Abstract: We report here structural, mechanical and I-V
characteristics of Zn1-xMxO ceramic samples with various x and M.
It is found that the considered dopants does not influence the wellknown
peaks related to wurtzite structure of ZnO ceramics, while the
shape and size of grains are clearly affected. Average crystalline
diameters, deduced from XRD are between 42 nm and 54 nm, which
are 70 times lower than those obtained from SEM micrographs.
Interestingly, the potential barrier could be formed by adding Cu up
to 0.20, and it is completely deformed by 0.025 Ni additions. The
breakdown field could be enhanced up to 4138 V/cm by 0.025 Cu
additions, followed by a decrease with further increase of Cu . On
the other hand a gradual decrease in VHN is reported for both
dopants and their values are higher in Ni samples as compared to Cu
samples. The electrical conductivity is generally improved by Ni,
while addition of Cu improved it only in the over doped region (≥
0.10). These results are discussed in terms of the difference of
valency and ferromagnetic ordering for both dopants as compared to
undoped sample.
Abstract: Training with Functional Electrical Stimulation (FES)
has both physiological and psychological benefits for spinal cord
injured subjects. Commonly used methods for quantification of
spasticity have shown controversial reliability. In this study we
propose a method for quick determination of spasticity in spinal cord
injured subjects on a cycling and measurement system. 23 patients
did training sessions on an instrumented mobile FES cycle three
times a week over two months as part of their clinical rehabilitation
program. Spasticity (MAS) and the legs resistance to the pedaling
motion were assessed before and after the FES training and
measurements were done on the subjects ability to pedal with our
without motor assistance. Measurements with test persons with
incomplete spastic paraplegia have shown that spasticity is decreased
after a 30 min cycling training with functional electrical stimulation
(FES).
Abstract: Pepper spray use has gained momentum since 1992
and although the active ingredient is readily available, it is considered
a weapon with restricted use in many regions, including The
Bahamas. In light of controversy in the literature regarding the
severity of presenting respiration complaints among individuals postacute
exposure of pepper spray inhalation, this descriptive case series
study was conducted to assess the respiratory status of persons
evaluated during a mass casualty in The Bahamas. Parameters noted
were patients- demographics and respiration severity determined via
clinical examination findings, disposition and follow-up review of the
20 persons. Their most common complaint was difficulty breathing
post exposure. Two required admission and stayed for
Abstract: This paper describes dynamic analysis using proposed
fast finite element method for a shock absorbing structure including a
sponge. The structure is supported by nonlinear concentrated springs.
The restoring force of the spring has cubic nonlinearity and linear
hysteresis damping. To calculate damping properties for the structures
including elastic body and porous body, displacement vectors as
common unknown variable are solved under coupled condition. Under
small amplitude, we apply asymptotic method to complex eigenvalue
problem of this system to obtain modal parameters. And then
expressions of modal loss factor are derived approximately. This
approach was proposed by one of the authors previously. We call this
method as Modal Strain and Kinetic Energy Method (MSKE method).
Further, using the modal loss factors, the discretized equations in
physical coordinate are transformed into the nonlinear ordinary
coupled equations using normal coordinate corresponding to linear
natural modes. This transformation yields computation efficiency. As
a numerical example of a shock absorbing structures, we adopt double
skins with a sponge. The double skins are supported by nonlinear
concentrated springs. We clarify influences of amplitude of the input
force on nonlinear and chaotic responses.
Abstract: Sign language is used by the deaf and hard of hearing people for communication. Automatic sign language recognition is a challenging research area since sign language often is the only way of communication for the deaf people. Sign language includes different components of visual actions made by the signer using the hands, the face, and the torso, to convey his/her meaning. To use different aspects of signs, we combine the different groups of features which have been extracted from the image frames recorded directly by a stationary camera. We combine the features in two levels by employing three techniques. At the feature level, an early feature combination can be performed by concatenating and weighting different feature groups, or by concatenating feature groups over time and using LDA to choose the most discriminant elements. At the model level, a late fusion of differently trained models can be carried out by a log-linear model combination. In this paper, we investigate these three combination techniques in an automatic sign language recognition system and show that the recognition rate can be significantly improved.
Abstract: The objective of this work is to produce heterotrophic
microalgal lipid in flask-batch fermentation. Chlorella sp. KKU-S2
supported maximum values of 0.374 g/L/d, 0.478 g lipid/g cells, and
0.112 g/L/d for volumetric lipid production rate, and specific yield of
lipid, and specific rate of lipid production, respectively when culture
was performed on BG-11 medium supplemented with 50g/L glucose.
Among the carbon sources tested, maximum cell yield coefficient
(YX/S, g/L), maximum specific yield of lipid (YP/X, g lipid/g cells) and
volumetric lipid production rate (QP, g/L/d) were found of 0.728,
0.237, and 0.619, respectively, using sugarcane molasses as carbon
source. The main components of fatty acid from extracted lipid were
palmitic acid, stearic acid, oleic acid and linoleic acid which similar
to vegetable oils and suitable for biodiesel production.
Abstract: Hand gesture is an active area of research in the vision
community, mainly for the purpose of sign language recognition and
Human Computer Interaction. In this paper, we propose a system to
recognize alphabet characters (A-Z) and numbers (0-9) in real-time
from stereo color image sequences using Hidden Markov Models
(HMMs). Our system is based on three main stages; automatic segmentation
and preprocessing of the hand regions, feature extraction
and classification. In automatic segmentation and preprocessing stage,
color and 3D depth map are used to detect hands where the hand
trajectory will take place in further step using Mean-shift algorithm
and Kalman filter. In the feature extraction stage, 3D combined features
of location, orientation and velocity with respected to Cartesian
systems are used. And then, k-means clustering is employed for
HMMs codeword. The final stage so-called classification, Baum-
Welch algorithm is used to do a full train for HMMs parameters.
The gesture of alphabets and numbers is recognized using Left-Right
Banded model in conjunction with Viterbi algorithm. Experimental
results demonstrate that, our system can successfully recognize hand
gestures with 98.33% recognition rate.
Abstract: Social, mobility and information aggregation inside
business environment need to converge to reach the next step of
collaboration to enhance interaction and innovation. The following
article is based on the “Assemblage" concept seen as a framework to
formalize new user interfaces and applications. The area of research
is the Energy Social Business Environment, especially the Energy
Smart Grids, which are considered as functional and technical
foundations of the revolution of the Energy Sector of tomorrow. The
assemblages are modelized by means of mereology and simplicial
complexes. Its objective is to offer new central attention and
decision-making tools to end-users.
Abstract: Study fluid flow and heat transfer characteristics of
microchannel in a primary Cross-corrugated(CC) surface recuperators
with corrugations and without corrugations, using CFD method. The
pitch-over-height ratios P/H of Cross-corrugated (CC) surface is from
1.5 to 4.0, included angles β=75º. The study was performed using CFD
software FLUENT to create unit model and simulate fluid
temperature, velocity, heat transfer coefficient and other parameters.
The results from these simulations were compared to experimental
data. It is concluded that, when the Reynolds number is constant, if
increase P/H, j/f will decrease, also the decreasing trend will become
weak. Under the condition of P/H=2.2, if increase the inlet velocity j/f
will decrease; in addition, the heat transfer performance in surface
with corrugation will increase 10% compared to that without
corrugation. The study results can provide the basis to optimize the
design, select the type of heat transfer surface, the scale structure, and
heat-transfer surface arrangement for recuperators.
Abstract: The operating control parameters of injection
flushing type of electrical discharge machining process on stainless
steel 304 workpiece using copper tools are being optimized
according to its individual machining characteristic i.e. Electrode
Wear Ratio (EWR). Higher EWR would give bad dimensional
precision for the EDM machined workpiece because of high
electrode wear. Hence, the quality characteristic for EWR is set to
lower-the-better to achieve the optimum dimensional precision for
the machined workpiece. Taguchi method has been used for the
construction, layout and analysis of the experiment for EWR
machining characteristic. The use of Taguchi method in the
experiment saves a lot of time and cost of preparing and machining
the experiment samples. Therefore, an L18 Orthogonal array
which was the fundamental component in the statistical design of
experiments has been used to plan the experiments and Analysis of
Variance (ANOVA) is used to determine the optimum machining
parameters for this machining characteristic. The control
parameters selected for this optimization experiments are polarity,
pulse on duration, discharge current, discharge voltage, machining
depth, machining diameter and dielectric liquid pressure. The
result had shown that negative polarity machining parameter
setting will decreases EWR.
Abstract: In recent times there has been a growing interest in the
development of quasi-two-dimensional niobium pentoxide (Nb2O5)
as a semiconductor for the potential electronic applications such as
capacitors, filtration, dye-sensitised solar cells and gas sensing
platforms. Therefore once the purpose is established, Nb2O5 can be
prepared in a number of nano- and sub-micron-structural
morphologies that include rods, wires, belts and tubes. In this study
films of Nb2O5 were prepared on gold plated silicon substrate using
spin-coating technique and subsequently by mechanical exfoliation.
The reason this method was employed was to achieve layers of less
than 15nm in thickness. The sintering temperature of the specimen
was 800oC. The morphology and structural characteristics of the
films were analyzed by Atomic Force Microscopy (AFM), Raman
Spectroscopy, X-ray Photoelectron Spectroscopy (XPS).
Abstract: Climate change is a cumulative change in weather
patterns over a period of time. Trend analysis using non-parametric
Mann-Kendall test may help to determine the existence and
magnitude of any statistically significant trend in the climatic data.
Another index called Sen slope may be used to quantify the
magnitude of such trends. A toolbar extension to ESRI ArcGIS
named Arc Trends has been developed in this study for performing
the above mentioned tasks. To study the temporal trend of
meteorological parameters, 32 years (1971-2002) monthly
meteorological data were collected for 133 selected stations over
different agro-ecological regions of India. Both the maximum and
minimum temperatures were found to be rising. A significant
increasing trend in the relative humidity and a consistent significant
decreasing trend in the wind speed all over the country were found.
However, a general increase in rainfall was not found in recent years.
Abstract: Hydraulic conductivity is one parameter important for predicting the movement of water and contaminants dissolved in the water through the soil. The hydraulic conductivity is measured on soil samples in the lab and sometimes tests carried out in the field. The hydraulic conductivity has been related to soil particle diameter by a number of investigators. In this study, 25 set of soil samples with sand texture. The results show approximately success in predicting hydraulic conductivity from particle diameters data. The following relationship obtained from multiple linear regressions on data (R2 = 0.52): Where d10, d50 and d60, are the soil particle diameter (mm) that 10%, 50% and 60% of all soil particles are finer (smaller) by weight and Ks, saturated hydraulic conductivity is expressed in m/day. The results of regression analysis showed that d10 play a more significant role with respect to Ks, saturated hydraulic conductivity (m/day), and has been named as the effective parameter in Ks calculation.
Abstract: In this paper, an attempt has been made to obtain nonsensitive
solutions in the multi-objective optimization of a
photovoltaic/thermal (PV/T) air collector. The selected objective
functions are overall energy efficiency and exergy efficiency.
Improved thermal, electrical and exergy models are used to calculate
the thermal and electrical parameters, overall energy efficiency,
exergy components and exergy efficiency of a typical PV/T air
collector. A computer simulation program is also developed. The
results of numerical simulation are in good agreement with the
experimental measurements noted in the previous literature. Finally,
multi-objective optimization has been carried out under given
climatic, operating and design parameters. The optimized ranges of
inlet air velocity, duct depth and the objective functions in optimal
Pareto front have been obtained. Furthermore, non-sensitive solutions
from energy or exergy point of view in the results of multi-objective
optimization have been shown.
Abstract: Hot tear cracking and residual stress are two different consequences of thermal stress both of which can be considered as casting problem. The purpose of the present study is simulation of the effect of casting shape characteristic on hot tearing and residual stress. This study shows that the temperature range for simulation of hot tearing and residual stress are different. In this study, in order to study the development of thermal stress and to predict the hot tearing and residual stress of shaped casting, MAGMASOFT simulation program was used. The strategy of this research was the prediction of hot tear location using pinpointing hot spot and thermal stress concentration zones. The results shows that existing of stress concentration zone increases the hot tearing probability and consequently reduces the amount of remaining residual stress in casting parts.
Abstract: The main idea behind in network aggregation is that,
rather than sending individual data items from sensors to sinks,
multiple data items are aggregated as they are forwarded by the
sensor network. Existing sensor network data aggregation techniques
assume that the nodes are preprogrammed and send data to a central
sink for offline querying and analysis. This approach faces two major
drawbacks. First, the system behavior is preprogrammed and cannot
be modified on the fly. Second, the increased energy wastage due to
the communication overhead will result in decreasing the overall
system lifetime. Thus, energy conservation is of prime consideration
in sensor network protocols in order to maximize the network-s
operational lifetime. In this paper, we give an energy efficient
approach to query processing by implementing new optimization
techniques applied to in-network aggregation. We first discuss earlier
approaches in sensors data management and highlight their
disadvantages. We then present our approach “Energy Efficient
Indexed Aggregation" (EEIA) and evaluate it through several
simulations to prove its efficiency, competence and effectiveness.
Abstract: In this paper an open agent-based modular framework
for personalized and adaptive curriculum generation in e-learning
environment is proposed. Agent-based approaches offer several
potential advantages over alternative approaches. Agent-based
systems exhibit high levels of flexibility and robustness in dynamic
or unpredictable environments by virtue of their intrinsic autonomy.
The presented framework enables integration of different types of
expert agents, various kinds of learning objects and user modeling
techniques. It creates possibilities for adaptive e-learning process.
The KM e-learning system is in a process of implementation in
Varna Free University and will be used for supporting the
educational process at the University.
Abstract: A computational study at the level density functional theory (DFT) was carried out to investigate the influences of Si and C-doping on the 14N and 27Al quadrupole coupling constant in the (10, 0) zigzag single ? walled Aluminum-Nitride nanotube (AlNNT). To this aim, a 1.16nm, length of AlNNT consisting of 40 Al atoms and 40 N atoms were selected where the end atoms are capped by hydrogen atom. To follow the purpose, three Si atoms and three C atoms were doped instead of three Al atoms and three N atoms as a central ring in the surface of the Si and C-doped AlNNT. At first both of systems optimized at the level of BLYP method and 6-31G (d) basis set and after that, the NQR parameters were calculated at the level BLYP method and 6-311+G** basis set in two optimized forms. The calculate CQ values for both optimized AlNNT systems, raw and Si and C-doped, reveal different electronic environments in the mentioned systems. It was also demonstrated that the end nuclei have the largest CQ values in both considered AlNNT systems. All the calculations were carried out using Gaussian 98 package of program.
Abstract: Simulations of magnetic microstructure in elliptical
Permalloy elements used for controlled motion of magnetic particles
are discussed. The saturating field of the elliptical elements was
studied with respect to lateral dimensions for one-vortex, cross-tie,
diamond and double-diamond states as initial zero-field domain
configurations. With aspect ratio of 1:3 the short axis was varied
from 125 nm to 1000 nm, whereas the thickness was kept constant at
50 nm.
Abstract: This study proposes a hybrid minimal repair policy
which combines periodic maintenance policy with age-based maintenance policy for a serial production system. Parameters of such policy are defined as and which indicate as hybrid minimal
repair time and planned preventive maintenance time
respectively . Under this hybrid policy, the system is
repaired minimally if it fails during , . A perfect repair is
conducted on the first failure after at any machines. At the same time, we take opportunity to advance the preventive maintenance of
other machines simultaneously. If the system is still operating
properly up to , then the preventive maintenance is carried out as its
predetermined schedule. For a given , we obtain the optimal value which minimizes the expected cost per time unit. Numerical
example is presented to illustrate the properties of the optimal solution.