Abstract: One of the major causes of voltage instability is the reactive power limit of the system. Improving the system's reactive power handling capacity via Flexible AC transmission System (FACTS) devices is a remedy for prevention of voltage instability and hence voltage collapse. In this paper, the effects of SVC and STATCOM in Static Voltage Stability Margin Enhancement will be studied. AC and DC representations of SVC and STATCOM are used in the continuation power flow process in static voltage stability study. The IEEE-14 bus system is simulated to test the increasing loadability. It is found that these controllers significantly increase the loadability margin of power systems.
Abstract: Pressure wave velocity in a hydraulic system was
determined using piezo pressure sensors without removing fluid from
the system. The measurements were carried out in a low pressure
range (0.2 – 6 bar) and the results were compared with the results of
other studies. This method is not as accurate as measurement with
separate measurement equipment, but the fluid is in the actual
machine the whole time and the effect of air is taken into
consideration if air is present in the system. The amount of air is
estimated by calculations and comparisons between other studies.
This measurement equipment can also be installed in an existing
machine and it can be programmed so that it measures in real time.
Thus, it could be used e.g. to control dampers.
Abstract: This article gives a short preview of the new software
created especially for palletizing process in automated production
systems. Each chapter of this article is about problem solving in
development of modules in Java programming language. First part
describes structure of the software, its modules and data flow
between them. Second part describes all deployment methods, which
are implemented in the software. Next chapter is about twodimensional
editor created for manipulation with objects in each
layer of the load and gives calculations for collision control. Module
of virtual reality used for three-dimensional preview and creation of
the load is described in the fifth chapter. The last part of this article
describes communication and data flow between control system of
the robot, vision system and software.
Abstract: The tubes in an Ammonia primary reformer furnace
operate close to the limits of materials technology in terms of the
stress induced as a result of very high temperatures, combined with
large differential pressures across the tube wall. Operation at tube
wall temperatures significantly above design can result in a rapid
increase in the number of tube failures, since tube life is very
sensitive to the absolute operating temperature of the tube. Clearly it
is important to measure tube wall temperatures accurately in order to
prevent premature tube failure by overheating.. In the present study,
the catalyst tubes in an Ammonia primary reformer has been modeled
taking into consideration heat, mass and momentum transfer as well
as reformer characteristics.. The investigations concern the effects of
tube characteristics and superficial tube wall temperatures on of the
percentage of heat flux, unconverted methane and production of
Hydrogen for various values of steam to carbon ratios. The results
show the impact of catalyst tubes length and diameters on the
performance of operating parameters in ammonia primary reformers.
Abstract: In this paper back-propagation artificial neural
network (BPANN) is employed to predict the limiting drawing ratio
(LDR) of the deep drawing process. To prepare a training set for
BPANN, some finite element simulations were carried out. die and
punch radius, die arc radius, friction coefficient, thickness, yield
strength of sheet and strain hardening exponent were used as the
input data and the LDR as the specified output used in the training of
neural network. As a result of the specified parameters, the program
will be able to estimate the LDR for any new given condition.
Comparing FEM and BPANN results, an acceptable correlation was
found.
Abstract: This paper describes about dynamic reconfiguration to
miniaturize arithmetic circuits in general-purpose processor. Dynamic
reconfiguration is a technique to realize required functions by
changing hardware construction during operation. The proposed
arithmetic circuit performs floating-point arithmetic which is
frequently used in science and technology. The data format is
floating-point based on IEEE754. The proposed circuit is designed
using VHDL, and verified the correct operation by simulations and
experiments.
Abstract: In this manuscript, we discuss the problem of determining the optimum stratification of a study (or main) variable based on the auxiliary variable that follows a uniform distribution. If the stratification of survey variable is made using the auxiliary variable it may lead to substantial gains in precision of the estimates. This problem is formulated as a Nonlinear Programming Problem (NLPP), which turn out to multistage decision problem and is solved using dynamic programming technique.
Abstract: loss of feedwater accident is one of the frequently sever accidents in steam boiler facilities. It threatens the system structural integrity and generates serious hazards and economic loses. The safety analysis of the thermal installations, based extensively on the numeric simulation. The simulation analysis using realistic computer codes like Relap5/Mod3.2 will help understand steam boiler thermal-hydraulic behavior during normal and abnormal conditions. In this study, we are interested on the evaluation of the radiant steam boiler assessment and response to loss-of-feedwater accident. Pressure, temperature and flow rate profiles are presented in various steam boiler system components. The obtained results demonstrate the importance and capability of the Relap5/Mod3.2 code in the thermal-hydraulic analysis of the steam boiler facilities.
Abstract: This paper describes a newly designed decentralized
nonlinear control strategy to control a robot manipulator. Based on the
concept of the nonlinear state feedback theory and decentralized
concept is developed to improve the drawbacks in previous works
concerned with complicate intelligent control and low cost effective
sensor. The control methodology is derived in the sense of Lyapunov
theorem so that the stability of the control system is guaranteed. The
decentralized algorithm does not require other joint angle and velocity
information. Individual Joint controller is implemented using a digital
processor with nearly actuator to make it possible to achieve good
dynamics and modular. Computer simulation result has been
conducted to validate the effectiveness of the proposed control scheme
under the occurrence of possible uncertainties and different reference
trajectories. The merit of the proposed control system is indicated in
comparison with a classical control system.
Abstract: This paper presents a new methodology to select test
cases from regression test suites. The selection strategy is based on
analyzing the dynamic behavior of the applications that written in
any programming language. Methods based on dynamic analysis are
more safe and efficient. We design a technique that combine the code
based technique and model based technique, to allow comparing the
object oriented of an application that written in any programming
language. We have developed a prototype tool that detect changes
and select test cases from test suite.
Abstract: Gas flaring is one of the most GHG emitting sources in the oil and gas industries. It is also a major way for wasting such an energy that could be better utilized and even generates revenue. Minimize flaring is an effective approach for reducing GHG emissions and also conserving energy in flaring systems. Integrating waste and flared gases into the fuel gas networks (FGN) of refineries is an efficient tool. A fuel gas network collects fuel gases from various source streams and mixes them in an optimal manner, and supplies them to different fuel sinks such as furnaces, boilers, turbines, etc. In this article we use fuel gas network model proposed by Hasan et al. as a base model and modify some of its features and add constraints on emission pollution by gas flaring to reduce GHG emissions as possible. Results for a refinery case study showed that integration of flare gas stream with waste and natural gas streams to construct an optimal FGN can significantly reduce total annualized cost and flaring emissions.
Abstract: There are several approaches in trying to solve the
Quantitative 1Structure-Activity Relationship (QSAR) problem.
These approaches are based either on statistical methods or on
predictive data mining. Among the statistical methods, one should
consider regression analysis, pattern recognition (such as cluster
analysis, factor analysis and principal components analysis) or partial
least squares. Predictive data mining techniques use either neural
networks, or genetic programming, or neuro-fuzzy knowledge. These
approaches have a low explanatory capability or non at all. This
paper attempts to establish a new approach in solving QSAR
problems using descriptive data mining. This way, the relationship
between the chemical properties and the activity of a substance
would be comprehensibly modeled.
Abstract: In this research, a systematic investigation was carried out to determine the optimum conditions of HDS reactor. Moreover, a suitable model was developed for a rigorous RTO (real time optimization) loop of HDS (Hydro desulfurization) process. A systematic experimental series was designed based on CCD (Central Composite design) and carried out in the related pilot plant to tune the develop model. The designed variables in the experiments were Temperature, LHSV and pressure. However, the hydrogen over fresh feed ratio was remained constant. The ranges of these variables were respectively equal to 320-380ºC, 1- 21/hr and 50-55 bar. a power law kinetic model was also developed for our further research in the future .The rate order and activation energy , power of reactant concentration and frequency factor of this model was respectively equal to 1.4, 92.66 kJ/mol and k0=2.7*109 .
Abstract: Many real-world data sets consist of a very high dimensional feature space. Most clustering techniques use the distance or similarity between objects as a measure to build clusters. But in high dimensional spaces, distances between points become relatively uniform. In such cases, density based approaches may give better results. Subspace Clustering algorithms automatically identify lower dimensional subspaces of the higher dimensional feature space in which clusters exist. In this paper, we propose a new clustering algorithm, ISC – Intelligent Subspace Clustering, which tries to overcome three major limitations of the existing state-of-art techniques. ISC determines the input parameter such as є – distance at various levels of Subspace Clustering which helps in finding meaningful clusters. The uniform parameters approach is not suitable for different kind of databases. ISC implements dynamic and adaptive determination of Meaningful clustering parameters based on hierarchical filtering approach. Third and most important feature of ISC is the ability of incremental learning and dynamic inclusion and exclusions of subspaces which lead to better cluster formation.
Abstract: We present a prototype interactive (hyper) map of strategic, tactical, and logistic options for Supply Chain Management. The map comprises an anthology of options, broadly classified within the strategic spectrum of efficiency versus responsiveness, and according to logistic and cross-functional drivers. They are exemplified by cases in diverse industries. We seek to get all these information and ideas organized to help supply chain managers identify effective choices for specific business environments. The key and innovative linkage we introduce is the configuration of competitive forces. Instead of going through seemingly endless and isolated cases and wondering how one can borrow from them, we aim to provide a guide by force comparisons. The premise is that best practices in a different industry facing similar forces may be a most productive resource in supply chain design and planning. A prototype template is demonstrated.
Abstract: Paced Auditory Serial Addition Test (PASAT) has
been used as a common research tool for different neurological
disorders like Multiple Sclerosis. Recently, technology let
researchers to introduce a new versions of the visual test, the paced
visual serial addition test (PVSAT). In this paper, the computerized
version of these two tests is introduced. Beside the number of true
responses are interpreted, the reaction time of subjects are calculated
by the software. We hypothesize that paying attention to the reaction
time may be valuable. For this purpose, sixty eight female normal
subjects and fifty eight male normal subjects are enrolled in the
study. We investigate the similarity between the PASAT3 and
PVSAT3 in number of true responses and the new criterion (the
average reaction time of each subject). The similarity between two
tests were rejected (p-value = 0.000) which means that these two test
differ. The effect of sex in the tests were not approved since the pvalues
of different between PASAT3 and PVSAT3 in both sex is the
same (p-value = 0.000) which means that male and female subjects
performed the tests at no different level of performance. The new
criterion shows a negative correlation with the age which offers aged
normal subjects may have the same number of true responses as the
young subjects but they have latent responses. This will give prove
for the importance of reaction time.
Abstract: The noteworthy point in the advancement of Brain Machine Interface (BMI) research is the ability to accurately extract features of the brain signals and to classify them into targeted control action with the easiest procedures since the expected beneficiaries are of disabled. In this paper, a new feature extraction method using the combination of adaptive band pass filters and adaptive autoregressive (AAR) modelling is proposed and applied to the classification of right and left motor imagery signals extracted from the brain. The introduction of the adaptive bandpass filter improves the characterization process of the autocorrelation functions of the AAR models, as it enhances and strengthens the EEG signal, which is noisy and stochastic in nature. The experimental results on the Graz BCI data set have shown that by implementing the proposed feature extraction method, a LDA and SVM classifier outperforms other AAR approaches of the BCI 2003 competition in terms of the mutual information, the competition criterion, or misclassification rate.
Abstract: Prickly pear (Opuntia spp) fruit has received renewed
interest since it contains a betalain pigment that has an attractive
purple colour for the production of juice. Prickly pear juice was
prepared by homogenizing the fruit and treating the pulp with 48 g of
pectinase from Aspergillus niger. Titratable acidity was determined
by diluting 10 ml prickly pear juice with 90 ml deionized water and
titrating to pH 8.2 with 0.1 N NaOH. Brix was measured using a
refractometer and ascorbic acid content assayed
spectrophotometrically. Colour variation was determined
colorimetrically (Hunter L.a.b.). Hunter L.a.b. analysis showed that
the red purple colour of prickly pear juice had been affected by juice
treatments. This was indicated by low light values of colour
difference meter (CDML*), hue, CDMa* and CDMb* values. It was
observed that non-treated prickly pear juice had a high (colour
difference meter of light) CDML* of 3.9 compared to juice
treatments (range 3.29 to 2.14). The CDML* significantly (p
Abstract: The new architecture for quantum cellular
automata is offered. A QCA cell includes two layers nc-Si,
divided by a dielectric. Among themselves cells are connected
by the bridge from a conductive material. The comparison is
made between this and QCA, offered earlier by C. Lent's
group.
Abstract: The paper deals with the possibilities of modelling
vapour propagation of explosive substances in the FLUENT
software. With regard to very low tensions of explosive substance
vapours the experiment has been verified as exemplified by
mononitrotoluene. Either constant or time variable meteorological
conditions have been used for calculation. Further, it has been
verified that the eluent source may be time-dependent and may reflect
a real situation or the liberation rate may be constant. The execution
of the experiment as well as evaluation were clear and it could also
be used for modelling vapour and aerosol propagation of selected
explosive substances in the atmospheric boundary layer.