Abstract: Exploratory missions to Mars and Titan have increased recently with various endeavors to find an alternate home to humankind. The use of surface rovers has its limitations due to rugged and uneven surfaces of these planetary bodies. The use of aerial robots requires the complete aerodynamic characterization of these vehicles in the atmospheric conditions of these planetary bodies. The dynamic stall phenomenon is extremely important for rotary wings performance under low Reynolds number that can be encountered in Martian and Titan’s atmosphere. The current research focuses on the aerodynamic characterization and exploration of the dynamic stall phenomenon of two different airfoils viz. E387 and Selig-Donovan7003 in Martian and Titan’s atmosphere at low Reynolds numbers of 10000 and 50000. The two-dimensional numerical simulations are conducted using commercially available finite volume solver with multi-species non-reacting mixture of gases as the working fluid. The k-epsilon (k-ε) turbulence model is used to capture the unsteady flow separation and the effect of turbulence. The dynamic characteristics are studied at a fixed different constant rotational extreme of angles of attack. This study of airfoils at different low Reynolds number and atmospheric conditions on Mars and Titan will be resulting in defining the aerodynamic characteristics of these airfoils for unmanned aerial missions for outer space exploration.
Abstract: Significant legislative changes are set to revolutionise the commercial shipping industry. Upcoming emissions restrictions will force operators to look at technologies that can improve the efficiency of their vessels -reducing fuel consumption and emissions. A device which may help in this challenge is the Ship Wind-Assisted Propulsion system (SWAP), an actively controlled aerofoil mounted vertically on the deck of a ship. The device functions in a similar manner to a sail on a yacht, whereby the aerodynamic forces generated by the sail reach an equilibrium with the hydrodynamic forces on the hull and a forward velocity results. Numerical and experimental testing of the SWAP device is presented in this study. Circulation control takes the form of a co-flow jet aerofoil, utilising both blowing from the leading edge and suction from the trailing edge. A jet at the leading edge uses the Coanda effect to energise the boundary layer in order to delay flow separation and create high lift with low drag. The SWAP concept has been originated by the research and development team at SMAR Azure Ltd. The device will be retrofitted to existing ships so that a component of the aerodynamic forces acts forward and partially reduces the reliance on existing propulsion systems. Wind tunnel tests have been carried out at the de Havilland wind tunnel at the University of Glasgow on a 1:20 scale model of this system. The tests aim to understand the airflow characteristics around the aerofoil and investigate the approximate lift and drag coefficients that an early iteration of the SWAP device may produce. The data exhibits clear trends of increasing lift as injection momentum increases, with critical flow attachment points being identified at specific combinations of jet momentum coefficient, Cµ, and angle of attack, AOA. Various combinations of flow conditions were tested, with the jet momentum coefficient ranging from 0 to 0.7 and the AOA ranging from 0° to 35°. The Reynolds number across the tested conditions ranged from 80,000 to 240,000. Comparisons between 2D computational fluid dynamics (CFD) simulations and the experimental data are presented for multiple Reynolds-Averaged Navier-Stokes (RANS) turbulence models in the form of normalised surface pressure comparisons. These show good agreement for most of the tested cases. However, certain simulation conditions exhibited a well-documented shortcoming of RANS-based turbulence models for circulation control flows and over-predicted surface pressures and lift coefficient for fully attached flow cases. Work must be continued in finding an all-encompassing modelling approach which predicts surface pressures well for all combinations of jet injection momentum and AOA.
Abstract: The aim of the research work is to modify the NACA 4215 airfoil with flap and rotary cylinder at the leading edge of the airfoil and experimentally study the static pressure distribution over the airfoil completed with flap and leading-edge vortex generator. In this research, NACA 4215 wing model has been constructed by generating the profile geometry using the standard equations and design software such as AutoCAD and SolidWorks. To perform the experiment, three wooden models are prepared and tested in subsonic wind tunnel. The experiments were carried out in various angles of attack. Flap angle and momentum injection rate are changed to observe the characteristics of pressure distribution. In this research, a new concept of flow separation control mechanism has been introduced to improve the aerodynamic characteristics of airfoil. Control of flow separation over airfoil which experiences a vortex generator (rotating cylinder) at the leading edge of airfoil is experimentally simulated under the effects of momentum injection. The experimental results show that the flow separation control is possible by the proposed mechanism, and benefits can be achieved by momentum injection technique. The wing performance is significantly improved due to control of flow separation by momentum injection method.
Abstract: The current study couples a quasi-steady Vortex Lattice
Method and a camber correcting technique, ‘Decambering’ for
unsteady post-stall flow prediction. The wake is force-free and
discrete such that the wake lattices move with the free-stream once
shed from the wing. It is observed that the time-averaged unsteady
coefficient of lift sees a relative drop at post-stall angles of attack
in comparison to its steady counterpart for some angles of attack.
Multiple solutions occur at post-stall and three different algorithms
to choose solutions in these regimes show both unsteadiness and
non-convergence of the iterations. The distribution of coefficient of
lift on the wing span also shows sawtooth. Distribution of vorticity
changes both along span and in the direction of the free-stream as
the wake develops over time with distinct roll-up, which increases
with time.
Abstract: Computations for two-dimensional flow past a stationary and harmonically pitching wind turbine airfoil at a moderate value of Reynolds number (400000) are carried out by progressively increasing the angle of attack for stationary airfoil and at fixed pitching frequencies for rotary one. The incompressible Navier-Stokes equations in conjunction with Unsteady Reynolds Average Navier-Stokes (URANS) equations for turbulence modeling are solved by OpenFOAM package to investigate the aerodynamic phenomena occurred at stationary and pitching conditions on a NACA 6-series wind turbine airfoil. The aim of this study is to enhance the accuracy of numerical simulation in predicting the aerodynamic behavior of an oscillating airfoil in OpenFOAM. Hence, for turbulence modelling, k-ω-SST with low-Reynolds correction is employed to capture the unsteady phenomena occurred in stationary and oscillating motion of the airfoil. Using aerodynamic and pressure coefficients along with flow patterns, the unsteady aerodynamics at pre-, near-, and post-static stall regions are analyzed in harmonically pitching airfoil, and the results are validated with the corresponding experimental data possessed by the authors. The results indicate that implementing the mentioned turbulence model leads to accurate prediction of the angle of static stall for stationary airfoil and flow separation, dynamic stall phenomenon, and reattachment of the flow on the surface of airfoil for pitching one. Due to the geometry of the studied 6-series airfoil, the vortex on the upper surface of the airfoil during upstrokes is formed at the trailing edge. Therefore, the pattern flow obtained by our numerical simulations represents the formation and change of the trailing-edge vortex at near- and post-stall regions where this process determines the dynamic stall phenomenon.
Abstract: Non-Newtonian fluid properties can change the flow
behaviour significantly, its prediction is more difficult when thermal
effects come into play. Hence, the focal point of this work is the
wake flow behind a heated circular cylinder in the laminar vortex
shedding regime for thermo-viscous shear thinning fluids. In the case
of isothermal flows of Newtonian fluids the vortex shedding regime
is characterised by a distinct Reynolds number and an associated
Strouhal number. In the case of thermo-viscous shear thinning
fluids the flow regime can significantly change in dependence of
the temperature of the viscous wall of the cylinder. The Reynolds
number alters locally and, consequentially, the Strouhal number
globally. In the present CFD study the temperature dependence of
the Reynolds and Strouhal number is investigated for the flow of a
Carreau fluid around a heated cylinder. The temperature dependence
of the fluid viscosity has been modelled by applying the standard
Williams-Landel-Ferry (WLF) equation. In the present simulation
campaign thermal boundary conditions have been varied over a
wide range in order to derive a relation between dimensionless heat
transfer, Reynolds and Strouhal number. Together with the shear
thinning due to the high shear rates close to the cylinder wall
this leads to a significant decrease of viscosity of three orders of
magnitude in the nearfield of the cylinder and a reduction of two
orders of magnitude in the wake field. Yet the shear thinning effect
is able to change the flow topology: a complex K´arm´an vortex street
occurs, also revealing distinct characteristic frequencies associated
with the dominant and sub-dominant vortices. Heating up the cylinder
wall leads to a delayed flow separation and narrower wake flow,
giving lesser space for the sequence of counter-rotating vortices. This
spatial limitation does not only reduce the amplitude of the oscillating
wake flow it also shifts the dominant frequency to higher frequencies,
furthermore it damps higher harmonics. Eventually the locally heated
wake flow smears out. Eventually, the CFD simulation results of the
systematically varied thermal flow parameter study have been used
to describe a relation for the main characteristic order parameters.
Abstract: For a bluff body, roughness elements in simulating a turbulent boundary layer, leading to delayed flow separation, a smaller wake, and lower form drag. In the present work, flow past a circular cylinder with using tripping wires is studied experimentally. The wind tunnel used for modeling free stream is open blow circuit (maximum speed = 30m/s and maximum turbulence of free stream = 0.1%). The selected Reynolds number for all tests was constant (Re = 25000). The circular cylinder selected for this experiment is 20 and 400mm in diameter and length, respectively. The aim of this research is to find the optimal operation mode. In this study installed some tripping wires 1mm in diameter, with a different number of wires on the circular cylinder and the wake characteristics of the circular cylinder is studied. Results showed that by increasing number of tripping wires attached to the circular cylinder (6, 8, and 10, respectively), The optimal angle for the tripping wires with 1mm in diameter to be installed on the cylinder is 60̊ (or 6 wires required at angle difference of 60̊). Strouhal number for the cylinder with tripping wires 1mm in diameter at angular position 60̊ showed the maximum value.
Abstract: Numerical investigations are performed to analyze the flow behavior over NACA0015 and to evaluate the efficiency of synthetic jet as active control device. The second objective of this work is to investigate the influence of momentum coefficient of synthetic jet on the flow behaviour. The unsteady Reynolds-averaged Navier-Stokes equations of the turbulent flow are solved using, k-ω SST provided by ANSYS CFX-CFD code. The model presented in this paper is a comprehensive representation of the information found in the literature. Comparison of obtained numerical flow parameters with the experimental ones shows that the adopted computational procedure reflects nearly the real flow nature. Also, numerical results state that use of synthetic jets devices has positive effects on the flow separation, and thus, aerodynamic performance improvement of NACA0015 airfoil. It can also be observed that the use of synthetic jet increases the lift coefficient about 13.3% and reduces the drag coefficient about 52.7%.
Abstract: This paper seeks the potentials of studying aerodynamic characteristics of inward cavities called dimples, as an alternative to the classical vortex generators. Increasing stalling angle is a greater challenge in wing design. But our examination is primarily focused on increasing lift. In this paper, enhancement of lift is mainly done by introduction of dimple or cavity in a wing. In general, aircraft performance can be enhanced by increasing aerodynamic efficiency that is lift to drag ratio of an aircraft wing. Efficiency improvement can be achieved by improving the maximum lift co-efficient or by reducing the drag co-efficient. At the time of landing aircraft, high angle of attack may lead to stalling of aircraft. To avoid this kind of situation, increase in the stalling angle is warranted. Hence, improved stalling characteristic is the best way to ease landing complexity. Computational analysis is done for the wing segment made of NACA 0012. Simulation is carried out for 30 m/s free stream velocity over plain airfoil and different types of cavities. The wing is modeled in CATIA V5R20 and analyses are carried out using ANSYS CFX. Triangle and square shapes are used as cavities for analysis. Simulations revealed that cavity placed on wing segment shows an increase of maximum lift co-efficient when compared to normal wing configuration. Flow separation is delayed at downstream of the wing by the presence of cavities up to a particular angle of attack.
Abstract: A recently developed one-equation turbulence model
has been successfully applied to simulate turbulent flows with
various complexities. The model, which is based on the
transformation of the k-ε closure, is wall-distance free and equipped
with lagging destruction/dissipation terms. Test cases included shockboundary-
layer interaction flows over the NACA 0012 airfoil, an
axisymmetric bump, and the ONERA M6 wing. The capability of the
model to operate in a Scale Resolved Simulation (SRS) mode is
demonstrated through the simulation of a massive flow separation
over a circular cylinder at Re= 1.2 x106. An assessment of the results
against available experiments Menter (k-ε)1Eq and the Spalart-
Allmaras model that belongs to the single equation closure family is
made.
Abstract: The aim of the present study is to computationally evaluate the hemodynamic factors which affect the formation of atherosclerosis and plaque rupture in the human artery. An increase of atherosclerosis disease in the artery causes geometry changes, which results in hemodynamic changes such as flow separation, reattachment, and adhesion of new cells (chemotactic) in the artery. Hence, geometry plays an important role in the determining the nature of hemodynamic patterns. Influence of stenosis in the non-bifurcating artery, under pulsatile flow condition, has been studied on an idealized geometry. Analysis of flow through symmetric and asymmetric stenosis in the artery revealed the significance of oscillating shear index (OSI), flow separation, low WSS zones and secondary flow patterns on plaque formation. The observed characteristic of flow in the post-stenotic region highlight the importance of plaque eccentricity on the formation of secondary stenosis on the arterial wall.
Abstract: A computational study on bio-inspired NACA634-021 hydrofoils with leading-edge protuberances has been carried out to investigate their hydrodynamic flow control characteristics at a Reynolds number of 14,000 and different angles-of-attack. The numerical simulations were performed using ANSYS FLUENT and based on Reynolds-Averaged Navier-Stokes (RANS) solver mode incorporated with k-ω Shear Stress Transport (SST) turbulence model. The results obtained indicate varying flow phenomenon along the peaks and troughs over the span of the hydrofoils. Compared to the baseline hydrofoil with no leading-edge protuberances, the leading-edge modified hydrofoils tend to reduce flow separation extents along the peak regions. In contrast, there are increased flow separations in the trough regions of the hydrofoil with leading-edge protuberances. Interestingly, it was observed that dissimilar flow separation behaviour is produced along different peak- or trough-planes along the hydrofoil span, even though the troughs or peaks are physically similar at each interval for a particular hydrofoil. Significant interactions between adjacent flow structures produced by the leading-edge protuberances have also been observed. These flow interactions are believed to be responsible for the dissimilar flow separation behaviour along physically similar peak- or trough-planes.
Abstract: Compressor fans in modern aircraft engines are of considerate importance, as they provide majority of thrust required by the aircraft. Their challenging environment is frequently subjected to non-uniform inflow conditions. These conditions could be either due to the flight operating requirements such as take-off and landing, wake interference from aircraft fuselage or cross-flow wind conditions. So, in highly maneuverable flights regimes of fighter aircrafts affects the overall performance of an engine. Since the flow in compressor of an aircraft application is highly sensitive because of adverse pressure gradient due to different flow orientations of the aircraft. Therefore, it is prone to unstable operations. This paper presents the study that focuses on axial compressor response to inlet flow orientations for the range of angles as 0 to 15 degrees. For this purpose, NASA Rotor-37 was taken and CFD mesh was developed. The compressor characteristics map was generated for the design conditions of pressure ratio of 2.106 with the rotor operating at rotational velocity of 17188.7 rpm using CFD simulating environment of ANSYS-CFX®. The grid study was done to see the effects of mesh upon computational solution. Then, the mesh giving the best results, (when validated with the available experimental NASA’s results); was used for further distortion analysis. The flow in the inlet nozzle was given angle orientations ranging from 0 to 15 degrees. The CFD results are analyzed and discussed with respect to stall margin and flow separations due to induced distortions.
Abstract: Traditional mechanical control systems in thrust
vectoring are efficient in rocket thrust guidance but their costs
and their weights are excessive. The fluidic injection in the nozzle
divergent constitutes an alternative procedure to achieve the goal. In
this paper, we present a 3D analytical model for fluidic injection
in a supersonic nozzle integrating an orifice. The fluidic vectoring
uses a sonic secondary injection in the divergent. As a result, the
flow and interaction between the main and secondary jet has built in
order to express the pressure fields from which the forces and thrust
vectoring are deduced. Under various separation criteria, the present
analytical model results are compared with the existing numerical
and experimental data from the literature.
Abstract: The main objective of aircraft aerodynamics is to
enhance the aerodynamic characteristics and maneuverability of the
aircraft. This enhancement includes the reduction in drag and stall
phenomenon. The airfoil which contains dimples will have
comparatively less drag than the plain airfoil. Introducing dimples on
the aircraft wing will create turbulence by creating vortices which
delays the boundary layer separation resulting in decrease of pressure
drag and also increase in the angle of stall. In addition, wake
reduction leads to reduction in acoustic emission. The overall
objective of this paper is to improve the aircraft maneuverability by
delaying the flow separation point at stall and thereby reducing the
drag by applying the dimple effect over the aircraft wing. This project
includes both computational and experimental analysis of dimple
effect on aircraft wing, using NACA 0018 airfoil. Dimple shapes of
Semi-sphere, hexagon, cylinder, square are selected for the analysis;
airfoil is tested under the inlet velocity of 30m/s and 60m/s at
different angle of attack (5˚, 10˚, 15˚, 20˚, and 25˚). This analysis
favors the dimple effect by increasing L/D ratio and thereby
providing the maximum aerodynamic efficiency, which provides the
enhanced performance for the aircraft.
Abstract: For a bluff body, dimples behave like roughness
elements in stimulating a turbulent boundary layer, leading to delayed
flow separation, a smaller wake and lower form drag. This is very
different in principle from the application of dimples to streamlined
body, where any reduction in drag would be predominantly due to a
reduction in skin friction. In the present work, a car model with
different dimple geometry is simulated using k-ε turbulence modeling
to determine its effect to the aerodynamics performance. Overall, the
results show that the application of dimples manages to reduce the
drag coefficient of the car model.
Abstract: Stator elements «Vane diffuser + crossover + return
channel» of stages with different specific speed were investigated by
CFD calculations. The regime parameter was introduced to present
efficiency and loss coefficient performance of all elements together.
Flow structure demonstrated advantages and disadvantages of design.
Flow separation in crossovers was eliminated by its shape
modification. Efficiency increased visibly. Calculated CFD
performances are in acceptable correlation with predicted ones by
engineering design method. The information obtained is useful for
design method better calibration.
Abstract: Parameters of flow are calculated in vaneless diffusers
with relative width 0,014–0,10. Inlet angles of flow and similarity
criteria were varied. There is information on flow separation,
boundary layer development, configuration of streamlines.
Polytrophic efficiency, loss coefficient and recovery coefficient are
used to compare effectiveness of diffusers. The sample of
optimization of narrow diffuser with conical walls is presented. Three
wide diffusers with narrowing walls are compared. The work is made
in the R&D laboratory “Gas dynamics of turbo machines” of the TU
SPb.
Abstract: This numerical study aims to develop a coupled,
passive and active control strategy of the flow around a cylinder of
diameter D, and Re=4000. The strategy consists to put a cylindrical
rod in front of a deforming cylinder. The quasi- elliptical deformation
of cylinder follow a sinusoidal law in order to reduce the drag force.
To analyze the evolution of unsteady vortices, the Large Eddy
Simulation approach is used in this 2D simulation, carried out using
ANSYS – Fluent. The movement of deformation is reproduced using
an internal subroutine, introduced in the form of a User Defined
Function UDF. Two diameters of the rod were tested for a rod placed
at a distance L = 3 ×d, with an amplitudes of deformation A = 5%, A
= 25% and A = 50% of the cylinder diameter, the frequency of
deformation take the values fd = 1fn, 5fn and 8fn, which fn
represents the naturel vortex shedding frequency. The results show
substantial changes in the flow behavior and for a rod of 6mm (1%
D) with amplitude A = 25%, and with a 2fn frequency, drag
reduction of 60% was recorded.
Abstract: This study involves numerical simulation of the flow
around a NACA2415 airfoil, with a 18° angle of attack, and flow
separation control using a rod, It involves putting a cylindrical rod -
upstream of the leading edge- in vertical translation movement in
order to accelerate the transition of the boundary layer by interaction
between the rod wake and the boundary layer. The viscous, nonstationary
flow is simulated using ANSYS FLUENT 13. The rod
movement is reproduced using the dynamic mesh technique and an
in-house developed UDF (User Define Function). The frequency
varies from 75 to 450 Hz and the considered amplitudes are 2%, and
3% of the foil chord. The frequency chosen closed to the frequency
of separation. Our results showed a substantial modification in the
flow behavior and a maximum drag reduction of 61%.