Abstract: ORC (Organic Rankine Cycle) has potential of
reducing consumption of fossil fuels and has many favorable
characteristics to exploit low-temperature heat sources. In this work
thermodynamic performance of ORC with regeneration is
comparatively assessed for various working fluids. Special attention is
paid to the effects of system parameters such as the turbine inlet
pressure on the characteristics of the system such as net work
production, heat input, volumetric flow rate per 1 MW of net work and
quality of the working fluid at turbine exit as well as thermal
efficiency. Results show that for a given source the thermal efficiency
generally increases with increasing of the turbine inlet pressure
however has optimal condition for working fluids of low critical
pressure such as iso-pentane or n-pentane.
Abstract: The scale dependence of the strength of virtually homogeneous rock is usually considered to be insignificant but the spectrum of discontinuities plays a very important role for the strength of differently sized rock elements and also controls the rock creep strain. Large-scale load tests comprised recording of the creep strain rate that was found to be strongly retarded and negligible for stresses lower than about 1/3 of the failure load. For higher stresses creep took place according to a log time law representing secondary creep that ultimately changed to tertiary creep and failure.
Abstract: Psoriasis is a widespread skin disease affecting up to 2% population with plaque psoriasis accounting to about 80%. It can be identified as a red lesion and for the higher severity the lesion is usually covered with rough scale. Psoriasis Area Severity Index (PASI) scoring is the gold standard method for measuring psoriasis severity. Scaliness is one of PASI parameter that needs to be quantified in PASI scoring. Surface roughness of lesion can be used as a scaliness feature, since existing scale on lesion surface makes the lesion rougher. The dermatologist usually assesses the severity through their tactile sense, therefore direct contact between doctor and patient is required. The problem is the doctor may not assess the lesion objectively. In this paper, a digital image analysis technique is developed to objectively determine the scaliness of the psoriasis lesion and provide the PASI scaliness score. Psoriasis lesion is modelled by a rough surface. The rough surface is created by superimposing a smooth average (curve) surface with a triangular waveform. For roughness determination, a polynomial surface fitting is used to estimate average surface followed by a subtraction between rough and average surface to give elevation surface (surface deviations). Roughness index is calculated by using average roughness equation to the height map matrix. The roughness algorithm has been tested to 444 lesion models. From roughness validation result, only 6 models can not be accepted (percentage error is greater than 10%). These errors occur due the scanned image quality. Roughness algorithm is validated for roughness measurement on abrasive papers at flat surface. The Pearson-s correlation coefficient of grade value (G) of abrasive paper and Ra is -0.9488, its shows there is a strong relation between G and Ra. The algorithm needs to be improved by surface filtering, especially to overcome a problem with noisy data.
Abstract: Drought is one of the most important natural disasters which is probable to occur in all regions with completely different climates and in addition to causing death. It results in many economic losses and social consequences. For this reason. Studying the effects and losses caused by drought which include limitation or shortage of agricultural and drinking water resources. Decreased rainfall and increased evapotranspiration. Limited plant growth and decreased agricultural products. Especially those of dry-farming. Lower levels of surface and ground waters and increased immigrations. Etc. in the country is statistical period (1988-2007) for six stations in Roudbar town were used for statistical analysis and calculating humid and dry years. The dependable rainfall index (DRI) was the main method used in this research. Results showed that during the said statistical period and also during the years 1996-1998 and 2007. more than half of the stations had faced drought. With consideration of the conducted studies. Drawing diagrams and comparing the available data with those of dry and humid years it was found that drought affected agricultural products (e.g.olive) in a way that during the year 1996 1996 drought. Olive groves of Roudbar suffered the greatest damages. Whereupon about 70% of the crops were lost.
Abstract: A study of various turbulent inflow generation methods
was performed to compare their relative effectiveness for LES
computations of turbulent boundary layers. This study confirmed
the quality of the turbulent information produced by the family of
recycling and rescaling methods which take information from within
the computational domain. Furthermore, more general inflow methods
also proved applicable to such simulations, with a precursor-like
inflow and a random inflow augmented with forcing planes showing
promising results.
Abstract: The basis of this paper is the assumption, that graviton
is a measurable entity of molecular gravitational acceleration and this
is not a hypothetical entity. The adoption of this assumption as an
axiom is tantamount to fully opening the previously locked door to
the boundary theory between laminar and turbulent flows. It leads to
the theorem, that the division of flows of Newtonian (viscous) fluids
into laminar and turbulent is true only, if the fluid is influenced by a
powerful, external force field. The mathematical interpretation of this
theorem, presented in this paper shows, that the boundary between
laminar and turbulent flow can be determined theoretically. This is a
novelty, because thus far the said boundary was determined
empirically only and the reasons for its existence were unknown.
Abstract: The flow field in a centrifugal fan is highly complex
with flow reversal taking place on the suction side of impeller and
diffuser vanes. Generally performance of the centrifugal fan could be
enhanced by judiciously introducing splitter vanes so as to improve
the diffusion process. An extensive numerical whole field analysis on
the effect of splitter vanes placed in discrete regions of suspected
separation points is possible using CFD. This paper examines the
effect of splitter vanes corresponding to various geometrical
locations on the impeller and diffuser. The analysis shows that the
splitter vanes located near the diffuser exit improves the static
pressure recovery across the diffusing domain to a larger extent. Also
it is found that splitter vanes located at the impeller trailing edge and
diffuser leading edge at the mid-span of the circumferential distance
between the blades show a marginal improvement in the static
pressure recovery across the fan. However, splitters provided near to
the suction side of the impeller trailing edge (25% of the
circumferential gap between the impeller blades towards the suction
side), adversely affect the static pressure recovery of the fan.
Abstract: This paper studies the design of a simple constellation
precoding for a multiple-input multiple-output orthogonal frequency
division multiplexing (MIMO-OFDM) system over Rayleigh fading
channels where OFDM is used to keep the diversity replicas orthogonal
and reduce ISI effects. A multi-user environment with K synchronous
co-channel users is considered. The proposed scheme provides
a bandwidth efficient transmission for individual users by increasing
the system throughput. In comparison with the existing coded
MIMO-OFDM schemes, the precoding technique is designed under
the consideration of its low implementation complexity while providing
a comparable error performance to the existing schemes.
Analytic and simulation results have been presented to show the distinguished
error performance.
Abstract: Green incentives are included in the “American
Recovery and Reinvestment Act of 2009" (ARRA). It is, however,
unclear how these government incentives can be carried out most
effectively according to market-based principles and if they can serve
as a catalyst for an accelerated green transformation and an ultimate
solution to the current U.S. and global economic and financial crisis.
The article will compare the existing U.S. green economic policies
with those in Germany, identify problems, and suggest improvements
to allow the green stimulus incentives to achieve the best results in
the process of an accelerated green transformation. The author argues
that the current U.S. green stimulus incentives can only be most
successful if they are carried out as part of a visionary,
comprehensive, long-term, and consistent strategy of the green
economic transformation.
Abstract: This paper presents a simple and original method for
the generation of short monocycle pulses based on the transient
response of a passive band-pass filter. The recorded sub-nanosecond
pulses show a good symmetry and a small ringing (13 % of the peak
amplitude). Their spectral density covers the range 3.1 GHz to
10.6 GHz. The possibility to adapt the pulse spectral density to the
indoor FCC frequency mask is demonstrated with a prototype
working at a reduced frequency (FCC/1000). A detection technique is
proposed.
Abstract: In this work Membrane Distillation is applied to
concentrate orange Juice. Clarified orange juice (11o Brix) obtained
from fresh fruits and a sugar solution was subjected to membrane
distillation. The experiments were performed on a flat sheet module
using orange juice and sucrose solution as feeds. The concentration
of a sucrose solution, used as a model fruit juice and also orange
juice, was carried out in a direct contact membrane distillation using
hydrophobic PTFE membrane of pore size 0.2 μm and porosity 70%.
Surface modification of PTFE membrane has been carried out by
treating membrane with alcohol and water solution to make it
hydrophilic and then hydrophobicity was regained by drying. The
influences of the feed temperature, feed concentration, flow rate,
operating time on the permeate flux were studied for treated and non
treated membrane. In this work treated and non treated membrane
were compared in terms of water flux, Within the tested range, MD
with surface modified membrane the water flux has been
significantly improved by treating the membrane surface.
Abstract: In this work, stationary hot-wire measurements are
carried out to investigate the characteristics of a round free jet in its
potential core region (0 ≤ x/d ≤ 10). Measurements are carried out on
an incompressible round jet for a range of Reynolds numbers from
4000 to 8000, calculated based on the jet exit mean velocity and the
nozzle diameter. The effect of flow velocity on the development
characteristics of the jet in the core region is analyzed. Timeaveraged
statistics, spectra of velocity and its higher order moments
are presented and explained.
Abstract: A portable sensor for the analysis of phosphate in
aqueous samples has been developed. The sensor incorporates
microfluidic technology, colorimetric detection, and wireless
communications into a compact and rugged portable device. The
detection method used is the molybdenum yellow method, in which a
phosphate-containing sample is mixed with a reagent containing
ammonium metavanadate and ammonium molybdate in an acidic
medium. A yellow-coloured compound is generated and the
absorption of this compound is measured using a light emitting diode
(LED) light source and a photodiode detector. The absorption is
directly proportional to the phosphate concentration in the original
sample. In this paper we describe the application of this phosphate
sensor to the analysis of wastewater at a municipal wastewater
treatment plant in Co. Kildare, Ireland.
Abstract: Due to the high increase in and demand for a wide assortment of applications that require low-cost, high-efficiency, and compact systems, RF power amplifiers are considered the most critical design blocks and power consuming components in wireless communication, TV transmission, radar, and RF heating. Therefore, much research has been carried out in order to improve the performance of power amplifiers. Classes-A, B, C, D, E and F are the main techniques for realizing power amplifiers.
An implementation of high efficiency class-F power amplifier with Gallium Nitride (GaN) High Electron Mobility Transistor (HEMT) was realized in this paper. The simulation and optimization of the class-F power amplifier circuit model was undertaken using Agilent’s Advanced Design system (ADS). The circuit was designed using lumped elements.
Abstract: This paper describes an experimental, theoretical
model and numerical study of concentrated vortex flow past a sphere
in a hydraulic check valve. The phenomenon of the rotation of the
ball around the axis of the device through which liquid flows has
been found. That is, due to the rotation of the sphere in the check
valve vibration is caused. We observe the rotation of the sphere
around the longitudinal axis of the check valve. This rotation is
induced by a vortex shedding from the sphere. We will discuss
computational simulation and experimental investigations of this
strong sphere rotation. The frequency of the sphere vibration and
interaction with the check valve wall has been measured as a function
of the wide range Reynolds Number. The validity of the
computational simulation and of the assumptions on which it is based
has been proved experimentally. This study demonstrates the
possibility to control the vibrations in a hydraulic system and proves
to be very effective suppression of the self-excited vibration.
Abstract: We developed a method based on quasi-molecular
modelling to simulate the fall of water drops on horizontally smooth
and rough surfaces. Each quasi-molecule was a group of particles
that interacted in a fashion entirely analogous to classical Newtonian
molecular interactions. When a falling water droplet was simulated at
low impact velocity on both smooth and rough surfaces, the droplets
moved periodically (i.e. the droplets moved up and down for a
certain period, finally they stopped moving and reached a steady
state), spreading and recoiling without splash or break-up. Spreading
rates of falling water droplets increased rapidly as time increased
until the spreading rate reached its steady state at time t ~ 0.25 s for
rough surface and t ~ 0.40 s for smooth surface. The droplet height
above both surfaces decreased as time increased, remained constant
after the droplet diameter attained a maximum value and reached its
steady state at time t ~ 0.4 s. However, rough surface had higher
spreading rates of falling water droplets and lower height on the
surface than smooth one.
Abstract: Based on a long-term vegetation index dataset of NDVI and meteorological data from 68 meteorological stations in the Qinghai-Tibet plateau and their relations with major climate factors were analyzed. The results show the following: 1) The linear trends of temperature in the Qinghai-Tibet plateau indicate that the temperature in the plateau generally increased, but it rose faster in the last 20 years. 2) The most significant NDVI increase occurred in the eastern and southern plateau. However, the western and northern plateau demonstrate a decreasing trend. 3) There is a significant positive linear correlation between NDVI and temperature and a negative correlation between NDVI and mean wind speed. However, no significant statistical relationship was found between NDVI and relative humidity, precipitation or sunshine duration.4) The changes in NDVI for the plateau are driven by temperature-precipitation, but for the desert and forest areas, the relation changes to precipitation-temperature-wind velocity and wind velocity-temperature-precipitation.
Abstract: The rate of production of main products of the Fischer-Tropsch reactions over Fe/HZSM5 bifunctional catalyst in a fixed bed reactor is investigated at a broad range of temperature, pressure, space velocity, H2/CO feed molar ratio and CO2, CH4 and water flow rates. Model discrimination and parameter estimation were performed according to the integral method of kinetic analysis. Due to lack of mechanism development for Fisher – Tropsch Synthesis on bifunctional catalysts, 26 different models were tested and the best model is selected. Comprehensive one and two dimensional heterogeneous reactor models are developed to simulate the performance of fixed-bed Fischer – Tropsch reactors. To reduce computational time for optimization purposes, an Artificial Feed Forward Neural Network (AFFNN) has been used to describe intra particle mass and heat transfer diffusion in the catalyst pellet. It is seen that products' reaction rates have direct relation with H2 partial pressure and reverse relation with CO partial pressure. The results show that the hybrid model has good agreement with rigorous mechanistic model, favoring that the hybrid model is about 25-30 times faster.
Abstract: A seismic isolation pad produced by utilizing the scrap
tire rubber which contains interleaved steel reinforcing cords has been
proposed. The steel cords are expected to function similar to the steel
plates used in conventional laminated rubber bearings. The scrap tire
rubber pad (STRP) isolator is intended to be used in low rise
residential buildings of highly seismic areas of the developing
countries. Experimental investigation was conducted on unbonded
STRP isolators, and test results provided useful information including
stiffness, damping values and an eventual instability of the isolation
unit. Finite element analysis (FE analysis) of STRP isolator was
carried out on properly bonded samples. These types of isolators
provide positive incremental force resisting capacity up to shear strain
level of 155%. This paper briefly discusses the force deformation
behavior of bonded STRP isolators including stability of the isolation
unit.
Abstract: Multicast transmissions allow an host (the source) to send only one flow bound for a group of hosts (the receivers). Any equipment eager to belong to the group may explicitly register itself to that group via its multicast router. This router will be given the responsibility to convey all information relating to the group to all registered hosts. However in an environment in which the final receiver or the source frequently moves, the multicast flows need particular treatment. This constitutes one of the multicast transmissions problems around which several proposals were made in the Mobile IPv6 case in general. In this article, we describe the problems involved in this IPv6 multicast mobility and the existing proposals for their resolution. Then architecture will be proposed aiming to satisfy and optimize these transmissions in the specific case of a mobile multicast receiver in NC-HMIPv6 environment.