Abstract: In industry, on of the most important subjects is die
and it's characteristics in which for cutting and forming different
mechanical pieces, various punch and matrix metal die are used.
whereas the common parts which form the main frame die are not
often proportion with pieces and dies therefore using a part as socalled
common part for frames in specified dimension ranges can
decrease the time of designing, occupied space of warehouse and
manufacturing costs. Parts in dies with getting uniform in their shape
and dimension make common parts of dies. Common parts of punch
and matrix metal die are as bolster, guide bush, guide pillar and
shank. In this paper the common parts and effective parameters in
selecting each of them as the primary information are studied,
afterward for selection and design of mechanical parts an
introduction and investigation based on the Mech. Desk. software is
done hence with developing this software can standardize the metal
common parts of punch and matrix. These studies will be so useful
for designer in their designing and also using it has with very much
advantage for manufactures of products in decreasing occupied
spaces by dies.
Abstract: The purpose of this research was to analyze and compare the instability of a contact surface between Copper and Nickel an alloy cathode in vacuum, the different ratio of Copper and Copper were conducted at 1%, 2% and 4% by using the cathode spot model. The transient recovery voltage is predicted. The cathode spot region is recognized as the collisionless space charge sheath connected with singly ionized collisional plasma. It was found that the transient voltage is decreased with increasing the percentage of an amount of Nickel in cathode materials.
Abstract: The aim of this paper is to investigate the
performance of the developed two point block method designed for
two processors for solving directly non stiff large systems of higher
order ordinary differential equations (ODEs). The method calculates
the numerical solution at two points simultaneously and produces
two new equally spaced solution values within a block and it is
possible to assign the computational tasks at each time step to a
single processor. The algorithm of the method was developed in C
language and the parallel computation was done on a parallel shared
memory environment. Numerical results are given to compare the
efficiency of the developed method to the sequential timing. For
large problems, the parallel implementation produced 1.95 speed-up
and 98% efficiency for the two processors.
Abstract: In this paper, we investigate a blind channel estimation method for Multi-carrier CDMA systems that use a subspace decomposition technique. This technique exploits the orthogonality property between the noise subspace and the received user codes to obtain channel of each user. In the past we used Singular Value Decomposition (SVD) technique but SVD have most computational complexity so in this paper use a new algorithm called URV Decomposition, which serve as an intermediary between the QR decomposition and SVD, replaced in SVD technique to track the noise space of the received data. Because of the URV decomposition has almost the same estimation performance as the SVD, but has less computational complexity.
Abstract: Active vibration control is an important problem in
structures. The objective of active vibration control is to reduce the vibrations of a system by automatic modification of the system-s
structural response. In this paper, the modeling and design of a fast
output sampling feedback controller for a smart flexible beam system embedded with shear sensors and actuators for SISO system using
Timoshenko beam theory is proposed. FEM theory, Timoshenko beam theory and the state space techniques are used to model the
aluminum cantilever beam. For the SISO case, the beam is divided into 5 finite elements and the control actuator is placed at finite
element position 1, whereas the sensor is varied from position 2 to 5, i.e., from the nearby fixed end to the free end. Controllers are
designed using FOS method and the performance of the designed FOS controller is evaluated for vibration control for 4 SISO models
of the same plant. The effect of placing the sensor at different locations on the beam is observed and the performance of the
controller is evaluated for vibration control. Some of the limitations of the Euler-Bernoulli theory such as the neglection of shear and
axial displacement are being considered here, thus giving rise to an accurate beam model. Embedded shear sensors and actuators have
been considered in this paper instead of the surface mounted sensors
and actuators for vibration suppression because of lot of advantages. In controlling the vibration modes, the first three dominant modes of
vibration of the system are considered.
Abstract: This article proposes modeling, simulation and
kinematic and workspace analysis of a spatial cable suspended robot
as incompletely Restrained Positioning Mechanism (IRPM). These
types of robots have six cables equal to the number of degrees of
freedom. After modeling, the kinds of workspace are defined then an
statically reachable combined workspace for different geometric
structures of fixed and moving platform is obtained. This workspace
is defined as the situations of reference point of the moving platform
(center of mass) which under external forces such as weight and with
ignorance of inertial effects, the moving platform should be in static
equilibrium under conditions that length of all cables must not be
exceeded from the maximum value and all of cables must be at
tension (they must have non-negative tension forces). Then the effect
of various parameters such as the size of moving platform, the size of
fixed platform, geometric configuration of robots, magnitude of
applied forces and moments to moving platform on workspace of
these robots with different geometric configuration are investigated.
Obtained results should be effective in employing these robots under
different conditions of applied wrench for increasing the workspace
volume.
Abstract: Web sites are rapidly becoming the preferred media
choice for our daily works such as information search, company
presentation, shopping, and so on. At the same time, we live in a
period where visual appearances play an increasingly important
role in our daily life. In spite of designers- effort to develop a web
site which be both user-friendly and attractive, it would be difficult
to ensure the outcome-s aesthetic quality, since the visual
appearance is a matter of an individual self perception and opinion.
In this study, it is attempted to develop an automatic system for
web pages aesthetic evaluation which are the building blocks of
web sites. Based on the image processing techniques and artificial
neural networks, the proposed method would be able to categorize
the input web page according to its visual appearance and aesthetic
quality. The employed features are multiscale/multidirectional
textural and perceptual color properties of the web pages, fed to
perceptron ANN which has been trained as the evaluator. The
method is tested using university web sites and the results
suggested that it would perform well in the web page aesthetic
evaluation tasks with around 90% correct categorization.
Abstract: Aldehydes as secondary lipid oxidation products are highly specific to the oxidative degradation of particular polyunsaturated fatty acids present in foods. Gas chromatographic analysis of those volatile compounds has been widely used for monitoring of the deterioration of food products. Developed static headspace gas chromatography method using flame ionization detector (SHS GC FID) was applied to monitor the aldehydes present in processed foods such as bakery, meat and confectionary products.
Five selected aldehydes were determined in samples without any sample preparation, except grinding for bakery and meat products. SHS–GC analysis allows the separation of propanal, pentanal, hexanal, heptanal and octanal, within 15min. Aldehydes were quantified in fresh and stored samples, and the obtained range of aldehydes in crackers was 1.62±0.05 – 9.95±0.05mg/kg, in sausages 6.62±0.46 – 39.16±0.39mg/kg; and in cocoa spread cream 0.48±0.01 – 1.13±0.02mg/kg. Referring to the obtained results, the following can be concluded, proposed method is suitable for different types of samples, content of aldehydes varies depending on the type of a sample, and differs in fresh and stored samples of the same type.
Abstract: The 'wind-rain' house has a courtyard with glazed
roof, which allows more direct sunlight to come into indoor spaces
during the winter. The glazed roof can be partially opened or closed
and automatically controlled to provide natural ventilation in order to
adjust for indoor thermal conditions and the roof area can be shaded
by reflective insulation materials during the summer. Two field
studies for evaluating indoor thermal conditions of the two 'windrain'
houses have been carried out by author in 2009 and 2010.
Indoor and outdoor air temperature and relative humidity adjacent to
floor and ceiling of the two sample houses were continuously tested
at 15-minute intervals, 24 hours a day during the winter months.
Based on field study data, this study investigates relationships
between building design and indoor thermal condition of the 'windrain'
house to improve the future house design for building thermal
comfort and energy efficiency
Abstract: Soft topological spaces are considered as mathematical tools for dealing with uncertainties, and a fuzzy topological space is a special case of the soft topological space. The purpose of this paper is to study soft topological spaces. We introduce some new concepts in soft topological spaces such as soft first-countable spaces, soft second-countable spaces and soft separable spaces, and some basic properties of these concepts are explored.
Abstract: Corrugated wire mesh laminates (CWML) are a class
of engineered open cell structures that have potential for applications
in many areas including aerospace and biomedical engineering. Two
different methods of fabricating corrugated wire mesh laminates from
stainless steel, one using a high temperature Lithobraze alloy and the
other using a low temperature Eutectic solder for joining the
corrugated wire meshes are described herein. Their implementation is
demonstrated by manufacturing CWML samples of 304 and 316
stainless steel (SST). It is seen that due to the facility of employing
wire meshes of different densities and wire diameters, it is possible to
create CWML laminates with a wide range of effective densities. The
fabricated laminates are tested under uniaxial compression. The
variation of the compressive yield strength with relative density of the
CWML is compared to the theory developed by Gibson and Ashby for
open cell structures [22]. It is shown that the compressive strength of
the corrugated wire mesh laminates can be described using the same
equations by using an appropriate value for the linear coefficient in the
Gibson-Ashby model.
Abstract: Segmentation in ultrasound images is challenging due to the interference from speckle noise and fuzziness of boundaries. In this paper, a segmentation scheme using fuzzy c-means (FCM) clustering incorporating both intensity and texture information of images is proposed to extract breast lesions in ultrasound images. Firstly, the nonlinear structure tensor, which can facilitate to refine the edges detected by intensity, is used to extract speckle texture. And then, a spatial FCM clustering is applied on the image feature space for segmentation. In the experiments with simulated and clinical ultrasound images, the spatial FCM clustering with both intensity and texture information gets more accurate results than the conventional FCM or spatial FCM without texture information.
Abstract: A clustering is process to identify a homogeneous
groups of object called as cluster. Clustering is one interesting topic
on data mining. A group or class behaves similarly characteristics.
This paper discusses a robust clustering process for data images with
two reduction dimension approaches; i.e. the two dimensional
principal component analysis (2DPCA) and principal component
analysis (PCA). A standard approach to overcome this problem is
dimension reduction, which transforms a high-dimensional data into
a lower-dimensional space with limited loss of information. One of
the most common forms of dimensionality reduction is the principal
components analysis (PCA). The 2DPCA is often called a variant of
principal component (PCA), the image matrices were directly treated
as 2D matrices; they do not need to be transformed into a vector so
that the covariance matrix of image can be constructed directly using
the original image matrices. The decomposed classical covariance
matrix is very sensitive to outlying observations. The objective of
paper is to compare the performance of robust minimizing vector
variance (MVV) in the two dimensional projection PCA (2DPCA)
and the PCA for clustering on an arbitrary data image when outliers
are hiden in the data set. The simulation aspects of robustness and
the illustration of clustering images are discussed in the end of
paper
Abstract: This research contribution propels the idea of collaborating environment for the execution of student satellite projects in the backdrop of project management principles. The recent past has witnessed a technological shift in the aerospace industry from the big satellite projects to the small spacecrafts especially for the earth observation and communication purposes. This vibrant shift has vitalized the academia and industry to share their resources and to create a win-win paradigm of mutual success and technological development along with the human resource development in the field of aerospace. Small student satellites are the latest jargon of academia and more than 100 CUBESAT projects have been executed successfully all over the globe and many new student satellite projects are in the development phase. The small satellite project management requires the application of specific knowledge, skills, tools and techniques to achieve the defined mission requirements. The Authors have presented the detailed outline for the project management of student satellites and presented the role of industry to collaborate with the academia to get the optimized results in academic environment.
Abstract: The Object of this paper is to design and analyze a
Hysteresis modulation based sliding mode control (HMSMC) for
positive output elementary super lift Luo converter (POESLLC),
which is the start-of-the-art DC-DC converter. The positive output
elementary super lift Luo converter performs the voltage
conversion from positive source voltage to positive load voltage.
This paper proposes a HMSMC capable of providing the good
steady state and dynamic performance compared to conventional
controllers. Dynamic equations describing the positive output
elementary super lift luo converter are derived by using state space
average method. The simulation model of the positive output
elementary super lift Luo converter with its control circuit is
implemented in Matlab/Simulink. The HMSMC for positive
output elementary super lift Luo converter is tested for line
changes, load changes and also for components variations.
Abstract: Honeycomb sandwich panels are increasingly used in the construction of space vehicles because of their outstanding strength, stiffness and light weight properties. However, the use of honeycomb sandwich plates comes with difficulties in the design process as a result of the large number of design variables involved, including composite material design, shape and geometry. Hence, this work deals with the presentation of an optimal design of hexagonal honeycomb sandwich structures subjected to space environment. The optimization process is performed using a set of algorithms including the gravitational search algorithm (GSA). Numerical results are obtained and presented for a set of algorithms. The results obtained by the GSA algorithm are much better compared to other algorithms used in this study.
Abstract: We present a visualization technique for radial drawing of trees consisting of two slightly different algorithms. Both of them make use of node-link diagrams for visual encoding. This visualization creates clear drawings without edge crossing. One of the algorithms is suitable for real-time visualization of large trees, as it requires minimal recalculation of the layout if leaves are inserted or removed from the tree; while the other algorithm makes better utilization of the drawing space. The algorithms are very similar and follow almost the same procedure but with different parameters. Both algorithms assign angular coordinates for all nodes which are then converted into 2D Cartesian coordinates for visualization. We present both algorithms and discuss how they compare to each other.
Abstract: In this paper a sliding-mode torque and flux control is
designed for encoderless synchronous reluctance motor drive. The
sliding-mode plus PI controllers are designed in the stator-flux field
oriented reference frame which is able to track the mentioned
reference signals with a minimum pulsations in the state condition. In
addition, with these controllers a fast dynamic response is also
achieved for the drive system. The proposed control scheme is robust
subject to parameters variation except to stator resistance. To solve
this problem a simple estimator is used for on-line detecting of this
parameter. Moreover, the rotor position and speed are estimated by
on-line obtaining of the stator-flux-space vector. The effectiveness
and capability of the proposed control approach is verified by both
the simulation and experimental results.
Abstract: The previous researches focused on the influence of
anthropogenic greenhouse gases exerting global warming, but not
consider whether desert sand may warm the planet, this could be
improved by accounting for sand's physical and geometric properties.
Here we show, sand particles (because of their geometry) at the desert
surface form an extended surface of up to 1 + π/4 times the planar area
of the desert that can contact sunlight, and at shallow depths of the
desert form another extended surface of at least 1 + π times the planar
area that can contact air. Based on this feature, an enhanced heat
exchange system between sunlight, desert sand, and air in the spaces
between sand particles could be built up automatically, which can
increase capture of solar energy, leading to rapid heating of the sand
particles, and then the heating of sand particles will dramatically heat
the air between sand particles. The thermodynamics of deserts may
thus have contributed to global warming, especially significant to
future global warming if the current desertification continues to
expand.
Abstract: This paper presents the automated methods employed
for extracting craniofacial landmarks in white light images as part of
a registration framework designed to support three neurosurgical
procedures. The intraoperative space is characterised by white light
stereo imaging while the preoperative plan is performed on CT scans.
The registration aims at aligning these two modalities to provide a
calibrated environment to enable image-guided solutions. The
neurosurgical procedures can then be carried out by mapping the
entry and target points from CT space onto the patient-s space. The
registration basis adopted consists of natural landmarks (eye corner
and ear tragus). A 5mm accuracy is deemed sufficient for these three
procedures and the validity of the selected registration basis in
achieving this accuracy has been assessed by simulation studies. The
registration protocol is briefly described, followed by a presentation
of the automated techniques developed for the extraction of the
craniofacial features and results obtained from tests on the AR and
FERET databases. Since the three targeted neurosurgical procedures
are routinely used for head injury management, the effect of
bruised/swollen faces on the automated algorithms is assessed. A
user-interactive method is proposed to deal with such unpredictable
circumstances.