Abstract: Recently, the advanced technologies that offer high
precision product, relative easy, economical process and also rapid
production are needed to realize the high demand of ultra precision
micro part. In our research, micromanufacturing based on soft
lithography and nanopowder injection molding was investigated. The
silicone metal pattern with ultra thick and high aspect ratio succeeds to
fabricate Polydimethylsiloxane (PDMS) micro mold. The process
followed by nanopowder injection molding (PIM) by a simple vacuum
hot press. The 17-4ph nanopowder with diameter of 100 nm, succeed
to be injected and it forms green sample microbearing with thickness,
microchannel and aspect ratio is 700μm, 60μm and 12, respectively.
Sintering process was done in 1200 C for 2 hours and heating rate
0.83oC/min. Since low powder load (45% PL) was applied to achieve
green sample fabrication, ~15% shrinkage happen in the 86% relative
density. Several improvements should be done to produce high
accuracy and full density sintered part.
Abstract: The Taiwan government has started to promote the “Plain Landscape Afforestation and Greening Program" since 2002. A key task of the program was the payment for environmental services (PES), entitled the “Plain Landscape Afforestation Policy" (PLAP), which was certificated by the Executive Yuan on August 31, 2001 and enacted on January 1, 2002. According to the policy, it is estimated that the total area of afforestation will be 25,100 hectares by December 31, 2007. Until the end of 2007, the policy had been enacted for six years in total and the actual area of afforestation was 8,919.18 hectares. Among them, Taiwan Sugar Corporation (TSC) was accounted for 7,960 hectares (with 2,450.83 hectares as public service area) which occupied 86.22% of the total afforestation area; the private farmland promoted by local governments was accounted for 869.18 hectares which occupied 9.75% of the total afforestation area. Based on the above, we observe that most of the afforestation area in this policy is executed by TSC, and the achievement ratio by TSC is better than by others. It implies that the success of the PLAP is seriously related to the execution of TSC. The objective of this study is to analyze the relevant policy planning of TSC-s participation in the PLAP, suggest complementary measures, and draw up effective adjustment mechanisms, so as to improve the effectiveness of executing the policy. Our main conclusions and suggestions are summarized as follows: 1. The main reason for TSC-s participation in the PLAP is based on their passive cooperation with the central government or company policy. Prior to TSC-s participation in the PLAP, their lands were mainly used for growing sugarcane. 2. The main factors of TSC-s consideration on the selection of tree species are based on the suitability of land and species. The largest proportion of tree species is allocated to economic forests, and the lack of technical instruction was the main problem during afforestation. Moreover, the method of improving TSC-s future development in leisure agriculture and landscape business becomes a key topic. 3. TSC has developed short and long-term plans on participating in the PLAP for the future. However, there is no great willingness or incentive on budgeting for such detailed planning. 4. Most people from TSC interviewed consider the requirements on PLAP unreasonable. Among them, an unreasonable requirement on the number of trees accounted for the greatest proportion; furthermore, most interviewees suggested that the government should continue to provide incentives even after 20 years. 5. Since the government shares the same goals as TSC, there should be sufficient cooperation and communication that support the technical instruction and reduction of afforestation cost, which will also help to improve effectiveness of the policy.
Abstract: This paper investigates and compares performance of
various conventional and fuzzy logic based controllers at generator
locations for oscillation damping. Performance of combination of
conventional and fuzzy logic based controllers also studied by
comparing overshoot on the active power deviation response for a
small disturbance and damping ratio of the critical mode. Fuzzy logic
based controllers can not be modeled in the state space form to get
the eigenvalues and corresponding damping ratios of various modes
of generators and controllers. Hence, a new method based on tracing
envelop of time domain waveform is also presented and used in the
paper for comparing performance of controllers. The paper also
shows that if the fuzzy based controllers designed separately
combining them could not lead to a better performance.
Abstract: The microbiological and physicochemical
characteristics of wetland soils in Eket Local Government Area were
studied between May 2001 and June 2003. Total heterotrophic
bacterial counts (THBC), total fungal counts (TFC), and total
actinomycetes counts (TAC) were determined from soil samples
taken from four locations at two depths in the wet and dry seasons.
Microbial isolates were characterized and identified. Particle size and
chemical parameters were also determined using standard methods.
THBC ranged from 5.2 (+0.17) x106 to 1.7 (+0.18) x107 cfu/g and
from 2.4 (+0.02) x106 to 1.4 (+0.04) x107cfu/g in the wet and dry
seasons, respectively. TFC ranged from 1.8 (+0.03) x106 to 6.6 (+
0.18) x106 cfu/g and from 1.0 (+0.04) x106 to 4.2 (+ 0.01) x106 cfu/g
in the wet and dry seasons, respectively .TAC ranged from 1.2
(+0.53) x106 to 6.0 (+0.05) x106 cfu/g and from 0.6 (+0.01) x106 to
3.2 (+ 0.12) x106 cfu/g in the wet and dry season, respectively.
Acinetobacter, Alcaligenes, Arthrobacter, Bacillus, Beijerinckja,
Enterobacter, Micrococcus, Flavobacterium, Serratia, Enterococcus,
and Pseudomonas species were predominant bacteria while
Aspergillus, Fusarium, Mucor, Penicillium, and Rhizopus were the
dominant fungal genera isolated. Streptomyces and Norcadia were
the actinomycetes genera isolated. The particle size analysis showed
high sand fraction but low silt and clay. The pH and % organic
matter were generally acidic and low, respectively at all locations.
Calcium dominated the exchangeable bases with low electrical
conductivity and micronutrients. These results provide the baseline
data of Eket wetland soils for its management for sustainable
agriculture.
Abstract: The purpose of this study was to investigate the impact of the development of Szuchung Creek take for the cause of the critical success factors, This research is to use the depth interviews, document analysis and Modified-Delphi technique survey of nine depth interviews with experts and 14 experts of Modified-Delphi technique questionnaire and inviting as the research object, Szuchung Creek Hot Springs for the scope of the study. The results show, Szuchung Creek Hot Springs development take for career success factors for the following reasons: 1. Government. 2. Opportunities. 3. Factors of production. 4. Demand conditions. 5. Corporate structure and the degree of competition. 6. Related and supporting industries. Furthermore, Szuchung Creek hot springs, itself already has a number of critical success factors. Contingent less than or inadequacies by Szuchung Creek take for the enterprise development to take for the cause of the critical success factors as the basis for correcting, planning out for local use improvement strategies to achieve the objective of sustainable management.
Abstract: Phase-Contrast MR imaging methods are widely used
for measurement of blood flow velocity components. Also there are
some other tools such as CT and Ultrasound for velocity map
detection in intravascular studies. These data are used in deriving
flow characteristics. Some clinical applications are investigated
which use pressure distribution in diagnosis of intravascular disorders
such as vascular stenosis. In this paper an approach to the problem of
measurement of intravascular pressure field by using velocity field
obtained from flow images is proposed. The method presented in this
paper uses an algorithm to calculate nonlinear equations of Navier-
Stokes, assuming blood as an incompressible and Newtonian fluid.
Flow images usually suffer the lack of spatial resolution. Our
attempt is to consider the effect of spatial resolution on the pressure
distribution estimated from this method. In order to achieve this aim,
velocity map of a numerical phantom is derived at six different
spatial resolutions. To determine the effects of vascular stenoses on
pressure distribution, a stenotic phantom geometry is considered. A
comparison between the pressure distribution obtained from the
phantom and the pressure resulted from the algorithm is presented. In
this regard we also compared the effects of collocated and staggered
computational grids on the pressure distribution resulted from this
algorithm.
Abstract: This paper presents a new heuristic algorithm useful
for long-term planning of survivable WDM networks. A multi-period
model is formulated that combines network topology design and
capacity expansion. The ability to determine network expansion
schedules of this type becomes increasingly important to the
telecommunications industry and to its customers. The solution
technique consists of a Genetic Algorithm that allows generating
several network alternatives for each time period simultaneously and
shortest-path techniques to deduce from these alternatives a least-cost
network expansion plan over all time periods. The multi-period
planning approach is illustrated on a realistic network example.
Extensive simulations on a wide range of problem instances are
carried out to assess the cost savings that can be expected by
choosing a multi-period planning approach instead of an iterative
network expansion design method.
Abstract: Market competition and a desire to gain advantages on globalized market, drives companies towards innovation efforts. Project overload is an unpleasant phenomenon, which is happening for employees inside those organizations trying to make the most efficient use of their resources to be innovative. But what are the impacts of project overload on organization-s innovation capabilities? Advanced engineering teams (AE) inside a major heavy equipment manufacturer are suffering from project overload in their quest for innovation. In this paper, Agent-based modeling (ABM) is used to examine the current reality of the company context, and of the AE team, where the opportunities and challenges for reducing the risk of project overload and moving towards innovation were identified. Project overload is more likely to stifle innovation and creativity inside teams. On the other hand, motivations on proper challenging goals are more likely to help individual to alleviate the negative aspects of low level of project overload.
Abstract: Fecal sterol has been proposed as a chemical indicator
of human fecal pollution even when fecal coliform populations have
diminished due to water chlorination or toxic effects of industrial
effluents. This paper describes an improved derivatization procedure
for simultaneous determination of four fecal sterols including
coprostanol, epicholestanol, cholesterol and cholestanol using gas
chromatography-mass spectrometry (GC-MS), via optimization study
on silylation procedures using N-O-bis
(trimethylsilyl)-trifluoroacetamide (BSTFA), and
N-(tert-butyldimethylsilyl)-N-methyltrifluoroacetamide
(MTBSTFA), which lead to the formation of trimethylsilyl (TMS) and
tert-butyldimethylsilyl (TBS) derivatives, respectively. Two
derivatization processes of injection-port derivatization and water bath
derivatization (60 oC, 1h) were inspected and compared. Furthermore,
the methylation procedure at 25 oC for 2h with
trimethylsilydiazomethane (TMSD) for fecal sterols analysis was also
studied. It was found that most of TMS derivatives demonstrated the
highest sensitivities, followed by methylated derivatives. For BSTFA
or MTBSTFA derivatization processes, the simple injection-port
derivatization process could achieve the same efficiency as that in the
tedious water bath derivatization procedure.
Abstract: Design for Disassembly (DfD) aims to reuse the
structural components instead of demolition followed by recycling of
the demolition debris. This concept preserves the invested embodied
energy of materials, thus reducing inputs of new embodied energy
during materials reprocessing or remanufacturing. Both analytical and
experimental research on a proposed DfD beam-column connection
for use in residential apartments is currently investigated at the
National University of Singapore in collaboration with the Housing
and Development Board of Singapore. The present study reports on
the results of a numerical analysis of the proposed connection utilizing
finite element analysis. The numerical model was calibrated and
validated by comparison against experimental results. Results of a
parametric study will also be presented and discussed.
Abstract: Installation of power compensation equipment in
some cases places additional buses into the system. Therefore, a total
number of power flow equations and voltage unknowns increase due
to additional locations of installed devices. In this circumstance, power flow calculation is more complicated. It may result in a
computational convergence problem. This paper presents a power flow calculation by using Newton-Raphson iterative method together
with the proposed load transfer technique. This concept is to eliminate additional buses by transferring installed loads at the new buses to existing two adjacent buses. Thus, the total number of power
flow equations is not changed. The overall computational speed is
expectedly shorter than that of solving the problem without applying the load transfer technique. A 15-bus test system is employed for test
to evaluate the effectiveness of the proposed load transfer technique. As a result, the total number of iteration required and execution time
is significantly reduced.
Abstract: In this paper is study the possibility of successfully
implementing of hollow roller concept in order to minimize inertial
mass of the large bearings, with major results in diminution of the
material consumption, increasing of power efficiency (in wind power
station area), increasing of the durability and life duration of the large
bearings systems, noise reduction in working, resistance to
vibrations, an important diminution of losses by abrasion and
reduction of the working temperature. In this purpose was developed
an original solution through which are reduced mass, inertial forces
and moments of large bearings by using of hollow rollers. The
research was made by using the method of finite element analysis
applied on software type Solidworks - Nastran. Also, is study the
possibility of rapidly changing the manufacturing system of solid and
hollow cylindrical rollers.
Abstract: Enhancement of the performance of a reverse osmosis
(RO) unit through periodic control is studied. The periodic control
manipulates the feed pressure and flow rate of the RO unit. To ensure
the periodic behavior of the inputs, the manipulated variables (MV)
are transformed into the form of sinusoidal functions. In this case, the
amplitude and period of the sinusoidal functions become the
surrogate MV and are thus regulated via nonlinear model predictive
control algorithm. The simulation results indicated that the control
system can generate cyclic inputs necessary to enhance the closedloop
performance in the sense of increasing the permeate production
and lowering the salt concentration. The proposed control system can
attain its objective with arbitrary set point for the controlled outputs.
Successful results were also obtained in the presence of modeling
errors.
Abstract: We demonstrate a 1×4 coarse wavelength
division-multiplexing (CWDM) planar concave grating
multiplexer/demultiplexer and its application in re-configurable
optical add/drop multiplexer (ROADM) system in silicon-on-insulator
substrate. The wavelengths of the demonstrated concave grating
multiplexer align well with the ITU-T standard. We demonstrate a
prototype of ROADM comprising two such concave gratings and four
wide-band thermo-optical MZI switches. Undercut technology which
removes the underneath silicon substrate is adopted in optical switches
in order to minimize the operation power. For all the thermal heaters,
the operation voltage is smaller than 1.5 V, and the switch power is
~2.4 mW. High throughput pseudorandom binary sequence (PRBS)
data transmission with up to 100 Gb/s is demonstrated, showing the
high-performance ROADM functionality.
Abstract: Periodic vortex shedding in pulsating flow inside wavy
channel and the effect it has on heat transfer are studied using the
finite volume method. A sinusoidally-varying component is superimposed
on a uniform flow inside a sinusoidal wavy channel and
the effects on the Nusselt number is analyzed. It was found that a
unique optimum value of the pulsation frequency, represented by the
Strouhal number, exists for Reynolds numbers ranging from 125 to
1000. Results suggest that the gain in heat transfer is related to the
process of vortex formation, movement about the troughs of the wavy
channel, and subsequent ejection/destruction through the converging
section. Heat transfer is the highest when the frequencies of the
pulsation and vortex formation approach being in-phase. Analysis of
Strouhal number effect on Nu over a period of pulsation substantiates
the proposed physical mechanism for enhancement. The effect of
changing the amplitude of pulsation is also presented over a period
of pulsation, showing a monotonic increase in heat transfer with
increasing amplitude. The 60% increase in Nusselt number suggests
that sinusoidal fluid pulsation can an effective method for enhancing
heat transfer in laminar, wavy-channel flows.
Abstract: Contour filter strips planted with perennial vegetation
can be used to improve surface and ground water quality by reducing
pollutant, such as NO3-N, and sediment outflow from cropland to a
river or lake. Meanwhile, the filter strips of perennial grass with biofuel
potentials also have economic benefits of producing ethanol. In
this study, The Soil and Water Assessment Tool (SWAT) model was
applied to the Walnut Creek Watershed to examine the effectiveness
of contour strips in reducing NO3-N outflows from crop fields to the
river or lake. Required input data include watershed topography,
slope, soil type, land-use, management practices in the watershed and
climate parameters (precipitation, maximum/minimum air
temperature, solar radiation, wind speed and relative humidity).
Numerical experiments were conducted to identify potential
subbasins in the watershed that have high water quality impact, and
to examine the effects of strip size and location on NO3-N reduction
in the subbasins under various meteorological conditions (dry,
average and wet). Variable sizes of contour strips (10%, 20%, 30%
and 50%, respectively, of a subbasin area) planted with perennial
switchgrass were selected for simulating the effects of strip size and
location on stream water quality. Simulation results showed that a
filter strip having 10%-50% of the subbasin area could lead to 55%-
90% NO3-N reduction in the subbasin during an average rainfall
year. Strips occupying 10-20% of the subbasin area were found to be
more efficient in reducing NO3-N when placed along the contour
than that when placed along the river. The results of this study can
assist in cost-benefit analysis and decision-making in best water
resources management practices for environmental protection.
Abstract: The energy consumption of home femto base stations
(BSs) can be reduced, by turning off the Wi-Fi radio interface when
there is no mobile station (MS) under the coverage of the BSs or
MSs do not transmit or receive data packet for long time, especially
in late night. In the energy-efficient home femto BSs, if MSs have
any data packet to transmit and the Wi-Fi radio interface in off
state, MSs wake up the Wi-Fi radio interface of home femto BSs
by using additional low power radio interface. In this paper, the
performance of the energy-efficient home femto BSs from the aspect
of energy consumption and cumulative average delay, and show the
effect of various parameters on energy consumption and cumulative
average delay. From the results, the tradeoff relationship between
energy consumption and cumulative average delay is shown and thus,
appropriate operation should be needed to balance the tradeoff.
Abstract: Neural networks offer an alternative approach both
for identification and control of nonlinear processes in process
engineering. The lack of software tools for the design of controllers
based on neural network models is particularly pronounced in this
field. SIMULINK is properly a widely used graphical code
development environment which allows system-level developers to
perform rapid prototyping and testing. Such graphical based
programming environment involves block-based code development
and offers a more intuitive approach to modeling and control task in
a great variety of engineering disciplines. In this paper a
SIMULINK based Neural Tool has been developed for analysis and
design of multivariable neural based control systems. This tool has
been applied to the control of a high purity distillation column
including non linear hydrodynamic effects. The proposed control
scheme offers an optimal response for both theoretical and practical
challenges posed in process control task, in particular when both,
the quality improvement of distillation products and the operation
efficiency in economical terms are considered.
Abstract: The liberalization and privatization processes have
forced public utility companies to face new competitive challenges,
implementing strategies to gain market share and, at the same time,
keep the old customers. To this end, many companies have carried
out mergers, acquisitions and conglomerations in order to diversify
their business. This paper focuses on companies operating in the free
energy market in Italy. In the last decade, this sector has undergone
profound changes that have radically changed the competitive
scenario and have led companies to implement diversification
strategies of the business. Our work aims to evaluate the economic
and financial performances obtained by energy companies, following
the beginning of the liberalization process, verifying the possible
relationship with the implemented diversification strategies.
Abstract: This article presents a voltage-mode universal
biquadratic filter performing simultaneous 3 standard functions: lowpass,
high-pass and band-pass functions, employing differential
different current conveyor (DDCC) and current controlled current
conveyor (CCCII) as active element. The features of the circuit are
that: the quality factor and pole frequency can be tuned independently
via the input bias currents: the circuit description is very simple,
consisting of 1 DDCC, 2 CCCIIs, 2 electronic resistors and 2
grounded capacitors. Without requiring component matching
conditions, the proposed circuit is very appropriate to further develop
into an integrated circuit. The PSPICE simulation results are
depicted. The given results agree well with the theoretical
anticipation.