Abstract: In this paper, an approach for finding optimized
layouts for connecting PV units delivering maximum array output
power is suggested. The approach is based on considering the
different varying parameters of PV units that might be extracted from
a general two-diode model. These are mainly, solar irradiation,
reverse saturation currents, ideality factors, series and shunt
resistances in addition to operating temperature. The approach has
been tested on 19 possible 2×3 configurations and allowed to
determine the optimized configurations as well as examine the effects
of the different units- parameters on the maximum output power.
Thus, using this approach, standard arrays with n×m units can be
configured for maximum generated power and allows designing PV
based systems having reduced surfaces to fit specific required power,
as it is the case for solar cars and other mobile systems.
Abstract: This paper systematically investigates the timedependent
health outcomes for office staff during computer work
using the developed mathematical model. The model describes timedependent
health outcomes in multiple body regions associated with
computer usage. The association is explicitly presented with a doseresponse
relationship which is parametrized by body region
parameters. Using the developed model we perform extensive
investigations of the health outcomes statically and dynamically. We
compare the risk body regions and provide various severity rankings
of the discomfort rate changes with respect to computer-related
workload dynamically for the study population. Application of the
developed model reveals a wide range of findings. Such broad
spectrum of investigations in a single report literature is lacking.
Based upon the model analysis, it is discovered that the highest
average severity level of the discomfort exists in neck, shoulder, eyes,
shoulder joint/upper arm, upper back, low back and head etc. The
biggest weekly changes of discomfort rates are in eyes, neck, head,
shoulder, shoulder joint/upper arm and upper back etc. The fastest
discomfort rate is found in neck, followed by shoulder, eyes, head,
shoulder joint/upper arm and upper back etc. Most of our findings are
consistent with the literature, which demonstrates that the developed
model and results are applicable and valuable and can be utilized to
assess correlation between the amount of computer-related workload
and health risk.
Abstract: The present study is concerned with the free
convective two dimensional flow and heat transfer, within the
framework of Boussinesq approximation, in anisotropic fluid filled
porous rectangular enclosure subjected to end-to-end temperature
difference have been investigated using Lattice Boltzmann method
fornon-Darcy flow model. Effects of the moving lid direction (top,
bottom, left, and right wall moving in the negative and positive x&ydirections),
number of moving walls (one or two opposite walls), the
sliding wall velocity, and four different constant temperatures
opposite walls cases (two surfaces are being insulated and the
twoother surfaces areimposed to be at constant hot and cold
temperature)have been conducted. The results obtained are discussed
in terms of the Nusselt number, vectors, contours, and isotherms.
Abstract: Cardiac pulse-related artifacts in the EEG recorded
simultaneously with fMRI are complex and highly variable. Their
effective removal is an unsolved problem. Our aim is to develop an
adaptive removal algorithm based on the matching pursuit (MP)
technique and to compare it to established methods using a visual
evoked potential (VEP). We recorded the VEP inside the static
magnetic field of an MR scanner (with artifacts) as well as in an
electrically shielded room (artifact free). The MP-based artifact
removal outperformed average artifact subtraction (AAS) and
optimal basis set removal (OBS) in terms of restoring the EEG field
map topography of the VEP. Subsequently, a dipole model was fitted
to the VEP under each condition using a realistic boundary element
head model. The source location of the VEP recorded inside the MR
scanner was closest to that of the artifact free VEP after cleaning
with the MP-based algorithm as well as with AAS. While none of the
tested algorithms offered complete removal, MP showed promising
results due to its ability to adapt to variations of latency, frequency
and amplitude of individual artifact occurrences while still utilizing a
common template.
Abstract: Thermodynamics characterization Sesame oil
extraction by Acetone, Hexane and Benzene has been evaluated. The
120 hours experimental Data were described by a simple
mathematical model. According to the simulation results and the
essential criteria, Acetone is superior to other solvents but under
certain conditions where oil extraction takes place Hexane is superior
catalyst.
Abstract: This study investigates the performance of radial basis function networks (RBFN) in forecasting the monthly CO2 emissions of an electric power utility. We also propose a method for input variable selection. This method is based on identifying the general relationships between groups of input candidates and the output. The effect that each input has on the forecasting error is examined by removing all inputs except the variable to be investigated from its group, calculating the networks parameter and performing the forecast. Finally, the new forecasting error is compared with the reference model. Eight input variables were identified as the most relevant, which is significantly less than our reference model with 30 input variables. The simulation results demonstrate that the model with the 8 inputs selected using the method introduced in this study performs as accurate as the reference model, while also being the most parsimonious.
Abstract: This article is dedicated to development of
mathematical models for determining the dynamics of
concentration of hazardous substances in urban turbulent
atmosphere. Development of the mathematical models implied
taking into account the time-space variability of the fields of
meteorological items and such turbulent atmosphere data as vortex
nature, nonlinear nature, dissipativity and diffusivity. Knowing the
turbulent airflow velocity is not assumed when developing the
model. However, a simplified model implies that the turbulent and
molecular diffusion ratio is a piecewise constant function that
changes depending on vertical distance from the earth surface.
Thereby an important assumption of vertical stratification of urban
air due to atmospheric accumulation of hazardous substances
emitted by motor vehicles is introduced into the mathematical
model. The suggested simplified non-linear mathematical model of
determining the sought exhaust concentration at a priori unknown
turbulent flow velocity through non-degenerate transformation is
reduced to the model which is subsequently solved analytically.
Abstract: The protection of parallel transmission lines has been a challenging task due to mutual coupling between the adjacent circuits of the line. This paper presents a novel scheme for detection and classification of faults on parallel transmission lines. The proposed approach uses combination of wavelet transform and neural network, to solve the problem. While wavelet transform is a powerful mathematical tool which can be employed as a fast and very effective means of analyzing power system transient signals, artificial neural network has a ability to classify non-linear relationship between measured signals by identifying different patterns of the associated signals. The proposed algorithm consists of time-frequency analysis of fault generated transients using wavelet transform, followed by pattern recognition using artificial neural network to identify the type of the fault. MATLAB/Simulink is used to generate fault signals and verify the correctness of the algorithm. The adaptive discrimination scheme is tested by simulating different types of fault and varying fault resistance, fault location and fault inception time, on a given power system model. The simulation results show that the proposed scheme for fault diagnosis is able to classify all the faults on the parallel transmission line rapidly and correctly.
Abstract: In this paper, a system level behavioural model for RF
power amplifier, which exhibits memory effects, and based on multibranch
system is proposed. When higher order terms are included,
the memory polynomial model (MPM) exhibits numerical
instabilities. A set of memory orthogonal polynomial model
(OMPM) is introduced to alleviate the numerical instability problem
associated to MPM model. A data scaling and centring algorithm was
applied to improve the power amplifier modeling accuracy.
Simulation results prove that the numerical instability can be greatly
reduced, as well as the model precision improved with nonlinear
model.
Abstract: This paper describes the development, modeling, and
testing of skyhook and MiniMax control strategies of semi-active
suspension. The control performances are investigated using
Matlab/Simulink [1], with a two-degree-of-freedom quarter car semiactive
suspension system model. The comparison and evaluation of
control result are made using software-in-the-loop simulation (SILS)
method. This paper also outlines the development of a hardware-inthe-
loop simulation (HILS) system. The simulation results show that
skyhook strategy can significantly reduce the resonant peak of body
and provide improvement in vehicle ride comfort. Otherwise,
MiniMax strategy can be employed to effectively improve drive
safety of vehicle by influencing wheel load. The two strategies can
be switched to control semi-active suspension system to fulfill
different requirement of vehicle in different stages.
Abstract: Large metal and concrete structures suffer by various kinds of deterioration, and accurate prediction of the remaining life is important. This paper informs about two methods for its assessment. One method, suitable for steel bridges and other constructions exposed to fatigue, monitors the loads and damage accumulation using information systems for the operation and the finite element model of the construction. In addition to the operation load, the dead weight of the construction and thermal stresses can be included into the model. The second method is suitable for concrete bridges and other structures, which suffer by carbonatation and other degradation processes, driven by diffusion. The diffusion constant, important for the prediction of future development, can be determined from the depth-profile of pH, obtained by pH measurement at various depths. Comparison with measurements on real objects illustrates the suitability of both methods.
Abstract: The construction of a civil structure inside a urban
area inevitably modifies the outdoor microclimate at the building
site. Wind speed, wind direction, air pollution, driving rain, radiation
and daylight are some of the main physical aspects that are subjected
to the major changes. The quantitative amount of these modifications
depends on the shape, size and orientation of the building and on its
interaction with the surrounding environment.The flow field over a
flat roof model building has been numerically investigated in order to
determine two-dimensional CFD guidelines for the calculation of the
turbulent flow over a structure immersed in an atmospheric boundary
layer. To this purpose, a complete validation campaign has been
performed through a systematic comparison of numerical simulations
with wind tunnel experimental data.Several turbulence models and
spatial node distributions have been tested for five different vertical
positions, respectively from the upstream leading edge to the
downstream bottom edge of the analyzed model. Flow field
characteristics in the neighborhood of the building model have been
numerically investigated, allowing a quantification of the capabilities
of the CFD code to predict the flow separation and the extension of
the recirculation regions.The proposed calculations have allowed the
development of a preliminary procedure to be used as a guidance in
selecting the appropriate grid configuration and corresponding
turbulence model for the prediction of the flow field over a twodimensional
roof architecture dominated by flow separation.
Abstract: This paper gives an overview of a deep drawing
process by pressurized liquid medium separated from the sheet by a
rubber diaphragm. Hydroforming deep drawing processing of sheet
metal parts provides a number of advantages over conventional
techniques. It generally increases the depth to diameter ratio possible
in cup drawing and minimizes the thickness variation of the drawn
cup. To explore the deformation mechanism, analytical and
numerical simulations are used for analyzing the drawing process of
an AA6061-T4 blank. The effects of key process parameters such as
coefficient of friction, initial thickness of the blank and radius
between cup wall and flange are investigated analytically and
numerically. The simulated results were in good agreement with the
results of the analytical model. According to finite element
simulations, the hydroforming deep drawing method provides a more
uniform thickness distribution compared to conventional deep
drawing and decreases the risk of tearing during the process.
Abstract: In this paper, fully developed flow and heat transfer of
viscoelastic materials in curved ducts with square cross section under
constant heat flux have been investigated. Here, staggered mesh is
used as computational grids and flow and heat transfer parameters
have been allocated in this mesh with marker and cell method.
Numerical solution of governing equations has being performed with
FTCS finite difference method. Furthermore, Criminale-Eriksen-
Filbey (CEF) constitutive equation has being used as viscoelastic
model. CEF constitutive equation is a suitable model for studying
steady shear flow of viscoelastic materials which is able to model
both effects of the first and second normal stress differences. Here, it
is shown that the first and second normal stresses differences have
noticeable and inverse effect on secondary flows intensity and mean
Nusselt number which is the main novelty of current research.
Abstract: In this paper, we apply a semismooth active set method to image inpainting. The method exploits primal and dual features of a proposed regularized total variation model, following after the technique presented in [4]. Numerical results show that the method is fast and efficient in inpainting sufficiently thin domains.
Abstract: Fuzzy C-means Clustering algorithm (FCM) is a
method that is frequently used in pattern recognition. It has the
advantage of giving good modeling results in many cases, although,
it is not capable of specifying the number of clusters by itself. In
FCM algorithm most researchers fix weighting exponent (m) to a
conventional value of 2 which might not be the appropriate for all
applications. Consequently, the main objective of this paper is to use
the subtractive clustering algorithm to provide the optimal number of
clusters needed by FCM algorithm by optimizing the parameters of
the subtractive clustering algorithm by an iterative search approach
and then to find an optimal weighting exponent (m) for the FCM
algorithm. In order to get an optimal number of clusters, the iterative
search approach is used to find the optimal single-output Sugenotype
Fuzzy Inference System (FIS) model by optimizing the
parameters of the subtractive clustering algorithm that give minimum
least square error between the actual data and the Sugeno fuzzy
model. Once the number of clusters is optimized, then two
approaches are proposed to optimize the weighting exponent (m) in
the FCM algorithm, namely, the iterative search approach and the
genetic algorithms. The above mentioned approach is tested on the
generated data from the original function and optimal fuzzy models
are obtained with minimum error between the real data and the
obtained fuzzy models.
Abstract: Two approaches for model development of a smart acoustic box are suggested in this paper: the finite element (FE) approach and the subspace identification. Both approaches result in a state-space model, which can be used for obtaining the frequency responses and for the controller design. In order to validate the developed FE model and to perform the subspace identification, an experimental set-up with the acoustic box and dSPACE system was used. Experimentally obtained frequency responses show good agreement with the frequency responses obtained from the FE model and from the identified model.
Abstract: In this article, the design of a Supply Chain Network
(SCN) consisting of several suppliers, production plants, distribution
centers and retailers, is considered. Demands of retailers are
considered stochastic parameters, so we generate amounts of data via
simulation to extract a few demand scenarios. Then a mixed integer
two-stage programming model is developed to optimize
simultaneously two objectives: (1) minimization the fixed and
variable cost, (2) maximization the service level. A weighting method
is utilized to solve this two objective problem and a numerical
example is made to show the performance of the model.
Abstract: An adaptive Fuzzy Inference Perceptual model has
been proposed for watermarking of digital images. The model
depends on the human visual characteristics of image sub-regions in
the frequency multi-resolution wavelet domain. In the proposed
model, a multi-variable fuzzy based architecture has been designed to
produce a perceptual membership degree for both candidate
embedding sub-regions and strength watermark embedding factor.
Different sizes of benchmark images with different sizes of
watermarks have been applied on the model. Several experimental
attacks have been applied such as JPEG compression, noises and
rotation, to ensure the robustness of the scheme. In addition, the
model has been compared with different watermarking schemes. The
proposed model showed its robustness to attacks and at the same time
achieved a high level of imperceptibility.
Abstract: Visual inputs are one of the key sources from which
humans perceive the environment and 'understand' what is
happening. Artificial systems perceive the visual inputs as digital
images. The images need to be processed and analysed. Within the
human brain, processing of visual inputs and subsequent
development of perception is one of its major functionalities. In this
paper we present part of our research project, which aims at the
development of an artificial model for visual perception (or
'understanding') based on the human perceptive and cognitive
systems. We propose a new model for perception from visual inputs
and a way of understaning or interpreting images using the model.
We demonstrate the implementation and use of the model with a real
image data set.