Abstract: The aim of this study is to analyze influence of
differences of heat insulation methods on indoor thermal environment and comfort of apartment buildings.
This study analyzes indoor thermal environment and comfort on units of apartment buildings using calculation software "THERB" and
compares three different kinds of heat insulation methods. Those are
outside insulation on outside walls, inside insulation on outside walls and interior insulation. In terms of indoor thermal environment, outside insulation is the best to stabilize room temperature. In winter, room temperature on
outside insulation after heating is higher than other and it is kept 3-5 degrees higher through all night. But the surface temperature with
outside insulation did not dramatically increase when heating was used, which was 3 to 5oC lower than the temperature with other
insulation. The PMV of interior insulation fall nearly range of comfort when the heating and cooling was use.
Abstract: Mechanical and water transport properties of high
performance concrete (HPC) containing natural zeolite as partial
replacement of Portland cement are studied. Experimental results
show that in the investigated mixes the use of natural zeolite leads to
an increase of porosity, decrease of compressive strength and
increase of moisture diffusivity and water vapor diffusion coefficient,
as compared with the reference HPC. However, for the replacement
level up to 20% of the mass of Portland cement the concretes still
maintain their high performance character and exhibit acceptable
water transport properties. Therefore, natural zeolite can be
considered an environmental friendly binder with a potential to
replace a part of Portland cement in concrete in building industry.
Abstract: The 'wind-rain' house has a courtyard with glazed
roof, which allows more direct sunlight to come into indoor spaces
during the winter. The glazed roof can be partially opened or closed
and automatically controlled to provide natural ventilation in order to
adjust for indoor thermal conditions and the roof area can be shaded
by reflective insulation materials during the summer. Two field
studies for evaluating indoor thermal conditions of the two 'windrain'
houses have been carried out by author in 2009 and 2010.
Indoor and outdoor air temperature and relative humidity adjacent to
floor and ceiling of the two sample houses were continuously tested
at 15-minute intervals, 24 hours a day during the winter months.
Based on field study data, this study investigates relationships
between building design and indoor thermal condition of the 'windrain'
house to improve the future house design for building thermal
comfort and energy efficiency
Abstract: Building life cycle will never be excused from the existence of defects and deterioration. They are common problems in building, existed in newly build or in aged building. Buildings constructed from wood are indeed affected by its agent and serious defects and damages can reduce values to a building. In repair works, it is important to identify the causes and repair techniques that best suites with the condition. This paper reviews the conservation of traditional timber mosque in Malaysia comprises the concept, principles and approaches of mosque conservation in general. As in conservation practice, wood in historic building can be conserved by using various restoration and conservation techniques which this can be grouped as Fully and Partial Replacement, Mechanical Reinforcement, Consolidation by Impregnation and Reinforcement, Removing Paint and also Preservation of Wood and Control Insect Invasion, as to prolong and extended the function of a timber in a building. It resulted that the common techniques adopted in timber mosque conservation are from the conventional ways and the understanding of the repair technique requires the use of only preserve wood to prevent the future immature defects.
Abstract: Building maintenance plays an important role among other activities in building operation. Building defect and damages are part of the building maintenance 'bread and butter' as their input indicated in the building inspection is very much justified, particularly as to determine the building performance. There will be no escape route or short cut from building maintenance work. This study attempts to identify a competitive performance that translates the Critical Success Factor achievements and satisfactorily meet the university-s expectation. The quality and efficiency of maintenance management operation of building depends, to some extent, on the building condition information, the expectation from the university sector and the works carried out for each maintenance activity. This paper reviews the critical success factor in building maintenance management practice for university sectors from four (4) perspectives which include (1) customer (2) internal processes (3) financial and (4) learning and growth perspective. The enhancement of these perspectives is capable to reach the maintenance management goal for a better living environment in university campus.
Abstract: Globalization, supported by information and
communication technologies, changes the rules of competitiveness
and increases the significance of information, knowledge and
network cooperation. In line with this trend, the need for efficient
trust-building tools has emerged. The absence of trust building
mechanisms and strategies was identified within several studies.
Through trust development, participation on e-business network and
usage of network services will increase and provide to SMEs new
economic benefits. This work is focused on effective trust building
strategies development for electronic business network platforms.
Based on trust building mechanism identification, the questionnairebased
analysis of its significance and minimum level of requirements
was conducted. In the paper, we are confirming the trust dependency
on e-Skills which play crucial role in higher level of trust into the
more sophisticated and complex trust building ICT solutions.
Abstract: Mobile adhoc network (MANET) is a collection of
mobile devices which form a communication network with no preexisting
wiring or infrastructure. Multiple routing protocols have
been developed for MANETs. As MANETs gain popularity, their
need to support real time applications is growing as well. Such
applications have stringent quality of service (QoS) requirements
such as throughput, end-to-end delay, and energy. Due to dynamic
topology and bandwidth constraint supporting QoS is a challenging
task. QoS aware routing is an important building block for QoS
support. The primary goal of the QoS aware protocol is to determine
the path from source to destination that satisfies the QoS
requirements. This paper proposes a new energy and delay aware
protocol called energy and delay aware TORA (EDTORA) based on
extension of Temporally Ordered Routing Protocol (TORA).Energy
and delay verifications of query packet have been done in each node.
Simulation results show that the proposed protocol has a higher
performance than TORA in terms of network lifetime, packet
delivery ratio and end-to-end delay.
Abstract: This paper has examined the energy consumption characteristics in six different buildings including apartments, offices, commercial buildings, hospitals, hotels and educational facilities. Then 5-hectare (50000m2) development site for respective building-s type has been assumed as case study to evaluate the introduction effect of Combined Heat and Power (CHP). All kinds of CHP systems with different distributed generation technologies including Gas Turbine (GT), Gas Engine (GE), Diesel Engine (DE), Solid Oxide Fuel Cell (SOFC) and Polymer Electrolyte Fuel Cell (PEFC), have been simulated by using HEATMAP, CHP system analysis software. And their primary energy utilization efficiency, energy saving ratio and CO2 reduction ratio have evaluated and compared respectively. The results can be summarized as follows: Various buildings have their special heat to power ratio characteristics. Matching the heat to power ratio demanded from an individual building with that supplied from a CHP system is very important. It is necessary to select a reasonable distributed generation technologies according to the load characteristics of various buildings. Distributed generation technologies with high energy generating efficiency and low heat to power ratio, like SOFC and PEFC is more reasonable selection for Building Combined Heat and Power (BCHP). CHP system is an attractive option for hotels, hospitals and apartments in Japan. The users can achieve high energy saving and environmental benefit by introducing a CHP systems. In others buildings, especially like commercial buildings and offices, the introduction of CHP system is unreasonable.
Abstract: Calculations of energy efficiency of several AACbased
building envelopes under different climatic conditions are
presented. As thermal insulating materials, expanded polystyrene and
hydrophobic and hydrophilic mineral wools are assumed. The
computations are accomplished using computer code HEMOT
developed at Department of Materials Engineering, Faculty of Civil
Engineering at the Czech Technical University in Prague. The
climatic data of Athens, Kazan, Oslo, Prague and Reykjavík are
obtained using METEONORM software.
Abstract: The objective of this study is to investigate the effect of adding coal to obtain insulating ceramic product. The preparation of mixtures is achieved with 04 types of different masse compositions, consisting of gray and yellow clay, and coal. Analyses are performed on local raw materials by adding coal as additive. The coal content varies from 5 to 20 % in weight by varying the size of coal particles ranging from 0.25mm to 1.60mm.
Initially, each natural moisture content of a raw material has been determined at the temperature of 105°C in a laboratory oven. The Influence of low-coal content on absorption, the apparent density, the contraction and the resistance during compression have been evaluated. The experimental results showed that the optimized composition could be obtained by adding 10% by weight of coal leading thus to insulating ceramic products with water absorption, a density and resistance to compression of 9.40 %, 1.88 g/cm3, 35.46 MPa, respectively. The results show that coal, when mixed with traditional raw materials, offers the conditions to be used as an additive in the production of lightweight ceramic products.
Abstract: Among various testing methodologies, Built-in Self-
Test (BIST) is recognized as a low cost, effective paradigm. Also,
full adders are one of the basic building blocks of most arithmetic
circuits in all processing units. In this paper, an optimized testable 2-
bit full adder as a test building block is proposed. Then, a BIST
procedure is introduced to scale up the building block and to generate
a self testable n-bit full adders. The target design can achieve 100%
fault coverage using insignificant amount of hardware redundancy.
Moreover, Overall test time is reduced by utilizing polymorphic
gates and also by testing full adder building blocks in parallel.
Abstract: The search for factors that influence user behavior has remained an important theme for both the academic and practitioner Information Systems Communities. In this paper we examine relevant user behaviors in the phase after adoption and investigate two factors that are expected to influence such behaviors, namely User Involvement (UI) and Personal Innovativeness in IT (PIIT). We conduct a field study to examine how these factors influence postadoption behavior and how they are interrelated. Building on theoretical premises and prior empirical findings, we propose and test two alternative models of the relationship between these factors. Our results reveal that the best explanation of post-adoption behavior is provided by the model where UI and PIIT independently influence post-adoption behavior. Our findings have important implications for research and practice. To that end, we offer directions for future research.
Abstract: The main aim of this paper was to investigate the
existing architecture in Cyprus, and thus identify and describe the
overall architectural rationale of the built environment. In Cyprus,
where individuals live in a society that reflects postmodern
paradigms rather than modern ones, the existing built environment
has many different reflections of the structure of its society.
Abstract: This paper discusses the implementation of the Kalman
Filter along with the Global Positioning System (GPS) for indoor
robot navigation. Two dimensional coordinates is used for the map
building, and refers to the global coordinate which is attached to the
reference landmark for position and direction information the robot
gets. The Discrete Kalman Filter is used to estimate the robot position,
project the estimated current state ahead in time through time update
and adjust the projected estimated state by an actual measurement at
that time via the measurement update. The navigation test has been
performed and has been found to be robust.
Abstract: For investigations of electromagnetic field
distributions in biological structures by Finite Element Method
(FEM), a method for automatic 3D model building of human
anatomical objects is developed. Models are made by meshed
structures and specific electromagnetic material properties for each
tissue type. Mesh is built according to specific FEM criteria for
achieving good solution accuracy. Several FEM models of
anatomical objects are built. Formulation using magnetic vector
potential and scalar electric potential (A-V, A) is used for modeling
of electromagnetic fields in human tissue objects. The developed
models are suitable for investigations of electromagnetic field
distributions in human tissues exposed in external fields during
magnetic stimulation, defibrillation, impedance tomography etc.
Abstract: In order to consider the effects of the higher modes in
the pushover analysis, during the recent years several multi-modal
pushover procedures have been presented. In these methods the
response of the considered modes are combined by the square-rootof-
sum-of-squares (SRSS) rule while application of the elastic modal
combination rules in the inelastic phases is no longer valid. In this
research the feasibility of defining an efficient alternative
combination method is investigated. Two steel moment-frame
buildings denoted SAC-9 and SAC-20 under ten earthquake records
are considered. The nonlinear responses of the structures are
estimated by the directed algebraic combination of the weighted
responses of the separate modes. The weight of the each mode is
defined so that the resulted response of the combination has a
minimum error to the nonlinear time history analysis. The genetic
algorithm (GA) is used to minimize the error and optimize the weight
factors. The obtained optimal factors for each mode in different cases
are compared together to find unique appropriate weight factors for
each mode in all cases.
Abstract: This paper is part of an ongoing research on the
development of systemic maintenance management model Malaysian
university buildings. In order to achieve this aim, there is a need to
develop a performance model against which services are measure.
Measuring performance is a significant part of maintenance
management service delivery. Maintenance organization needs to
know where they are in order to provide user-driven services and to
enhance productivity. The aim of this paper is to formulate a
template or model for university maintenance organization in
Malaysia. The model is based on literature review and survey
questionnaire and has been validated. Through grounded theory, this
paper developed a 8 points matrix for the university maintenance
organizations for measuring and improving their service delivery.
The potential of the model is guide and assists towards providing
value added service delivery through initiating maintenance
according to user value system rather than on the condition of the
building.
Abstract: In Thailand, both the 1997 and the current 2007 Thai Constitutions have mentioned the establishment of independent organizations as a new mechanism to play a key role in proposing policy recommendations to national decision-makers in the interest of collective consumers. Over the last ten years, no independent organizations have yet been set up. Evidently, nobody could point out who should be key players in establishing provincial independent consumer bodies. The purpose of this study was to find definitive stakeholders in establishing and developing independent consumer bodies in a Thai context. This was a cross-sectional study between August and September 2007, using a postal questionnaire with telephone follow-up. The questionnaire was designed and used to obtain multiple stakeholder assessment of three key attributes (power, interest and influence). Study population was 153 stakeholders associated with policy decision-making, formulation and implementation processes of civil-based consumer protection in pilot provinces. The population covered key representatives from five sectors (academics, government officers, business traders, mass media and consumer networks) who participated in the deliberative forums at 10 provinces. A 49.7% response rate was achieved. Data were analyzed, comparing means of three stakeholder attributes and classification of stakeholder typology. The results showed that the provincial health officers were the definitive stakeholders as they had legal power, influence and interest in establishing and sustaining the independent consumer bodies. However, only a few key representatives of the provincial health officers expressed their own paradigm on the civil-based consumer protection. Most provincial health officers put their own standpoint of building civic participation at only a plan-implementation level. For effective policy implementation by the independent consumer bodies, the Thai government should provide budgetary support for the operation of the provincial health officers with their paradigm shift as well as their own clarified standpoint on corporate governance.
Abstract: This paper describes the architectural design
considerations for building a new class of application, a Personal
Knowledge Integrator and a particular example a Knowledge Theatre.
It then supports this description by describing a scenario of a child
acquiring knowledge and how this process could be augmented by
the proposed architecture and design of a Knowledge Theatre. David
Merrill-s first “principles of instruction" are kept in focus to provide
a background to view the learning potential.
Abstract: Bridge is an architectural symbol in Iran as Badgir
(wind catcher); fire temples and arch are vaults are such. Therefore, from the very old ages, construction of bridges in Iran has mixed with
architecture, social customs, alms and charity and holiness. Since long ago, from Mad, Achaemenid, Parthian and Sassanid times which construction of bridges got an inseparable relation with social dependency and architecture, based on those dependency bridges and
dams got holy names; as Dokhtar castle and Dokhtar bridges were constructed. This method continued even after Islam and whenever
Iranians got free from political fights and the immunity of roads were established the bridge construction did also prospered. In ancient
times bridge construction passes through it growing and completion process and in Sassanid time in some way it reached to the peak of art
and glory; as after Islam especially during 4th. century (Arab calendar) it put behind a period of glory and in Safavid time it
reached to an exceptional glory and magnificence by constructing
glorious bridges on Zayandeh Roud River in Isfahan.
Having a combined style and changeability into bridge barrier, some of these bridges develop into magnificent constructions. The
sustainable structures, mentioned above, are constructed for various
reasons as follows: connecting two sides of a river, storing water,
controlling floods, using water energy to operate water windmills, making lanes of streams for farms- use, and building recreational
places for people, etc. These studies carried in bridges reveals the fact
that in construction and designing mentioned above, lots of
technological factors have been taken into consideration such as
exceeding floods in the rives, hydraulic and hydrology of the rivers and bridges, geology, foundation, structure, construction material, and adopting appropriate executing methods, all of which are being analyzed in this article.