Abstract: This paper reveals the interaction between hydrogen
and surface stress in austenitic stainless steel by X-ray diffraction
stress measurement and thermal desorption analysis before and after
being charged with hydrogen. The surface residual stress was varied
by surface finishing using several disc polishing agents. The obtained
results show that the residual stress near surface had a significant
effect on hydrogen absorption behavior, that is, tensile residual stress
promoted the hydrogen absorption and compressive one did opposite.
Also, hydrogen induced equi-biaxial stress and this stress has a linear
correlation with hydrogen content.
Abstract: The knowledge of biodiesel density over large ranges
of temperature and pressure is important for predicting the behavior
of fuel injection and combustion systems in diesel engines, and for
the optimization of such systems. In this study, cottonseed oil was
transesterified into biodiesel and its density was measured at
temperatures between 288 K and 358 K and pressures between 0.1
MPa and 30 MPa, with expanded uncertainty estimated as ±1.6 kg⋅m-
3. Experimental pressure-volume-temperature (pVT) cottonseed data
was used along with literature data relative to other 18 biodiesels, in
order to build a database used to test the correlation of density with
temperarure and pressure using the Goharshadi–Morsali–Abbaspour
equation of state (GMA EoS). To our knowledge, this is the first that
density measurements are presented for cottonseed biodiesel under
such high pressures, and the GMA EoS used to model biodiesel
density. The new tested EoS allowed correlations within 0.2 kg·m-3
corresponding to average relative deviations within 0.02%. The built
database was used to develop and test a new full predictive model
derived from the observed linear relation between density and degree
of unsaturation (DU), which depended from biodiesel FAMEs
profile. The average density deviation of this method was only about
3 kg.m-3 within the temperature and pressure limits of application.
These results represent appreciable improvements in the context of
density prediction at high pressure when compared with other
equations of state.
Abstract: In recent decades with the development of technology
and lack of food sources, sewage sludge in production of human
foods is inevitable. Various sources of municipal and industrial
sewage sludge that is produced can provide the requirement of plant
nutrients. Soils in arid, semi-arid climate of central Iran that most
affected by water drainage, iron and zinc deficiencies, using of
sewage sludge is helpful. Therefore, the aim of this study is
investigation of sewage sludge and manure application on Ni, Pb and
Cd uptake by Savory. An experiment in a randomized complete block
design with three replications was performed. Sewage sludge
treatments consisted of four levels, control, 15, 30, 80 tons per
hectares; the manure was used in four levels of control, 20, 40 and 80
tons per hectare. Results showed that the wet and dry weights was not
affected by sewage sludge using, while, manure has significant effect
on them. The effect of sewage sludge on the cadmium and lead
concentrations were significant. Interactions of sewage sludge and
manure on dry weight values were not significant. Compare mean
analysis showed that increasing the amount of sewage sludge had no
significant effect on cadmium concentration and it reduced when
sewage sludge usage increased. This is probably due to increased
plant growth and reduced concentrations of these elements in the
plant.
Abstract: Aluminum hybrid reinforcement technology is a
response to the dynamic ever increasing service requirements of such
industries as transportation, aerospace, automobile, marine, etc. It is
unique in that it offers a platform of almost unending combinations of
materials to produce various hybrid composites. This article reviews
the studies carried out on various combinations of aluminum hybrid
composite and the effects on mechanical, physical and chemical
properties. It is observed that the extent of enhancement of these
properties of hybrid composites is strongly dependent on the nature
of the reinforcement, its hardness, particle size, volume fraction,
uniformity of dispersion within the matrix and the method of hybrid
production.
Abstract: This paper represents performance of particle swarm
optimisation (PSO) algorithm based integral (I) controller and
proportional-integral controller (PI) for interconnected hydro-thermal
automatic generation control (AGC) with generation rate constraint
(GRC) and Thyristor controlled phase shifter (TCPS) in series with
tie line. The control strategy of TCPS provides active control of
system frequency. Conventional objective function integral square
error (ISE) and another objective function considering square of
derivative of change in frequencies of both areas and change in tie
line power are considered. The aim of designing the objective
function is to suppress oscillation in frequency deviations and change
in tie line power oscillation. The controller parameters are searched
by PSO algorithm by minimising the objective functions. The
dynamic performance of the controllers I and PI, for both the
objective functions, are compared with conventionally optimized I
controller.
Abstract: In a highly competitive environment, it becomes more
important to shorten the whole business process while delivering or
even enhancing the business value to the customers and suppliers.
Although the workflow management systems receive much attention
for its capacity to practically support the business process enactment,
the effective workflow modeling method remain still challenging and
the high degree of process complexity makes it more difficult to gain
the short lead time. This paper presents a workflow structuring method
in a holistic way that can reduce the process complexity using
activity-needs and formal concept analysis, which eventually enhances
the key performance such as quality, delivery, and cost in business
process.
Abstract: The efficiency of wood vinegar mixed with each
individual of three plants extract such as: citronella grass
(Cymbopogon nardus), neem seed (Azadirachta indica A. Juss), and
yam bean seed (Pachyrhizus erosus Urb.) were tested against the
second instar larvae of housefly (Musca domestica L.). Steam
distillation was used for extraction of the citronella grass while neem
and yam bean were simple extracted by fermentation with ethyl
alcohol. Toxicity test was evaluated in laboratory based on two
methods of larvicidal bioassay: topical application method (contact
poison) and feeding method (stomach poison). Larval mortality was
observed daily and larval survivability was recorded until the
survived larvae developed to pupae and adults. The study resulted
that treatment of wood vinegar mixed with citronella grass showed
the highest larval mortality by topical application method (50.0%)
and by feeding method (80.0%). However, treatment of mixed wood
vinegar and neem seed showed the longest pupal duration to 25 day
and 32 days for topical application method and feeding method
respectively. Additional, larval duration on treated M. domestica
larvae was extended to 13 days for topical application method and 11
days for feeding method. Thus, the feeding method gave higher
efficiency compared with the topical application method.
Abstract: In this research article a comprehensive investigation
has been carried out to determine the effect of thermal cycle on
temperature dependent process parameters developed during gas
tungsten arc (GTA) welding of high carbon (AISI 1090) steel butt
joints. An experiment based thermal analysis has been performed to
obtain the thermal history. We have focused on different
thermophysical properties such as thermal conductivity, heat transfer
coefficient and cooling rate. Angular torch model has been utilized to
find out the surface heat flux and its variation along the fusion zone as
well as along the longitudinal direction from fusion boundary. After
welding and formation of weld pool, heat transfer coefficient varies
rapidly in the vicinity of molten weld bead and heat affected zone. To
evaluate the heat transfer coefficient near the fusion line and near the
rear end of the plate (low temperature region), established correlation
has been implemented and has been compared with empirical
correlation which is noted as coupled convective and radiation heat
transfer coefficient. Change in thermal conductivity has been
visualized by analytical model of moving point heat source. Rate of
cooling has been estimated by using 2-dimensional mathematical
expression of cooling rate and it has shown good agreement with
experimental temperature cycle. Thermophysical properties have been
varied randomly within 0 -10s time span.
Abstract: Botnets are one of the most serious and widespread
cyber threats. Today botnets have been facilitating many
cybercrimes, especially financial, top secret thefts. Botnets can be
available for lease in the market and are utilized by the
cybercriminals to launch massive attacks like DDoS, click fraud,
phishing attacks etc., Several large institutions, hospitals, banks,
government organizations and many social networks such as twitter,
facebook etc., became the target of the botmasters. Recently,
noteworthy researches have been carried out to detect bot, C&C
channels, botnet and botmasters. Using many sophisticated
technologies, botmasters made botnet a titan of the cyber world.
Innumerable challenges have been put forth by the botmasters to the
researchers in the detection of botnet. In this paper we present a
survey of different types of botnet C&C channels and also provide a
comparison of various botnet categories. Finally we hope that our
survey will create awareness for forthcoming botnet research
endeavors.
Abstract: Nowadays, the Web has become one of the most
pervasive platforms for information change and retrieval. It collects
the suitable and perfectly fitting information from websites that one
requires. Data mining is the form of extracting data’s available in the
internet. Web mining is one of the elements of data mining
Technique, which relates to various research communities such as
information recovery, folder managing system and simulated
intellects. In this Paper we have discussed the concepts of Web
mining. We contain generally focused on one of the categories of
Web mining, specifically the Web Content Mining and its various
farm duties. The mining tools are imperative to scanning the many
images, text, and HTML documents and then, the result is used by
the various search engines. We conclude by presenting a comparative
table of these tools based on some pertinent criteria.
Abstract: Two tragic tsunamis that devastated the west coast of
Sumatra Island, Indonesia in 2004 and North East Japan in 2011 had
damaged bridges to various extents. Tsunamis have resulted in the
catastrophic deterioration of infrastructures i.e. coastal structures,
utilities and transportation facilities. A bridge structure performs vital
roles to enable people to perform activities related to their daily needs
and for development. A damaged bridge needs to be repaired
expeditiously. In order to understand the effects of tsunami forces on
bridges, experimental tests are carried out to measure the
characteristics of hydrodynamic force at various wave heights.
Coastal bridge models designed at a 1:40 scale are used in a 24.0 m
long hydraulic flume with a cross section of 1.5 m by 2.0 m. The
horizontal forces and uplift forces in all cases show that forces
increase nonlinearly with increasing wave amplitude.
Abstract: The exposure to outdoor air pollution causes lung
cancer and increases the risk of bladder cancer. Because air pollution
in urban areas is mainly caused by transportation, it is necessary to
evaluate pollutant exhaust emissions from vehicles during their realworld
use. Nevertheless their evaluation and reduction is a key
problem, especially in the cities, that account for more than 50% of
world population.
A particular attention was given to the slope variability along the
streets during each journey performed by the instrumented vehicle.
In this paper we dealt with the problem of describing a
quantitatively approach for the reconstruction of GPS coordinates and
altitude, in the context of correlation study between driving cycles /
emission / geographical location, during an experimental campaign
realized with some instrumented cars.
Finally the slope analysis can be correlated to the emission and
consumption values in a specific road position, and it could be
evaluated its influence on their behaviour.
Abstract: Marine Protected Areas can benefit from nature based
tourism, monitoring environmental impacts and also become target
for human presence. From more than 3 million tourists visiting
Cozumel Island every year, an average of 2,8 million arrive by cruise
ship, and 41% are estimated to have motivation for water activities.
The destination is relying so much on the tourism activity, that scuba
diving and snorkeling in the National Park Reef of Cozumel sustain
the major economic activity. In order to achieve the sustainable
development indicator designed for regional environmental
development, the PNAC offers a training course to tourism providers
to access the protected area. This way, the update of the last 5 years
of such training is directed to diving staff, boat crew and
professionals, making them able to assist in managing the natural
resource. Moreover, the case study is an example to be used for
raising awareness among tourists visiting protected areas.
Abstract: Asphaltic concrete for pavement construction in India
are produced by using crushed stone, gravels etc. as aggregate. In
north-Eastern region of India, there is a scarcity of stone aggregate.
Therefore the road engineers are always in search of an optional
material as aggregate which can replace the regularly used material.
The purpose of this work was to evaluate the utilization of
substandard or marginal aggregates in flexible pavement
construction. The investigation was undertaken to evaluate the effects
of using lower quality aggregates such as over burnt brick aggregate
on the preparation of asphalt concrete for flexible pavements. The
scope of this work included a review of available literature and
existing data, a laboratory evaluation organized to determine the
effects of marginal aggregates and potential techniques to upgrade
these substandard materials, and a laboratory evaluation of these
upgraded marginal aggregate asphalt mixtures. Over burnt brick
aggregates are water susceptible and can leads to moisture damage.
Moisture damage is the progressive loss of functionality of the
material owing to loss of the adhesion bond between the asphalt
binder and the aggregate surface. Hence zycosoil as an anti striping
additive were evaluated in this study. This study summarizes the
results of the laboratory evaluation carried out to investigate the
properties of asphalt concrete prepared with zycosoil modified over
burnt brick aggregate. Marshall specimen were prepared with stone
aggregate, zycosoil modified stone aggregate, over burnt brick
aggregate and zycosoil modified over burnt brick aggregate. Results
show that addition of zycosoil with stone aggregate increased
stability by 6% and addition of zycosoil with over burnt brick
aggregate increased stability by 30%.
Abstract: Due to growing concern about environmental and
social consequences throughout the world, a need has been felt to
incorporate sustainability concepts in conventional manufacturing.
This paper is an attempt to identify and evaluate drivers in
implementing sustainable manufacturing in Indian context. Nine
possible drivers for successful implementation of sustainable
manufacturing have been identified from extensive review. Further,
Decision Making Trial and Evaluation Laboratory (DEMATEL)
approach has been utilized to evaluate and categorize these identified
drivers for implementing sustainable manufacturing in to the cause
and effect groups. Five drivers (Societal Pressure and Public
Concerns; Regulations and Government Policies; Top Management
Involvement, Commitment and Support; Effective Strategies and
Activities towards Socially Responsible Manufacturing and Market
Trends) have been categorized into the cause group and four drivers
(Holistic View in Manufacturing Systems; Supplier Participation;
Building Sustainable culture in Organization; and Corporate Image
and Benefits) have been categorized into the effect group. “Societal
Pressure and Public Concerns” has been found the most critical driver
and “Corporate Image and Benefits” as least critical or the most
easily influenced driver to implementing sustainable manufacturing
in Indian context. This paper may surely help practitioners in better
understanding of these drivers and their priorities towards effective
implementation of sustainable manufacturing.
Abstract: This paper evaluates the performance of a multi-lane
four legged modern roundabout operating in Muscat using SIDRA
model. The performance measures include Degree of Saturation
(DOS), average delay, and queue lengths. The geometric and traffic
data were used for model preparation. Gap acceptance parameters,
critical gap and follow up headway, were used for calibration of
SIDRA model. The results from the analysis showed that currently
the roundabout is experiencing delays up to 610 seconds per vehicle
with DOS 1.67 during peak hour. Further, sensitivity analysis for
general and roundabout parameters was performed, amongst lane
width, cruise speed, inscribed diameter, entry radius and entry angle
showed that inscribed diameter is most crucial factor affecting delay
and DOS. Up gradation of roundabout to fully signalized junction
was found as the suitable solution which will serve for future years
with LOS C for design year having DOS of 0.9 with average control
delay of 51.9 seconds per vehicle.
Abstract: This paper discusses the potential benefits of an
interactive multimedia information representation in enhancing
students’ critical thinking aligned with history reasoning in learning
history amongst Secondary School students in Malaysia. Two modes
of multimedia information representation were implemented;
chronologic and thematic information representations. A qualitative
study of an unstructured interview was conducted among two history
teachers, one history education lecturer, two i-think experts, and five
students from Form Four secondary school. The interview was to
elicit their opinions on the implementation of thinking maps and
interactive multimedia information representation in history learning.
The key elements of the interactive multimedia (e.g. multiple media,
user control, interactivity and use of timelines and concept maps)
were then considered to improve the learning process. Findings of the
preliminary investigation reveal that the interactive multimedia
information representations have the potential benefits to be
implemented as an instructional resource in enhancing students’
higher order thinking skills (HOTs). This paper concludes by giving
suggestions for future work.
Abstract: Essential oils are expensive phytochemicals produced
and extracted from specific species belonging to particular families in
the plant kingdom. In the United Arab Emirates country (UAE), is
located in the arid region of the world, nine species, from the
Lamiaceae family, having the capability to produce therapeutic grade
essential oils. These species include; Mentha spicata, Ocimum
forskolei, Salvia macrosiphon, Salvia aegyptiaca, Salvia macilenta,
Salvia spinosa, Teucrium polium, Teucrium stocksianum and Zataria
multiflora. Although, such potential species are indigenous to the
UAE, however, there are almost no studies available to investigate
the chemical composition and the quality of the extracted essential
oils under the UAE climatological conditions. Therefore, great
attention has to be given to such valuable natural resources, through
conducting highly supported research projects, tailored to the UAE
conditions, and investigating different extraction techniques,
including the application of the latest available technologies, such as
superficial fluid CO2. This is crucially needed; in order to accomplish
the greatest possibilities in the medicinal field, specifically in the
discovery of new therapeutic chemotypes, as well as, to achieve the
sustainability of this natural resource in the country.
Abstract: Two micromechanical models for 3D smart composite
with embedded periodic or nearly periodic network of generally
orthotropic reinforcements and actuators are developed and applied to
cubic structures with unidirectional orientation of constituents.
Analytical formulas for the effective piezothermoelastic coefficients
are derived using the Asymptotic Homogenization Method (AHM).
Finite Element Analysis (FEA) is subsequently developed and used
to examine the aforementioned periodic 3D network reinforced smart
structures. The deformation responses from the FE simulations are
used to extract effective coefficients. The results from both
techniques are compared. This work considers piezoelectric materials
that respond linearly to changes in electric field, electric
displacement, mechanical stress and strain and thermal effects. This
combination of electric fields and thermo-mechanical response in
smart composite structures is characterized by piezoelectric and
thermal expansion coefficients. The problem is represented by unitcell
and the models are developed using the AHM and the FEA to
determine the effective piezoelectric and thermal expansion
coefficients. Each unit cell contains a number of orthotropic
inclusions in the form of structural reinforcements and actuators.
Using matrix representation of the coupled response of the unit cell,
the effective piezoelectric and thermal expansion coefficients are
calculated and compared with results of the asymptotic
homogenization method. A very good agreement is shown between
these two approaches.
Abstract: The present study involved analysis of certain
characteristics of the perennial ryegrass (Lolium perenne L.)
genotypes collected from the natural flora of Ankara, and explores a
correlation among them. In order to evaluate the plants for breeding
purpose as per Turkey's environmental conditions, the perennial
ryegrass plants were collected from natural pasture of Ankara in 2004
and were utilized for the study. Seeds of the collected plants were
sown in pots and seedlings were prepared in a greenhouse. In 2005,
the seedlings were transplanted at 50 × 50 cm2 intervals in
Randomized Complete Blocks Design in an experimental field. In
2007 and 2008, data were recorded from the observations and
measurements of 568 perennial ryegrasses. The plant characteristics,
which were investigated, included re-growth time in spring, color,
density, growth habit, tendency to form inflorescence, time of
inflorescence, plant height, length of upper internode, spike length,
leaf length, leaf width, leaf area, leaf shape, number of spikelets per
spike, seed yield per spike and 1000 grain weight and the correlation
analyses were made using this data. Correlation coefficients were
estimated between all paired combinations of the studied traits. The
yield components exhibited varying trends of association among
themselves. Seed yield per spike showed significant and positive
association with the number of spikelets per spike, 1000 grain weight,
plant height, length of upper internode, spike length, leaf length, leaf
width, leaf area and color, but significant and negative association
with the growth habit and re-growth time in spring.