Abstract: Small cell backhaul solutions need to be cost-effective, scalable, and easy to install. This paper presents an overview of small cell backhaul technologies. Wireless solutions including TV white space, satellite, sub-6 GHz radio wave, microwave and mmWave with their backhaul characteristics are discussed. Recent research on issues like beamforming, backhaul architecture, precoding and large antenna arrays, and energy efficiency for dense small cell backhaul with mmWave communications is reviewed. Recent trials of 5G technologies are summarized.
Abstract: Parallel Compressor Model (PCM) is a simplified approach to predict compressor performance with inlet distortions. In PCM calculation, it is assumed that the sub-compressors’ outlet static pressure is uniform and therefore simplifies PCM calculation procedure. However, if the compressor’s outlet duct is not long and straight, such assumption frequently induces error ranging from 10% to 15%. This paper provides a revised calculation method of PCM that can correct the error. The revised method employs energy equation, momentum equation and continuity equation to acquire needed parameters and replace the equal static pressure assumption. Based on the revised method, PCM is applied on two compression system with different blades types. The predictions of their performance in non-uniform inlet conditions are yielded through the revised calculation method and are employed to evaluate the method’s efficiency. Validating the results by experimental data, it is found that although little deviation occurs, calculated result agrees well with experiment data whose error ranges from 0.1% to 3%. Therefore, this proves the revised calculation method of PCM possesses great advantages in predicting the performance of the distorted compressor with limited exhaust duct.
Abstract: In present study, an approach is adopted where photovoltaic thermal flat plate collector is integrated with compound parabolic concentrator. Analytical expression of temperature dependent electrical efficiency of N number of partially covered Photovoltaic Thermal (PVT) - Compound Parabolic Concentrator (CPC) water collector connected in series has been derived with the help of basic thermal energy balance equations. Analysis has been carried for winter weather condition at Delhi location, India. Energy and exergy performance of N - partially covered Photovoltaic Thermal (PVT) - Compound Parabolic Concentrator (CPC) Water collector system has been compared for two cases: (i) 25% area of water collector covered by PV module, (ii) 75% area of water collector covered by PV module. It is observed that case (i) has been best suited for thermal performance and case (ii) for electrical energy as well as overall exergy.
Abstract: The increasing demand of electric power is giving an
emphasis on the need for the maximum utilization of renewable
energy sources. On the other hand maintaining power quality to
satisfaction of utility is an essential requirement. In this paper the
design aspects of a Unified Power Quality Conditioner integrated
with photovoltaic system in a distributed generation is presented. The
proposed system consist of series inverter, shunt inverter are
connected back to back on the dc side and share a common dc-link
capacitor with Distributed Generation through a boost converter. The
primary task of UPQC is to minimize grid voltage and load current
disturbances along with reactive and harmonic power compensation.
In addition to primary tasks of UPQC, other functionalities such as
compensation of voltage interruption and active power transfer to the
load and grid in both islanding and interconnected mode have been
addressed. The simulation model is design in MATLAB/ Simulation
environment and the results are in good agreement with the published
work.
Abstract: The new methods as accelerated steam distillation
assisted by microwave (ASDAM) is a combination of microwave
heating and steam distillation, performed at atmospheric pressure at
very short extraction time. Isolation and concentration of volatile
compounds are performed by a single stage. (ASDAM) has been
compared with (ASDAM) with cryogrinding of seeds (CG) and a
conventional technique, hydrodistillation assisted by microwave
(HDAM), hydro-distillation (HD) for the extraction of essential oil
from aromatic herb as caraway and cumin seeds. The essential oils
extracted by (ASDAM) for 1 min were quantitatively (yield) and
qualitatively (aromatic profile) no similar to those obtained by
ASDAM-CG (1 min) and HD (for 3 h). The accelerated microwave
extraction with cryogrinding inhibits numerous enzymatic reactions
as hydrolysis of oils.
Microwave radiations constitute the adequate mean for the
extraction operations from the yields and high content in major
component majority point view, and allow to minimise considerably
the energy consumption, but especially heating time too, which is one
of essential parameters of artifacts formation.
The ASDAM and ASDAM-CG are green techniques and yields an
essential oil with higher amounts of more valuable oxygenated
compounds comparable to the biosynthesis compounds, and allows
substantial savings of costs, in terms of time, energy and plant
material.
Abstract: This article explains the elements and considerations taken into account when implementing and applying patent evaluation and scientometric study in the identifications of technology trends, and the tools that led to the implementation of a software application for patent revision. Univariate analysis helped recognize the technological leaders in the field of energy, and steered the way for a multivariate analysis of this sample, which allowed for a graphical description of the techniques of mature technologies, as well as the detection of emerging technologies. This article ends with a validation of the methodology as applied to the case of fuel cells.
Abstract: This study attempts to consider the linkage between management and computer sciences in order to develop the software named “IntelSymb” as a demo application to prove data analysis of non-energy* fields’ diversification, which will positively influence on energy dependency mitigation of countries. Afterward, we analyzed 18 years of economic fields of development (5 sectors) of 13 countries by identifying which patterns mostly prevailed and which can be dominant in the near future. To make our analysis solid and plausible, as a future work, we suggest developing a gateway or interface, which will be connected to all available on-line data bases (WB, UN, OECD, U.S. EIA) for countries’ analysis by fields. Sample data consists of energy (TPES and energy import indicators) and non-energy industries’ (Main Science and Technology Indicator, Internet user index, and Sales and Production indicators) statistics from 13 OECD countries over 18 years (1995-2012). Our results show that the diversification of non-energy industries can have a positive effect on energy sector dependency (energy consumption and import dependence on crude oil) deceleration. These results can provide empirical and practical support for energy and non-energy industries diversification’ policies, such as the promoting of Information and Communication Technologies (ICTs), services and innovative technologies efficiency and management, in other OECD and non-OECD member states with similar energy utilization patterns and policies. Industries, including the ICT sector, generate around 4 percent of total GHG, but this is much higher — around 14 percent — if indirect energy use is included. The ICT sector itself (excluding the broadcasting sector) contributes approximately 2 percent of global GHG emissions, at just under 1 gigatonne of carbon dioxide equivalent (GtCO2eq). Ergo, this can be a good example and lesson for countries which are dependent and independent on energy, and mainly emerging oil-based economies, as well as to motivate non-energy industries diversification in order to be ready to energy crisis and to be able to face any economic crisis as well.
Abstract: Pure form of L-Dopa is used to enhance muscular development, fat breakdown and suppress Parkinson disease in humans. However, the L-Dopa in mucuna seed, when present with other antinutritional factors, causes nutritional disorders in monogastric animals. Information on the utilisation of pure L-Dopa in monogastric animals is scanty. Therefore, effect of L-Dopa on growth performance and carcass characteristics in broiler chickens was investigated. Two hundred and forty one-day-old chicks were allotted to six treatments, which consisted of a positive control (PC) with standard energy (3100Kcal/Kg) and negative control (NC) with high energy (3500Kcal/Kg). The rest 4 diets were NC+0.1, NC+0.2, NC+0.3 and NC+0.4% L-Dopa, respectively. All treatments had 4 replicates in a completely randomized design. Body weight gain, final weight, feed intake, dressed weight and carcass characteristics were determined. Body weight gain and final weight of birds fed PC were 1791.0 and 1830.0g, NC+0.1% L-Dopa were 1827.7 and 1866.7g and NC+0.2% L-Dopa were 1871.9 and 1910.9g respectively, and the feed intake of PC (3231.5g), were better than other treatments. The dressed weight at 1375.0g and 1357.1g of birds fed NC+0.1% and NC+0.2% L-Dopa, respectively, were similar but better than other treatments. Also, the thigh (202.5g and 194.9g) and the breast meat (413.8g and 410.8g) of birds fed NC+0.1% and NC+0.2% L-Dopa, respectively, were similar but better than birds fed other treatments. The drum stick of birds fed NC+0.1% L-Dopa (220.5g) was observed to be better than birds on other diets. Meat to bone ratio and relative organ weights were not affected across treatments. L-Dopa extract, at levels tested, had no detrimental effect on broilers, rather better bird performance and carcass characteristics were observed especially at 0.1% and 0.2% L-Dopa inclusion rates. Therefore, 0.2% inclusion is recommended in diets of broiler chickens for improved performance and carcass characteristics.
Abstract: The sun is an inexhaustible source and harness its potential both for heating and power generation is one of the most promising and necessary alternatives, mainly due to environmental issues. However, it should be noted that this has always been present in the generation of energy on earth, only indirectly, since it is responsible for virtually all other energy sources, such as generating source of evaporation of the water cycle, allowing the impoundment and the consequent generation of electricity (hydroelectric power); winds are caused by atmospheric induction caused by large scale solar radiation; petroleum, coal and natural gas were generated from waste plants and animals that originally derived energy required for their development of solar radiation. This paper presents a study on the feasibility of using solar energy for water heating in homes. A simplified methodology developed for formulation of solar heating operation model of water in alternative systems of solar energy in Brazil, and compared it to that in the international market. Across this research, it was possible to create new paradigms for alternative applications to the use of solar energy.
Abstract: For briquetting of metal chips are used hydraulic and
mechanical presses. The density of the briquettes in this case is about
60% - 70 % on the density of solid metal. In this work are presented
the results of experimental studies for briquetting of metal chips, by
using a new technology for impact briquetting. The used chips are by
Armco iron, steel, cast iron, copper, aluminum and brass. It has been
found that: (i) in a controlled impact the density of the briquettes can
be increases up to 30%; (ii) at the same specific impact energy Es
(J/sm3) the density of the briquettes increases with increasing of the
impact velocity; (iii), realization of the repeated impact leads to
decrease of chips density, which can be explained by distribution of
elastic waves in the briquette.
Abstract: In recent years, the use of renewable energy resources
instead of pollutant fossil fuels and other forms has increased.
Photovoltaic generation is becoming increasingly important as a
renewable resource since it does not cause in fuel costs, pollution,
maintenance, and emitting noise compared with other alternatives
used in power applications. In this paper, Perturb and Observe and
Incremental Conductance methods are used to improve energy
conversion efficiency under different environmental conditions. PI
controllers are used to control easily DC-link voltage, active and
reactive currents. The whole system is simulated under standard
climatic conditions (1000 W/m2, 250C) in MATLAB and the
irradiance is varied from 1000 W/m2 to 300 W/m2. The use of PI
controller makes it easy to directly control the power of the grid
connected PV system. Finally the validity of the system will be
verified through the simulations in MATLAB/Simulink environment.
Abstract: This research aims to develop ways of lodging
business management of Bang Khonthi community in Samut
Songkram province that are appropriate with the cultural context of
the Bang Khonthi community.
Eight lodging business owners were interviewed. It was found that
lodging business that are family business must be done with passion,
correct understanding of self, culture, nature, Thai way of life,
thorough, professional development, environmentally concerned,
building partnerships with various networks both community level,
and public sector and business cohorts. Public relations should be
done through media both traditional and modern outlets, such as
websites and social networks to provide customers convenience,
security, happiness, knowledge, love and value when travel to Bang
Khonthi. This will also help them achieve sustainability in business,
in line with the 10 Home Stay Standard Thailand.
Suggestions for operators are as follows: Operators need to
improve their public relations work. They need to use technology in
public relations such as the internet. Management standards must be
improved. Souvenir and local products shops should be arranged in
the compound. Product pricing must be set accordingly. They need to
join hands to help each other. Quality of the business operation
should be raised to meet the standards. Educational measures to
reduce the impact caused by tourism on the community such as
efforts to reduce energy consumption.
Abstract: We present a new subband adaptive filter (R-SAF)
which is robust against impulsive noise in system identification. To
address the vulnerability of adaptive filters based on the L2-norm
optimization criterion against impulsive noise, the R-SAF comes from
the L1-norm optimization criterion with a constraint on the energy
of the weight update. Minimizing L1-norm of the a posteriori error
in each subband with a constraint on minimum disturbance gives
rise to the robustness against the impulsive noise and the capable
convergence performance. Experimental results clearly demonstrate
that the proposed R-SAF outperforms the classical adaptive filtering
algorithms when impulsive noise as well as background noise exist.
Abstract: Water is essential for life and fresh water is a finite
resource that is becoming scarce day by day even though it is
recycled by hydrological cycle. The fresh water reserves are being
polluted due to expanding irrigation, industries, urban population and
its development. Contaminated water leads to several health
problems. With the increasing demand of fresh water, solar
distillation is an alternate solution which uses solar energy to
evaporate water and then to condense it, thereby collecting distilled
water within or outside the same system to use it as potable water.
The structure that houses the process is known as a 'solar still'. In this
paper, ‘Modified double slope solar still (MDSSS)’ & 'Modified
double slope basin type multiwick solar still (MDSBMSS)' have been
designed to convert saline, brackish water into drinking water. In this
work two different modified solar stills are fabricated to study the
performance of these solar stills. For modification of solar stills,
Fibre Reinforced Plastic (FRP) and Acrylic sheets are used. The
experiments in MDSBMSS and MDSSS was carried on 10
September 2015 & 5 November 2015 respectively. Performances of
the stills were investigated. The amount of distillate has been found
3624 Ml/day in MDSBMSS on 10 September 2015 and 2400 Ml/day
in MDSSS on 5 November 2015.
Abstract: The new design of heat exchangers utilizing an
annular distributor opens a new gateway for realizing higher energy
optimization. To realize this goal, graphene nanoplatelet-based water
nanofluids with promising thermophysical properties were
synthesized in the presence of covalent and noncovalent
functionalization. Thermal conductivity, density, viscosity and
specific heat capacity were investigated and employed as a raw data
for ANSYS-Fluent to be used in two-phase approach. After
validation of obtained results by analytical equations, two special
parameters of convective heat transfer coefficient and pressure drop
were investigated. The study followed by studying other heat transfer
parameters of annular pass in the presence of graphene nanopletelesbased
water nanofluids at different weight concentrations, input
powers and temperatures. As a result, heat transfer performance and
friction loss are predicted for both synthesized nanofluids.
Abstract: Experiments were performed to investigate the effects of roughness on the reattachment and redevelopment regions over a 12 mm forward facing step (FFS) in an open channel flow. The experiments were performed over an upstream smooth wall and a smooth FFS, an upstream wall coated with sandpaper 36 grit and a smooth FFS and an upstream rough wall produced from sandpaper 36 grit and a FFS coated with sandpaper 36 grit. To investigate only the wall roughness effects, Reynolds number, Froude number, aspect ratio and blockage ratio were kept constant. Upstream profiles showed reduced streamwise mean velocities close to the rough wall compared to the smooth wall, but the turbulence level was increased by upstream wall roughness. The reattachment length for the smooth-smooth wall experiment was 1.78h; however, when it is replaced with rough-smooth wall the reattachment length decreased to 1.53h. It was observed that the upstream roughness increased the physical size of contours of maximum turbulence level; however, the downstream roughness decreased both the size and magnitude of contours in the vicinity of the leading edge of the step. Quadrant analysis was performed to investigate the dominant Reynolds shear stress contribution in the recirculation region. The Reynolds shear stress and turbulent kinetic energy profiles after the reattachment showed slower recovery compared to the streamwise mean velocity, however all the profiles fairly collapse on their corresponding upstream profiles at x/h = 60. It was concluded that to obtain a complete collapse several more streamwise distances would be required.
Abstract: The present study is based on the three-dimensional digital analysis by the finite elements method of the mechanical loading effect on the delamination of unidirectional and multidirectional stratified composites. The aim of this work is the determination of the release energy rate G in mode I and the Von Mises equivalent constraint distribution along the damaged area under the influence of several parameters such as the applied load and the delamination size. The results obtained in this study show that the unidirectional composite laminates have better mechanical resistance one the loading line than the multidirectional composite laminates.
Abstract: This project aims at building an efficient and
automatic power monitoring SCADA system, which is capable of
monitoring the electrical parameters of high voltage powered devices
in real time for example RMS voltage and current, frequency, energy
consumed, power factor etc. The system uses RS-485 serial
communication interface to transfer data over longer distances.
Embedded C programming is the platform used to develop two
hardware modules namely: RTU and Master Station modules, which
both use the CC2540 BLE 4.0 microcontroller configured in slave /
master mode. The Si8900 galvanic ally isolated microchip is used to
perform ADC externally. The hardware communicates via UART
port and sends data to the user PC using the USB port. Labview
software is used to design a user interface to display current state of
the power loads being monitored as well as logs data to excel
spreadsheet file. An understanding of the Si8900’s auto baud rate
process is key to successful implementation of this project.
Abstract: The material selection problem is concerned with the
determination of the right material for a certain product to optimize
certain performance indices in that product such as mass, energy
density, and power-to-weight ratio. This paper is concerned about
optimizing the selection of the manufacturing process along with the
material used in the product under performance indices and
availability constraints. In this paper, the material selection problem
is formulated using binary programming and solved by genetic
algorithm. The objective function of the model is to minimize the
total manufacturing cost under performance indices and material and
manufacturing process availability constraints.
Abstract: By using an adequate thermal barrier coating in
buildings the energy saving will be happened. In this study, a range
of wall paints with different absorption coefficient in different
climates has been investigated. In order to study these effects, heating
and cooling loads of a common building with different ordinary
paints and paint with mineral coating have been calculated. The
effect of building paint in different climatic condition was studied
and comparison was done between ordinary paints and paint with
mineral insulators in temperate climate to obtain optimized energy
consumption. The results have been shown that coatings with
inorganic micro particles as insulation reduce the energy
consumption of buildings around 14%.