Abstract: Makishima and Mackenzie model was used to
simulation of acoustic properties (longitudinal and shear ultrasonic
wave velocities, elastic moduli theoretically for many tellurite and
borate glasses. The model was proposed mainly depending on the
values of the experimentally measured density, which are obtained
before. In this search work, we are trying to obtain the values of
densities of amorphous glasses (as the density depends on the
geometry of the network structure of these glasses). In addition, the
problem of simulating the slope of linear regression between the
experimentally determined bulk modulus and the product of packing
density and experimental Young's modulus, were solved in this
search work. The results showed good agreement between the
experimentally measured values of densities and both ultrasonic wave
velocities, and those theoretically determined.
Abstract: In this paper, we investigated the athermal pressure
behavior of the structural and elastic properties of scheelite BaWO4
phase up to 7 GPa using the ab initio pseudo-potential method. The
calculated lattice parameters pressure relation have been compared
with the experimental values and found to be in good agreement with
these results. Moreover, we present for the first time the investigation
of the elastic properties of this compound using the density functional
perturbation theory (DFPT). It is shown that this phase is
mechanically stable up to 7 GPa after analyzing the calculated elastic
constants. Other relevant quantities such as bulk modulus, pressure
derivative of bulk modulus, shear modulus; Young’s modulus,
Poisson’s ratio, anisotropy factors, Debye temperature and sound
velocity have been calculated. The obtained results, which are
reported for the first time to the best of the author’s knowledge, can
facilitate assessment of possible applications of the title material.
Abstract: We report herein the development and preliminary mechanical characterization of fully-dense multi-wall carbon nanotube (MWCNT)-reinforced ceramics and glasses based on a completely new methodology termed High Shear Compaction (HSC). The tubes are introduced and bound to the matrix grains by aid of polymeric binders to form flexible green bodies which are sintered and densified by spark plasma sintering to unprecedentedly high densities of 100% of the pure-matrix value. The strategy was validated across a PyrexTM glass / MWCNT composite while no identifiable factors limit application to other types of matrices. Nondestructive evaluation, based on ultrasonics, of the dynamic mechanical properties of the materials including elastic, shear and bulk modulus as well as Poisson’s ratio showed optimum property improvement at 0.5 %wt tube loading while evidence of nanoscalespecific energy dissipative characteristics acting complementary to nanotube bridging and pull-out indicate a high potential in a wide range of reinforcing and multifunctional applications.
Abstract: Physical properties of uranium dinitride (UN2) were
investigated in detail using first principle calculations based on
density functional theory (DFT). To study the strong correlation
effects due to 5f uranium valence electrons, the on-site coulomb
interaction correction U via the Hubbard-like term (DFT+U) was
employed. The UN2 structural, mechanical and thermodynamic
properties were calculated within DFT and Various U of DFT+U
approach.
The Perdew–Burke–Ernzerhof (PBE.5.2) version of the
generalized gradient approximation (GGA) is used to describe the
exchange-correlation with the projector-augmented wave (PAW)
pseudo potentials.
A comparative study shows that results are improved by using the
Hubbard formalism for a certain U value correction like the structural
parameter. For some physical properties the variation versus
Hubbard-U is strong like Young modulus but for others it is weakly
noticeable such as bulk modulus.
We noticed also that from U=7.5 eV, elastic results don’t agree
with the cubic cell because of the C44 values which turn out to be
negative.
Abstract: High resolution seismic reflection has recently been carried out on Zaria batholith, with the aim of characterizing the granitic Zaria batholiths in terms of its lithology. The geology of the area has revealed that the older granite outcrops in the vicinity of Zaria are exposures of a syntectonics to late-tectonic granite batholiths which intruded a crystalline gneissic basement during the Pan-African Orogeny. During the data acquisition the geophone were placed at interval of 1 m, variable offset of 1 and 10 m was used. The common midpoint (CMP) method with 12 fold coverage was employed for the survey. Analysis of the generated 3D surface of the p wave velocities from different profiles for densities and bulk modulus revealed that the rock material is more consolidated in South East part of the batholith and less consolidated in the North Western part. This was in conformity with earlier identified geology of the area, with the South Eastern part majorly of granitic outcrop, while the North Western part is characterized with the exposure of gneisses and thick overburden cover. The difference in lithology was also confirmed by the difference in seismic sections and Arial satellite photograph. Hence two major lithologies were identified, the granitic and gneisses complex which are characterized by gradational boundaries.
Abstract: Earphones and headphones, which are compact electro-acoustic transducers, tend to have a lot of acoustic absorption materials and porous materials known as dampers, which often have a large number of extremely small holes and narrow slits to inhibit the resonance of the vibrating system, because the air viscosity significantly affects the acoustic characteristics in such acoustic paths. In order to perform simulations using the finite element method (FEM), it is necessary to be aware of material characteristics such as the impedance and propagation constants of sound absorbing materials and porous materials. The transfer function is widely known as a measurement method for an acoustic tube with such physical properties, but literature describing the measurements at the upper limits of the audible range is yet to be found. The acoustic tube, which is a measurement instrument, must be made narrow, and the distance between the two sets of microphones must be shortened in order to take measurements of acoustic characteristics at higher frequencies. When such a tube is made narrow, however, the characteristic impedance has been observed to become lower than the impedance of air. This paper considers the cause of this phenomenon to be the effect of the air viscosity and describes an FEM analysis of an acoustic tube considering air viscosity to compare to the theoretical formula by including the effect of air viscosity in the theoretical formula for an acoustic tube.
Abstract: The aim of this research was to calculate the
mechanical properties of Pd3Rh and PdRh3 ordered alloys. The
molecular dynamics (MD) simulation technique was used to obtain
temperature dependence of the energy, the Yong modulus, the shear
modulus, the bulk modulus, Poisson-s ratio and the elastic stiffness
constants at the isobaric-isothermal (NPT) ensemble in the range of
100-325 K. The interatomic potential energy and force on atoms were
calculated by Quantum Sutton-Chen (Q-SC) many body potential.
Our MD simulation results show the effect of temperature on the
cohesive energy and mechanical properties of Pd3Rh as well as
PdRh3 alloys. Our computed results show good agreement with the
experimental results where they have been available.
Abstract: Pressure wave velocity in a hydraulic system was
determined using piezo pressure sensors without removing fluid from
the system. The measurements were carried out in a low pressure
range (0.2 – 6 bar) and the results were compared with the results of
other studies. This method is not as accurate as measurement with
separate measurement equipment, but the fluid is in the actual
machine the whole time and the effect of air is taken into
consideration if air is present in the system. The amount of air is
estimated by calculations and comparisons between other studies.
This measurement equipment can also be installed in an existing
machine and it can be programmed so that it measures in real time.
Thus, it could be used e.g. to control dampers.
Abstract: An adaptive Helmholtz resonator was designed and
adapted to hydraulics. The resonator was controlled by open- and
closed-loop controls so that 20 dB attenuation of the peak-to-peak
value of the pulsating pressure was maintained. The closed-loop
control was noted to be better, albeit it was slower because of its low
pressure and temperature variation, which caused variation in the
effective bulk modulus of the hydraulic system. Low-pressure
hydraulics contains air, which affects the stiffness of the hydraulics,
and temperature variation changes the viscosity of the oil. Thus, an
open-loop control loses its efficiency if a condition such as
temperature or the amount of air changes after calibration. The
instability of the low-pressure hydraulic system reduced the
operational frequency range of the Helmholtz resonator when
compared with the results of an analytical model.
Different dampers for hydraulics are presented. Then analytical
models of a hydraulic pipe and a hydraulic pipe with a Helmholtz
resonator are presented. The analytical models are based on the wave
equation of sound pressure. Finally, control methods and the results
of experiments are presented.
Abstract: The hydraulic actuated excavator, being a non-linear
mobile machine, encounters many uncertainties. There are
uncertainties in the hydraulic system in addition to the uncertain
nature of the load. The simulation results obtained in this study show
that there is a need for intelligent control of such machines and in
particular interval type-2 fuzzy controller is most suitable for
minimizing the position error of a typical excavator-s bucket under
load variations. We consider the model parameter uncertainties such
as hydraulic fluid leakage and friction. These are uncertainties which
also depend up on the temperature and alter bulk modulus and
viscosity of the hydraulic fluid. Such uncertainties together with the
load variations cause chattering of the bucket position. The interval
type-2 fuzzy controller effectively eliminates the chattering and
manages to control the end-effecter (bucket) position with positional
error in the order of few millimeters.