Abstract: In this paper a new method for increasing the speed of
SAGCM-APD is proposed. Utilizing carrier rate equations in
different regions of the structure, a circuit model for the structure is
obtained. In this research, in addition to frequency response, the
effect of added new charge layer on some transient parameters like
slew-rate, rising and falling times have been considered. Finally, by
trading-off among some physical parameters such as different layers
widths and droppings, a noticeable decrease in breakdown voltage
has been achieved. The results of simulation, illustrate some features
of proposed structure improvement in comparison with conventional
SAGCM-APD structures.
Abstract: A 10bit, 40 MSps, sample and hold, implemented in 0.18-μm CMOS technology with 3.3V supply, is presented for application in the front-end stage of an analog-to-digital converter. Topology selection, biasing, compensation and common mode feedback are discussed. Cascode technique has been used to increase the dc gain. The proposed opamp provides 149MHz unity-gain bandwidth (wu), 80 degree phase margin and a differential peak to peak output swing more than 2.5v. The circuit has 55db Total Harmonic Distortion (THD), using the improved fully differential two stage operational amplifier of 91.7dB gain. The power dissipation of the designed sample and hold is 4.7mw. The designed system demonstrates relatively suitable response in different process, temperature and supply corners (PVT corners).
Abstract: This paper describes a CMOS four-quadrant
multiplier intended for use in the front-end receiver by utilizing the
square-law characteristic of the MOS transistor in the saturation
region. The circuit is based on 0.35 um CMOS technology simulated
using HSPICE software. The mixer has a third-order inter the power
consumption is 271uW from a single 1.2V power supply. One of the
features of the proposed design is using two MOS transistors
limitation to reduce the supply voltage, which leads to reduce the
power consumption. This technique provides a GHz bandwidth
response and low power consumption.
Abstract: This investigation examines the effect of the sintering
temperature curve in manufactured nickel powder capillary structure
(wick) for a loop heat pipe (LHP). The sintering temperature curve is
composed of a region of increasing temperature; a region of constant
temperature and a region of declining temperature. The most important
region is that in which the temperature increases, as an index in the
stage in which the temperature increases. The wick of nickel powder is
manufactured in the stage of fixed sintering temperature and the time
between the stage of constant temperature and the stage of falling
temperature. When the slope of the curve in the region of increasing
temperature is unity (equivalent to 10 °C/min), the structure of the
wick is complete and the heat transfer performance is optimal. The
result of experiment test demonstrates that the heat transfer
performance is optimal at 320W; the minimal total thermal resistance
is approximately 0.18°C/W, and the heat flux is 17W/cm2; the internal
parameters of the wick are an effective pore radius of 3.1 μm, a
permeability of 3.25×10-13m2 and a porosity of 71%.
Abstract: In the present work we model a Multiquantum Well
structure Separate Absorption and Charge Multiplication Avalanche
Photodiode (MQW-SACM-APD), while the Absorption region
coincide with the MQW. We consider the nonuniformity of electric
field using split-step method in active region. This model is based on
the carrier rate equations in the different regions of the device. Using
the model we obtain the photocurrent, and dark current. As an
example, InGaAs/InP SACM-APD and MQW-SACM-APD are
simulated. There is a good agreement between the simulation and
experimental results.
Abstract: This paper presented a modified efficient inductive
powering link based on ASK modulator and proposed efficient class-
E power amplifier. The design presents the external part which is
located outside the body to transfer power and data to the implanted
devices such as implanted Microsystems to stimulate and monitoring
the nerves and muscles. The system operated with low band
frequency 10MHZ according to industrial- scientific – medical (ISM)
band to avoid the tissue heating. For external part, the modulation
index is 11.1% and the modulation rate 7.2% with data rate 1 Mbit/s
assuming Tbit = 1us. The system has been designed using 0.35-μm
fabricated CMOS technology. The mathematical model is given and
the design is simulated using OrCAD P Spice 16.2 software tool and
for real-time simulation, the electronic workbench MULISIM 11 has
been used.
Abstract: This paper presents a new circuit arrangement for a
current-mode Wheatstone bridge that is suitable for low-voltage
integrated circuits implementation. Compared to the other proposed
circuits, this circuit features severe reduction of the elements number,
low supply voltage (1V) and low power consumption (
Abstract: The present work is concerned with the effect of turning process parameters (cutting speed, feed rate, and depth of cut) and distance from the center of work piece as input variables on the chip micro-hardness as response or output. Three experiments were conducted; they were used to investigate the chip micro-hardness behavior at diameter of work piece for 30[mm], 40[mm], and 50[mm]. Response surface methodology (R.S.M) is used to determine and present the cause and effect of the relationship between true mean response and input control variables influencing the response as a two or three dimensional hyper surface. R.S.M has been used for designing a three factor with five level central composite rotatable factors design in order to construct statistical models capable of accurate prediction of responses. The results obtained showed that the application of R.S.M can predict the effect of machining parameters on chip micro-hardness. The five level factorial designs can be employed easily for developing statistical models to predict chip micro-hardness by controllable machining parameters. Results obtained showed that the combined effect of cutting speed at it?s lower level, feed rate and depth of cut at their higher values, and larger work piece diameter can result increasing chi micro-hardness.
Abstract: The study and development of an innovative material
for building insulation is really important for a sustainable society in order to improve comfort and reducing energy consumption. The aim of this work is the development of insulating panels for
sustainable buildings based on an innovative material made by
cardboard and Phase Change Materials (PCMs).
The research has consisted in laboratory tests whose purpose has been the obtaining of the required properties for insulation panels: lightweight, porous structures and mechanical resistance. PCMs have been used for many years in the building industry as
smart insulation technology because of their properties of storage and release high quantity of latent heat at useful specific temperatures [1]- [2].
The integration of PCMs into cellulose matrix during the waste paper recycling process has been developed in order to obtain a
composite material.
Experiments on the productive process for the realization of insulating panels were done in order to make the new material
suitable for building application. The addition of rising agents
demonstrated the possibility to obtain a lighter structure with better
insulation properties.
Several tests were conducted to verify the new panel properties. The results obtained have shown the possibility to realize an
innovative and sustainable material suitable to replace insulating panels currently used.
Abstract: One of the main processes of supply chain
management is supplier selection process which its accurate
implementation can dramatically increase company competitiveness.
In presented article model developed based on the features of
second tiers suppliers and four scenarios are predicted in order to
help the decision maker (DM) in making up his/her mind. In addition
two tiers of suppliers have been considered as a chain of suppliers.
Then the proposed approach is solved by a method combined of
concepts of fuzzy set theory (FST) and linear programming (LP)
which has been nourished by real data extracted from an engineering
design and supplying parts company. At the end results reveal the
high importance of considering second tier suppliers features as
criteria for selecting the best supplier.
Abstract: A Rotary Disc Contactor with inner diameter of
9.1cm and maximum operating height of 40cm has been used to
investigate break up phenomenon. Water-Toluene, Water as
continuous phase and Toluene as dispersed phase, was selected as
chemical system in the experiments. The mentioned chemical system
has high interfacial tension so it was possible to form big drops
which permit accurate investigation on break up phenomenon as well
as the first and second critical rotor speeds.
In this study, Break up phenomenon has been studied as a function
of mother drop size, rotor speed and continuous phase height. Further
more; the effects of mother drop size and continuous phase height on
the first and second critical rotor speeds were investigated. Finally,
two modified correlations were proposed to estimate the first and
second critical speeds.
Abstract: The experiment was conducted to evaluate
digestibility quantities of protein in Canola Meals (CMs) between
caecectomised and intact adult Rhode Island Red (RIR) cockerels
with using conventional addition method (CAM) for 7 d: a 4-d
adaptation and a 3-d experiment period on the basis of a completely
randomized design with 4 replicates. Results indicated that
caecectomy decreased (P
Abstract: In this paper, we present a vertical nanowire thin film transistor with gate-all-around architecture, fabricated using CMOS compatible processes. A novel method of fabricating polysilicon vertical nanowires of diameter as small as 30 nm using wet-etch is presented. Both n-type and p-type vertical poly-silicon nanowire transistors exhibit superior electrical characteristics as compared to planar devices. On a poly-crystalline nanowire of 30 nm diameter, high Ion/Ioff ratio of 106, low drain-induced barrier lowering (DIBL) of 50 mV/V, and low sub-threshold slope SS~100mV/dec are demonstrated for a device with channel length of 100 nm.
Abstract: The fundamental objective of the university is to
genuinely provide a higher education to mankind and society. Higher
education institutions earn billions of dollars in research funds, granted
by national government or related institutions, which literally came
from taxpayers. Everyday universities consume those grants; in return,
provide society with a human resource and research developments.
However, not all taxpayers have their major concerns on those
researches, other than that they are more curiously to see the project
being build tangibly and evidently to certify what they pay for. This
paper introduces the concept of University – Community Business
Continuity Management for Disaster – Resilient City, which modified
the concept of Business Continuity Management (BCM) toward
university community to create advancing collaboration leading to the
disaster – resilient community and city. This paper focuses on
describing in details the backgrounds and principles of the concept and
discussing the advantages and limitations of the concept.
Abstract: A 1V, 1GHz low noise amplifier (LNA) has been designed and simulated using Spectre simulator in a standard TSMC 0.18um CMOS technology.With low power and noise optimization techniques, the amplifier provides a gain of 24 dB, a noise figure of only 1.2 dB, power dissipation of 14 mW from a 1 V power supply.
Abstract: We present a white LED-based optical wireless
communication systems for indoor ubiquitous sensor networks. Each
sensor node could access to the server through the PLC (Power Line
Communication)-Ethernet interface. The proposed system offers a
full-duplex wireless link by using different wavelengths to reduce the
inter-symbol interference between uplink and downlink. Through the
1-to-n optical wireless sensor network and PLC modem, the mobile
terminals send a temperature data to server. The data transmission
speed and distance are 115.2kbps and about 60cm, respectively.
Abstract: This paper presents the design and implementation of a fully integrated transimpedance amplifier (TIA) as the analog frontend receiver for Capacitive Micromachined Ultrasound Transducers (CMUTs) for ultrasound biomicroscope imaging application. The amplifier is designed to amplify the received signals from 17.5MHz to 52.5MHz with a center frequency of 35MHz. The TIA was fabricated in GF 0.18μm 1P6M 30V high voltage process. The measurement results show that the designed amplifier can reach a transimpedance gain of 61.08dBΩ and operating frequency from 17.5MHz to 100MHz with 1VP-P output voltage under 6V power supply.
Abstract: This paper considers a multi criteria cell formation
problem in Cellular Manufacturing System (CMS). Minimizing the
number of voids and exceptional elements in cells simultaneously are
two proposed objective functions. This problem is an Np-hard
problem according to the literature, and therefore, we can-t find the
optimal solution by an exact method. In this paper we developed two
ant algorithms, Ant Colony Optimization (ACO) and Max-Min Ant
System (MMAS), based on Data Envelopment Analysis (DEA). Both
of them try to find the efficient solutions based on efficiency concept
in DEA. Each artificial ant is considered as a Decision Making Unit
(DMU). For each DMU we considered two inputs, the values of
objective functions, and one output, the value of one for all of them.
In order to evaluate performance of proposed methods we provided
an experimental design with some empirical problem in three
different sizes, small, medium and large. We defined three different
criteria that show which algorithm has the best performance.
Abstract: As chip manufacturing technology is suddenly on the
threshold of major evaluation, which shrinks chip in size and
performance, LFSR (Linear Feedback Shift Register) is implemented
in layout level which develops the low power consumption chip,
using recent CMOS, sub-micrometer layout tools. Thus LFSR
counter can be a new trend setter in cryptography and is also
beneficial as compared to GRAY & BINARY counter and variety of
other applications.
This paper compares 3 architectures in terms of the hardware
implementation, CMOS layout and power consumption, using
Microwind CMOS layout tool. Thus it provides solution to a low
power architecture implementation of LFSR in CMOS VLSI.
Abstract: All the available algorithms for blind estimation namely constant modulus algorithm (CMA), Decision-Directed Algorithm (DDA/DFE) suffer from the problem of convergence to local minima. Also, if the channel drifts considerably, any DDA looses track of the channel. So, their usage is limited in varying channel conditions. The primary limitation in such cases is the requirement of certain overhead bits in the transmit framework which leads to wasteful use of the bandwidth. Also such arrangements fail to use channel state information (CSI) which is an important aid in improving the quality of reception. In this work, the main objective is to reduce the overhead imposed by the pilot symbols, which in effect reduces the system throughput. Also we formulate an arrangement based on certain dynamic Artificial Neural Network (ANN) topologies which not only contributes towards the lowering of the overhead but also facilitates the use of the CSI. A 2×2 Multiple Input Multiple Output (MIMO) system is simulated and the performance variation with different channel estimation schemes are evaluated. A new semi blind approach based on dynamic ANN is proposed for channel tracking in varying channel conditions and the performance is compared with perfectly known CSI and least square (LS) based estimation.