Abstract: Power transformer consists of components which are
under consistent thermal and electrical stresses. The major
component which degrades under these stresses is the paper
insulation of the power transformer. At site, lightning impulses and
cable faults may cause the winding deformation. In addition, the
winding may deform due to impact during transportation. A
deformed winding will excite more stress to its insulating paper thus
will degrade it. Insulation degradation will shorten the life-span of
the transformer. Currently there are two methods of detecting the
winding deformation which are Sweep Frequency Response
Analysis (SFRA) and Low Voltage Impulse Test (LVI). The latter
injects current pulses to the winding and capture the admittance
plot. In this paper, a transformer which experienced overheating and
arcing was identified, and both SFRA and LVI were performed.
Next, the transformer was brought to the factory for untanking. The
untanking results revealed that the LVI is more accurate than the
SFRA method for this case study.
Abstract: This paper presents the study of hardness profile of spur gear heated by induction heating process in function of the machine parameters, such as the power (kW), the heating time (s) and the generator frequency (kHz). The global work is realized by 3D finite-element simulation applied to the process by coupling and resolving the electromagnetic field and the heat transfer problems, and it was performed in three distinguished steps. First, a Comsol 3D model was built using an adequate formulation and taking into account the material properties and the machine parameters. Second, the convergence study was conducted to optimize the mesh. Then, the surface temperatures and the case depths were deeply analyzed in function of the initial current density and the heating time in medium frequency (MF) and high frequency (HF) heating modes and the edge effect were studied. Finally, the simulations results are validated using experimental tests.
Abstract: The avian phytohaemagglutinin skin test is being
proved as an in vivo system for the evaluation an avian in vivo T cell
mitogenicity. The test system was one week old Gallus domesticus
broiler Chickens. Five replicates were done for each of the whole,
1:10 dilutions of each of 0.05 IU tuberculin, tetanus immunoglobulin
and DPT vaccine as test materials. The evaluation parameters were
the skin indurations and lymphoblast percentages in bone marrow
lymphocytes.
Tuberculin indurations were 2.06 and 1.26mm for 0.05 IU
respectively while lymphoblast percent were 0.234 and 0.1
accordingly.
The skin indurations of 135mg/ml and 1.35mg/ml tetanus
immunoglobulin were 4.86 and 3.96mm while lymphoblast
percentages were 0.3 and 0.14 respectively.
The whole DPT and 1:10 concentration were with 4.5 and 3.2mm
while their lymphoblast percentages were 0.28 and 0.12 accordingly.
Thus the mitogenicity of the test materials was of dependant type.
Abstract: Aiming at most of the aviation products are facing the problem of fatigue fracture in vibration environment, we makes use of the testing result of a bracket, analysis for the structure with ANSYS-Workbench, predict the life of the bracket by different ways, and compared with the testing result. With the research on analysis methods, make an organic combination of simulation analysis and testing, Not only ensure the accuracy of simulation analysis and life predict, but also make a dynamic supervision of product life process, promote the application of finite element simulation analysis in engineering practice.
Abstract: The objective of this paper is to study the electrical
resistivity complexity between field and laboratory measurement, in
order to improve the effectiveness of data interpretation for
geophysical ground resistivity survey. The geological outcrop in
Penang, Malaysia with an obvious layering contact was chosen as the
study site. Two dimensional geoelectrical resistivity imaging were
used in this study to maps the resistivity distribution of subsurface,
whereas few subsurface sample were obtained for laboratory
advance. In this study, resistivity of samples in original conditions is
measured in laboratory by using time domain low-voltage technique,
particularly for granite core sample and soil resistivity measuring set
for soil sample. The experimentation results from both schemes are
studied, analyzed, calibrated and verified, including basis and
correlation, degree of tolerance and characteristics of substance.
Consequently, the significant different between both schemes is
explained comprehensively within this paper.
Abstract: In this paper, transversal vibration of buried pipelines
during loading induced by underground explosions is analyzed. The
pipeline is modeled as an infinite beam on an elastic foundation, so
that soil-structure interaction is considered by means of transverse
linear springs along the pipeline. The pipeline behavior is assumed to
be ideal elasto-plastic which an ultimate strain value limits the plastic
behavior. The blast loading is considered as a point load, considering
the affected length at some point of the pipeline, in which the
magnitude decreases exponentially with time. A closed-form solution
for the quasi-static problem is carried out for both elastic and elasticperfect
plastic behaviors of pipe materials. At the end, a comparative
study on steel and polyethylene pipes with different sizes buried in
various soil conditions, affected by a predefined underground
explosion is conducted, in which effect of each parameter is
discussed.
Abstract: Parallel programming models exist as an abstraction
of hardware and memory architectures. There are several parallel
programming models in commonly use; they are shared memory
model, thread model, message passing model, data parallel model,
hybrid model, Flynn-s models, embarrassingly parallel computations
model, pipelined computations model. These models are not specific
to a particular type of machine or memory architecture. This paper
expresses the model program for concurrent approach to data parallel
model through java programming.
Abstract: The aluminum bronze matrix alumina composites using hot press and resin infiltration were investigated to study their porosities, hardness, bending strengths, and microstructures. The experiment results show that the hardness of the sintered composites with the decrease of porosity increases. The composites without and with resin infiltration have about HRF 42-61 of about 34-40% of porosity and about HRF 62-83 of about 30-36% of porosity, respectively. Besides, the alumina composites contain a more amount of iron and nickel powders would cause a lower bending strength due to forming some weaker bonding among the iron, nickel, copper, aluminum under this hot pressing of shorter time.
Abstract: Histogram equalization is often used in image enhancement, but it can be also used in auto exposure. However, conventional histogram equalization does not work well when many pixels are concentrated in a narrow luminance range.This paper proposes an auto exposure method based on 2-way histogram equalization. Two cumulative distribution functions are used, where one is from dark to bright and the other is from bright to dark. In this paper, the proposed auto exposure method is also designed and implemented for image signal processors with full-HD images.
Abstract: The issue of unintentional islanding in PV grid
interconnection still remains as a challenge in grid-connected
photovoltaic (PV) systems. This paper discusses the overview of
popularly used anti-islanding detection methods, practically applied
in PV grid-connected systems. Anti-islanding methods generally can
be classified into four major groups, which include passive methods,
active methods, hybrid methods and communication base methods.
Active methods have been the preferred detection technique over the
years due to very small non-detected zone (NDZ) in small scale
distribution generation. Passive method is comparatively simpler
than active method in terms of circuitry and operations. However, it
suffers from large NDZ that significantly reduces its performance.
Communication base methods inherit the advantages of active and
passive methods with reduced drawbacks. Hybrid method which
evolved from the combination of both active and passive methods
has been proven to achieve accurate anti-islanding detection by many
researchers. For each of the studied anti-islanding methods, the
operation analysis is described while the advantages and
disadvantages are compared and discussed. It is difficult to pinpoint a
generic method for a specific application, because most of the
methods discussed are governed by the nature of application and
system dependent elements. This study concludes that the setup and
operation cost is the vital factor for anti-islanding method selection in
order to achieve minimal compromising between cost and system
quality.
Abstract: This study reveals that anti-immigrant policies in
Europe result from a process of securitization, and that, within this
process, radical right parties have been formulating discourses and
approaches through a construction process by using some common
security themes. These security themes can be classified as national
security, economic security, cultural security and internal security.
The frequency with which radical right parties use these themes may
vary according to the specific historical, social and cultural
characteristics of a particular country.
Abstract: The objective of this paper is to estimate realistic
principal extrusion process parameters by means of artificial neural
network. Conventionally, finite element analysis is used to derive
process parameters. However, the finite element analysis of the
extrusion model does not consider the manufacturing process
constraints in its modeling. Therefore, the process parameters
obtained through such an analysis remains highly theoretical.
Alternatively, process development in industrial extrusion is to a
great extent based on trial and error and often involves full-size
experiments, which are both expensive and time-consuming. The
artificial neural network-based estimation of the extrusion process
parameters prior to plant execution helps to make the actual extrusion
operation more efficient because more realistic parameters may be
obtained. And so, it bridges the gap between simulation and real
manufacturing execution system. In this work, a suitable neural
network is designed which is trained using an appropriate learning
algorithm. The network so trained is used to predict the
manufacturing process parameters.
Abstract: Sharing the manufacturing facility through remote
operation and monitoring of a machining process is challenge for
effective use the production facility. Several automation tools in term
of hardware and software are necessary for successfully remote
operation of a machine. This paper presents a prototype of workpiece
holding attachment for remote operation of milling process by self
configuration the workpiece setup. The prototype is designed with
mechanism to reorient the work surface into machining spindle
direction with high positioning accuracy. Variety of parts geometry
is hold by attachment to perform single setup machining. Pin type
with array pattern additionally clamps the workpiece surface from
two opposite directions for increasing the machining rigidity.
Optimum pins configuration for conforming the workpiece geometry
with minimum deformation is determined through hybrid algorithms,
Genetic Algorithms (GA) and Particle Swarm Optimization (PSO).
Prototype with intelligent optimization technique enables to hold
several variety of workpiece geometry which is suitable for
machining low of repetitive production in remote operation.
Abstract: Electrospinning is a broadly used technology to obtain
polymeric nanofibers ranging from several micrometers down to
several hundred nanometers for a wide range of applications. It offers
unique capabilities to produce nanofibers with controllable porous
structure. With smaller pores and higher surface area than regular
fibers, electrospun fibers have been successfully applied in various
fields, such as, nanocatalysis, tissue engineering scaffolds, protective
clothing, filtration, biomedical, pharmaceutical, optical electronics,
healthcare, biotechnology, defense and security, and environmental
engineering. In this study, polyurethane nanofibers were obtained
under different electrospinning parameters. Fiber morphology and
diameter distribution were investigated in order to understand them
as a function of process parameters.
Abstract: An optical fiber Fabry-Perot interferometer (FFPI) is
proposed and demonstrated for dynamic measurements in a
mechanical vibrating target. A polishing metal with a low reflectance
value adhered to a mechanical vibrator was excited via a function
generator at various excitation frequencies. Output interference
fringes were generated by modulating the reference and sensing
signal at the output arm. A fringe-counting technique was used for
interpreting the displacement information on the dedicated computer.
The fiber interferometer has been found the capability of the
displacement measurements of 1.28 μm – 96.01 μm. A commercial
displacement sensor was employed as a reference sensor for
investigating the measurement errors from the fiber sensor. A
maximum percentage measurement error of approximately 1.59 %
was obtained.
Abstract: Analytical solution of the first-order and third-order
shear deformation theories are developed to study the free vibration
behavior of simply supported functionally graded plates. The
material properties of plate are assumed to be graded in the thickness
direction as a power law distribution of volume fraction of the
constituents. The governing equations of functionally graded plates
are established by applying the Hamilton's principle and are solved
by using the Navier solution method. The influence of side-tothickness
ratio and constituent of volume fraction on the natural
frequencies are studied. The results are validated with the known
data in the literature.
Abstract: Different numerical methods are employed and developed for simulating interfacial flows. A large range of applications belong to this group, e.g. two-phase flows of air bubbles in water or water drops in air. In such problems surface tension effects often play a dominant role. In this paper, various models of surface tension force for interfacial flows, the CSF, CSS, PCIL and SGIP models have been applied to simulate the motion of small air bubbles in water and the results were compared and reviewed. It has been pointed out that by using SGIP or PCIL models, we are able to simulate bubble rise and obtain results in close agreement with the experimental data.
Abstract: Heterogeneity of solid waste characteristics as well as the complex processes taking place within the landfill ecosystem motivated the implementation of soft computing methodologies such as artificial neural networks (ANN), fuzzy logic (FL), and their combination. The present work uses a hybrid ANN-FL model that employs knowledge-based FL to describe the process qualitatively and implements the learning algorithm of ANN to optimize model parameters. The model was developed to simulate and predict the landfill gas production at a given time based on operational parameters. The experimental data used were compiled from lab-scale experiment that involved various operating scenarios. The developed model was validated and statistically analyzed using F-test, linear regression between actual and predicted data, and mean squared error measures. Overall, the simulated landfill gas production rates demonstrated reasonable agreement with actual data. The discussion focused on the effect of the size of training datasets and number of training epochs.
Abstract: The aim of the present study is to analyze the generation of osteoporotic vertebral bone induced by lack of calcium during growth period and analyze its effects for disc degeneration, based on biomechanical and histomorphometrical study. Mechanical and histomorphological characteristics of lumbar vertebral bones and discs of rats with calcium free diet (CFD) were detected and tracked by using high resolution in-vivo micro-computed tomography (in-vivo micro-CT), finite element (FE) and histological analysis. Twenty female Sprague-Dawley rats (6 weeks old, approximate weight 170g) were randomly divided into two groups (CFD group: 10, NOR group: 10). The CFD group was maintained on a refmed calcium-controlled semisynthetic diet without added calcium, to induce osteoporosis. All lumbar (L 1-L6) were scanned by using in vivo micro-CT with 35i.un resolution at 0, 4, 8 weeks to track the effects of CFD on the generation of osteoporosis. The fmdings of the present study indicated that calcium insufficiency was the main factor in the generation of osteoporosis and it induced lumbar vertebral disc degeneration. This study is a valuable experiment to firstly evaluate osteoporotic vertebral bone and disc degeneration induced by lack of calcium during growth period from a biomechanical and histomorphometrical point of view.
Abstract: research goal was to determine the expression levels cDNA of brain embrio at gestation days 10 (GD-10). The Electroforesis DNA results showed that GAPDH, Fibronectin1, Ncam1, Tenascin, Vimentin, Neurofilament heavy, Neurofilament medium and Neurofilament low were 447 bp, 462 bp, 293 bp. 416 bp, 327 bp, 301 bp, 398 bp and 289 bp. Result of real-time RT-PCR on brain Embryo at gestation days 10 showed that the expression of copy gen Fibronectin 36 copies, Ncam 21,708 copies; Tenascin 24,505 copies; Vimentin 538,554 copies; Neurofilament heavy 2,419 copies; Neurofilament medium 92,928 copies; Neurofilament low 125,809 copies. Vimentin expressed gene copies is very high compared with other gene copies. This condition are caused by Vimentin, that contribute to proliferate of brain development. The vimentin role to cell proliferation of brain.