Abstract: Power line channel is proposed as an alternative for broadband data transmission especially in developing countries like Tanzania [1]. However the channel is affected by stochastic attenuation and deep notches which can lead to the limitation of channel capacity and achievable data rate. Various studies have characterized the channel without giving exactly the maximum performance and limitation in data transfer rate may be this is due to complexity of channel modeling being used. In this paper the channel performance of medium voltage, low voltage and indoor power line channel is presented. In the investigations orthogonal frequency division multiplexing (OFDM) with phase shift keying (PSK) as carrier modulation schemes is considered, for indoor, medium and low voltage channels with typical ten branches and also Golay coding is applied for medium voltage channel. From channels, frequency response deep notches are observed in various frequencies which can lead to reduce the achievable data rate. However, is observed that data rate up to 240Mbps is realized for a signal to noise ratio of about 50dB for indoor and low voltage channels, however for medium voltage a typical link with ten branches is affected by strong multipath and coding is required for feasible broadband data transfer.
Abstract: Heavy metal transfer in soil profiles is a major
environmental concern because even slow transport through the soil
may eventually lead to deterioration of groundwater quality. The use
of sewage sludge and effluents from wastewater treatment plants for
irrigation of agricultural lands is on the rise particularly in peri-urban
area of developing countries. In this study soil samples under sludge
application and wastewater irrigation were studied and soil samples
were collected in the soil profiles from the surface to 100 cm in
depth. For this purpose, three plots were made in a treatment plant in
south of Tehran-Iran. First plot was irrigated just with effluent from
wastewater treatment plant, second plot with simulated heavy metals
concentration equal 50 years irrigation and in third plot sewage
sludge and effluent was used. Trace metals concentration (Cd, Cu)
were determined for soil samples. The results indicate movement of
metals was observed, but the most concentration of metals was found
in topsoil samples. The most of Cadmium concentration was
measured in the topsoil of plot 3, 4.5mg/kg and Maximum cadmium
movement was observed in 0-20 cm. The most concentration of
copper was 27.76mg/kg, and maximum percolation in 0-20 cm.
Metals (Cd, Cu) were measured in leached water. Preferential flow
and metal complexation with soluble organic apparently allow
leaching of heavy metals.
Abstract: This paper deals with infinite time horizon fuzzy Economic Order Quantity (EOQ) models for deteriorating items with
stock dependent demand rate and nonlinear holding costs by taking deterioration rate θ0 as a triangular fuzzy number (θ0 −δ 1, θ0, θ0 +δ 2), where 1 2 0 0
Abstract: Accurate software cost estimates are critical to both
developers and customers. They can be used for generating request
for proposals, contract negotiations, scheduling, monitoring and
control. The exact relationship between the attributes of the effort
estimation is difficult to establish. A neural network is good at
discovering relationships and pattern in the data. So, in this paper a
comparative analysis among existing Halstead Model, Walston-Felix
Model, Bailey-Basili Model, Doty Model and Neural Network
Based Model is performed. Neural Network has outperformed the
other considered models. Hence, we proposed Neural Network
system as a soft computing approach to model the effort estimation
of the software systems.
Abstract: In this paper, we propose a method for detecting
circular shapes with subpixel accuracy. First, the geometric properties
of circles have been used to find the diameters as well as the
circumference pixels. The center and radius are then estimated by the
circumference pixels. Both synthetic and real images have been tested
by the proposed method. The experimental results show that the new
method is efficient.
Abstract: Increasing attention has been given in academia to the concept of corporate social responsibility. Also, the number of companies that undertake social responsibility initiatives has been boosting day by day since behaving in a socially responsible manner brings a lot to the companies. Literature provides various benefits of social responsibility and under which situations these benefits could be realized. However, most of these studies focus on one aspect of the consequences of behaving in a socially responsible manner and there is no study that unifies the conditions that a company should fulfill to make customers prefer its brand. This study aims to fill this gap. More specifically, the purpose of this study is to identify the conditions that a socially responsible company should fulfill in order to attract customers. To this end, a scale is developed and its reliability and validity is assessed through the method of Multitrait- Multimethod Matrix.
Abstract: In this paper effects of inclination angle on natural
convection flow in an open cavity has been analyzed with Lattice
Boltzmann Method (LBM).The angle of inclination varied from θ= -
45° to 45° with 15° intervals. Study has been conducted for Rayleigh
numbers (Ra) 104 to 106. The comparisons show that the average
Nusselt number increases with growth of Rayleigh number and the
average Nusselt number increase as inclination angles increases at
Ra=104.At Ra=105 and Ra=106 the average Nusselt number enhance
as inclination angels varied from θ= -45° to θ= 0° and decrease as
inclination angels increase in θ= 0° to θ= 45°.
Abstract: The main purpose of this study is to analyze climbers
involved in motivation and risk perception and analysis of the
predictive ability of the risk perception "mountaineering" involved in
motivation. This study used questionnaires, to have to climb the
3000m high mountain in Taiwan climbers object to carry out an
investigation in order to non-random sampling, a total of 231 valid
questionnaires were. After statistical analysis, the study found that: 1.
Climbers the highest climbers involved in motivation "to enjoy the
natural beauty of the fun. 2 climbers for climbers "risk perception" the
highest: the natural environment of risk. 3. Climbers “seeking
adventure stimulate", “competence achievement" motivation highly
predictive of risk perception. Based on these findings, this study not
only practices the recommendations of the outdoor leisure industry,
and also related research proposals for future researchers.
Abstract: Because of the requirement for low sulfur content of
fuel oils, it is necessary to develop alternative methods for desulfurization of heavy fuel oil. Due to the disadvantages of HDS
technologies such as costs, safety and green environment, new
methods have been developed. Among these methods is ultrasoundassisted
oxidative desulfurization. Using ultrasound-assisted
oxidative desulfurization, compounds such as benzothiophene and
dibenzothiophene can be oxidized. As an alternative method is sulfur
elimination of heavy fuel oil by using of activated carbon in a packed column in batch condition. The removal of sulfur compounds in this
case to reach about 99%. The most important property of activated carbon is ability of it for adsorption, which is due to high surface area
and pore volume of it.
Abstract: Many advanced Routing protocols for wireless sensor networks have been implemented for the effective routing of data. Energy awareness is an essential design issue and almost all of these routing protocols are considered as energy efficient and its ultimate objective is to maximize the whole network lifetime. However, the introductions of video and imaging sensors have posed additional challenges. Transmission of video and imaging data requires both energy and QoS aware routing in order to ensure efficient usage of the sensors and effective access to the gathered measurements. In this paper, the performance of the energy-aware QoS routing Protocol are analyzed in different performance metrics like average lifetime of a node, average delay per packet and network throughput. The parameters considered in this study are end-to-end delay, real time data generation/capture rates, packet drop probability and buffer size. The network throughput for realtime and non-realtime data was also has been analyzed. The simulation has been done in NS2 simulation environment and the simulation results were analyzed with respect to different metrics.
Abstract: Due to the constant increase in the volume of information available to applications in fields varying from medical diagnosis to web search engines, accurate support of similarity becomes an important task. This is also the case of spam filtering techniques where the similarities between the known and incoming messages are the fundaments of making the spam/not spam decision. We present a novel approach to filtering based solely on layout, whose goal is not only to correctly identify spam, but also warn about major emerging threats. We propose a mathematical formulation of the email message layout and based on it we elaborate an algorithm to separate different types of emails and find the new, numerically relevant spam types.
Abstract: Microplasma welding is a less expensive alternative to
laser welding in dental technology. The aim of the study was to
highlight discontinuities present in the microplasma welded joints of
dental base metal alloys by visual analysis. Five base metal alloys
designated for fixed prostheses manufacture were selected for the
experiments. Using these plates, preliminary tests were conducted by
microplasma welding in butt joint configuration, without filler
material, bilaterally and with filler material, proper for each base
metal. Macroscopic visual inspection was performed to assess
carefully the irregularities in the welds. Electron microscopy allowed
detection of discontinuities that are not visible to the eye and
revealing details regarding location, trajectory, morphology and size
of discontinuities. Supplementing visual control with microscopic
analysis allows to detect small discontinuities, which escapes the
macroscopic control and to make a detailed study of the weld.
Abstract: We present the induced generalized hybrid
averaging (IGHA) operator. It is a new aggregation operator
that generalizes the hybrid averaging (HA) by using
generalized means and order inducing variables. With this
formulation, we get a wide range of mean operators such as
the induced HA (IHA), the induced hybrid quadratic
averaging (IHQA), the HA, etc. The ordered weighted
averaging (OWA) operator and the weighted average (WA)
are included as special cases of the HA operator. Therefore,
with this generalization we can obtain a wide range of
aggregation operators such as the induced generalized OWA
(IGOWA), the generalized OWA (GOWA), etc. We further
generalize the IGHA operator by using quasi-arithmetic
means. Then, we get the Quasi-IHA operator. Finally, we also
develop an illustrative example of the new approach in a
financial decision making problem. The main advantage of the
IGHA is that it gives a more complete view of the decision
problem to the decision maker because it considers a wide
range of situations depending on the operator used.
Abstract: The purpose of this paper is to propose a text mining
approach to evaluate companies- practices on affective management.
Affective management argues that it is critical to take stakeholders-
affects into consideration during decision-making process, along with
the traditional numerical and rational indices. CSR reports published
by companies were collected as source information. Indices were
proposed based on the frequency and collocation of words relevant to
affective management concept using text mining approach to analyze
the text information of CSR reports. In addition, the relationships
between the results obtained using proposed indices and traditional
indicators of business performance were investigated using
correlation analysis. Those correlations were also compared between
manufacturing and non-manufacturing companies. The results of this
study revealed the possibility to evaluate affective management
practices of companies based on publicly available text documents.
Abstract: This paper considers the benefits gained by using an
efficient quality of service management such as DiffServ technique to
improve the performance of military communications. Low delay and
no blockage must be achieved especially for real time tactical data.
All traffic flows generated by different applications do not need same
bandwidth, same latency, same error ratio and this scalable technique
of packet management based on priority levels is analysed. End to
end architectures supporting various traffic flows and including lowbandwidth
and high-delay HF or SHF military links as well as
unprotected Internet sub domains are studied. A tuning of Diffserv
parameters is proposed in accordance with different loads of various
traffic and different operational situations.
Abstract: The African Great Lakes Region refers to the zone
around lakes Victoria, Tanganyika, Albert, Edward, Kivu, and
Malawi. The main source of electricity in this region is hydropower
whose systems are generally characterized by relatively weak,
isolated power schemes, poor maintenance and technical deficiencies
with limited electricity infrastructures. Most of the hydro sources are
rain fed, and as such there is normally a deficiency of water during
the dry seasons and extended droughts. In such calamities fossil fuels
sources, in particular petroleum products and natural gas, are
normally used to rescue the situation but apart from them being nonrenewable,
they also release huge amount of green house gases to our
environment which in turn accelerates the global warming that has at
present reached an amazing stage. Wind power is ample, renewable,
widely distributed, clean, and free energy source that does not
consume or pollute water. Wind generated electricity is one of the
most practical and commercially viable option for grid quality and
utility scale electricity production. However, the main shortcoming
associated with electric wind power generation is fluctuation in its
output both in space and time. Before making a decision to establish
a wind park at a site, the wind speed features there should therefore
be known thoroughly as well as local demand or transmission
capacity. The main objective of this paper is to utilise monthly
average wind speed data collected from one prospective site within
the African Great Lakes Region to demonstrate that the available
wind power there is high enough to generate electricity. The mean
monthly values were calculated from records gathered on hourly
basis for a period of 5 years (2001 to 2005) from a site in Tanzania.
The documentations that were collected at a height of 2 m were
projected to a height of 50 m which is the standard hub height of
wind turbines. The overall monthly average wind speed was found to
be 12.11 m/s whereas June to November was established to be the
windy season as the wind speed during the session is above the
overall monthly wind speed. The available wind power density
corresponding to the overall mean monthly wind speed was evaluated
to be 1072 W/m2, a potential that is worthwhile harvesting for the
purpose of electric generation.
Abstract: Diesel Engines emit complex mixtures of inorganic
and organic compounds in the form of both solid and vapour phase
particles. Most of the particulates released are ultrafine nanoparticles
which are detrimental to human health and can easily enter the body
by respiration. The emissions standards on particulate matter release
from diesel engines are constantly upgraded within the European
Union and with future regulations based on the particles numbers
released instead of merely mass, the need for effective aftertreatment
devices will increase. Standard particulate filters in the form of wall
flow filters can have problems with high soot accumulation,
producing a large exhaust backpressure. A potential solution would
be to combine the standard filter with a flow through filter to reduce
the load on the wall flow filter. In this paper soot particle trapping has
been simulated in different continuous flow filters of monolithic
structure including the use of promoters, at laminar flow conditions.
An Euler Lagrange model, the discrete phase model in Ansys used
with user defined functions for forces acting on particles. A method
to quickly screen trapping of 5 nm and 10 nm particles in different
catalysts designs with tracers was also developed.
Simulations of square duct monoliths with promoters show that the
strength of the vortices produced are not enough to give a high
amount of particle deposition on the catalyst walls. The smallest
particles in the simulations, 5 and 10 nm particles were trapped to a
higher extent, than larger particles up to 1000 nm, in all studied
geometries with the predominant deposition mechanism being
Brownian diffusion. The comparison of the different filters designed
with a wall flow filter does show that the options for altering a design
of a flow through filter, without imposing a too large pressure drop
penalty are good.
Abstract: A new approach to predict the 3D structures of proteins by combining the knowledge-based method and Molecular Dynamics Simulation is presented on the chicken villin headpiece subdomain (HP-36). Comparative modeling is employed as the knowledge-based method to predict the core region (Ala9-Asn28) of the protein while the remaining residues are built as extended regions (Met1-Lys8; Leu29-Phe36) which then further refined using Molecular Dynamics Simulation for 120 ns. Since the core region is built based on a high sequence identity to the template (65%) resulting in RMSD of 1.39 Å from the native, it is believed that this well-developed core region can act as a 'nucleation center' for subsequent rapid downhill folding. Results also demonstrate that the formation of the non-native contact which tends to hamper folding rate can be avoided. The best 3D model that exhibits most of the native characteristics is identified using clustering method which then further ranked based on the conformational free energies. It is found that the backbone RMSD of the best model compared to the NMR-MDavg is 1.01 Å and 3.53 Å, for the core region and the complete protein, respectively. In addition to this, the conformational free energy of the best model is lower by 5.85 kcal/mol as compared to the NMR-MDavg. This structure prediction protocol is shown to be effective in predicting the 3D structure of small globular protein with a considerable accuracy in much shorter time compared to the conventional Molecular Dynamics simulation alone.
Abstract: Advances in processors architecture, such as multicore,
increase the size of complexity of parallel computer systems.
With multi-core architecture there are different parallel languages
that can be used to run parallel programs. One of these languages is
OpenMP which embedded in C/Cµ or FORTRAN. Because of this
new architecture and the complexity, it is very important to evaluate
the performance of OpenMP constructs, kernels, and application
program on multi-core systems. Performance is the activity of
collecting the information about the execution characteristics of a
program. Performance tools consists of at least three interfacing
software layers, including instrumentation, measurement, and
analysis. The instrumentation layer defines the measured
performance events. The measurement layer determines what
performance event is actually captured and how it is measured by the
tool. The analysis layer processes the performance data and
summarizes it into a form that can be displayed in performance tools.
In this paper, a number of OpenMP performance tools are surveyed,
explaining how each is used to collect, analyse, and display data
collection.
Abstract: Multicarrier transmission system such as Orthogonal
Frequency Division Multiplexing (OFDM) is a promising technique
for high bit rate transmission in wireless communication systems.
OFDM is a spectrally efficient modulation technique that can achieve
high speed data transmission over multipath fading channels without
the need for powerful equalization techniques. A major drawback
of OFDM is the high Peak-to-Average Power Ratio (PAPR) of the
transmit signal which can significantly impact the performance of the
power amplifier. In this paper we have compared the PAPR reduction
performance of Golay and Reed-Muller coded OFDM signal. From
our simulation it has been found that the PAPR reduction performance
of Golay coded OFDM is better than the Reed-Muller coded OFDM
signal. Moreover, for the optimum PAPR reduction performance, code
configuration for Golay and Reed-Muller codes has been identified.