Abstract: In the first part of the research work, an electrolyzer (10.16 cm dia and 24.13 cm height) to produce hydrogen and oxygen was constructed for single slice O2/H2 fuel cell using cation exchange membrane. The electrolyzer performance was tested with 23% NaOH, 30% NaOH, 30% KOH and 35% KOH electrolyte solution with current input 4 amp and 2.84 V from the rectifier. Rates of volume of hydrogen produced were 0.159 cm3/sec, 0.155 cm3/sec, 0.169 cm3/sec and 0.163 cm3/sec respectively from 23% NaOH, 30% NaOH, 30% KOH and 35% KOH solution. Rates of volume of oxygen produced were 0.212 cm3/sec, 0.201 cm3/sec, 0.227 cm3/sec and 0.219 cm3/sec respectively from 23% NaOH, 30% NaOH, 30% KOH and 35% KOH solution (1.5 L). In spite of being tested the increased concentration of electrolyte solution, the gas rate does not change significantly. Therefore, inexpensive 23% NaOH electrolyte solution was chosen to use as the electrolyte in the electrolyzer. In the second part of the research work, graphite serpentine flow plates, fiberglass end plates, stainless steel screen electrodes, silicone rubbers were made to assemble the single slice O2/H2 polymer electrolyte membrane fuel cell (PEMFC).
Abstract: Application of nanoparticles as additives in membrane
synthesis for improving the resistance of membranes against fouling
has triggered recent interest in new membrane types. However, most
nanoparticle-enhanced membranes suffer from the tradeoff between
permeability and selectivity. In this study, nano-WS2 was explored as
the additive in membrane synthesis by non-solvent induced phase
separation. Blended PES-WS2 flat-sheet membranes with the
incorporation of ultra-low concentrations of nanoparticles (from 0.025
to 0.25%, WS2/PES ratio) were manufactured and investigated in
terms of permeability, fouling resistance and solute rejection.
Remarkably, a significant enhancement in the permeability was
observed as a result of the incorporation of ultra-low fractions of
nano-WS2 to the membrane structure. Optimal permeability values
were obtained for modified membranes with 0.10%
nanoparticle/polymer concentration ratios. Furthermore, fouling
resistance and solute rejection were significantly improved by the
incorporation of nanoparticles into the membrane matrix. Specifically,
fouling resistance of modified membrane can increase by around 50%.
Abstract: This paper proposes the numerical simulation of the
investment casting of gold jewelry. It aims to study the behavior of
fluid flow during mould filling and solidification and to optimize the
process parameters, which lead to predict and control casting defects
such as gas porosity and shrinkage porosity. A finite difference
method, computer simulation software FLOW-3D was used to
simulate the jewelry casting process. The simplified model was
designed for both numerical simulation and real casting production.
A set of sensor acquisitions were allocated on the different positions
of the wax tree of the model to detect filling times, while a set of
thermocouples were allocated to detect the temperature during
casting and cooling. Those detected data were applied to validate the
results of the numerical simulation to the results of the real casting.
The resulting comparisons signify that the numerical simulation can
be used as an effective tool in investment-casting-process
optimization and casting-defect prediction.
Abstract: The paper proposes a way of parallel processing of
SURF and Optical Flow for moving object recognition and tracking.
The object recognition and tracking is one of the most important task
in computer vision, however disadvantage are many operations cause
processing speed slower so that it can-t do real-time object recognition
and tracking. The proposed method uses a typical way of feature
extraction SURF and moving object Optical Flow for reduce
disadvantage and real-time moving object recognition and tracking,
and parallel processing techniques for speed improvement. First
analyse that an image from DB and acquired through the camera using
SURF for compared to the same object recognition then set ROI
(Region of Interest) for tracking movement of feature points using
Optical Flow. Secondly, using Multi-Thread is for improved
processing speed and recognition by parallel processing. Finally,
performance is evaluated and verified efficiency of algorithm
throughout the experiment.
Abstract: Droughts are complex, natural hazards that, to a
varying degree, affect some parts of the world every year. The range
of drought impacts is related to drought occurring in different stages
of the hydrological cycle and usually different types of droughts,
such as meteorological, agricultural, hydrological, and socioeconomical
are distinguished. Streamflow drought was analyzed by
the method of truncation level (at 70% level) on daily discharges
measured in 54 hydrometric stations in southwestern Iran. Frequency
analysis was carried out for annual maximum series (AMS) of
drought deficit volume and duration series. Some factors including
physiographic, climatic, geologic, and vegetation cover were studied
as influential factors in the regional analysis. According to the results
of factor analysis, six most effective factors were identified as area,
rainfall from December to February, the percent of area with
Normalized Difference Vegetation Index (NDVI)
Abstract: Knowledge management is a process taking any steps
that needed to get the most out of available knowledge resources.
KM involved several steps; capturing the knowledge discovering
new knowledge, sharing the knowledge and applied the knowledge in
the decision making process. In applying the knowledge, it is not
necessary for the individual that use the knowledge to comprehend it
as long as the available knowledge is used in guiding the decision
making and actions. When an expert is called and he provides stepby-
step procedure on how to solve the problems to the caller, the
expert is transferring the knowledge or giving direction to the caller.
And the caller is 'applying' the knowledge by following the
instructions given by the expert. An appropriate mechanism is
needed to ensure effective knowledge transfer which in this case is
by telephone or email. The problem with email and telephone is that
the knowledge is not fully circulated and disseminated to all users. In
this paper, with related experience of local university Help Desk, it is
proposed the usage of Information Technology (IT)to effectively
support the knowledge transfer in the organization. The issues
covered include the existing knowledge, the related works, the
methodology used in defining the knowledge management
requirements as well the overview of the prototype.
Abstract: In this paper, we employ the approach of linear
programming to propose a new interactive broadcast method. In our
method, a film S is divided into n equal parts and broadcast via k
channels. The user simultaneously downloads these segments from k
channels into the user-s set-top-box (STB) and plays them in order.
Our method assumes that the initial p segments will not have
fast-forwarding capabilities. Every time the user wants to initiate d
times fast-forwarding, according to our broadcasting strategy, the
necessary segments already saved in the user-s STB or are just
download on time for playing. The proposed broadcasting strategy not
only allows the user to pause and rewind, but also to fast-forward.
Abstract: The scenario of bypass transition is generally described
as follows: the low-frequency disturbances in the free-stream may
generate long stream-wise streaks in the boundary layer, which later
may trigger secondary instability, leading to rapid increase of
high-frequency disturbances. Then possibly turbulent spots emerge,
and through their merging, lead to fully developed turbulence. This
description, however, is insufficient in the sense that it does not
provide the inherent mechanism of transition that during the transition,
a large number of waves with different frequencies and wave numbers
appear almost simultaneously, producing sufficiently large Reynolds
stress, so the mean flow profile can change rapidly from laminar to
turbulent. In this paper, such a mechanism will be figured out from
analyzing DNS data of transition.
Abstract: A current mirror (CM) based on self cascode MOSFETs low voltage analog and mixed mode structures has been proposed. The proposed CM has high output impedance and can operate at 0.5 V. P-Spice simulations confirm the high performance of this CM with a bandwidth of 6.0 GHz at input current of 100 μA.
Abstract: Images are important in disease research, education,
and clinical medicine. This paper presents a Web Service Platform
(WSP) for support multiple programming languages to access image
from biomedical databases. The main function WSP is to allow web
users access image from biomedical databases. The WSP will
receive web user-s queries. After that, it will send to Querying
Server (QS) and the QS will search and retrieve data from
biomedical databases. Finally, the information will display to the
web users. Simple application is developed and tested for
experiment purpose. Result from experiment indicated WSP can be
used in biomedical environment.
Abstract: Software projects are very dynamic and require
recurring adjustments of their project plans. These settings can be
understood as reconfigurations in the schedule, in the resources
allocation and other design elements. Yet, during the planning and
execution of a software project, the integration of specific activities
in the projects with the activities that take part in the organization-s
common activity flow should be considered. This article presents the
results from a systematic review of aspects related to software
projects- dynamic reconfiguration emphasizing the integration of
project management with the organizational flows. A series of studies
was analyzed from the year 2000 to the present. The results of this
work show that there is a diversity of techniques and strategies for
dynamic reconfiguration of software projects-. However, few
approaches consider the integration of software project activities with
the activities that take part in the organization-s common workflow.
Abstract: This research involved fingerprints on ballistics after shooting. Two objectives of research were as follow; (1) to study the duration of the existence of latent fingerprints on .38, .45, 9 mm and .223 cartridge case after shooting, and (2) to compare the effectiveness of the detection of latent fingerprints by Black Powder, Super Glue, Perma Blue and Gun Bluing. The latent fingerprint appearance were studied on .38, .45, 9 mm. and .223 cartridge cases before and after shooting with Black Powder, Super Glue, Perma Blue and Gun Bluing. The detection times were 3 minute, 6, 12, 18, 24, 30, 36, 42, 48, 54, 60, 66, 72, 78 and 84 hours respectively. As a result of the study, it can be conclude that
Before shooting, the detection of latent fingerprints on 38, .45, and 9 mm. and .223 cartridge cases with Black Powder, Super Glue, Perma Blue and Gun Bluing can detect the fingerprints at all detection times.
After shooting, the detection of latent fingerprints on .38, .45, 9 mm. and .223 cartridge cases with Black Powder, Super Glue did not appear. The detection of latent fingerprints on .38, .45, 9 mm. cartridge cases with Perma Blue and Gun Bluing were found 100% of the time and the detection of latent fingerprints on .223 cartridge cases with Perma Blue and Gun Bluing were found 40% and 46.67% of the time, respectively.
Abstract: This paper proposes a low-cost reconfigurable
architecture for AES algorithm. The proposed architecture separates
SubBytes and MixColumns into two parallel data path, and supports
different bit-width operation for this two data path. As a result, different number of S-box can be supported in this architecture. The
throughput and power consumption can be adjusted by changing the
number of S-box running in this design. Using the TSMC 0.18μm CMOS standard cell library, a very low-cost implementation of 7K
Gates is obtained under 182MHz frequency. The maximum throughput is 360Mbps while using 4 S-Box simultaneously, and the
minimum throughput is 114Mbps while only using 1 S-Box
Abstract: Liposomal magnetofection is the most powerful nonviral method for the nucleic acid delivery into the cultured cancer cells and widely used for in vitro applications. Use of the static magnetic field condition may result in non-uniform distribution of aggregate complexes on the surface of cultured cells. To prevent this, we developed the new device which allows to concentrate aggregate complexes under dynamic magnetic field, assisting more contact of these complexes with cellular membrane and, possibly, stimulating endocytosis. Newly developed device for magnetofection under dynamic gradient magnetic field, “DynaFECTOR", was used to compare transfection efficiency of human liver hepatocellular carcinoma cell line HepG2 with that obtained by lipofection and magnetofection. The effect of two parameters on transfection efficiency, incubation time under dynamic magnetic field and rotation frequency of magnet, was estimated. Liposomal magnetofection under dynamic gradient magnetic field showed the highest transfection efficiency for HepG2 cells.
Abstract: One of the essential requirements in order to have a
realistic surgical simulator is real-time interaction by means of a
haptic interface is. In fact, reproducing haptic sensations increases
the realism of the simulation. However, the interaction need to be
performed in real-time, since a delay between the user action and the
system reaction reduces the user immersion. In this paper, we present
a prototype of the coronary stent implant simulator developed in the
HERMES Project; this system allows real-time interactions with a
artery by means of a specific haptic device; thus the user can
interactively navigate in a reconstructed artery and force feedback is
produced when contact occurs between the artery walls and the
medical instruments
Abstract: In this paper, computational fluid dynamics (CFD) is utilized to characterize a prototype biolistic delivery system, the biomedical device based on the contoured-shock-tube design (CST), with the aim at investigating shocks induced flow instabilities within the contoured shock tube. The shock/interface interactions, the growth of perturbation at an interface between two fluids of different density are interrogated. The key features of the gas dynamics and gas-particle interaction are discussed
Abstract: Asiatic Houbara ( Chlamydotis macqueenii ) is a
flagship and vulnerable species. In-situ conservation of this
threatened species demands for knowledge of its habitat selection.
The aim of this study was to determine habitat variables influencing
birds wintering and breeding selection in semi- arid central Iran.
Habitat features of the detected nest and pellet sites were compared
with paired and random plots by quantifying a number of habitat
variables. In wintering habitat use at micro scale houbara selected
sites where vegetation cover was significantly lower compard to
control sites( p< 0.001). Areas with low number of larger plant
species (p=0.03) that were not too close to a vegetation
patch(p
Abstract: Urban road network traffic has become one of the
most studied research topics in the last decades. This is mainly due to
the enlargement of the cities and the growing number of motor
vehicles traveling in this road network. One of the most sensitive
problems is to verify if the network is congestion-free. Another
related problem is the automatic reconfiguration of the network
without building new roads to alleviate congestions. These problems
require an accurate model of the traffic to determine the steady state
of the system. An alternative is to simulate the traffic to see if there
are congestions and when and where they occur. One key issue is to
find an adequate model for road intersections. Once the model
established, either a large scale model is built or the intersection is
represented by its performance measures and simulation for analysis.
In both cases, it is important to seek the queueing model to represent
the road intersection. In this paper, we propose to model the road
intersection as a BCMP queueing network and we compare this
analytical model against a simulation model for validation.
Abstract: The increasing interest on processing data created by
sensor networks has evolved into approaches to implement sensor
networks as databases. The aggregation operator, which calculates a
value from a large group of data such as computing averages or sums,
etc. is an essential function that needs to be provided when
implementing such sensor network databases. This work proposes to
add the DURING clause into TinySQL to calculate values during a
specific long period and suggests a way to implement the aggregation
service in sensor networks by applying materialized view and
incremental view maintenance techniques that is used in data
warehouses. In sensor networks, data values are passed from child
nodes to parent nodes and an aggregation value is computed at the root
node. As such root nodes need to be memory efficient and low
powered, it becomes a problem to recompute aggregate values from all
past and current data. Therefore, applying incremental view
maintenance techniques can reduce the memory consumption and
support fast computation of aggregate values.
Abstract: Considering non-ideal behavior of fluids and its effects on hydrodynamic and mass transfer in multiphase flow is very essential. Simulations were performed that takes into account the effects of mass transfer and mixture non-ideality on hydrodynamics reported by Irani et al. In this paper, by assuming the density of phases to be constant and Raullt-s law instead of using EOS and fugacity coefficient definition, respectively for both the liquid and gas phases, the importance of non-ideality effects on mass transfer and hydrodynamic behavior was studied. The results for a system of octane/propane (T=323 K, P =445 kpa) also indicated that the assumption of constant density in simulation had major role to diverse from experimental data. Furthermore, comparison between obtained results and the previous report indicated significant differences between experimental data and simulation results with more ideal assumptions.