders and the authorities on the sensitivity of Algerian
secondary school teachers of English as a Foreign Language about
the students’ loss of English language skills learned during formal
schooling with effort and at expense and the supposed measures to
arrest that loss. Data was collected from secondary school teachers of
EFL and analyzed quantitatively using a questionnaire containing
open-ended and close-ended questions. The results advocate a
consensus about the need for actions to be adopted to make
assessment techniques outcome-oriented. Most of the participants
were in favor of including curricular activities involving
contextualized learning, problem-solving learning critical selfawareness,
self and peer-assisted learning, use of computers and
internet so as to make learners autonomous.
Abstract: Different order modulations combined with different
coding schemes, allow sending more bits per symbol, thus achieving
higher throughputs and better spectral efficiencies. However, it must
also be noted that when using a modulation technique such as 64-
QAM with less overhead bits, better signal-to-noise ratios (SNRs) are
needed to overcome any Inter symbol Interference (ISI) and maintain
a certain bit error ratio (BER). The use of adaptive modulation allows
wireless technologies to yielding higher throughputs while also
covering long distances. The aim of this paper is to implement an
Adaptive Modulation and Coding (AMC) features of the WiMAX
PHY in MATLAB and to analyze the performance of the system in
different channel conditions (AWGN, Rayleigh and Rician fading
channel) with channel estimation and blind equalization. Simulation
results have demonstrated that the increment in modulation order
causes to increment in throughput and BER values. These results
derived a trade-off among modulation order, FFT length, throughput,
BER value and spectral efficiency. The BER changes gradually for
AWGN channel and arbitrarily for Rayleigh and Rician fade
channels.
Abstract: Information and Communication Technologies (ICTs)
are pervasive nowadays, including in education where they are
expected to improve the performance of learners. However, the hope
placed in ICTs to find viable solutions to the problem of poor
academic performance in schools in the developing world has not yet
yielded the expected benefits. This problem serves as a motivation to
this study whose aim is to examine the perceptions of educators on
the advantages and disadvantages of e-learning. This aim will be
subdivided into two types of research objectives. Objectives on the
identification and design of theories and models will be achieved
using content analysis and literature review. However, the objective
on the empirical testing of such theories and models will be achieved
through the survey of educators from different schools in the
Pinetown District of the South African Kwazulu-Natal province.
SPSS is used to quantitatively analyse the data collected by the
questionnaire of this survey using descriptive statistics and Pearson
correlations after assessing the validity and the reliability of the data.
The main hypothesis driving this study is that there is a relationship
between the demographics of educators’ and their adherence to
learning theories on one side, and their perceptions on the advantages
and disadvantages of e-learning on the other side, as argued by
existing research; but this research views these learning theories
under three perspectives: educators’ adherence to self-regulated
learning, to constructivism, and to progressivism. This hypothesis
was fully confirmed by the empirical study except for the
demographic factor where teachers’ level of education was found to
be the only demographic factor affecting the perceptions of educators
on the advantages and disadvantages of e-learning.
Abstract: This paper presents a new method to design nonlinear
feedback linearization controller for PEMFCs (Polymer Electrolyte
Membrane Fuel Cells). A nonlinear controller is designed based on
nonlinear model to prolong the stack life of PEMFCs. Since it is
known that large deviations between hydrogen and oxygen partial
pressures can cause severe membrane damage in the fuel cell,
feedback linearization is applied to the PEMFC system so that the
deviation can be kept as small as possible during disturbances or load
variations. To obtain an accurate feedback linearization controller,
tuning the linear parameters are always important. So in proposed
study NSGA (Non-Dominated Sorting Genetic Algorithm)-II method
was used to tune the designed controller in aim to decrease the
controller tracking error. The simulation result showed that the
proposed method tuned the controller efficiently.
Abstract: Ongoing landscape transformation is one of the major
causes behind disappearance of traditional landscapes, and lead to
species and resource loss. Tree in paddy fields in the northeast of
Thailand is one of those traditional landscapes. Using three different
historical time layers, we acknowledged the severe deforestation and
rapid urbanization happened in the region. Despite the general
thinking of decline in tree density as consequences, the heterogeneous
trend of changes in total tree density in three studied landscapes denied
the hypothesis that number of trees in paddy field depend on the length
of land use practice. On the other hand, due to selection of planting
new trees on levees, existence of trees in paddy field now relies on
their values for human use. Besides, changes in land use and landscape
structure had a significant impact on decision of which tree density
level is considered as suitable for the landscape.
Abstract: The majority of contemporary insulation materials
commonly used in the building industry is made from non-renewable
raw materials; furthermore, their production often brings high energy
costs. A long-term trend as far as sustainable development is
concerned has been the reduction of energy and material demands of
building material production. One of the solutions is the possibility of
using easily renewable natural raw material sources which are
considerably more ecological and their production is mostly less
energy-consuming compared to the production of normal insulations
(mineral wool, polystyrene). The paper describes the results of
research focused on the development of thermal and acoustic
insulation materials based on natural fibres intended for floor
constructions. Given the characteristic open porosity of natural fibre
materials, the hygrothermal behaviour of the developed materials was
studied. Especially the influence of relative humidity and temperature
on thermal insulation properties was observed.
Abstract: The effect of Zn2+, Mg2+, and Ba2+ on Saccharomyces
pastorianus performance was evaluated in this study at independent
and three variable combinations. After 96 h of fermentation, high
wort fermentability (%F) = 29.53 was obtained in medium containing
900:4 ppm Mg2+ + Ba2+. Increased ethanol yield 7.35 %(v/v) and
7.13 %(v/v) were obtained in media containing 900:4 ppm Mg2+ +
Ba2+ and 12:900 ppm Zn2+ + Mg2+. Decrease %F = 22.54 and ethanol
yield 6.18 % (v/v) was obtained in medium containing 12:4 ppm Zn2+
+ Ba2+. In media containing the individual ions, increased %F =
27.94 and 26.03 were recorded for media containing 700 ppm Mg2+
and 2 ppm Ba2+ , with ethanol yield of 7.88% (v/v) and 7.62% (v/v)
respectively. Reduced %F and ethanol yield was observed for 10 ppm
Zn2+ and 4 ppm Ba2+ media. The impact of Ba2+ at 1 and 2 ppm was
significant.
Abstract: This paper presents a model predictive control (MPC)
of a utility interactive (UI) single phase inverter (SPI) for a
photovoltaic (PV) system at residential/distribution level. The
proposed model uses single-phase phase locked loop (PLL) to
synchronize SPI with the grid and performs MPC control in a dq
reference frame. SPI model consists of boost converter (BC),
maximum power point tracking (MPPT) control, and a full bridge
(FB) voltage source inverter (VSI). No PI regulators to tune and
carrier and modulating waves are required to produce switching
sequence. Instead, the operational model of VSI is used to synthesize
sinusoidal current and track the reference. Model is validated using a
three kW PV system at the input of UI-SPI in Matlab/Simulink.
Implementation and results demonstrate simplicity and accuracy, as
well as reliability of the model.
Abstract: This paper focuses on the presentation of results
which were obtained as a part of the project FR-TI 3/742: “System of
Lightweight Materials for Finishing of Buildings with Waste Raw
Materials”. Attention was paid to the light weighting of polymermodified
mortars applicable as adhesives, screeds and repair mortars.
In terms of repair mortars, they were ones intended for the sanitation
of aerated concrete.
Abstract: The objective of the study was to select the survival of
probiotic strains when exposed to acidic and bile salts condition. Four
probiotic strains Lactobacillus casei subsp. rhamnosus TISTR 047,
Lactobacillus casei TISTR 1500, Lactobacillus acidophilus TISTR
1338 and Lactobacillus plantarum TISTR 1465 were cultured in
MRS broth and incubated at 35ºC for 15 hours before being inoculated
into acidic condition 5 M HCl, pH 2 for 2 hours and bile salt 0.3%,
pH 5.8 for 8 hour. The survived probiotics were counted in MRS agar.
Among four stains, Lactobacillus casei subsp. rhamnosus TISTR 047
was the highest tolerance specie. Lactobacillus casei subsp.
rhamnosus TISTR 047 reduced 6.74±0.07 log CFU/ml after growing
in acid and 5.52±0.05 log CFU/ml after growing in bile salt. Then,
double emulsion of microorganisms was chosen to encapsulate before
spray drying. Spray drying was done with the inlet temperature 170ºC
and outlet temperature 80ºC. The results showed that the survival of
encapsulated Lactobacillus casei subsp. rhamnosus TISTR 047 after
spray drying decreased from 9.63 ± 0.32 to 8.31 ± 0.11 log CFU/ml
comparing with non-encapsulated, 9.63 ± 0.32 to 4.06 ± 0.08 log
CFU/ml. Therefore, Lactobacillus casei subsp. rhamnosus TISTR 047
would be able to survive in gastrointestinal and spray drying condition.
Abstract: Advances technology in the field of photogrammetry
replaces analog cameras with reflection on aircraft GPS/IMU system
with a digital aerial camera. In this system, when determining the
position of the camera with the GPS, camera rotations are also
determined by the IMU systems. All around the world, digital aerial
cameras have been used for the photogrammetry applications in the
last ten years. In this way, in terms of the work done in
photogrammetry it is possible to use time effectively, costs to be
reduced to a minimum level, the opportunity to make fast and
accurate.
Geo-referencing techniques that are the cornerstone of the GPS /
INS systems, photogrammetric triangulation of images required for
balancing (interior and exterior orientation) brings flexibility to the
process. Also geo-referencing process; needed in the application of
photogrammetry targets to help to reduce the number of ground
control points. In this study, the use of direct and indirect georeferencing
techniques on the accuracy of the points was investigated
in the production of photogrammetric mapping.